integratorap: support relocation
PATCH v3 3/9 integratorap: support relocation
The integrator board was apparently never converted over to support relocation until now. After this the integrator u-boot both compiles and boots on the Integrator AP.
--- board/armltd/integrator/integrator.c | 14 ++++++++------ 1 files changed, 8 insertions(+), 6 deletions(-)
board/armltd/integrator/integrator.c +8 -6
@@ -86,14 +86,16 @@ int misc_init_r (void)return (0 ); } -/****************************** -Routine: -Description: -******************************/ -int dram_init (void ) +void dram_init_banksize (void ) { gd->bd->bi_dram[0 ].start =PHYS_SDRAM_1 ; - gd->bd->bi_dram[0 ].size =PHYS_SDRAM_1_SIZE ; + gd->bd->bi_dram[0 ].size =PHYS_SDRAM_1_SIZE ; +} + +int dram_init (void ) +{ + gd->ram_size =get_ram_size ((long *)CONFIG_SYS_SDRAM_BASE , +PHYS_SDRAM_1_SIZE );#ifdef CONFIG_CM_SPD_DETECT {
Signature · 1 line
1.7.6
PATCH v3 3/9 integratorap: support relocation
Hello.
Quoted 17 lines · Linus Walleij
The integrator board was apparently never converted over to support relocation until now. After this the integrator u-boot both compiles and boots on the Integrator AP.
Signed-off-by Linus Walleij<[email protected]>--- board/armltd/integrator/integrator.c | 14 ++++++++------ 1 files changed, 8 insertions(+), 6 deletions(-)board/armltd/integrator/integrator.c +0
-0@@ -86,14 +86,16 @@ int misc_init_r (void)return (0 ); }
board/armltd/integrator/integrator.c int misc_init_r (void) · line 92
Quoted 10 lines
board/armltd/integrator/integrator.c +2
-6-/****************************** -Routine: -Description: -******************************/ -int dram_init (void ) +void dram_init_banksize (void ) { gd->bd->bi_dram[0 ].start =PHYS_SDRAM_1 ; - gd->bd->bi_dram[0 ].size =PHYS_SDRAM_1_SIZE ; + gd->bd->bi_dram[0 ].size =PHYS_SDRAM_1_SIZE ;
You're using spaces instead of tab here...
WBR, Sergei
PATCH v3 3/9 integratorap: support relocation
Quoted 8 lines · Sergei Shtylyov
Quoted 6 lines
board/armltd/integrator/integrator.c +1
-1-int dram_init (void ) +void dram_init_banksize (void )?{
? ? ? ?gd->bd->bi_dram[0].start =PHYS_SDRAM_1;
- ? ? ? gd->bd->bi_dram[0].size ?=PHYS_SDRAM_1_SIZE;
+ ? ? ? ?gd->bd->bi_dram[0].size =PHYS_SDRAM_1_SIZE;? You're using spaces instead of tab here...
Oh man. I'll fix up. I re-ran all patches through checkpatch and this one seems to be the only one remaining with the problem, luckily.
Linus Walleij
PATCH v3 3/9 integratorap: support relocation
Quoted 10 lines · Linus Walleij
Quoted 8 lines · Sergei Shtylyov
Quoted 6 lines
board/armltd/integrator/integrator.c +1
-1-int dram_init (void ) +void dram_init_banksize (void )?{
? ? ? ?gd->bd->bi_dram[0].start =PHYS_SDRAM_1;
- ? ? ? gd->bd->bi_dram[0].size ?=PHYS_SDRAM_1_SIZE;
+ ? ? ? ?gd->bd->bi_dram[0].size =PHYS_SDRAM_1_SIZE;? You're using spaces instead of tab here...
Quoted 2 lines
Oh man. I'll fix up. I re-ran all patches through checkpatch and this one seems to be the only one remaining with the problem, luckily.
Or well, patch [6/9] fixes the problem.
It's probably better that I squash patch 3 and 6.
This means the whole series need to be rebased again of course, so I'm resending the whole thing again.
Thanks,
Linus Walleij