MX53: support for freescale MX53LOCO board
PATCH v7 1/1 MX53: support for freescale MX53LOCO board
This patch add initial support for freescale MX53LOCO board. Network(FEC),SD/MMC,UART have been supported by this patch
---
Changes since v6:
- move the pmic support out from this patchset Changes since v5:
- merge the "Add power init support" patch
changes since v4:
- remove the boot reset cause from board support changes since v3:
- include other two small patch into this commit,
mx53loco: set mmc env to MMC slot1
MX5: Enable flat-device-tree support on mx53 loco board changes since V2:
-factor out the boot cause function to common code, -fix gd->ram_size with full memory size
-remove the '1' from all #defines that just enable features -correct memory test end address value
--- MAINTAINERS | 1 + board/freescale/mx53loco/Makefile | 47 +++++ board/freescale/mx53loco/imximage.cfg | 96 +++++++++++ board/freescale/mx53loco/mx53loco.c | 302 +++++++++++++++++++++++++++++++++ boards.cfg | 1 + include/configs/mx53loco.h | 186 ++++++++++++++++++++ 6 files changed, 633 insertions(+), 0 deletions(-)
MAINTAINERS +1 -0
@@ -574,6 +574,7 @@ Stefano Babic <[email protected]> Jason Liu <[email protected]> mx53evk i.MX53 + mx53loco i.MX53 Enric Balletbo i Serra <[email protected]>
board/freescale/mx53loco/Makefile new file +47 -0
47 lines not on this page · raw message
board/freescale/mx53loco/imximage.cfg new file +96 -0
96 lines not on this page · raw message
board/freescale/mx53loco/mx53loco.c new file +302 -0
302 lines not on this page · raw message
boards.cfg +1 -0
@@ -124,6 +124,7 @@ ca9x4_ct_vxp arm armv7 vexpress armltd efikamx arm armv7 efikamx - mx5 mx51evk arm armv7 mx51evk freescale mx5 mx51evk:IMX_CONFIG=board/freescale/mx51evk/imximage.cfg mx53evk arm armv7 mx53evk freescale mx5 mx53evk:IMX_CONFIG=board/freescale/mx53evk/imximage.cfg +mx53loco arm armv7 mx53loco freescale mx5 mx53loco:IMX_CONFIG=board/freescale/mx53loco/imximage.cfg vision2 arm armv7 vision2 ttcontrol mx5 cm_t35 arm armv7 cm_t35 - omap3 omap3_overo arm armv7 overo - omap3
include/configs/mx53loco.h new file +186 -0
186 lines not on this page · raw message
Signature · 1 line
1.7.1
PATCH v7 1/1 MX53: support for freescale MX53LOCO board
Quoted 4 lines · Jason Liu
This patch add initial support for freescale MX53LOCO board. Network(FEC),SD/MMC,UART have been supported by this patch
Signed-off-by Jason Liu <[email protected]>
Applied to u-boot-imx, thanks.
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de =====================================================================