Skip to contentSkip to conversation

Dove: add support for CM-A510 machine.

PATCH Superseded Mike Rapoport 4 participants 7 messages Nov 15, 2010 – Nov 29, 2010

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 Dove: add support for CM-A510 machine.

From: Konstantin Sinyuk <[email protected]>

Hi Nicolas,
Can you please add the below patch to your orion tree? Saeed has already reviewed and approved the prevoius version.

v2 changes:
* rebase on top of current Linus tree
* remove .phys_io and .io_pg_offst from machine description

---

---
 arch/arm/mach-dove/Kconfig   |    6 +++
 arch/arm/mach-dove/Makefile  |    1 +
 arch/arm/mach-dove/cm-a510.c |   95 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 102 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-dove/cm-a510.c
arch/arm/mach-dove/Kconfig +6 -0
index 3b9a32a..a4ed390 100644
@@ -9,6 +9,12 @@ config MACH_DOVE_DB
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell DB-MV88AP510 Development Board.
 
+ config MACH_CM_A510
+	bool "CompuLab CM-A510 Board"
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  CompuLab CM-A510 Board.
+
 endmenu
 
 endif
arch/arm/mach-dove/Makefile +1 -0
index 7ab3be5..f74f549 100644
@@ -1,3 +1,4 @@
 obj-y				+= common.o addr-map.o irq.o pcie.o
 
 obj-$(CONFIG_MACH_DOVE_DB)	+= dove-db-setup.o
+obj-$(CONFIG_MACH_CM_A510)	+= cm-a510.o
arch/arm/mach-dove/cm-a510.c new file +95 -0

95 lines not on this page · raw message

Signature · 1 line
1.7.3.1
#1 lore raw

PATCH v2 1/1 Dove: add support for CM-A510 machine.

Mike,

Some minor comments below:

Quoted 5 lines · Mike Rapoport

From: Konstantin Sinyuk <[email protected]>

Hi Nicolas,
Can you please add the below patch to your orion tree? Saeed has already reviewed and approved the prevoius version.

Some better description of the patch rather than internal communication :)

Quoted 3 lines

v2 changes:
* rebase on top of current Linus tree
* remove .phys_io and .io_pg_offst from machine description

The changelog can go after the '---' line.

Quoted 3 lines

---

The signed-off-by lines will be ignored by 'git am' as they come after the '---' line. Should be moved above.

Signature · 1 line
Catalin
#2 lore raw

PATCH v2 1/1 Dove: add support for CM-A510 machine.

In reply to Mike Rapoport
Quoted 5 lines · Mike Rapoport

From: Konstantin Sinyuk <[email protected]>

Hi Nicolas,
Can you please add the below patch to your orion tree? Saeed has already reviewed and approved the prevoius version.

Sure. but please resent with the appropriate formatting for the commit log (Catalin pointed that out already) and add the Reviewed-by: tags from Saeed as appropriate.

Nicolas

#3 lore raw

PATCH v2 1/1 Dove: add support for CM-A510 machine.

From: Konstantin Sinyuk <[email protected]>

This patch adds support for CM-A510 machine

---
v2 changes:
* rebase on top of current Linus tree
* remove .phys_io and .io_pg_offst from machine description

 arch/arm/mach-dove/Kconfig   |    6 +++
 arch/arm/mach-dove/Makefile  |    1 +
 arch/arm/mach-dove/cm-a510.c |   95 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 102 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-dove/cm-a510.c
arch/arm/mach-dove/Kconfig +6 -0
index 3b9a32a..a4ed390 100644
@@ -9,6 +9,12 @@ config MACH_DOVE_DB
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell DB-MV88AP510 Development Board.
 
+ config MACH_CM_A510
+	bool "CompuLab CM-A510 Board"
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  CompuLab CM-A510 Board.
+
 endmenu
 
 endif
arch/arm/mach-dove/Makefile +1 -0
index 7ab3be5..f74f549 100644
@@ -1,3 +1,4 @@
 obj-y				+= common.o addr-map.o irq.o pcie.o
 
 obj-$(CONFIG_MACH_DOVE_DB)	+= dove-db-setup.o
+obj-$(CONFIG_MACH_CM_A510)	+= cm-a510.o
arch/arm/mach-dove/cm-a510.c new file +95 -0

95 lines not on this page · raw message

Signature · 1 line
1.7.3.1
#4 lore raw

PATCH v2 1/1 Dove: add support for CM-A510 machine.

Quoted 7 lines · Mike Rapoport

From: Konstantin Sinyuk <[email protected]>

This patch adds support for CM-A510 machine

Quoted 147 lines

---
v2 changes:
* rebase on top of current Linus tree
* remove .phys_io and .io_pg_offst from machine description

?arch/arm/mach-dove/Kconfig ? | ? ?6 +++
?arch/arm/mach-dove/Makefile ?| ? ?1 +
?arch/arm/mach-dove/cm-a510.c | ? 95 ++++++++++++++++++++++++++++++++++++++++++

?3 files changed, 102 insertions(+), 0 deletions(-) ?create mode 100644 arch/arm/mach-dove/cm-a510.c

arch/arm/mach-dove/Kconfig +0 -0
index 3b9a32a..a4ed390 100644
@@ -9,6 +9,12 @@ config MACH_DOVE_DB

? ? ? ? ?Say 'Y' here if you want your kernel to support the ? ? ? ? ?Marvell DB-MV88AP510 Development Board.

+ config MACH_CM_A510
+ ? ? ? bool "CompuLab CM-A510 Board"
+ ? ? ? help
+ ? ? ? ? Say 'Y' here if you want your kernel to support the
+ ? ? ? ? CompuLab CM-A510 Board.
+
?endmenu

?endif

arch/arm/mach-dove/Makefile +0 -0
index 7ab3be5..f74f549 100644
@@ -1,3 +1,4 @@

?obj-y ? ? ? ? ? ? ? ? ? ? ? ? ?+= common.o addr-map.o irq.o pcie.o

?obj-$(CONFIG_MACH_DOVE_DB) ? ? += dove-db-setup.o

arch/arm/mach-dove/Makefile +1 -0
+obj-$(CONFIG_MACH_CM_A510) ? ? += cm-a510.o
arch/arm/mach-dove/cm-a510.c new file +95 -1
new file mode 100644
index 0000000..96e0e94
@@ -0,0 +1,95 @@
+/*
+ * arch/arm/mach-dove/cm-a510.c
+ *
+ * Copyright (C) 2010 CompuLab, Ltd.
+ * Konstantin Sinyuk <[email protected]>
+ *
+ * Based on Marvell DB-MV88AP510-BP Development Board Setup
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. ?This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/ata_platform.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <mach/dove.h>
+
+#include "common.h"
+
+static struct mv643xx_eth_platform_data cm_a510_ge00_data = {
+ ? ? ? .phy_addr ? ? ? = MV643XX_ETH_PHY_ADDR_DEFAULT,
+};
+
+static struct mv_sata_platform_data cm_a510_sata_data = {
+ ? ? ? .n_ports ? ? ? ?= 1,
+};
+
+/*
+ * SPI Devices:
+ * SPI0: 1M Flash Winbond w25q32bv
+ */
+static const struct flash_platform_data cm_a510_spi_flash_data = {
+ ? ? ? .type ? ? ? ? ? = "w25q32bv",
+};
+
+static struct spi_board_info __initdata cm_a510_spi_flash_info[] = {
+ ? ? ? {
+ ? ? ? ? ? ? ? .modalias ? ? ? = "m25p80",
+ ? ? ? ? ? ? ? .platform_data ?= &cm_a510_spi_flash_data,
+ ? ? ? ? ? ? ? .irq ? ? ? ? ? ?= -1,
+ ? ? ? ? ? ? ? .max_speed_hz ? = 20000000,
+ ? ? ? ? ? ? ? .bus_num ? ? ? ?= 0,
+ ? ? ? ? ? ? ? .chip_select ? ?= 0,
+ ? ? ? },
+};
+
+static int __init cm_a510_pci_init(void)
+{
+ ? ? ? if (machine_is_cm_a510())
+ ? ? ? ? ? ? ? dove_pcie_init(1, 1);
+
+ ? ? ? return 0;
+}
+
+subsys_initcall(cm_a510_pci_init);
+
+/* Board Init */
+static void __init cm_a510_init(void)
+{
+ ? ? ? /*
+ ? ? ? ?* Basic Dove setup. Needs to be called early.
+ ? ? ? ?*/
+ ? ? ? dove_init();
+
+ ? ? ? dove_ge00_init(&cm_a510_ge00_data);
+ ? ? ? dove_ehci0_init();
+ ? ? ? dove_ehci1_init();
+ ? ? ? dove_sata_init(&cm_a510_sata_data);
+ ? ? ? dove_sdio0_init();
+ ? ? ? dove_sdio1_init();
+ ? ? ? dove_spi0_init();
+ ? ? ? dove_spi1_init();
+ ? ? ? dove_uart0_init();
+ ? ? ? dove_uart1_init();
+ ? ? ? dove_i2c_init();
+ ? ? ? spi_register_board_info(cm_a510_spi_flash_info,
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ARRAY_SIZE(cm_a510_spi_flash_info));
+}
+
+MACHINE_START(CM_A510, "Compulab CM-A510 Board")
+ ? ? ? .boot_params ? ?= 0x00000100,
+ ? ? ? .init_machine ? = cm_a510_init,
+ ? ? ? .map_io ? ? ? ? = dove_map_io,
+ ? ? ? .init_irq ? ? ? = dove_init_irq,
+ ? ? ? .timer ? ? ? ? ?= &dove_timer,
+MACHINE_END
--

1.7.3.1

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#5 lore raw

PATCH v2 1/1 Dove: add support for CM-A510 machine.

Hi Nicolas,

Any updates on this?

Quoted 156 lines · saeed bishara
Quoted 7 lines · Mike Rapoport

From: Konstantin Sinyuk <[email protected]>

This patch adds support for CM-A510 machine

Quoted 147 lines

---
v2 changes:
* rebase on top of current Linus tree
* remove .phys_io and .io_pg_offst from machine description

 arch/arm/mach-dove/Kconfig   |    6 +++
 arch/arm/mach-dove/Makefile  |    1 +
 arch/arm/mach-dove/cm-a510.c |   95 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 102 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-dove/cm-a510.c
arch/arm/mach-dove/Kconfig +6 -0
index 3b9a32a..a4ed390 100644
@@ -9,6 +9,12 @@ config MACH_DOVE_DB
         Say 'Y' here if you want your kernel to support the
         Marvell DB-MV88AP510 Development Board.
 
+ config MACH_CM_A510
+       bool "CompuLab CM-A510 Board"
+       help
+         Say 'Y' here if you want your kernel to support the
+         CompuLab CM-A510 Board.
+
 endmenu
 
 endif
arch/arm/mach-dove/Makefile +1 -0
index 7ab3be5..f74f549 100644
@@ -1,3 +1,4 @@
 obj-y                          += common.o addr-map.o irq.o pcie.o
 
 obj-$(CONFIG_MACH_DOVE_DB)     += dove-db-setup.o
+obj-$(CONFIG_MACH_CM_A510)     += cm-a510.o
arch/arm/mach-dove/cm-a510.c new file +95 -1
new file mode 100644
index 0000000..96e0e94
@@ -0,0 +1,95 @@
+/*
+ * arch/arm/mach-dove/cm-a510.c
+ *
+ * Copyright (C) 2010 CompuLab, Ltd.
+ * Konstantin Sinyuk <[email protected]>
+ *
+ * Based on Marvell DB-MV88AP510-BP Development Board Setup
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/ata_platform.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <mach/dove.h>
+
+#include "common.h"
+
+static struct mv643xx_eth_platform_data cm_a510_ge00_data = {
+       .phy_addr       = MV643XX_ETH_PHY_ADDR_DEFAULT,
+};
+
+static struct mv_sata_platform_data cm_a510_sata_data = {
+       .n_ports        = 1,
+};
+
+/*
+ * SPI Devices:
+ * SPI0: 1M Flash Winbond w25q32bv
+ */
+static const struct flash_platform_data cm_a510_spi_flash_data = {
+       .type           = "w25q32bv",
+};
+
+static struct spi_board_info __initdata cm_a510_spi_flash_info[] = {
+       {
+               .modalias       = "m25p80",
+               .platform_data  = &cm_a510_spi_flash_data,
+               .irq            = -1,
+               .max_speed_hz   = 20000000,
+               .bus_num        = 0,
+               .chip_select    = 0,
+       },
+};
+
+static int __init cm_a510_pci_init(void)
+{
+       if (machine_is_cm_a510())
+               dove_pcie_init(1, 1);
+
+       return 0;
+}
+
+subsys_initcall(cm_a510_pci_init);
+
+/* Board Init */
+static void __init cm_a510_init(void)
+{
+       /*
+        * Basic Dove setup. Needs to be called early.
+        */
+       dove_init();
+
+       dove_ge00_init(&cm_a510_ge00_data);
+       dove_ehci0_init();
+       dove_ehci1_init();
+       dove_sata_init(&cm_a510_sata_data);
+       dove_sdio0_init();
+       dove_sdio1_init();
+       dove_spi0_init();
+       dove_spi1_init();
+       dove_uart0_init();
+       dove_uart1_init();
+       dove_i2c_init();
+       spi_register_board_info(cm_a510_spi_flash_info,
+                               ARRAY_SIZE(cm_a510_spi_flash_info));
+}
+
+MACHINE_START(CM_A510, "Compulab CM-A510 Board")
+       .boot_params    = 0x00000100,
+       .init_machine   = cm_a510_init,
+       .map_io         = dove_map_io,
+       .init_irq       = dove_init_irq,
+       .timer          = &dove_timer,
+MACHINE_END
--

1.7.3.1

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Signature · 2 lines
Sincerely yours,
Mike.
#6 lore raw

PATCH v2 1/1 Dove: add support for CM-A510 machine.

Quoted 3 lines · Mike Rapoport

Hi Nicolas,

Any updates on this?

Pushed to the orion repo.

Nicolas