README.arm-relocation: debugging options update
v3 cover README.arm-relocation: debugging options update
As Wolfgang pointed out, bdinfo can be used to get the relocation address so update the README to indicate that this can be done instead of suggesting that u-boot get rebuilt with debugging enabled.
Since gd is always addressable, descibe also a method whereby the relocation address is obtained from a it using gdb.
Ben Gardiner (2):
README.arm-relocation: get relocated address from bdinfo README.arm-relocation: get relocated address in gdb
doc/README.arm-relocation | 61 ++++++++++++++++++++++----------------------- 1 files changed, 30 insertions(+), 31 deletions(-)
PATCH v3 1/2 README.arm-relocation: get relocated address from bdinfo
The bdinfo command prints the relocaddr on ARM as it does on PPC.
Update the debugging instructions for arm relocation to reflect this fact rather than requiring that the user rebuild the u-boot image using -DDEBUG.
---
Changes since V1: none; introduced in V2
doc/README.arm-relocation | 53 ++++++++++++++++++-------------------------- 1 files changed, 22 insertions(+), 31 deletions(-)
doc/README.arm-relocation +22 -31
@@ -106,13 +106,9 @@ TBC Debugging u-boot in RAM: (example on the qong board) -a) add in config.mk: - -PLATFORM_CPPFLAGS += -DDEBUG - ----------------- -b) start debugger +a) start debugger arm-linux-gdb u-boot
@@ -130,7 +126,7 @@ The target architecture is set automatically (currently arm) ----------------- -c) connect to target +b) connect to target target remote bdi10:2001
@@ -141,7 +137,7 @@ Remote debugging using bdi10:2001 ----------------- -d) discard symbol-file +c) discard symbol-file (gdb) symbol-file Discard symbol table from `/home/hs/celf/u-boot/u-boot'? (y or n) y
@@ -150,7 +146,7 @@ No symbol file now. ----------------- -e) load new symbol table: +d) load new symbol table: (gdb) add-symbol-file u-boot 0x8ff08000 add symbol table from file "u-boot" at
@@ -167,28 +163,23 @@ Program received signal SIGSTOP, Stopped (signal). add-symbol-file u-boot 0x8ff08000 ^^^^^^^^^^ - get this address from u-boot debug printfs - -U-Boot 2010.06-rc2-00009-gf77b8b8-dirty (Jun 22 2010 - 09:43:46) - -U-Boot code: A0000000 -> A0058BAC BSS: -> A0061F10 -CPU: Freescale i.MX31 at 398 MHz -Board: DAVE/DENX Qong -mon: FFFFFFFF gd->monLen: 00061F10 -Top of RAM usable for U-Boot at: 90000000 -LCD panel info: 640 x 480, 16 bit/pix -Reserving 600k for LCD Framebuffer at: 8ff6a000 -Reserving 391k for U-Boot at: 8ff08000 - ^^^^^^^^ -Reserving 1280k for malloc() at: 8fdc8000 -Reserving 24 Bytes for Board Info at: 8fdc7fe8 -Reserving 52 Bytes for Global Data at: 8fdc7fb4 -New Stack Pointer is: 8fdc7fb0 -RAM Configuration: -Bank #0: 80000000 256 MiB -relocation Offset is: eff08000 -mon: 00058BAC gd->monLen: 00061F10 -Now running in RAM - U-Boot at: 8ff08000 - ^^^^^^^^ + get this address from u-boot bdinfo command + + => bdinfo +rch_number = XXXXXXXXXX +boot_params = XXXXXXXXXX +DRAM bank = XXXXXXXXXX +-> start = XXXXXXXXXX +-> size = XXXXXXXXXX +ethaddr = XXXXXXXXXX +ip_addr = XXXXXXXXXX +baudrate = XXXXXXXXXX +TLB addr = XXXXXXXXXX +relocaddr = 0x8ff08000 + ^^^^^^^^^^ +reloc off = XXXXXXXXXX +irq_sp = XXXXXXXXXX +sp start = XXXXXXXXXX +FB base = XXXXXXXXXX Now you can use gdb as usual :-)
Signature · 1 line
1.7.1
PATCH v3 1/2 README.arm-relocation: get relocated address from bdinfo
Hello Ben,
Quoted 10 lines · Ben Gardiner
The bdinfo command prints the relocaddr on ARM as it does on PPC.
Update the debugging instructions for arm relocation to reflect this fact rather than requiring that the user rebuild the u-boot image using -DDEBUG.
Signed-off-by Ben Gardiner <[email protected]>CC Wolfgang Denk <[email protected]>
Quoted 6 lines
---
Changes since V1: none; introduced in V2
doc/README.arm-relocation | 53 ++++++++++++++++++-------------------------- 1 files changed, 22 insertions(+), 31 deletions(-)
bye,
Heiko
Signature · 2 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Wolfgang Denk
AppliedPATCH v3 1/2 README.arm-relocation: get relocated address from bdinfo
In reply to Ben GardinerDear Ben Gardiner,
Quoted 10 lines · In message <787a04417ee0eb01c6eb3a7a1edff7ee9a8f825e.1304024417.git.bengardiner…
The bdinfo command prints the relocaddr on ARM as it does on PPC.
Update the debugging instructions for arm relocation to reflect this fact rather than requiring that the user rebuild the u-boot image using -DDEBUG.
Signed-off-by Ben Gardiner <[email protected]>CC Wolfgang Denk <[email protected]>
Quoted 6 lines
---
Changes since V1: none; introduced in V2
doc/README.arm-relocation | 53 ++++++++++++++++++-------------------------- 1 files changed, 22 insertions(+), 31 deletions(-)
Applied, thanks.
Best regards,
Wolfgang Denk
Signature · 4 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de "In matrimony, to hesitate is sometimes to be saved." - Butler
PATCH v3 2/2 README.arm-relocation: get relocated address in gdb
In reply to Ben GardinerWhen your emulator is connected at reset (or is used to load u-boot) it is possible to get the relocation address from the gd->relocaddr since gd is always in r8 (on ARM) it is addressable before the gdb has remapped symbols.
Document this alternate method in-line with the original method written by Heiko Schocher.
---
Changes since V2:
* add gd->relocaddr as a secondary method of obtaining the symbol-file gdb argument
Changes since V1:
* update to reflect proposed changes to existing debug instructions:
renumber steps, remove note about -DDEBUG
--- doc/README.arm-relocation | 8 ++++++++ 1 files changed, 8 insertions(+), 0 deletions(-)
doc/README.arm-relocation +8 -0
@@ -164,6 +164,7 @@ Program received signal SIGSTOP, Stopped (signal). add-symbol-file u-boot 0x8ff08000 ^^^^^^^^^^ get this address from u-boot bdinfo command + or get it from gd->relocaddr in gdb => bdinfo rch_number = XXXXXXXXXX
@@ -182,4 +183,11 @@ irq_sp = XXXXXXXXXX sp start = XXXXXXXXXX FB base = XXXXXXXXXX +or interrupt execution by any means and re-load the symbols at the location +specified by gd->relocaddr -- this is only valid after board_init_f. + +(gdb) set $s = gd->relocaddr +(gdb) symbol-file +(gdb) add-symbol-file u-boot $s + Now you can use gdb as usual :-)
Signature · 1 line
1.7.1
PATCH v3 2/2 README.arm-relocation: get relocated address in gdb
Hello Ben,
Quoted 19 lines · Ben Gardiner
When your emulator is connected at reset (or is used to load u-boot) it is possible to get the relocation address from the
gd->relocaddrsince gd is always in r8 (on ARM) it is addressable before the gdb has remapped symbols.Document this alternate method in-line with the original method written by Heiko Schocher.
Signed-off-by Ben Gardiner <[email protected]>CC Heiko Schocher <[email protected]>CC Wolfgang Denk <[email protected]>---
Changes since V2:
* addgd->relocaddras a secondary method of obtaining the symbol-file gdb argument
Changes since V1:
* update to reflect proposed changes to existing debug instructions:
renumber steps, remove note about -DDEBUG
Quoted 3 lines
--- doc/README.arm-relocation | 8 ++++++++ 1 files changed, 8 insertions(+), 0 deletions(-)
Thanks!
bye,
Heiko
Signature · 2 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Wolfgang Denk
AppliedPATCH v3 2/2 README.arm-relocation: get relocated address in gdb
In reply to Ben GardinerDear Ben Gardiner,
Quoted 19 lines · In message <7ed11e02b0db005231f5c6baa299761f3aa04f6f.1304024417.git.bengardiner…
When your emulator is connected at reset (or is used to load u-boot) it is possible to get the relocation address from the
gd->relocaddrsince gd is always in r8 (on ARM) it is addressable before the gdb has remapped symbols.Document this alternate method in-line with the original method written by Heiko Schocher.
Signed-off-by Ben Gardiner <[email protected]>CC Heiko Schocher <[email protected]>CC Wolfgang Denk <[email protected]>---
Changes since V2:
* addgd->relocaddras a secondary method of obtaining the symbol-file gdb argument
Changes since V1:
* update to reflect proposed changes to existing debug instructions:
renumber steps, remove note about -DDEBUG
Quoted 3 lines
--- doc/README.arm-relocation | 8 ++++++++ 1 files changed, 8 insertions(+), 0 deletions(-)
Applied, thanks.
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Military secrets are the most fleeting of all. -- Spock, "The Enterprise Incident", stardate 5027.4