arm: Tegra2: add support for A9 CPU init

arch/arm/cpu/armv7/tegra2/ap20.c new file +105 -0

new file mode 100644
index 0000000..075341e
@@ -0,0 +1,325 @@
+/*
+* (C) Copyright 2010-2011
+* NVIDIA Corporation<www.nvidia.com>
+*
+* See file CREDITS for list of people who contributed to this
+* project.
+*
+* This program is free software; you can redistribute it and/or
+* modify it under the terms of the GNU General Public License as
+* published by the Free Software Foundation; either version 2 of
+* the License, or (at your option) any later version.
+*
+* This program is distributed in the hope that it will be useful,
+* but WITHOUT ANY WARRANTY; without even the implied warranty of
+* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+* GNU General Public License for more details.
+*
+* You should have received a copy of the GNU General Public License
+* along with this program; if not, write to the Free Software
+* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+* MA 02111-1307 USA
+*/
+
+#include "ap20.h"
+#include<asm/io.h>
+#include<asm/arch/tegra2.h>
+#include<asm/arch/clk_rst.h>
+#include<asm/arch/pmc.h>
+#include<asm/arch/pinmux.h>
+#include<asm/arch/scu.h>
+#include<common.h>
+
+u32 s_first_boot = 1;
+
+static void enable_cpu_clock(int enable)
+{
+	struct clk_rst_ctlr *clkrst = (struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE;
+	u32 reg, clk;
+
+	/*
+	 * NOTE:
+	 * Regardless of whether the request is to enable or disable the CPU
+	 * clock, every processor in the CPU complex except the master (CPU 0)
+	 * will have it's clock stopped because the AVP only talks to the
+	 * master. The AVP does not know (nor does it need to know) that there
+	 * are multiple processors in the CPU complex.
+	 */
+
+	if (enable) {
+		/* Wait until all clocks are stable */
+		udelay(PLL_STABILIZATION_DELAY);
+
+		writel(CCLK_BURST_POLICY,&clkrst->crc_cclk_brst_pol);
+		writel(SUPER_CCLK_DIVIDER,&clkrst->crc_super_cclk_div);
+	}
+
+	/* Fetch the register containing the main CPU complex clock enable */
+	reg = readl(&clkrst->crc_clk_out_enb_l);
+	reg |= CLK_ENB_CPU;
+
+	/*
+	 * Read the register containing the individual CPU clock enables and
+	 * always stop the clock to CPU 1.
+	 */
+	clk = readl(&clkrst->crc_clk_cpu_cmplx);
+	clk |= CPU1_CLK_STP;
+
+	if (enable) {
+		/* Unstop the CPU clock */
+		clk&= ~CPU0_CLK_STP;
+	} else {
+		/* Stop the CPU clock */
+		clk |= CPU0_CLK_STP;
+	}
+
+	writel(clk,&clkrst->crc_clk_cpu_cmplx);
+	writel(reg,&clkrst->crc_clk_out_enb_l);
+}
+
+static int is_cpu_powered(void)
+{
+	struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
+
+	return (readl(&pmc->pmc_pwrgate_status)&  CPU_PWRED) ? 1 : 0;
+}
+
+static void remove_cpu_io_clamps(void)
+{
+	struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
+	u32 reg;
+
+	/* Remove the clamps on the CPU I/O signals */
+	reg = readl(&pmc->pmc_remove_clamping);
+	reg |= CPU_CLMP;
+	writel(reg,&pmc->pmc_remove_clamping);
+
+	/* Give I/O signals time to stabilize */
+	udelay(IO_STABILIZATION_DELAY);
+}
+
+static void powerup_cpu(void)
+{
+	struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
+	u32 reg;
+

arch/arm/cpu/armv7/tegra2/ap20.c new file +118 -0

+		/*
+		 * Remove the I/O clamps from CPU power partition.
+		 * Recommended only on a Warm boot, if the CPU partition gets
+		 * power gated. Shouldn't cause any harm when called after a
+		 * cold boot according to HW, probably just redundant.
+		 */
+		remove_cpu_io_clamps();
+	}
+}
+
+static void enable_cpu_power_rail(void)
+{
+	struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
+	u32 reg;
+
+	reg = readl(&pmc->pmc_cntrl);
+	reg |= CPUPWRREQ_OE;
+	writel(reg,&pmc->pmc_cntrl);
+
+	/*
+	 * The TI PMU65861C needs a 3.75ms delay between enabling
+	 * the power rail and enabling the CPU clock.  This delay
+	 * between SM1EN and SM1 is for switching time + the ramp
+	 * up of the voltage to the CPU (VDD_CPU from PMU).
+	 */
+	udelay(3750);
+}
+
+static void reset_A9_cpu(int reset)
+{
+	struct clk_rst_ctlr *clkrst = (struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE;
+	u32 reg, cpu;
+
+	/*
+	* NOTE:  Regardless of whether the request is to hold the CPU in reset
+	*        or take it out of reset, every processor in the CPU complex
+	*        except the master (CPU 0) will be held in reset because the
+	*        AVP only talks to the master. The AVP does not know that there
+	*        are multiple processors in the CPU complex.
+	*/
+
+	/* Hold CPU 1 in reset */
+	cpu = SET_DBGRESET1 | SET_DERESET1 | SET_CPURESET1;
+	writel(cpu,&clkrst->crc_cpu_cmplx_set);
+
+	reg = readl(&clkrst->crc_rst_dev_l);
+	if (reset) {
+		/* Now place CPU0 into reset */
+		cpu |= SET_DBGRESET0 | SET_DERESET0 | SET_CPURESET0;
+		writel(cpu,&clkrst->crc_cpu_cmplx_set);
+
+		/* Enable master CPU reset */
+		reg |= SWR_CPU_RST;
+	} else {
+		/* Take CPU0 out of reset */
+		cpu = CLR_DBGRESET0 | CLR_DERESET0 | CLR_CPURESET0;
+		writel(cpu,&clkrst->crc_cpu_cmplx_clr);
+
+		/* Disable master CPU reset */
+		reg&= ~SWR_CPU_RST;
+	}
+
+	writel(reg,&clkrst->crc_rst_dev_l);
+}
+
+static void clock_enable_coresight(int enable)
+{
+	struct clk_rst_ctlr *clkrst = (struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE;
+	u32 rst, clk, src;
+
+	rst = readl(&clkrst->crc_rst_dev_u);
+	clk = readl(&clkrst->crc_clk_out_enb_u);
+
+	if (enable) {
+		rst&= ~SWR_CSITE_RST;
+		clk |= CLK_ENB_CSITE;
+	} else {
+		rst |= SWR_CSITE_RST;
+		clk&= ~CLK_ENB_CSITE;
+	}
+
+	writel(clk,&clkrst->crc_clk_out_enb_u);
+	writel(rst,&clkrst->crc_rst_dev_u);
+
+	if (enable) {
+		/*
+		 * Put CoreSight on PLLP_OUT0 (216 MHz) and divide it down by
+		 *  1.5, giving an effective frequency of 144MHz.
+		 * Set PLLP_OUT0 [bits31:30 = 00], and use a 7.1 divisor
+		 *  (bits 7:0), so 00000001b == 1.5 (n+1 + .5)
+		 */
+		src = CLK_DIVIDER(NVBL_PLLP_KHZ, 144000);
+		writel(src,&clkrst->crc_clk_src_csite);
+
+		/* Unlock the CPU CoreSight interfaces */
+		rst = 0xC5ACCE55;
+		writel(rst, CSITE_CPU_DBG0_LAR);
+		writel(rst, CSITE_CPU_DBG1_LAR);
+	}
+}
+
+void start_cpu(u32 reset_vector)
+{
+	/* Enable VDD_CPU */
+	enable_cpu_power_rail();
+
+	/* Hold the CPUs in reset */
+	reset_A9_cpu(1);
+
+	/* Disable the CPU clock */
+	enable_cpu_clock(0);
+
+	/* Enable CoreSight */
+	clock_enable_coresight(1);
+
+	/*
+	 * Set the entry point for CPU execution from reset,
+	 *  if it's a non-zero value.

Le 12/04/2011 23:02, Tom Warren a ?crit :

Quoted 122 lines

arch/arm/cpu/armv7/tegra2/ap20.c new file +37 -0

new file mode 100644
index 0000000..075341e
@@ -0,0 +1,325 @@
+/*
+* (C) Copyright 2010-2011
+* NVIDIA Corporation<www.nvidia.com>
+*
+* See file CREDITS for list of people who contributed to this
+* project.
+*
+* This program is free software; you can redistribute it and/or
+* modify it under the terms of the GNU General Public License as
+* published by the Free Software Foundation; either version 2 of
+* the License, or (at your option) any later version.
+*
+* This program is distributed in the hope that it will be useful,
+* but WITHOUT ANY WARRANTY; without even the implied warranty of
+* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the
+* GNU General Public License for more details.
+*
+* You should have received a copy of the GNU General Public License
+* along with this program; if not, write to the Free Software
+* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+* MA 02111-1307 USA
+*/
+
+#include "ap20.h"
+#include<asm/io.h>
+#include<asm/arch/tegra2.h>
+#include<asm/arch/clk_rst.h>
+#include<asm/arch/pmc.h>
+#include<asm/arch/pinmux.h>
+#include<asm/arch/scu.h>
+#include<common.h>
+
+u32 s_first_boot = 1;
+
+static void enable_cpu_clock(int enable)
+{
+ ? ? ? struct clk_rst_ctlr *clkrst = (struct clk_rst_ctlr

*)NV_PA_CLK_RST_BASE;
+ ? ? ? u32 reg, clk;
+
+ ? ? ? /*
+ ? ? ? ?* NOTE:
+ ? ? ? ?* Regardless of whether the request is to enable or disable the CPU
+ ? ? ? ?* clock, every processor in the CPU complex except the master (CPU 0)
+ ? ? ? ?* will have it's clock stopped because the AVP only talks to the
+ ? ? ? ?* master. The AVP does not know (nor does it need to know) that there
+ ? ? ? ?* are multiple processors in the CPU complex.
+ ? ? ? ?*/

arch/arm/cpu/armv7/tegra2/ap20.c new file +10 -0

+
+ ? ? ? if (enable) {
+ ? ? ? ? ? ? ? /* Wait until all clocks are stable */
+ ? ? ? ? ? ? ? udelay(PLL_STABILIZATION_DELAY);
+
+ ? ? ? ? ? ? ? writel(CCLK_BURST_POLICY,&clkrst->crc_cclk_brst_pol);
+ ? ? ? ? ? ? ? writel(SUPER_CCLK_DIVIDER,&clkrst->crc_super_cclk_div);
+ ? ? ? }
+
+ ? ? ? /* Fetch the register containing the main CPU complex clock enable

*/
+ ? ? ? reg = readl(&clkrst->crc_clk_out_enb_l);
+ ? ? ? reg |= CLK_ENB_CPU;
+
+ ? ? ? /*
+ ? ? ? ?* Read the register containing the individual CPU clock enables and
+ ? ? ? ?* always stop the clock to CPU 1.
+ ? ? ? ?*/
+ ? ? ? clk = readl(&clkrst->crc_clk_cpu_cmplx);
+ ? ? ? clk |= CPU1_CLK_STP;

arch/arm/cpu/armv7/tegra2/ap20.c new file +43 -0

+
+ ? ? ? if (enable) {
+ ? ? ? ? ? ? ? /* Unstop the CPU clock */
+ ? ? ? ? ? ? ? clk&= ~CPU0_CLK_STP;
+ ? ? ? } else {
+ ? ? ? ? ? ? ? /* Stop the CPU clock */
+ ? ? ? ? ? ? ? clk |= CPU0_CLK_STP;
+ ? ? ? }
+
+ ? ? ? writel(clk,&clkrst->crc_clk_cpu_cmplx);
+ ? ? ? writel(reg,&clkrst->crc_clk_out_enb_l);
+}
+
+static int is_cpu_powered(void)
+{
+ ? ? ? struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
+
+ ? ? ? return (readl(&pmc->pmc_pwrgate_status)& ?CPU_PWRED) ? 1 : 0;
+}
+
+static void remove_cpu_io_clamps(void)
+{
+ ? ? ? struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
+ ? ? ? u32 reg;
+
+ ? ? ? /* Remove the clamps on the CPU I/O signals */
+ ? ? ? reg = readl(&pmc->pmc_remove_clamping);
+ ? ? ? reg |= CPU_CLMP;
+ ? ? ? writel(reg,&pmc->pmc_remove_clamping);
+
+ ? ? ? /* Give I/O signals time to stabilize */
+ ? ? ? udelay(IO_STABILIZATION_DELAY);
+}
+
+static void powerup_cpu(void)
+{
+ ? ? ? struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
+ ? ? ? u32 reg;
+
+ ? ? ? if (!is_cpu_powered()) {
+ ? ? ? ? ? ? ? /* Toggle the CPU power state (OFF -> ?ON) */
+ ? ? ? ? ? ? ? reg = readl(&pmc->pmc_pwrgate_toggle);
+ ? ? ? ? ? ? ? reg&= PARTID_CP;

Quoted 6 lines

+ ? ? ? ? ? ? ? reg |= START_CP;
+ ? ? ? ? ? ? ? writel(reg,&pmc->pmc_pwrgate_toggle); +
+ ? ? ? ? ? ? ? /* Wait for the power to come up */
+ ? ? ? ? ? ? ? while (!is_cpu_powered())
+ ? ? ? ? ? ? ? ? ? ? ? ; ? ? ? ? ? ? ? ? ? ? ? /* Do nothing */

What if power never comes up?

Quoted 134 lines

+ ? ? ? ? ? ? ? /*
+ ? ? ? ? ? ? ? ?* Remove the I/O clamps from CPU power partition.
+ ? ? ? ? ? ? ? ?* Recommended only on a Warm boot, if the CPU partition gets
+ ? ? ? ? ? ? ? ?* power gated. Shouldn't cause any harm when called after a
+ ? ? ? ? ? ? ? ?* cold boot according to HW, probably just redundant.
+ ? ? ? ? ? ? ? ?*/
+ ? ? ? ? ? ? ? remove_cpu_io_clamps();
+ ? ? ? }

arch/arm/cpu/armv7/tegra2/ap20.c new file +23 -0

+}
+
+static void enable_cpu_power_rail(void)
+{
+ ? ? ? struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
+ ? ? ? u32 reg;
+
+ ? ? ? reg = readl(&pmc->pmc_cntrl);
+ ? ? ? reg |= CPUPWRREQ_OE;
+ ? ? ? writel(reg,&pmc->pmc_cntrl);
+
+ ? ? ? /*
+ ? ? ? ?* The TI PMU65861C needs a 3.75ms delay between enabling
+ ? ? ? ?* the power rail and enabling the CPU clock. ?This delay
+ ? ? ? ?* between SM1EN and SM1 is for switching time + the ramp
+ ? ? ? ?* up of the voltage to the CPU (VDD_CPU from PMU).
+ ? ? ? ?*/
+ ? ? ? udelay(3750);
+}
+
+static void reset_A9_cpu(int reset)
+{
+ ? ? ? struct clk_rst_ctlr *clkrst = (struct clk_rst_ctlr

*)NV_PA_CLK_RST_BASE;
+ ? ? ? u32 reg, cpu;
+
+ ? ? ? /*
+ ? ? ? * NOTE: ?Regardless of whether the request is to hold the CPU in reset
+ ? ? ? * ? ? ? ?or take it out of reset, every processor in the CPU complex
+ ? ? ? * ? ? ? ?except the master (CPU 0) will be held in reset because the
+ ? ? ? * ? ? ? ?AVP only talks to the master. The AVP does not know that there
+ ? ? ? * ? ? ? ?are multiple processors in the CPU complex.
+ ? ? ? */

arch/arm/cpu/armv7/tegra2/ap20.c new file +28 -0

+
+ ? ? ? /* Hold CPU 1 in reset */
+ ? ? ? cpu = SET_DBGRESET1 | SET_DERESET1 | SET_CPURESET1;
+ ? ? ? writel(cpu,&clkrst->crc_cpu_cmplx_set);
+
+ ? ? ? reg = readl(&clkrst->crc_rst_dev_l);
+ ? ? ? if (reset) {
+ ? ? ? ? ? ? ? /* Now place CPU0 into reset */
+ ? ? ? ? ? ? ? cpu |= SET_DBGRESET0 | SET_DERESET0 | SET_CPURESET0;
+ ? ? ? ? ? ? ? writel(cpu,&clkrst->crc_cpu_cmplx_set);
+
+ ? ? ? ? ? ? ? /* Enable master CPU reset */
+ ? ? ? ? ? ? ? reg |= SWR_CPU_RST;
+ ? ? ? } else {
+ ? ? ? ? ? ? ? /* Take CPU0 out of reset */
+ ? ? ? ? ? ? ? cpu = CLR_DBGRESET0 | CLR_DERESET0 | CLR_CPURESET0;
+ ? ? ? ? ? ? ? writel(cpu,&clkrst->crc_cpu_cmplx_clr);
+
+ ? ? ? ? ? ? ? /* Disable master CPU reset */
+ ? ? ? ? ? ? ? reg&= ~SWR_CPU_RST;
+ ? ? ? }
+
+ ? ? ? writel(reg,&clkrst->crc_rst_dev_l);
+}
+
+static void clock_enable_coresight(int enable)
+{
+ ? ? ? struct clk_rst_ctlr *clkrst = (struct clk_rst_ctlr

*)NV_PA_CLK_RST_BASE;
+ ? ? ? u32 rst, clk, src;

arch/arm/cpu/armv7/tegra2/ap20.c new file +18 -0

+
+ ? ? ? rst = readl(&clkrst->crc_rst_dev_u);
+ ? ? ? clk = readl(&clkrst->crc_clk_out_enb_u);
+
+ ? ? ? if (enable) {
+ ? ? ? ? ? ? ? rst&= ~SWR_CSITE_RST;
+ ? ? ? ? ? ? ? clk |= CLK_ENB_CSITE;
+ ? ? ? } else {
+ ? ? ? ? ? ? ? rst |= SWR_CSITE_RST;
+ ? ? ? ? ? ? ? clk&= ~CLK_ENB_CSITE;
+ ? ? ? }
+
+ ? ? ? writel(clk,&clkrst->crc_clk_out_enb_u);
+ ? ? ? writel(rst,&clkrst->crc_rst_dev_u);
+
+ ? ? ? if (enable) {
+ ? ? ? ? ? ? ? /*
+ ? ? ? ? ? ? ? ?* Put CoreSight on PLLP_OUT0 (216 MHz) and divide it down

by
+ ? ? ? ? ? ? ? ?* ?1.5, giving an effective frequency of 144MHz.
+ ? ? ? ? ? ? ? ?* Set PLLP_OUT0 [bits31:30 = 00], and use a 7.1 divisor
+ ? ? ? ? ? ? ? ?* ?(bits 7:0), so 00000001b == 1.5 (n+1 + .5)
+ ? ? ? ? ? ? ? ?*/
+ ? ? ? ? ? ? ? src = CLK_DIVIDER(NVBL_PLLP_KHZ, 144000);
+ ? ? ? ? ? ? ? writel(src,&clkrst->crc_clk_src_csite);

arch/arm/cpu/armv7/tegra2/ap20.c new file +31 -0

+
+ ? ? ? ? ? ? ? /* Unlock the CPU CoreSight interfaces */
+ ? ? ? ? ? ? ? rst = 0xC5ACCE55;
+ ? ? ? ? ? ? ? writel(rst, CSITE_CPU_DBG0_LAR);
+ ? ? ? ? ? ? ? writel(rst, CSITE_CPU_DBG1_LAR);
+ ? ? ? }
+}
+
+void start_cpu(u32 reset_vector)
+{
+ ? ? ? /* Enable VDD_CPU */
+ ? ? ? enable_cpu_power_rail();
+
+ ? ? ? /* Hold the CPUs in reset */
+ ? ? ? reset_A9_cpu(1);
+
+ ? ? ? /* Disable the CPU clock */
+ ? ? ? enable_cpu_clock(0);
+
+ ? ? ? /* Enable CoreSight */
+ ? ? ? clock_enable_coresight(1);
+
+ ? ? ? /*
+ ? ? ? ?* Set the entry point for CPU execution from reset,
+ ? ? ? ?* ?if it's a non-zero value.
+ ? ? ? ?*/
+ ? ? ? if (reset_vector)
+ ? ? ? ? ? ? ? writel(reset_vector, EXCEP_VECTOR_CPU_RESET_VECTOR);
+
+ ? ? ? /* Enable the CPU clock */
+ ? ? ? enable_cpu_clock(1);

Quoted 4 lines

+
+ ? ? ? /* If the CPU doesn't already have power, power it up */
+ ? ? ? if (!is_cpu_powered())
+ ? ? ? ? ? ? ? powerup_cpu();

For my education (I don't know Tegra2) haven't the AVP already enabled the CPU power rail and waited 3.75 ms for it to come up? If so, what could prevent the CPU from being powered now?

arch/arm/cpu/armv7/tegra2/ap20.c

Quoted 13 lines

+ ? ? ? /* Take the CPU out of reset */
+ ? ? ? reset_A9_cpu(0);

arch/arm/cpu/armv7/tegra2/ap20.c new file +10 -0

+}
+
+
+void halt_avp(void)
+{
+ ? ? ? for (;;) {
+ ? ? ? ? ? ? ? writel((HALT_COP_EVENT_JTAG | HALT_COP_EVENT_IRQ_1 \
+ ? ? ? ? ? ? ? ? ? ? ? | HALT_COP_EVENT_FIQ_1 | (FLOW_MODE_STOP<<29)),
+ ? ? ? ? ? ? ? ? ? ? ? FLOW_CTLR_HALT_COP_EVENTS);
+ ? ? ? }

Must the write be repeated indefinitely? Can it not be done once then followed by an empty for(;;) ?

Amicalement,
--
Albert.

Quoted 6 lines

arch/arm/cpu/armv7/tegra2/ap20.c line 115

Quoted 4 lines

arch/arm/cpu/armv7/tegra2/ap20.c new file +4 -0

+
+               /* Wait for the power to come up */
+               while (!is_cpu_powered())
+                       ;                       /* Do nothing */

What if power never comes up?

Then the system is hung. I can put a printf here, if you'd like.

Quoted 134 lines

Quoted 134 lines

arch/arm/cpu/armv7/tegra2/ap20.c new file +3 -0

+               /*
+                * Remove the I/O clamps from CPU power partition.
+                * Recommended only on a Warm boot, if the CPU partition

gets
+ * power gated. Shouldn't cause any harm when called after
a

arch/arm/cpu/armv7/tegra2/ap20.c new file +27 -0

+                * cold boot according to HW, probably just redundant.
+                */
+               remove_cpu_io_clamps();
+       }
+}
+
+static void enable_cpu_power_rail(void)
+{
+       struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
+       u32 reg;
+
+       reg = readl(&pmc->pmc_cntrl);
+       reg |= CPUPWRREQ_OE;
+       writel(reg,&pmc->pmc_cntrl);
+
+       /*
+        * The TI PMU65861C needs a 3.75ms delay between enabling
+        * the power rail and enabling the CPU clock.  This delay
+        * between SM1EN and SM1 is for switching time + the ramp
+        * up of the voltage to the CPU (VDD_CPU from PMU).
+        */
+       udelay(3750);
+}
+
+static void reset_A9_cpu(int reset)
+{
+       struct clk_rst_ctlr *clkrst = (struct clk_rst_ctlr

*)NV_PA_CLK_RST_BASE;

arch/arm/cpu/armv7/tegra2/ap20.c new file +4 -0

+       u32 reg, cpu;
+
+       /*
+       * NOTE:  Regardless of whether the request is to hold the CPU in

reset
+ * or take it out of reset, every processor in the CPU
complex
+ * except the master (CPU 0) will be held in reset because
the
+ * AVP only talks to the master. The AVP does not know that
there

arch/arm/cpu/armv7/tegra2/ap20.c new file +30 -0

+       *        are multiple processors in the CPU complex.
+       */
+
+       /* Hold CPU 1 in reset */
+       cpu = SET_DBGRESET1 | SET_DERESET1 | SET_CPURESET1;
+       writel(cpu,&clkrst->crc_cpu_cmplx_set);
+
+       reg = readl(&clkrst->crc_rst_dev_l);
+       if (reset) {
+               /* Now place CPU0 into reset */
+               cpu |= SET_DBGRESET0 | SET_DERESET0 | SET_CPURESET0;
+               writel(cpu,&clkrst->crc_cpu_cmplx_set);
+
+               /* Enable master CPU reset */
+               reg |= SWR_CPU_RST;
+       } else {
+               /* Take CPU0 out of reset */
+               cpu = CLR_DBGRESET0 | CLR_DERESET0 | CLR_CPURESET0;
+               writel(cpu,&clkrst->crc_cpu_cmplx_clr);
+
+               /* Disable master CPU reset */
+               reg&= ~SWR_CPU_RST;
+       }
+
+       writel(reg,&clkrst->crc_rst_dev_l);
+}
+
+static void clock_enable_coresight(int enable)
+{
+       struct clk_rst_ctlr *clkrst = (struct clk_rst_ctlr

*)NV_PA_CLK_RST_BASE;

arch/arm/cpu/armv7/tegra2/ap20.c new file +19 -0

+       u32 rst, clk, src;
+
+       rst = readl(&clkrst->crc_rst_dev_u);
+       clk = readl(&clkrst->crc_clk_out_enb_u);
+
+       if (enable) {
+               rst&= ~SWR_CSITE_RST;
+               clk |= CLK_ENB_CSITE;
+       } else {
+               rst |= SWR_CSITE_RST;
+               clk&= ~CLK_ENB_CSITE;
+       }
+
+       writel(clk,&clkrst->crc_clk_out_enb_u);
+       writel(rst,&clkrst->crc_rst_dev_u);
+
+       if (enable) {
+               /*
+                * Put CoreSight on PLLP_OUT0 (216 MHz) and divide it down

by

arch/arm/cpu/armv7/tegra2/ap20.c new file +37 -0

+                *  1.5, giving an effective frequency of 144MHz.
+                * Set PLLP_OUT0 [bits31:30 = 00], and use a 7.1 divisor
+                *  (bits 7:0), so 00000001b == 1.5 (n+1 + .5)
+                */
+               src = CLK_DIVIDER(NVBL_PLLP_KHZ, 144000);
+               writel(src,&clkrst->crc_clk_src_csite);
+
+               /* Unlock the CPU CoreSight interfaces */
+               rst = 0xC5ACCE55;
+               writel(rst, CSITE_CPU_DBG0_LAR);
+               writel(rst, CSITE_CPU_DBG1_LAR);
+       }
+}
+
+void start_cpu(u32 reset_vector)
+{
+       /* Enable VDD_CPU */
+       enable_cpu_power_rail();
+
+       /* Hold the CPUs in reset */
+       reset_A9_cpu(1);
+
+       /* Disable the CPU clock */
+       enable_cpu_clock(0);
+
+       /* Enable CoreSight */
+       clock_enable_coresight(1);
+
+       /*
+        * Set the entry point for CPU execution from reset,
+        *  if it's a non-zero value.
+        */
+       if (reset_vector)
+               writel(reset_vector, EXCEP_VECTOR_CPU_RESET_VECTOR);
+
+       /* Enable the CPU clock */
+       enable_cpu_clock(1);

Quoted 8 lines

arch/arm/cpu/armv7/tegra2/ap20.c line 244

Quoted 4 lines

arch/arm/cpu/armv7/tegra2/ap20.c new file +4 -0

+
+       /* If the CPU doesn't already have power, power it up */
+       if (!is_cpu_powered())
+               powerup_cpu();

For my education (I don't know Tegra2) haven't the AVP already enabled the CPU power rail and waited 3.75 ms for it to come up? If so, what could prevent the CPU from being powered now?

True, this is just an additional check that was in the code I ported. I'll remove it as redundant.

Quoted 16 lines

arch/arm/cpu/armv7/tegra2/ap20.c line 257

Quoted 13 lines

arch/arm/cpu/armv7/tegra2/ap20.c new file +12 -0

+       /* Take the CPU out of reset */
+       reset_A9_cpu(0);
+}
+
+
+void halt_avp(void)
+{
+       for (;;) {
+               writel((HALT_COP_EVENT_JTAG | HALT_COP_EVENT_IRQ_1 \
+                       | HALT_COP_EVENT_FIQ_1 | (FLOW_MODE_STOP<<29)),
+                       FLOW_CTLR_HALT_COP_EVENTS);
+       }

Must the write be repeated indefinitely? Can it not be done once then followed by an empty for(;;) ?

IIRC, there was an additional infinite for (;;) in previous code, but that was removed to satisfy a reviewer.

I can change it if you insist, but I don't know if it's written this way (ported from legacy bootloader) on purpose, i.e. to keep the AVP from spontaneously waking up and executing code from SRAM, etc. If it's not a deal-breaker, I'd prefer to leave it as-is.

Hi Tom,

Le 13/04/2011 22:21, Tom Warren a ?crit :

Quoted 5 lines

Quoted 5 lines

Quoted 4 lines

+
+ ? ? ? ? ? ? ? /* Wait for the power to come up */
+ ? ? ? ? ? ? ? while (!is_cpu_powered())
+ ? ? ? ? ? ? ? ? ? ? ? ; ? ? ? ? ? ? ? ? ? ? ? /* Do nothing */

Quoted 3 lines

Quoted 1 line

What if power never comes up?

Then the system is hung. I can put a printf here, if you'd like.

Is the system hung? Can it really not proceed to the prompt? Anyway, at least, yes, a printf would be welcome.

Quoted 167 lines

Quoted 138 lines

Quoted 138 lines

+ ? ? ? ? ? ? ? /*
+ ? ? ? ? ? ? ? ?* Remove the I/O clamps from CPU power partition.
+ ? ? ? ? ? ? ? ?* Recommended only on a Warm boot, if the CPU partition gets
+ ? ? ? ? ? ? ? ?* power gated. Shouldn't cause any harm when called after
a
+ ? ? ? ? ? ? ? ?* cold boot according to HW, probably just redundant.
+ ? ? ? ? ? ? ? ?*/
+ ? ? ? ? ? ? ? remove_cpu_io_clamps();
+ ? ? ? }

(quoted diff) +23 -0

+}
+
+static void enable_cpu_power_rail(void)
+{
+ ? ? ? struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE;
+ ? ? ? u32 reg;
+
+ ? ? ? reg = readl(&pmc->pmc_cntrl);
+ ? ? ? reg |= CPUPWRREQ_OE;
+ ? ? ? writel(reg,&pmc->pmc_cntrl);
+
+ ? ? ? /*
+ ? ? ? ?* The TI PMU65861C needs a 3.75ms delay between enabling
+ ? ? ? ?* the power rail and enabling the CPU clock. ?This delay
+ ? ? ? ?* between SM1EN and SM1 is for switching time + the ramp
+ ? ? ? ?* up of the voltage to the CPU (VDD_CPU from PMU).
+ ? ? ? ?*/
+ ? ? ? udelay(3750);
+}
+
+static void reset_A9_cpu(int reset)
+{
+ ? ? ? struct clk_rst_ctlr *clkrst = (struct clk_rst_ctlr

*)NV_PA_CLK_RST_BASE;
+ ? ? ? u32 reg, cpu;
+
+ ? ? ? /*
+ ? ? ? * NOTE: ?Regardless of whether the request is to hold the CPU in reset
+ ? ? ? * ? ? ? ?or take it out of reset, every processor in the CPU complex
+ ? ? ? * ? ? ? ?except the master (CPU 0) will be held in reset because the
+ ? ? ? * ? ? ? ?AVP only talks to the master. The AVP does not know that
there
+ ? ? ? * ? ? ? ?are multiple processors in the CPU complex.
+ ? ? ? */

(quoted diff) +28 -0

+
+ ? ? ? /* Hold CPU 1 in reset */
+ ? ? ? cpu = SET_DBGRESET1 | SET_DERESET1 | SET_CPURESET1;
+ ? ? ? writel(cpu,&clkrst->crc_cpu_cmplx_set);
+
+ ? ? ? reg = readl(&clkrst->crc_rst_dev_l);
+ ? ? ? if (reset) {
+ ? ? ? ? ? ? ? /* Now place CPU0 into reset */
+ ? ? ? ? ? ? ? cpu |= SET_DBGRESET0 | SET_DERESET0 | SET_CPURESET0;
+ ? ? ? ? ? ? ? writel(cpu,&clkrst->crc_cpu_cmplx_set);
+
+ ? ? ? ? ? ? ? /* Enable master CPU reset */
+ ? ? ? ? ? ? ? reg |= SWR_CPU_RST;
+ ? ? ? } else {
+ ? ? ? ? ? ? ? /* Take CPU0 out of reset */
+ ? ? ? ? ? ? ? cpu = CLR_DBGRESET0 | CLR_DERESET0 | CLR_CPURESET0;
+ ? ? ? ? ? ? ? writel(cpu,&clkrst->crc_cpu_cmplx_clr);
+
+ ? ? ? ? ? ? ? /* Disable master CPU reset */
+ ? ? ? ? ? ? ? reg&= ~SWR_CPU_RST;
+ ? ? ? }
+
+ ? ? ? writel(reg,&clkrst->crc_rst_dev_l);
+}
+
+static void clock_enable_coresight(int enable)
+{
+ ? ? ? struct clk_rst_ctlr *clkrst = (struct clk_rst_ctlr

*)NV_PA_CLK_RST_BASE;
+ ? ? ? u32 rst, clk, src;

(quoted diff) +18 -0

+
+ ? ? ? rst = readl(&clkrst->crc_rst_dev_u);
+ ? ? ? clk = readl(&clkrst->crc_clk_out_enb_u);
+
+ ? ? ? if (enable) {
+ ? ? ? ? ? ? ? rst&= ~SWR_CSITE_RST;
+ ? ? ? ? ? ? ? clk |= CLK_ENB_CSITE;
+ ? ? ? } else {
+ ? ? ? ? ? ? ? rst |= SWR_CSITE_RST;
+ ? ? ? ? ? ? ? clk&= ~CLK_ENB_CSITE;
+ ? ? ? }
+
+ ? ? ? writel(clk,&clkrst->crc_clk_out_enb_u);
+ ? ? ? writel(rst,&clkrst->crc_rst_dev_u);
+
+ ? ? ? if (enable) {
+ ? ? ? ? ? ? ? /*
+ ? ? ? ? ? ? ? ?* Put CoreSight on PLLP_OUT0 (216 MHz) and divide it

down
by
+ ? ? ? ? ? ? ? ?* ?1.5, giving an effective frequency of 144MHz.
+ ? ? ? ? ? ? ? ?* Set PLLP_OUT0 [bits31:30 = 00], and use a 7.1 divisor
+ ? ? ? ? ? ? ? ?* ?(bits 7:0), so 00000001b == 1.5 (n+1 + .5)
+ ? ? ? ? ? ? ? ?*/
+ ? ? ? ? ? ? ? src = CLK_DIVIDER(NVBL_PLLP_KHZ, 144000);
+ ? ? ? ? ? ? ? writel(src,&clkrst->crc_clk_src_csite);

(quoted diff) +31 -0

+
+ ? ? ? ? ? ? ? /* Unlock the CPU CoreSight interfaces */
+ ? ? ? ? ? ? ? rst = 0xC5ACCE55;
+ ? ? ? ? ? ? ? writel(rst, CSITE_CPU_DBG0_LAR);
+ ? ? ? ? ? ? ? writel(rst, CSITE_CPU_DBG1_LAR);
+ ? ? ? }
+}
+
+void start_cpu(u32 reset_vector)
+{
+ ? ? ? /* Enable VDD_CPU */
+ ? ? ? enable_cpu_power_rail();
+
+ ? ? ? /* Hold the CPUs in reset */
+ ? ? ? reset_A9_cpu(1);
+
+ ? ? ? /* Disable the CPU clock */
+ ? ? ? enable_cpu_clock(0);
+
+ ? ? ? /* Enable CoreSight */
+ ? ? ? clock_enable_coresight(1);
+
+ ? ? ? /*
+ ? ? ? ?* Set the entry point for CPU execution from reset,
+ ? ? ? ?* ?if it's a non-zero value.
+ ? ? ? ?*/
+ ? ? ? if (reset_vector)
+ ? ? ? ? ? ? ? writel(reset_vector, EXCEP_VECTOR_CPU_RESET_VECTOR);
+
+ ? ? ? /* Enable the CPU clock */
+ ? ? ? enable_cpu_clock(1);

Quoted 8 lines

Quoted 4 lines

+
+ ? ? ? /* If the CPU doesn't already have power, power it up */
+ ? ? ? if (!is_cpu_powered())
+ ? ? ? ? ? ? ? powerup_cpu();

For my education (I don't know Tegra2) haven't the AVP already enabled the CPU power rail and waited 3.75 ms for it to come up? If so, what could prevent the CPU from being powered now?

True, this is just an additional check that was in the code I ported. I'll remove it as redundant.

Quoted 16 lines

arch/arm/cpu/armv7/tegra2/ap20.c

Quoted 13 lines

+ ? ? ? /* Take the CPU out of reset */
+ ? ? ? reset_A9_cpu(0);

arch/arm/cpu/armv7/tegra2/ap20.c new file +10 -0

+}
+
+
+void halt_avp(void)
+{
+ ? ? ? for (;;) {
+ ? ? ? ? ? ? ? writel((HALT_COP_EVENT_JTAG | HALT_COP_EVENT_IRQ_1 \
+ ? ? ? ? ? ? ? ? ? ? ? | HALT_COP_EVENT_FIQ_1 | (FLOW_MODE_STOP<<29)),
+ ? ? ? ? ? ? ? ? ? ? ? FLOW_CTLR_HALT_COP_EVENTS);
+ ? ? ? }

Must the write be repeated indefinitely? Can it not be done once then followed by an empty for(;;) ?

Quoted 2 lines

IIRC, there was an additional infinite for (;;) in previous code, but that was removed to satisfy a reviewer.

:)

Quoted 4 lines

I can change it if you insist, but I don't know if it's written this way (ported from legacy bootloader) on purpose, i.e. to keep the AVP from spontaneously waking up and executing code from SRAM, etc. ?If it's not a deal-breaker, I'd prefer to leave it as-is.

That's ok, leave it as it is.

Amicalement,
--
Albert.