Skip to contentSkip to conversation

component device mismatches found: 9600

DISCUSSION Timothy D. Lenz 3 participants 6 messages Jul 31, 2011 – Aug 2, 2011 MD RAID

lore
Share & tools
lore
#0 lore raw

Looking through the logs, I found this in daemon.log.0. Is this a sign of a problem? Below is the entire log:

Jul  3 00:57:01 x64VDR mdadm[2003]: RebuildStarted event detected on md device /dev/md0
Jul  3 00:57:02 x64VDR mdadm[2003]: RebuildStarted event detected on md device /dev/md3
Jul  3 01:02:10 x64VDR mdadm[2003]: RebuildStarted event detected on md device /dev/md1
Jul  3 01:02:10 x64VDR mdadm[2003]: RebuildFinished event detected on md device /dev/md0
Jul  3 01:03:01 x64VDR mdadm[2003]: RebuildStarted event detected on md device /dev/md2
Jul  3 01:03:01 x64VDR mdadm[2003]: RebuildFinished event detected on md device /dev/md1, component device  mismatches found: 9600
Jul  3 01:19:41 x64VDR mdadm[2003]: Rebuild29 event detected on md device /dev/md3
Jul  3 01:19:41 x64VDR mdadm[2003]: Rebuild21 event detected on md device /dev/md2
Jul  3 01:36:21 x64VDR mdadm[2003]: Rebuild50 event detected on md device /dev/md3
Jul  3 01:36:21 x64VDR mdadm[2003]: Rebuild41 event detected on md device /dev/md2
Jul  3 01:53:01 x64VDR mdadm[2003]: Rebuild67 event detected on md device /dev/md3
Jul  3 02:09:41 x64VDR mdadm[2003]: Rebuild83 event detected on md device /dev/md3
Jul  3 02:09:41 x64VDR mdadm[2003]: Rebuild75 event detected on md device /dev/md2
Jul  3 02:26:21 x64VDR mdadm[2003]: Rebuild88 event detected on md device /dev/md2
Jul  3 02:32:20 x64VDR mdadm[2003]: RebuildFinished event detected on md device /dev/md3
Jul  3 02:43:23 x64VDR mdadm[2003]: RebuildFinished event detected on md device /dev/md2
#1 lore raw
Quoted 36 lines · Timothy D. Lenz

Looking through the logs, I found this in daemon.log.0. Is this a sign of a problem? Below is the entire log:

Jul  3 00:57:01 x64VDR mdadm[2003]: RebuildStarted event detected on md device /dev/md0
Jul  3 00:57:02 x64VDR mdadm[2003]: RebuildStarted event detected on md device /dev/md3
Jul  3 01:02:10 x64VDR mdadm[2003]: RebuildStarted event detected on md device /dev/md1
Jul  3 01:02:10 x64VDR mdadm[2003]: RebuildFinished event detected on md device /dev/md0
Jul  3 01:03:01 x64VDR mdadm[2003]: RebuildStarted event detected on md device /dev/md2
Jul  3 01:03:01 x64VDR mdadm[2003]: RebuildFinished event detected on md device /dev/md1, component device  mismatches found: 9600
Jul  3 01:19:41 x64VDR mdadm[2003]: Rebuild29 event detected on md device /dev/md3
Jul  3 01:19:41 x64VDR mdadm[2003]: Rebuild21 event detected on md device /dev/md2
Jul  3 01:36:21 x64VDR mdadm[2003]: Rebuild50 event detected on md device /dev/md3
Jul  3 01:36:21 x64VDR mdadm[2003]: Rebuild41 event detected on md device /dev/md2
Jul  3 01:53:01 x64VDR mdadm[2003]: Rebuild67 event detected on md device /dev/md3
Jul  3 02:09:41 x64VDR mdadm[2003]: Rebuild83 event detected on md device /dev/md3
Jul  3 02:09:41 x64VDR mdadm[2003]: Rebuild75 event detected on md device /dev/md2
Jul  3 02:26:21 x64VDR mdadm[2003]: Rebuild88 event detected on md device /dev/md2
Jul  3 02:32:20 x64VDR mdadm[2003]: RebuildFinished event detected on md device /dev/md3
Jul  3 02:43:23 x64VDR mdadm[2003]: RebuildFinished event detected on md device /dev/md2

Quoted 5 lines

--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Could you post the output of:

smartctl -a /dev/your_hdd (all HDDs used by the arrays) cat /proc/mdstat
mdadm -D /dev/md(your arrays)

/Mathias
--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#2 lore raw
Quoted 43 lines · Mathias Burén
Quoted 34 lines · Timothy D. Lenz

Looking through the logs, I found this in daemon.log.0. Is this a sign of a problem? Below is the entire log:

Jul  3 00:57:01 x64VDR mdadm[2003]: RebuildStarted event detected on md
device /dev/md0
Jul  3 00:57:02 x64VDR mdadm[2003]: RebuildStarted event detected on md
device /dev/md3
Jul  3 01:02:10 x64VDR mdadm[2003]: RebuildStarted event detected on md
device /dev/md1
Jul  3 01:02:10 x64VDR mdadm[2003]: RebuildFinished event detected on md
device /dev/md0
Jul  3 01:03:01 x64VDR mdadm[2003]: RebuildStarted event detected on md
device /dev/md2
Jul  3 01:03:01 x64VDR mdadm[2003]: RebuildFinished event detected on md
device /dev/md1, component device  mismatches found: 9600
Jul  3 01:19:41 x64VDR mdadm[2003]: Rebuild29 event detected on md device
/dev/md3
Jul  3 01:19:41 x64VDR mdadm[2003]: Rebuild21 event detected on md device
/dev/md2
Jul  3 01:36:21 x64VDR mdadm[2003]: Rebuild50 event detected on md device
/dev/md3
Jul  3 01:36:21 x64VDR mdadm[2003]: Rebuild41 event detected on md device
/dev/md2
Jul  3 01:53:01 x64VDR mdadm[2003]: Rebuild67 event detected on md device
/dev/md3
Jul  3 02:09:41 x64VDR mdadm[2003]: Rebuild83 event detected on md device
/dev/md3
Jul  3 02:09:41 x64VDR mdadm[2003]: Rebuild75 event detected on md device
/dev/md2
Jul  3 02:26:21 x64VDR mdadm[2003]: Rebuild88 event detected on md device
/dev/md2
Jul  3 02:32:20 x64VDR mdadm[2003]: RebuildFinished event detected on md
device /dev/md3
Jul  3 02:43:23 x64VDR mdadm[2003]: RebuildFinished event detected on md
Quoted 7 lines

device /dev/md2

--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Quoted 8 lines

Could you post the output of:

smartctl -a /dev/your_hdd (all HDDs used by the arrays) cat /proc/mdstat
mdadm -D /dev/md(your arrays)

/Mathias

Don't think I have smartctl installed. Tried with/out sudo

 vorg@x64VDR:~$ smartctl -a /dev/sda
 -bash: smartctl: command not found

----------------------------------------------------------

vorg@x64VDR:~$ cat /proc/mdstat
Personalities : [raid1] [raid6] [raid5] [raid4] [multipath]
md1 : active raid1 sdb2[1] sda2[0]
      4891712 blocks [2/2] [UU]

md2 : active raid1 sdb3[1] sda3[0]

      459073344 blocks [2/2] [UU]

md3 : active raid1 sdd1[1] sdc1[0]

      488383936 blocks [2/2] [UU]

md0 : active raid1 sdb1[1] sda1[0]

      24418688 blocks [2/2] [UU]

unused devices: <none>
-------------------------------------------------------------

vorg@x64VDR:~$ sudo mdadm -D /dev/md0
/dev/md0:
        Version : 0.90
  Creation Time : Sat Oct  4 14:35:45 2008
     Raid Level : raid1
     Array Size : 24418688 (23.29 GiB 25.00 GB)
  Used Dev Size : 24418688 (23.29 GiB 25.00 GB)
   Raid Devices : 2
  Total Devices : 2
Preferred Minor : 0
    Persistence : Superblock is persistent

Update Time : Mon Aug 1 12:37:59 2011
State : active
Active Devices : 2
Working Devices : 2
Failed Devices : 0
Spare Devices : 0

           UUID : e4926be6:8d6f08e5:0ab6b006:621c4ec0 (local to host 

x64VDR)
Events : 0.648843

Number Major Minor RaidDevice State
0 8 1 0 active sync /dev/sda1
1 8 17 1 active sync /dev/sdb1
---------------------------------------------------------------------

vorg@x64VDR:~$ sudo mdadm -D /dev/md1
/dev/md1:
        Version : 0.90
  Creation Time : Sat Oct  4 14:42:18 2008
     Raid Level : raid1
     Array Size : 4891712 (4.67 GiB 5.01 GB)
  Used Dev Size : 4891712 (4.67 GiB 5.01 GB)
   Raid Devices : 2
  Total Devices : 2
Preferred Minor : 1
    Persistence : Superblock is persistent

Update Time : Sun Jul 31 11:45:49 2011
State : clean
Active Devices : 2
Working Devices : 2
Failed Devices : 0
Spare Devices : 0

           UUID : eac96451:66efa3ab:0ab6b006:621c4ec0 (local to host 

x64VDR)
Events : 0.550

Number Major Minor RaidDevice State
0 8 2 0 active sync /dev/sda2
1 8 18 1 active sync /dev/sdb2
---------------------------------------------------------------------

vorg@x64VDR:~$ sudo mdadm -D /dev/md2
/dev/md2:
        Version : 0.90
  Creation Time : Fri Jun  4 23:03:23 2010
     Raid Level : raid1
     Array Size : 459073344 (437.81 GiB 470.09 GB)
  Used Dev Size : 459073344 (437.81 GiB 470.09 GB)
   Raid Devices : 2
  Total Devices : 2
Preferred Minor : 2
    Persistence : Superblock is persistent

Update Time : Sun Jul 31 14:46:45 2011
State : clean
Active Devices : 2
Working Devices : 2
Failed Devices : 0
Spare Devices : 0

           UUID : 934b5d12:5f83677f:0ab6b006:621c4ec0 (local to host 

x64VDR)
Events : 0.29054

Number Major Minor RaidDevice State
0 8 3 0 active sync /dev/sda3
1 8 19 1 active sync /dev/sdb3
---------------------------------------------------------------------

vorg@x64VDR:~$ sudo mdadm -D /dev/md3
/dev/md3:
        Version : 0.90
  Creation Time : Wed Jun  2 17:54:03 2010
     Raid Level : raid1
     Array Size : 488383936 (465.76 GiB 500.11 GB)
  Used Dev Size : 488383936 (465.76 GiB 500.11 GB)
   Raid Devices : 2
  Total Devices : 2
Preferred Minor : 3
    Persistence : Superblock is persistent

Update Time : Sun Jul 31 14:46:45 2011
State : clean
Active Devices : 2
Working Devices : 2
Failed Devices : 0
Spare Devices : 0

           UUID : 47b3c905:5121e149:0ab6b006:621c4ec0 (local to host 

x64VDR)
Events : 0.2406

Number Major Minor RaidDevice State
0 8 33 0 active sync /dev/sdc1
1 8 49 1 active sync /dev/sdd1
---------------------------------------------------------------------
I do have it setup for email reports and last time a drive failed, that worked. I also have gotten emails about failed syncing which only happened a couple of times and it's been awhile since I got one of those. Likely fixed during an update somewhere along the way. It was thought to be a false report.

Received: by vorgon.com (sSMTP sendmail emulation); Sun, 13 Jun 2010 00:57:02 -0700
Date: Sun, 13 Jun 2010 00:57:02 -0700
From: root (Cron Daemon)
To: root
Subject: Cron <root@x64VDR> [ -x /usr/share/mdadm/checkarray ] && [ $(date +%d) -le 7 ] && /usr/share/mdadm/checkarray --cron --all --quiet (failed)
Content-Type: text/plain; charset=UTF-8
X-Cron-Env: <SHELL=/bin/sh>
X-Cron-Env: <HOME=/root>
X-Cron-Env: <PATH=/usr/bin:/bin>
X-Cron-Env: <LOGNAME=root>
Message-Id: <[email protected]>
X-Provags-ID: V01U2FsdGVkX1/bTJj+AQvAeW7xRwAd2EQ+S8duRn/uPMxwyFG
T6yf7bTnrgufCTUjkhnj4mQsIilzGEu+VDKrLyFu7t2itTaVgM
tshSGVhqbbiQbc1myOVEg==
Envelope-To: [email protected]
X-Antivirus: avast! (VPS 100602-1, 06/02/2010), Inbound message
X-Antivirus-Status: Clean

command failed with exit status 1

--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#3 lore raw
Quoted 4 lines · Timothy D. Lenz

Don't think I have smartctl installed. Tried with/out sudo

 vorg@x64VDR:~$ smartctl -a /dev/sda
 -bash: smartctl: command not found

So install it, or compile it from source and run it (smartmontools). It would be interesting to see if you have a problem with HDDs/controllers/backplanes/cables.

/M
--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#4 lore raw
vorg@x64VDR:~$ sudo smartctl -a /dev/sda
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-2.6.34.20100610.1] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===

Model Family:     Seagate Barracuda 7200.11
Device Model:     ST3500320AS
Serial Number:    9QM7M86S
LU WWN Device Id: 5 000c50 01059c636
Firmware Version: SD1A
User Capacity:    500,107,862,016 bytes [500 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   8
ATA Standard is:  ATA-8-ACS revision 4
Local Time is:    Mon Aug  1 16:11:16 2011 MST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error. Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: ( 650) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new command.
Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode. Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 119) minutes.
Conveyance self-test routine

recommended polling time:        (   2) minutes.
SCT capabilities:              (0x103b) SCT Status supported.

SCT Error Recovery Control
supported.
SCT Feature Control supported. SCT Data Table supported.

SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   114   100   006    Pre-fail 

Always - 82804896
3 Spin_Up_Time 0x0003 094 094 000 Pre-fail
Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age
Always - 13
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 070 060 030 Pre-fail
Always - 12546791
9 Power_On_Hours 0x0032 095 095 000 Old_age
Always - 4807
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age
Always - 13
184 End-to-End_Error 0x0032 100 100 099 Old_age Always
- 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always
- 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always
- 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always
- 0
190 Airflow_Temperature_Cel 0x0022 067 065 045 Old_age Always
- 33 (Min/Max 30/34)
194 Temperature_Celsius 0x0022 033 040 000 Old_age Always
- 33 (0 21 0 0)
195 Hardware_ECC_Recovered 0x001a 054 033 000 Old_age Always
- 82804896
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 0

198 Offline_Uncorrectable   0x0010   100   100   000    Old_age Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always 

- 0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1

 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing

Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
-------------------------------------------------------------------------------------------

vorg@x64VDR:~$ sudo smartctl -a /dev/sdb
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-2.6.34.20100610.1] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===

Model Family:     Seagate Barracuda 7200.11
Device Model:     ST3500320AS
Serial Number:    9QM1P092
LU WWN Device Id: 5 000c50 0098f53ba
Firmware Version: SD15
User Capacity:    500,107,862,016 bytes [500 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   8
ATA Standard is:  ATA-8-ACS revision 4
Local Time is:    Mon Aug  1 16:12:14 2011 MST

==> WARNING: There are known problems with these drives, AND THIS FIRMWARE VERSION IS AFFECTED,
see the following Seagate web pages:
http://seagate.custkb.com/seagate/crm/selfservice/search.jsp?DocId=207931
http://seagate.custkb.com/seagate/crm/selfservice/search.jsp?DocId=207951

SMART support is: Available - device has SMART capability. SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error. Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: ( 625) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new command.
Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode. Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 113) minutes.
Conveyance self-test routine

recommended polling time:        (   2) minutes.
SCT capabilities:              (0x103b) SCT Status supported.

SCT Error Recovery Control
supported.
SCT Feature Control supported. SCT Data Table supported.

SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   113   099   006    Pre-fail 

Always - 52352187
3 Spin_Up_Time 0x0003 094 094 000 Pre-fail
Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age
Always - 39
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 078 060 030 Pre-fail
Always - 64855982
9 Power_On_Hours 0x0032 072 072 000 Old_age
Always - 24685
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 037 020 Old_age
Always - 39
184 End-to-End_Error 0x0032 100 100 099 Old_age Always
- 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always
- 0
188 Command_Timeout 0x0032 100 098 000 Old_age Always
- 20
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always
- 0
190 Airflow_Temperature_Cel 0x0022 066 062 045 Old_age Always
- 34 (Min/Max 30/35)
194 Temperature_Celsius 0x0022 034 040 000 Old_age Always
- 34 (0 22 0 0)
195 Hardware_ECC_Recovered 0x001a 029 023 000 Old_age Always
- 52352187
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 0

198 Offline_Uncorrectable   0x0010   100   100   000    Old_age Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always 

- 0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1

 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing

Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
-------------------------------------------------------------------------------------------

vorg@x64VDR:~$ sudo smartctl -a /dev/sdc
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-2.6.34.20100610.1] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===

Model Family:     Seagate Barracuda 7200.11
Device Model:     ST3500320AS
Serial Number:    9QM35MY5
LU WWN Device Id: 5 000c50 00b9fbd80
Firmware Version: SD15
User Capacity:    500,107,862,016 bytes [500 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   8
ATA Standard is:  ATA-8-ACS revision 4
Local Time is:    Mon Aug  1 16:13:15 2011 MST

==> WARNING: There are known problems with these drives, AND THIS FIRMWARE VERSION IS AFFECTED,
see the following Seagate web pages:
http://seagate.custkb.com/seagate/crm/selfservice/search.jsp?DocId=207931
http://seagate.custkb.com/seagate/crm/selfservice/search.jsp?DocId=207951

SMART support is: Available - device has SMART capability. SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error. Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: ( 634) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new command.
Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode. Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 113) minutes.
Conveyance self-test routine

recommended polling time:        (   2) minutes.
SCT capabilities:              (0x103b) SCT Status supported.

SCT Error Recovery Control
supported.
SCT Feature Control supported. SCT Data Table supported.

SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   119   099   006    Pre-fail 

Always - 220520828
3 Spin_Up_Time 0x0003 094 094 000 Pre-fail
Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age
Always - 39
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 074 060 030 Pre-fail
Always - 8642691180
9 Power_On_Hours 0x0032 072 072 000 Old_age
Always - 24685
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age
Always - 39
184 End-to-End_Error 0x0032 100 100 099 Old_age Always
- 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always
- 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always
- 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always
- 0
190 Airflow_Temperature_Cel 0x0022 066 061 045 Old_age Always
- 34 (Min/Max 30/36)
194 Temperature_Celsius 0x0022 034 040 000 Old_age Always
- 34 (0 22 0 0)
195 Hardware_ECC_Recovered 0x001a 028 021 000 Old_age Always
- 220520828
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 0

198 Offline_Uncorrectable   0x0010   100   100   000    Old_age Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always 

- 0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1

 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing

Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
-------------------------------------------------------------------------------------------

vorg@x64VDR:~$ sudo smartctl -a /dev/sdd
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-2.6.34.20100610.1] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===

Model Family:     Seagate Barracuda 7200.11
Device Model:     ST3500820AS
Serial Number:    9QM6V6JF
LU WWN Device Id: 5 000c50 009cb8c4c
Firmware Version: SD1A
User Capacity:    500,107,862,016 bytes [500 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   8
ATA Standard is:  ATA-8-ACS revision 4
Local Time is:    Mon Aug  1 16:14:04 2011 MST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error. Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: ( 634) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new command.
Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode. Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 114) minutes.
Conveyance self-test routine

recommended polling time:        (   2) minutes.
SCT capabilities:              (0x103b) SCT Status supported.

SCT Error Recovery Control
supported.
SCT Feature Control supported. SCT Data Table supported.

SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   119   099   006    Pre-fail 

Always - 205159952
3 Spin_Up_Time 0x0003 094 094 000 Pre-fail
Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age
Always - 34
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 072 060 030 Pre-fail
Always - 15541587
9 Power_On_Hours 0x0032 088 088 000 Old_age
Always - 10726
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age
Always - 34
184 End-to-End_Error 0x0032 100 100 099 Old_age Always
- 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always
- 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always
- 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always
- 0
190 Airflow_Temperature_Cel 0x0022 065 062 045 Old_age Always
- 35 (Min/Max 30/37)
194 Temperature_Celsius 0x0022 035 040 000 Old_age Always
- 35 (0 23 0 0)
195 Hardware_ECC_Recovered 0x001a 049 023 000 Old_age Always
- 205159952
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 0

198 Offline_Uncorrectable   0x0010   100   100   000    Old_age Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always 

- 0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1

 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing

Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
-------------------------------------------------------------------------------------------

Quoted 6 lines · Mathias Burén
Quoted 4 lines · Timothy D. Lenz

Don't think I have smartctl installed. Tried with/out sudo

  vorg@x64VDR:~$ smartctl -a /dev/sda
  -bash: smartctl: command not found
Quoted 6 lines

So install it, or compile it from source and run it (smartmontools). It would be interesting to see if you have a problem with HDDs/controllers/backplanes/cables.

/M

--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#5 lore raw
In reply to Timothy D. Lenz
Quoted 5 lines · Timothy D. Lenz
Quoted 4 lines · Mathias Burén
Quoted 3 lines · Timothy D. Lenz

Looking through the logs, I found this in daemon.log.0. Is this a sign of a
problem? Below is the entire log:

[...]

Quoted 2 lines
Quoted 2 lines
Quoted 2 lines

Jul 3 01:03:01 x64VDR mdadm[2003]: RebuildFinished event detected on md device /dev/md1, component device mismatches found: 9600

[...]

Quoted 2 lines

md1 : active raid1 sdb2[1] sda2[0]
4891712 blocks [2/2] [UU]

Hmm. Is this 5GB RAID-1 your swap partition? If so, don't worry about it - there is an oddity that mismatches can crop up on RAID-1 arrays when a write is abandoned after one drive has been written but the other hasn't (I think that's the explanation), it's most often seen on swap, and it's harmless.

Red Hat disabled reporting mismatches on RAID-1 because of this.

Cheers,

John.

--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html