higher N rates
$ iw dev wlan0 scan
printed this for my N (only) router:
Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0 Extended supported rates: 6.0 9.0 12.0 48.0
Why doesn't it print the higher N rates?
Quoted 8 lines · James
$ iw dev wlan0 scanprinted this for my N (only) router:
Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0 Extended supported rates: 6.0 9.0 12.0 48.0
Why doesn't it print the higher N rates?
I may be WAY off base here, but I believe iw dev wlan0 scan reports what's shown in the beacons, and not what rates are actually negotiable. Beacons only directly advertise 'pre-n' rates (the basic 802.11abg rates).
If you look at more of the scan results, you should see something like:
HT capabilities:
Capabilities: 0x11ce
HT20/HT40
SM Power Save disabled
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-15
HT operation:
* primary channel: 36
* secondary channel offset: above
* STA channel width: any
* RIFS: 0
* HT protection: no
* non-GF present: 0
* OBSS non-GF present: 0
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
Which outlines the 802.11n parameters that your device and the AP can use to negotiate 802.11n operation. Perhaps there is something more that should be reported, but you'll see throughputs in the 802.11n range WHEN it's warranted. With my DSL connection, I rarely see rates above 9mbit in use (my DSL is 1.5mbit down).
Pat
Quoted 12 lines
From: [email protected] [mailto:linux-wireless- [email protected]] On Behalf Of Pat Erley
Sent: zaterdag 24 september 2011 17:35Quoted 7 lines · James
$ iw dev wlan0 scanprinted this for my N (only) router:
Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0 Extended supported rates: 6.0 9.0 12.0 48.0
Quoted 7 lines
Quoted 1 line
Why doesn't it print the higher N rates?
I may be WAY off base here, but I believe iw dev wlan0 scan reports what's shown in the beacons, and not what rates are actually negotiable.
Beacons only directly advertise 'pre-n' rates (the basic 802.11abg rates).
I think you pretty close to base here ;-)
Quoted 14 lines
If you look at more of the scan results, you should see something like:
HT capabilities:
Capabilities:0x11ce
HT20/HT40
SM Power Save disabled
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent:0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-15
The 11n rates are expressed in MCS (Modulation and Coding Scheme) rate indexes, which translate to a bitrate. So it also advertises 11n rates albeit in a slightly different format.
Gr. AvS