Failed to launch barebox from flash memory on i.MX35
Hi all,
I just managed to compile the latest barebox source (http://barebox.org/download/barebox-2011.10.0.tar.bz2 <http://barebox.org/download/>) for the pcm043 board. I configured and compiled it:
$ make pcm043_defconfig $ make xconfig # nothing changed there $ make
I used the following CROSS environment settings:
export PATH="$PATH:/opt/OSELAS.Toolchain-1.99.3/arm-1136jfs-linux-gnueabi/gcc-4.3.2-glibc-2.8-binutils-2.19-kernel-2.6.27-sanitized/bin" export ARCH=arm
export CROSS_COMPILE=arm-1136jfs-linux-gnueabi-
The make went well without any problems.
I flashed the barebox.bin at address 0xa000_0000 and rebootet. The program then trapped while trying to relocate the code to SDRAM. The SDRAM is propperly initialized but the call to memcpy takes adress 0x9FFFE000 as source and 0x87F00000 as destination. 0x9FFFE000 is definitely not correct, it is 0x2000 below the start of the flash memory, obviously the same size as symbol _stext in the map when subtracting the base address.
Map:00038e50 A _barebox_image_size87f02000 T _stext87f02000 T _text
The source is in arch/arm/copu/start.c at line 122.
I am completly stuck. What went wrong?
Any help will be very much appreciated.
Regards, Peter
.config
#
# Automatically generated make config: don't edit
# Linux/arm 2011.10.0 Barebox Configuration
# Sun Oct 30 18:48:51 2011
#
# CONFIG_BOARD_LINKER_SCRIPT is not setCONFIG_GENERIC_LINKER_SCRIPT=yCONFIG_ARM=yCONFIG_ARM_LINUX=y
#
# System Type
#
# CONFIG_ARCH_AT91 is not set
# CONFIG_ARCH_EP93XX is not setCONFIG_ARCH_IMX=y
# CONFIG_ARCH_MXS is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_NOMADIK is not set
# CONFIG_ARCH_OMAP is not set
# CONFIG_ARCH_S3C24xx is not set
# CONFIG_ARCH_VERSATILE is not set
#
# Processor Type
#CONFIG_CPU_32=yCONFIG_CPU_V6=y
CONFIG_CPU_32v6=y
#
# processor features # # CONFIG_BOOT_ENDIANNESS_SWITCH is not set CONFIG_ARCH_HAS_L2X0=y CONFIG_CACHE_L2X0=y CONFIG_ARCH_TEXT_BASE=0x87f00000 CONFIG_BOARDINFO="Phytec phyCORE-i.MX35" CONFIG_ARCH_IMX_INTERNAL_BOOT=y # CONFIG_ARCH_IMX_EXTERNAL_BOOT is not set CONFIG_ARCH_IMX_INTERNAL_BOOT_NAND=y # CONFIG_ARCH_IMX_INTERNAL_BOOT_NOR is not set # CONFIG_ARCH_IMX_INTERNAL_BOOT_ONENAND is not set
#
# Freescale i.MX System-on-Chip
#
# CONFIG_ARCH_IMX1 is not set
# CONFIG_ARCH_IMX21 is not set
# CONFIG_ARCH_IMX25 is not set
# CONFIG_ARCH_IMX27 is not set
# CONFIG_ARCH_IMX31 is not setCONFIG_ARCH_IMX35=y
# CONFIG_ARCH_IMX51 is not set
# CONFIG_ARCH_IMX53 is not set
# CONFIG_MACH_EUKREA_CPUIMX35 is not set
# CONFIG_MACH_FREESCALE_MX35_3STACK is not setCONFIG_MACH_PCM043=y
# CONFIG_MACH_GUF_CUPID is not set
#
# Board specific settings
#CONFIG_PCM043_DISPLAY_SHARP=y
# CONFIG_PCM043_DISPLAY_TY090 is not set
#
# i.MX specific settings
#CONFIG_IMX_CLKO=yCONFIG_IMX_IIM=yCONFIG_IMX_IIM_FUSE_BLOW=yCONFIG_AEABI=y
#
# Arm specific settings
#CONFIG_CMD_ARM_CPUINFO=y
# CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS is not setCONFIG_ARM_EXCEPTIONS=yCONFIG_ARM_UNWIND=yCONFIG_DEFCONFIG_LIST="$ARCH_DEFCONFIG"CONFIG_GREGORIAN_CALENDER=yCONFIG_HAS_KALLSYMS=yCONFIG_HAS_MODULES=yCONFIG_CMD_MEMORY=yCONFIG_ENV_HANDLING=yCONFIG_GENERIC_GPIO=y
#
# General Settings
#CONFIG_LOCALVERSION_AUTO=yCONFIG_ENVIRONMENT_VARIABLES=y
#
# memory layout # CONFIG_MMU=y CONFIG_HAVE_CONFIGURABLE_TEXT_BASE=y CONFIG_TEXT_BASE=0x87F00000 CONFIG_HAVE_CONFIGURABLE_MEMORY_LAYOUT=y CONFIG_MEMORY_LAYOUT_DEFAULT=y # CONFIG_MEMORY_LAYOUT_FIXED is not set CONFIG_STACK_SIZE=0x8000 CONFIG_MALLOC_SIZE=0x1000000 # CONFIG_BROKEN is not set # CONFIG_EXPERIMENTAL is not set CONFIG_MALLOC_DLMALLOC=y CONFIG_KALLSYMS=y CONFIG_MACH_HAS_LOWLEVEL_INIT=y CONFIG_MACH_DO_LOWLEVEL_INIT=y CONFIG_PROMPT="barebox:" CONFIG_BAUDRATE=115200 CONFIG_LONGHELP=y CONFIG_CBSIZE=1024 CONFIG_MAXARGS=16 CONFIG_SHELL_HUSH=y # CONFIG_SHELL_SIMPLE is not set CONFIG_GLOB=y CONFIG_PROMPT_HUSH_PS2="> " CONFIG_HUSH_FANCY_PROMPT=y CONFIG_HUSH_GETOPT=y CONFIG_CMDLINE_EDITING=y CONFIG_AUTO_COMPLETE=y # CONFIG_MENU is not set # CONFIG_PASSWORD is not set CONFIG_DYNAMIC_CRC_TABLE=y CONFIG_ERRNO_MESSAGES=y CONFIG_TIMESTAMP=y CONFIG_CONSOLE_FULL=y CONFIG_CONSOLE_ACTIVATE_FIRST=y # CONFIG_OF_FLAT_TREE is not set CONFIG_PARTITION=y CONFIG_DEFAULT_ENVIRONMENT=y CONFIG_DEFAULT_ENVIRONMENT_GENERIC=y CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/pcm043/env" # CONFIG_POLLER is not set
#
# Debugging
#CONFIG_DEBUG_INFO=y
# CONFIG_ENABLE_FLASH_NOISE is not set
# CONFIG_ENABLE_PARTITION_NOISE is not set
# CONFIG_ENABLE_DEVICE_NOISE is not setCONFIG_COMMAND_SUPPORT=y
#
# commands #
#
# scripting # CONFIG_CMD_EDIT=y CONFIG_CMD_SLEEP=y CONFIG_CMD_SAVEENV=y CONFIG_CMD_LOADENV=y CONFIG_CMD_EXPORT=y CONFIG_CMD_PRINTENV=y CONFIG_CMD_READLINE=y CONFIG_CMD_TRUE=y CONFIG_CMD_FALSE=y # CONFIG_CMD_LOGIN is not set # CONFIG_CMD_PASSWD is not set # CONFIG_CMD_TIME is not set
#
# file commands # CONFIG_CMD_LS=y CONFIG_CMD_RM=y CONFIG_CMD_CAT=y CONFIG_CMD_MKDIR=y CONFIG_CMD_RMDIR=y CONFIG_CMD_CP=y CONFIG_CMD_PWD=y CONFIG_CMD_CD=y CONFIG_CMD_MOUNT=y CONFIG_CMD_UMOUNT=y CONFIG_CMD_NAND=y
#
# console # CONFIG_CMD_CLEAR=y CONFIG_CMD_ECHO=y CONFIG_CMD_ECHO_E=y
#
# memory # # CONFIG_CMD_LOADB is not set # CONFIG_CMD_LOADS is not set CONFIG_CMD_MEMINFO=y CONFIG_CMD_CRC=y CONFIG_CMD_CRC_CMP=y # CONFIG_CMD_MD5SUM is not set # CONFIG_CMD_SHA1SUM is not set # CONFIG_CMD_SHA256SUM is not set # CONFIG_CMD_MTEST is not set
#
# flash # CONFIG_CMD_FLASH=y CONFIG_CMD_UBI=y
#
# booting # CONFIG_CMD_BOOTM=y # CONFIG_CMD_BOOTM_ZLIB is not set # CONFIG_CMD_BOOTM_BZLIB is not set # CONFIG_CMD_BOOTM_SHOW_TYPE is not set CONFIG_CMD_BOOTZ=y CONFIG_CMD_BOOTU=y CONFIG_CMD_RESET=y CONFIG_CMD_GO=y CONFIG_CMD_TIMEOUT=y CONFIG_CMD_PARTITION=y CONFIG_CMD_TEST=y CONFIG_CMD_VERSION=y CONFIG_CMD_HELP=y CONFIG_CMD_DEVINFO=y CONFIG_CMD_GPIO=y CONFIG_CMD_UNLZO=y CONFIG_NET=y CONFIG_NET_DHCP=y CONFIG_NET_NFS=y CONFIG_NET_PING=y CONFIG_NET_TFTP=y CONFIG_NET_TFTP_PUSH=y CONFIG_NET_NETCONSOLE=y # CONFIG_NET_RESOLV is not set # # Drivers # # # serial drivers # # CONFIG_DRIVER_SERIAL_ARM_DCC is not set CONFIG_DRIVER_SERIAL_IMX=y # CONFIG_DRIVER_SERIAL_NS16550 is not set CONFIG_ARCH_HAS_FEC_IMX=y CONFIG_MIIDEV=y # # Network drivers # # CONFIG_DRIVER_NET_SMC911X is not set # CONFIG_DRIVER_NET_SMC91111 is not set CONFIG_DRIVER_NET_FEC_IMX=y # # SPI drivers # # CONFIG_SPI is not set # CONFIG_I2C is not set
#
# flash drivers # CONFIG_DRIVER_CFI=y CONFIG_HAS_CFI=y CONFIG_DRIVER_CFI_INTEL=y CONFIG_DRIVER_CFI_AMD=y CONFIG_DRIVER_CFI_BANK_WIDTH_1=y CONFIG_DRIVER_CFI_BANK_WIDTH_2=y CONFIG_DRIVER_CFI_BANK_WIDTH_4=y # CONFIG_DRIVER_CFI_BANK_WIDTH_8 is not set CONFIG_CFI_BUFFER_WRITE=y CONFIG_MTD=y CONFIG_NAND=y CONFIG_NAND_WRITE=y CONFIG_NAND_ECC_SOFT=y CONFIG_NAND_ECC_HW=y CONFIG_NAND_ECC_HW_SYNDROME=y CONFIG_NAND_ECC_HW_NONE=y CONFIG_NAND_INFO=y CONFIG_NAND_BBT=y CONFIG_NAND_READ_OOB=y CONFIG_NAND_IMX=y # CONFIG_MTD_NAND_VERIFY_WRITE is not set # CONFIG_MTD_NAND_ECC_SMC is not set CONFIG_MTD_NAND_IDS=y CONFIG_UBI=y # CONFIG_ATA is not set # CONFIG_USB is not set # CONFIG_USB_GADGET is not set # CONFIG_VIDEO is not set # CONFIG_MCI is not set
#
# MFD
#
# CONFIG_LED is not set
#
# EEPROM support
#
#
# Filesystem support
#
# CONFIG_FS_CRAMFS is not setCONFIG_FS_RAMFS=yCONFIG_FS_DEVFS=y
# CONFIG_FS_FAT is not setCONFIG_PARTITION_NEED_MTD=yCONFIG_CRC32=y
# CONFIG_DIGEST is not set
# CONFIG_GENERIC_FIND_NEXT_BIT is not setCONFIG_PROCESS_ESCAPE_SEQUENCE=yCONFIG_LZO_DECOMPRESS=y
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Hi Peter,
Quoted 26 lines · Peter
Hi all,
I just managed to compile the latest barebox source (http://barebox.org/download/barebox-2011.10.0.tar.bz2 <http://barebox.org/download/>) for the pcm043 board. I configured and compiled it:$ make pcm043_defconfig $ make xconfig # nothing changed there $ makeI used the following CROSS environment settings:
export PATH="$PATH:/opt/OSELAS.Toolchain-1.99.3/arm-1136jfs-linux-gnueabi/gcc-4.3.2-glibc-2.8-binutils-2.19-kernel-2.6.27-sanitized/bin" export ARCH=arm
export CROSS_COMPILE=arm-1136jfs-linux-gnueabi-The make went well without any problems.
I flashed the barebox.bin at address 0xa000_0000 and rebootet. The program then trapped while trying to relocate the code to SDRAM. The SDRAM is propperly initialized but the call to memcpy takes adress0x9FFFE000as source and0x87F00000as destination.0x9FFFE000is definitely not correct, it is0x2000below the start of the flash memory, obviously the same size as symbol_stextin the map when subtracting the base address.Map:
00038e50A_barebox_image_size87f02000T_stext87f02000T_text
Quoted 4 lines
The source is in
arch/arm/copu/start.cat line 122.I am completly stuck. What went wrong?
Any help will be very much appreciated.
There seems to be a bug in the pcm043_defconfig. It is configured for internal bootmode, which means that the board has to specify a header of size 0x2000 before the actual image. The pcm043 does not specify this header as it uses the external bootmode.
Please disable CONFIG_ARCH_IMX_INTERNAL_BOOT in your config, that should do it. If it works I'll commit a corresponding patch.
Sascha
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Issue when building Barebox with ARM EABI 4.4.3
Hi all,
After building Barebox with arm-eabi 4.4.3, Barebox start-up properly but I got "command not found" error. I checked system.map and found that there is no API from//command/ folder.
But everything is OK with arm-eabi 4.4.0.
So I think the problem comes from 4.4.3 ?
Anyone can help me ?
Best regards,
LocN
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Am 02.11.2011 11:16, schrieb Sascha Hauer:
Quoted 33 lines
Hi Peter,
Quoted 26 lines · Peter
Hi all,
I just managed to compile the latest barebox source (http://barebox.org/download/barebox-2011.10.0.tar.bz2 <http://barebox.org/download/>) for the pcm043 board. I configured and compiled it:$ make pcm043_defconfig $ make xconfig # nothing changed there $ makeI used the following CROSS environment settings:
export PATH="$PATH:/opt/OSELAS.Toolchain-1.99.3/arm-1136jfs-linux-gnueabi/gcc-4.3.2-glibc-2.8-binutils-2.19-kernel-2.6.27-sanitized/bin" export ARCH=arm
export CROSS_COMPILE=arm-1136jfs-linux-gnueabi-The make went well without any problems.
I flashed the barebox.bin at address 0xa000_0000 and rebootet. The program then trapped while trying to relocate the code to SDRAM. The SDRAM is propperly initialized but the call to memcpy takes adress0x9FFFE000as source and0x87F00000as destination.0x9FFFE000is definitely not correct, it is0x2000below the start of the flash memory, obviously the same size as symbol_stextin the map when subtracting the base address.Map:
00038e50A_barebox_image_size87f02000T_stext87f02000T_textQuoted 4 lines
The source is in
arch/arm/copu/start.cat line 122.I am completly stuck. What went wrong?
Any help will be very much appreciated.
Quoted 9 lines
There seems to be a bug in the
pcm043_defconfig. It is configured for internal bootmode, which means that the board has to specify a header of size0x2000before the actual image. The pcm043 does not specify this header as it uses the external bootmode.
Please disableCONFIG_ARCH_IMX_INTERNAL_BOOTin your config, that should do it. If it works I'll commit a corresponding patch.Sascha
Thanks, that did the trick. I changed the option "support internal boot mode" to "support external boot mode" (What ever that means) and the relocation works pretty well now.
Nevertheless, next problem appears right after relocation. The console displays the welcome messages: "barebox 2011.10.0 (Nov 2 2011 - 14:40:11)" and "Board: Phytec phyCORE-i.MX35" but then loops in mmu.c at function mmu_init in the for () loop at line 237 .. forever!
Is there another secret word to be known?
Regards, Peter Kuennemann
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Quoted 12 lines · On Wed, Nov 02, 2011 at 03:04:26PM +0100, Peter Kuennemann@Crane-Soft wrote:
Am 02.11.2011 11:16, schrieb Sascha Hauer:
Quoted 10 lines
Quoted 3 lines
I am completly stuck. What went wrong?
Any help will be very much appreciated.There seems to be a bug in the
pcm043_defconfig. It is configured for internal bootmode, which means that the board has to specify a header of size0x2000before the actual image. The pcm043 does not specify this header as it uses the external bootmode.
Please disableCONFIG_ARCH_IMX_INTERNAL_BOOTin your config, that should do it. If it works I'll commit a corresponding patch.
Quoted 5 lines
Quoted 2 lines
Sascha
Thanks, that did the trick. I changed the option "support internal boot mode" to "support external boot mode" (What ever that means) and the relocation works pretty well now.
It's described in the i.MX datasheet. Internal bootmode means that after reset the internal ROM is executed which parses a header in flash or on a SD Card. The header describes how to setup memory, where to load the image and so on. In external bootmode the i.MX simply executes the code in NOR flash after reset.
Quoted 5 lines
Nevertheless, next problem appears right after relocation. The console displays the welcome messages: "barebox 2011.10.0 (Nov 2 2011 - 14:40:11)" and "Board: Phytec phyCORE-i.MX35" but then loops in
mmu.cat functionmmu_initin the for () loop at line 237 .. forever!
Strange. I just flashed a pcm043 with v2011.10.0 pcm043_defconfig + external bootmode and it works for me. As you have printf available can you put something like this into the loop?
printf("0x%08x 0x%08x\n", mem->start, mem->size)Sascha
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Am 02.11.2011 15:04, schrieb Peter Kuennemann@Crane-Soft:
Quoted 47 lines
Am 02.11.2011 11:16, schrieb Sascha Hauer:
Quoted 33 lines
Hi Peter,
Quoted 26 lines · Peter
Hi all,
I just managed to compile the latest barebox source (http://barebox.org/download/barebox-2011.10.0.tar.bz2 <http://barebox.org/download/>) for the pcm043 board. I configured and compiled it:$ make pcm043_defconfig $ make xconfig # nothing changed there $ makeI used the following CROSS environment settings:
export PATH="$PATH:/opt/OSELAS.Toolchain-1.99.3/arm-1136jfs-linux-gnueabi/gcc-4.3.2-glibc-2.8-binutils-2.19-kernel-2.6.27-sanitized/bin" export ARCH=arm
export CROSS_COMPILE=arm-1136jfs-linux-gnueabi-The make went well without any problems.
I flashed the barebox.bin at address 0xa000_0000 and rebootet. The program then trapped while trying to relocate the code to SDRAM. The SDRAM is propperly initialized but the call to memcpy takes adress0x9FFFE000as source and0x87F00000as destination.0x9FFFE000is definitely not correct, it is0x2000below the start of the flash memory, obviously the same size as symbol_stextin the map when subtracting the base address.Map:
00038e50A_barebox_image_size87f02000T_stext87f02000T_textQuoted 4 lines
The source is in
arch/arm/copu/start.cat line 122.I am completly stuck. What went wrong?
Any help will be very much appreciated.Quoted 9 lines
There seems to be a bug in the
pcm043_defconfig. It is configured for internal bootmode, which means that the board has to specify a header of size0x2000before the actual image. The pcm043 does not specify this header as it uses the external bootmode.
Please disableCONFIG_ARCH_IMX_INTERNAL_BOOTin your config, that should do it. If it works I'll commit a corresponding patch.Sascha
Thanks, that did the trick. I changed the option "support internal boot mode" to "support external boot mode" (What ever that means) and the relocation works pretty well now.
Quoted 8 lines
Nevertheless, next problem appears right after relocation. The console displays the welcome messages: "barebox 2011.10.0 (Nov 2 2011 - 14:40:11)" and "Board: Phytec phyCORE-i.MX35" but then loops in
mmu.cat functionmmu_initin the for () loop at line 237 .. forever!Is there another secret word to be known?
Regards, Peter Kuennemann
Just to finish this thread, I also disabled the MMU option which was set by default in the pcm043_defconfig. After isabling MMU barebox is running well.
Thanks for the support, Peter
Quoted 4 lines
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox