Bug#618930: High network latency with ralink usb wireless device
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): 1300555815.26693.83.camel@localhost
(see also bugs.debian.org/618930 though AFAIK everything important is reproduced in this message.)
Quoted 2 lines · Ben Hutchings
Sorry, no. Please report this upstream to [email protected] and cc the bug address.
I have a TP-Link TL-WN321G USB wireless adapter, which is a badged Ralink RT2070. Under Debian's 2.6.32 this worked smoothly with rt2870sta. On upgrading to Debian's 2.6.38, however, only rt2800usb was available and with that I found that ping latency is around 600ms.
== Under 2.6.32, with rt2870sta ==
richard@violeer:~$ uname -a Linux violeer 2.6.32-5-686 #1 SMP Wed Jan 12 04:01:41 UTC 2011 i686 GNU/Linux richard@violeer:~$ iwconfig lo no wireless extensions.
eth0 no wireless extensions.
wlan0 Ralink STA ESSID:"wlan.anjou.terraraq.org.uk" Nickname:"RT2870STA"
Mode:Managed Frequency=2.442 GHz Access Point:
00:0F:CB:A0:0C:70
Bit Rate=54 Mb/s
RTS thr:off Fragment thr:off
Link Quality=100/100 Signal level:-45 dBm Noise level:-83 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
richard@sfere:~$ ping -qc10 violeer PING violeer.wlan.anjou.terraraq.org.uk (172.31.59.138) 56(84) bytes of data.
--- violeer.wlan.anjou.terraraq.org.uk ping statistics --- 10 packets transmitted, 10 received, 0% packet loss, time 9013ms rtt min/avg/max/mdev = 0.973/1.094/1.490/0.141 ms
== Under 2.6.38, with rt2800usb ==
richard@violeer:~$ uname -a Linux violeer 2.6.38-1-686 #1 SMP Wed Mar 16 17:37:47 UTC 2011 i686 GNU/Linux richard@violeer:~$ iwconfig lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bg ESSID:"wlan.anjou.terraraq.org.uk"
Mode:Managed Frequency:2.442 GHz Access Point:
00:0F:CB:A0:0C:70
Bit Rate=18 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:on
Link Quality=67/70 Signal level=-43 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:2 Invalid misc:6 Missed beacon:0
richard@sfere:~$ ping -qc10 violeer PING violeer.wlan.anjou.terraraq.org.uk (172.31.59.138) 56(84) bytes of data.
--- violeer.wlan.anjou.terraraq.org.uk ping statistics --- 10 packets transmitted, 10 received, 0% packet loss, time 9006ms rtt min/avg/max/mdev = 509.111/603.472/630.232/47.090 ms
== lsusb output ==
Bus 001 Device 002: ID 148f:2070 Ralink Technology, Corp. RT2070 Wireless Adapter Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x148f Ralink Technology, Corp. idProduct 0x2070 RT2070 Wireless Adapter bcdDevice 1.01 iManufacturer 1 Ralink iProduct 2 802.11 g WLAN iSerial 3 1.0 bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 67
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 450mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 7
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 5 1.0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x06 EP 6 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
== dmesg output ==
root@violeer:~# dmesg|grep -E rt2\|wlan [ 12.344624] Registered led device: rt2800usb-phy0::radio [ 12.344653] Registered led device: rt2800usb-phy0::assoc [ 12.344679] Registered led device: rt2800usb-phy0::quality [ 12.346539] usbcore: registered new interface driver rt2800usb [ 14.895564] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 18.829895] wlan0: authenticate with 00:0f:cb:a0:0c:70 (try 1) [ 18.831281] wlan0: authenticated [ 20.432339] wlan0: associate with 00:0f:cb:a0:0c:70 (try 1) [ 20.434597] wlan0: RX AssocResp from 00:0f:cb:a0:0c:70 (capab=0x431 status=0 aid=2) [ 20.434601] wlan0: associated [ 20.442967] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Quoted 1 line · Richard Kettlewell
(see also bugs.debian.org/618930
...
Quoted 5 lines
I have a TP-Link TL-WN321G USB wireless adapter, which is a badged Ralink RT2070. Under Debian's 2.6.32 this worked smoothly with rt2870sta. On upgrading to Debian's 2.6.38, however, only rt2800usb was available and with that I found that ping latency is around 600ms.
...
Quoted 1 line
Power Management:on
I sent a patch to disable power save by default, but then work started to fix it instead, but then stalled. Seems like 2.6.38 shipped with broken power save enabled by default. Plese read the discussion following my RFC patch:
http://rt2x00.serialmonkey.com/pipermail/users_rt2x00.serialmonkey.com/2011-January/thread.html#3017
You can test if power saving causes your issue by disabling it with "iwconfig wlan0 power off".
Johannes
Quoted 11 lines
I sent a patch to disable power save by default, but then work started
to fix it instead, but then stalled. Seems like 2.6.38 shipped with
broken power save enabled by default. Plese read the discussion
following my RFC patch:
http://rt2x00.serialmonkey.com/pipermail/users_rt2x00.serialmonkey.com/2011-January/thread.html#3017
Quoted 4 lines
You can test if power saving causes your issue by
disabling
it with "iwconfig wlan0 power off".
Hi Johannes
Does this patch touches on lost and duplicate packets with rt3070 USB as well?
Walter
Quoted 8 lines · Johannes Stezenbach
I sent a patch to disable power save by default, but then work started to fix it instead, but then stalled. Seems like 2.6.38 shipped with broken power save enabled by default. Plese read the discussion following my RFC patch:
http://rt2x00.serialmonkey.com/pipermail/users_rt2x00.serialmonkey.com/2011-January/thread.html#3017You can test if power saving causes your issue by disabling it with "iwconfig wlan0 power off".
That does the trick - thanks!
richard@sfere:~$ ssh violeer uname -a Linux violeer 2.6.38-1-686 #1 SMP Wed Mar 16 17:37:47 UTC 2011 i686 GNU/Linux richard@sfere:~$ ping -qc10 violeer PING violeer.wlan.anjou.terraraq.org.uk (172.31.59.138) 56(84) bytes of data.
--- violeer.wlan.anjou.terraraq.org.uk ping statistics --- 10 packets transmitted, 10 received, 0% packet loss, time 9016ms rtt min/avg/max/mdev = 0.919/0.981/1.089/0.057 ms richard@sfere:~$
ttfn/rjk
Re: High network latency with ralink usb wireless device
Hi Ben,
About a year ago, Richard Kettlewell wrote[1]:
Quoted 8 lines · Johannes Stezenbach
Quoted 7 lines
I sent a patch to disable power save by default, but then work started to fix it instead, but then stalled. Seems like 2.6.38 shipped with broken power save enabled by default. Plese read the discussion following my RFC patch:
http://rt2x00.serialmonkey.com/pipermail/users_rt2x00.serialmonkey.com/2011-January/thread.html#3017
Quoted 4 lines
Quoted 2 lines
You can test if power saving causes your issue by disabling it with "iwconfig wlan0 power off".
That does the trick - thanks!
Therefore ever since version 2.6.38-2, Debian kernels have had powersaving disabled on rt2800usb devices.
I think we should revisit this in light of
v3.0-rc2~7^2~16^2~190 rt2x00: Add autowake support for USB hardware (2011-04-30)
though I wouldn't be surprised if testing ends up revealing some followup patches introduced after v3.2 to be needed for it to work well. What do you think?
Thanks,
Jonathan