Pull request: u-boot-imx

Hi Albert,

The following changes since commit 67a490d60d70f2b01d55976440ba30154af96965:

atmel_nand: don't require CONFIG_SYS_NAND_ENABLE_PIN (2011-04-01
14:49:08 -0500)

are available in the git repository at:
git://www.denx.de/git/u-boot-imx.git master

Fabio Estevam (1):
mx25: Make the UART port number explicit in its setup function

Jason Liu (2):
mx53loco: set mmc env to MMC slot1
MX5: Enable flat-device-tree support on mx53 loco board

Liu Hui-R64343 (3):
MX53: drop config.mk from mx53evk
MX53: support for freescale MX53LOCO board
MX5: Enable flat-device-tree support on mx51/53 evk board

Stefano Babic (5):
Makefile: change rule to build IMX image
MX51: drop config.mk from mx51evk
MX31: add support for MX31 watchdog
MX31: qong: add watchdog
IMX: MX31: Cleanup include files and drop nasty #ifdef in drivers

 MAINTAINERS                                        |    1 +
 Makefile                                           |    2 +-
 arch/arm/cpu/arm1136/mx31/devices.c                |    4 +-
 arch/arm/cpu/arm1136/mx31/generic.c                |    2 +-
 arch/arm/cpu/arm1136/mx31/timer.c                  |   40 +++-
 arch/arm/cpu/arm926ejs/mx25/generic.c              |    2 +-
 arch/arm/include/asm/arch-mx31/{mx31.h => clock.h} |    6 +-
 .../asm/arch-mx31/{mx31-regs.h => imx-regs.h}      |   10 +
 board/davedenx/qong/fpga.c                         |    4 +-
 board/davedenx/qong/lowlevel_init.S                |    2 +-
 board/davedenx/qong/qong.c                         |   16 +-
 board/freescale/mx31ads/lowlevel_init.S            |    2 +-
 board/freescale/mx31ads/mx31ads.c                  |    4 +-
 board/freescale/mx31pdk/lowlevel_init.S            |    2 +-
 board/freescale/mx31pdk/mx31pdk.c                  |    4 +-
 board/freescale/mx53evk/config.mk                  |   24 --
 .../{mx51evk/config.mk => mx53loco/Makefile}       |   36 ++-
 board/freescale/mx53loco/imximage.cfg              |   96 ++++++
 board/freescale/mx53loco/mx53loco.c                |  316
++++++++++++++++++++
 board/imx31_phycore/imx31_phycore.c                |    4 +-
 board/imx31_phycore/lowlevel_init.S                |    2 +-
 board/karo/tx25/tx25.c                             |    4 +-
 board/logicpd/imx31_litekit/imx31_litekit.c        |    4 +-
 board/logicpd/imx31_litekit/lowlevel_init.S        |    2 +-
 boards.cfg                                         |    5 +-
 drivers/gpio/mxc_gpio.c                            |    5 -
 drivers/i2c/mxc_i2c.c                              |    7 +-
 drivers/serial/serial_mxc.c                        |    4 -
 drivers/spi/mxc_spi.c                              |    9 +-
 drivers/usb/host/ehci-mxc.c                        |    2 +-
 drivers/video/mx3fb.c                              |    6 +-
 include/configs/imx31_litekit.h                    |    2 +-
 include/configs/mx31ads.h                          |    2 +-
 include/configs/mx31pdk.h                          |    2 +-
 include/configs/mx51evk.h                          |    5 +
 include/configs/mx53evk.h                          |    3 +
 include/configs/mx53loco.h                         |  199 ++++++++++++
 include/configs/qong.h                             |    3 +-
 nand_spl/nand_boot_fsl_nfc.c                       |    4 -
 39 files changed, 751 insertions(+), 96 deletions(-)
 rename arch/arm/include/asm/arch-mx31/{mx31.h => clock.h} (92%)
 rename arch/arm/include/asm/arch-mx31/{mx31-regs.h => imx-regs.h} (99%)
 delete mode 100644 board/freescale/mx53evk/config.mk
 rename board/freescale/{mx51evk/config.mk => mx53loco/Makefile} (51%)
 create mode 100755 board/freescale/mx53loco/imximage.cfg
 create mode 100755 board/freescale/mx53loco/mx53loco.c
 create mode 100644 include/configs/mx53loco.h

Best regards,
Stefano

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================

Hi Stefano,

Le 05/04/2011 15:29, Stefano Babic a ?crit :

Applied, thanks.

Amicalement,

Albert.