How to make bi-directional NAT'ting?
Hello!
I have some specific problem with Cisco CP7961G IP phone. It sends packets to external Softswitch using one UDP port which differs from 5060 (voipControlPort in its .XML), but it waits answers on 5060!
And I can't do anything with it! I have tried Firmware from 8.0.x up to 8.5.x - all the same!
One thing I think is make corresponding translation on IPTables. SNAT in direct path (from 79161 to Softswitch) and DNAT in backward direction (from outside Softswitch to 7961).
BUT IT DOESN'T WORK! :-)
$IPTABLES -t nat -A PREROUTING -p udp -s 80.251.x.x
-d 80.251.y.y --dport 5060 -j DNAT
--to-destination 172.16.128.200:5060
$IPTABLES -t nat -A POSTROUTING -o eth0 -p udp -s 172.16.128.0/24 --sport 1024:65535 -d 80.251.x.x --dport 5060 -j SNAT --to-source 80.251.y.y:5060
What do I do wrong?
Kind regards,
Ellad Yatsko
Quoted 13 lines · ���� ����� ����������� (ngs)
Hello!
I have some specific problem with Cisco CP7961G IP phone. It sends packets to external Softswitch using one UDP port which differs from 5060 (voipControlPort in its .XML), but it waits answers on 5060!
And I can't do anything with it! I have tried Firmware from 8.0.x up to 8.5.x - all the same!One thing I think is make corresponding translation on IPTables. SNAT in direct path (from 79161 to Softswitch) and DNAT in backward direction (from outside Softswitch to 7961).
Quoted 7 lines
BUT IT DOESN'T WORK! :-)
$IPTABLES -t nat -A PREROUTING -p udp -s 80.251.x.x
-d 80.251.y.y --dport 5060 -j DNAT --to-destination172.16.128.200:5060
$IPTABLES -t nat -A POSTROUTING -o eth0 -p udp -s 172.16.128.0/24 --sport
1024:65535 -d 80.251.x.x --dport 5060 -j SNAT --to-source 80.251.y.y:5060
SIP is difficult to correct with NAT. It includes connection data at layer
7. So the Softswitch may be ignoring packet headers and replying to that.
I don't think NAT is your solution here. Something else is wrong in the SIP setup of this device.
Regards,
Tyler
Signature · 6 lines
"[...] the effectiveness of pat-downs does not matter very much, because
the obvious goal of the TSA is to make the pat-down embarrassing enough
for the average passenger that the vast majority of people will choose
high-tech humiliation over the low-tech ball check."
-- Jeffrey Goldberg, "For the First Time, the TSA Meets Resistance"
The Atlantic, 2010-10-29A message that is not in the archive (sent off-list or not yet received): [email protected]
Re:
Quoted 5 lines · Ellad Yatsko
Main problem is DNAT does not work as I wait. It seems to me there is an implicit additional
DNAT rule for SNAT, and because *my* DNAT rule does not work. May you show me how it
could be "switched off"? :-)
It's not an implicit rule. If either rule matches the FIRST time the traffic is seen, it will become an established connection. NAT will be applied to it in both directions. See the current list of tracked connections with:
cat /proc/net/ip_conntrack
Don't run that on a system with a lot of traffic. You'll get one line for each session. For 1000 sessions, that's manageable. For 500,000, it will block the terminal for a long time.
Regards,
Tyler
Signature · 2 lines
"The map is not the territory." -- Alfred Korzybski
Re:
Quoted 12 lines · Tyler J. Wagner
Quoted 5 lines · Ellad Yatsko
Main problem is DNAT does not work as I wait. It seems to me there is an implicit additional
DNAT rule for SNAT, and because *my* DNAT rule does not work. May you show me how it
could be "switched off"? :-)It's not an implicit rule. If either rule matches the FIRST time the traffic is seen, it will become an established connection. NAT will be applied to it in both directions. See the current list of tracked connections with:
Quoted 5 lines
cat
/proc/net/ip_conntrackDon't run that on a system with a lot of traffic. You'll get one line for each session. For 1000 sessions, that's manageable. For 500,000, it will block the terminal for a long time.
That's why one normally uses conntrack -L | less so that that does not happen.
Re:
Quoted 6 lines · Jan Engelhardt
Quoted 3 lines
Don't run that on a system with a lot of traffic. You'll get one line for each session. For 1000 sessions, that's manageable. For 500,000, it will block the terminal for a long time.
That's why one normally uses conntrack -L | less so that that does not happen.
Unfortunately, conntrack isn't installed by default on a lot of distributions. Just "less /proc/..." will do the same.
Regards,
Tyler
Signature · 4 lines
"Religion is the opiate of the masses, so long as the masses are straight.
However, amass a bunch of lesbians and you're going to need actual drugs."
-- OKCupid Blog, with apologies to Karl Marx
http://blog.okcupid.com/index.php/gay-sex-vs-straight-sex/