OMAP2+: UART: Runtime adaptation + cleanup

index bf089e7..a75f764 100644
@@ -30,7 +30,6 @@
 #include <linux/irq.h>
 #include <linux/time.h>
 #include <linux/gpio.h>
-#include <linux/console.h>
 
 #include <asm/mach/time.h>
 #include <asm/mach/irq.h>

@@ -133,27 +132,11 @@ static void omap2_enter_full_retention(void)
 	if (omap_irq_pending())
 		goto no_sleep;
 
-	/* Block console output in case it is on one of the OMAP UARTs */
-	if (!is_suspending())
-		if (!console_trylock())
-			goto no_sleep;
-
-	omap_uart_prepare_idle(0);
-	omap_uart_prepare_idle(1);
-	omap_uart_prepare_idle(2);
-
 	/* Jump to SRAM suspend code */
 	omap2_sram_suspend(sdrc_read_reg(SDRC_DLLA_CTRL),
 			   OMAP_SDRC_REGADDR(SDRC_DLLA_CTRL),
 			   OMAP_SDRC_REGADDR(SDRC_POWER));
 
-	omap_uart_resume_idle(2);
-	omap_uart_resume_idle(1);
-	omap_uart_resume_idle(0);
-
-	if (!is_suspending())
-		console_unlock();
-
 no_sleep:
 	if (omap2_pm_debug) {
 		unsigned long long tmp;

@@ -317,7 +300,6 @@ static int omap2_pm_suspend(void)
 	mir1 = omap_readl(0x480fe0a4);
 	omap_writel(1 << 5, 0x480fe0ac);
 
-	omap_uart_prepare_suspend();
 	omap2_enter_full_retention();
 
 	omap_writel(mir1, 0x480fe0a4);

index 4bbf1cd..6e7f276 100644
@@ -28,7 +28,6 @@
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/slab.h>
-#include <linux/console.h>
 #include <linux/mfd/omap-prm.h>
 #include <trace/events/power.h>
 

@@ -341,18 +340,9 @@ void omap_sram_idle(void)
 		omap3_enable_io_chain();
 	}
 
-	/* Block console output in case it is on one of the OMAP UARTs */
-	if (!is_suspending())
-		if (per_next_state < PWRDM_POWER_ON ||
-		    core_next_state < PWRDM_POWER_ON)
-			if (!console_trylock())
-				goto console_still_active;
-
 	/* PER */
 	if (per_next_state < PWRDM_POWER_ON) {
 		per_going_off = (per_next_state == PWRDM_POWER_OFF) ? 1 : 0;
-		omap_uart_prepare_idle(2);
-		omap_uart_prepare_idle(3);
 		omap2_gpio_prepare_for_idle(per_going_off);
 		if (per_next_state == PWRDM_POWER_OFF)
 				omap3_per_save_context();

@@ -360,8 +350,6 @@ void omap_sram_idle(void)
 
 	/* CORE */
 	if (core_next_state < PWRDM_POWER_ON) {
-		omap_uart_prepare_idle(0);
-		omap_uart_prepare_idle(1);
 		if (core_next_state == PWRDM_POWER_OFF) {
 			omap3_core_save_context();
 			omap3_cm_save_context();

@@ -408,8 +396,6 @@ void omap_sram_idle(void)
 			omap3_sram_restore_context();
 			omap2_sms_restore_context();
 		}
-		omap_uart_resume_idle(0);
-		omap_uart_resume_idle(1);
 		if (core_next_state == PWRDM_POWER_OFF)
 			omap2_prm_clear_mod_reg_bits(OMAP3430_AUTO_OFF_MASK,
 					       OMAP3430_GR_MOD,

@@ -423,14 +409,8 @@ void omap_sram_idle(void)
 		omap2_gpio_resume_after_idle();
 		if (per_prev_state == PWRDM_POWER_OFF)
 			omap3_per_restore_context();
-		omap_uart_resume_idle(2);
-		omap_uart_resume_idle(3);
 	}
 
-	if (!is_suspending())
-		console_unlock();
-
-console_still_active:
 	/* Disable IO-PAD and IO-CHAIN wakeup */
 	if (omap3_has_io_wakeup() &&
 	    (per_next_state < PWRDM_POWER_ON ||

@@ -493,7 +473,6 @@ static int omap3_pm_suspend(void)
 			goto restore;
 	}
 
-	omap_uart_prepare_suspend();
 	omap3_intc_suspend();
 
 	omap_sram_idle();

@@ -540,14 +519,12 @@ static int omap3_pm_begin(suspend_state_t state)
 {
 	disable_hlt();
 	suspend_state = state;
-	omap_uart_enable_irqs(0);
 	return 0;
 }
 
 static void omap3_pm_end(void)
 {
 	suspend_state = PM_SUSPEND_ON;
-	omap_uart_enable_irqs(1);
 	enable_hlt();
 	return;
 }

77 lines not on this page · raw message

index de3b10c..fc8b60c 100644
@@ -111,10 +111,6 @@ extern void omap_serial_init(void);
 extern void omap_serial_init_port(struct omap_board_data *bdata);
 extern int omap_uart_can_sleep(void);
 extern void omap_uart_check_wakeup(void);
-extern void omap_uart_prepare_suspend(void);
-extern void omap_uart_prepare_idle(int num);
-extern void omap_uart_resume_idle(int num);
-extern void omap_uart_enable_irqs(int enable);
 #endif
 
 #endif

index 62d15ad..61b260a 100644
@@ -19,23 +19,17 @@
  */
 #include <linux/kernel.h>
 #include <linux/init.h>
-#include <linux/serial_reg.h>
 #include <linux/clk.h>
 #include <linux/io.h>
 #include <linux/delay.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
-#include <linux/serial_8250.h>
 #include <linux/pm_runtime.h>
 #include <linux/console.h>
 
-#ifdef CONFIG_SERIAL_OMAP
 #include <plat/omap-serial.h>
-#endif
-
 #include <plat/common.h>
 #include <plat/board.h>
-#include <plat/clock.h>
 #include <plat/dma.h>
 #include <plat/omap_hwmod.h>
 #include <plat/omap_device.h>

@@ -47,10 +41,8 @@
 #include "control.h"
 #include "mux.h"
 
-#define UART_OMAP_NO_EMPTY_FIFO_READ_IP_REV	0x52
 #define UART_OMAP_WER		0x17	/* Wake-up enable register */
 
-#define UART_ERRATA_FIFO_FULL_ABORT	(0x1 << 0)
 #define UART_ERRATA_i202_MDR1_ACCESS	(0x1 << 1)
 
 /*

@@ -555,41 +547,6 @@ static void omap_uart_block_sleep(struct omap_uart_state *uart)
 #define DEV_CREATE_FILE(dev, attr)
 #endif /* CONFIG_PM */
 
-#ifndef CONFIG_SERIAL_OMAP
-/*
- * Override the default 8250 read handler: mem_serial_in()
- * Empty RX fifo read causes an abort on omap3630 and omap4
- * This function makes sure that an empty rx fifo is not read on these silicons
- * (OMAP1/2/3430 are not affected)
- */
-static unsigned int serial_in_override(struct uart_port *up, int offset)
-{
-	if (UART_RX == offset) {
-		unsigned int lsr;
-		lsr = __serial_read_reg(up, UART_LSR);
-		if (!(lsr & UART_LSR_DR))
-			return -EPERM;
-	}
-
-	return __serial_read_reg(up, offset);
-}
-
-static void serial_out_override(struct uart_port *up, int offset, int value)
-{
-	unsigned int status, tmout = 10000;
-
-	status = __serial_read_reg(up, UART_LSR);
-	while (!(status & UART_LSR_THRE)) {
-		/* Wait up to 10ms for the character(s) to be sent. */
-		if (--tmout == 0)
-			break;
-		udelay(1);
-		status = __serial_read_reg(up, UART_LSR);
-	}
-	__serial_write_reg(up, offset, value);
-}
-#endif
-
 static int __init omap_serial_early_init(void)
 {
 	int i = 0;

@@ -650,15 +607,7 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 	void *pdata = NULL;
 	u32 pdata_size = 0;
 	char *name;
-#ifndef CONFIG_SERIAL_OMAP
-	struct plat_serial8250_port ports[2] = {
-		{},
-		{.flags = 0},
-	};
-	struct plat_serial8250_port *p = &ports[0];
-#else
 	struct omap_uart_port_info omap_up;
-#endif
 
 	if (WARN_ON(!bdata))
 		return;

@@ -673,51 +622,6 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 
 	oh = uart->oh;
 	uart->dma_enabled = 0;
-#ifndef CONFIG_SERIAL_OMAP
-	name = "serial8250";
-
-	/*
-	 * !! 8250 driver does not use standard IORESOURCE* It
-	 * has it's own custom pdata that can be taken from
-	 * the hwmod resource data.  But, this needs to be
-	 * done after the build.
-	 *
-	 * ?? does it have to be done before the register ??
-	 * YES, because platform_device_data_add() copies
-	 * pdata, it does not use a pointer.
-	 */
-	p->flags = UPF_BOOT_AUTOCONF;
-	p->iotype = UPIO_MEM;
-	p->regshift = 2;
-	p->uartclk = OMAP24XX_BASE_BAUD * 16;
-	p->irq = oh->mpu_irqs[0].irq;
-	p->mapbase = oh->slaves[0]->addr->pa_start;
-	p->membase = omap_hwmod_get_mpu_rt_va(oh);
-	p->irqflags = IRQF_SHARED;
-	p->private_data = uart;
-
-	/*
-	 * omap44xx, ti816x: Never read empty UART fifo
-	 * omap3xxx: Never read empty UART fifo on UARTs
-	 * with IP rev >=0x52
-	 */
-	uart->regshift = p->regshift;
-	uart->membase = p->membase;
-	if (cpu_is_omap44xx() || cpu_is_ti816x())
-		uart->errata |= UART_ERRATA_FIFO_FULL_ABORT;
-	else if ((serial_read_reg(uart, UART_OMAP_MVER) & 0xFF)
-			>= UART_OMAP_NO_EMPTY_FIFO_READ_IP_REV)
-		uart->errata |= UART_ERRATA_FIFO_FULL_ABORT;
-
-	if (uart->errata & UART_ERRATA_FIFO_FULL_ABORT) {
-		p->serial_in = serial_in_override;
-		p->serial_out = serial_out_override;
-	}
-
-	pdata = &ports[0];
-	pdata_size = 2 * sizeof(struct plat_serial8250_port);
-#else
-
 	name = DRIVER_NAME;
 
 	omap_up.dma_enabled = uart->dma_enabled;

@@ -729,7 +633,6 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 
 	pdata = &omap_up;
 	pdata_size = sizeof(struct omap_uart_port_info);
-#endif
 
 	if (WARN_ON(!oh))
 		return;

index 61b260a..5632de5 100644
@@ -58,8 +58,6 @@
 struct omap_uart_state {
 	int num;
 	int can_sleep;
-	struct timer_list timer;
-	u32 timeout;
 
 	void __iomem *wk_st;
 	void __iomem *wk_en;

@@ -67,13 +65,9 @@ struct omap_uart_state {
 	u32 padconf;
 	u32 dma_enabled;
 
-	struct clk *ick;
-	struct clk *fck;
 	int clocked;
 
-	int irq;
 	int regshift;
-	int irqflags;
 	void __iomem *membase;
 	resource_size_t mapbase;
 

@@ -353,32 +347,6 @@ static void omap_uart_block_sleep(struct omap_uart_state *uart)
 
 	omap_uart_smart_idle_enable(uart, 0);
 	uart->can_sleep = 0;
-	if (uart->timeout)
-		mod_timer(&uart->timer, jiffies + uart->timeout);
-	else
-		del_timer(&uart->timer);
-}
-
-static void omap_uart_allow_sleep(struct omap_uart_state *uart)
-{
-	if (device_may_wakeup(&uart->pdev->dev))
-		omap_uart_enable_wakeup(uart);
-	else
-		omap_uart_disable_wakeup(uart);
-
-	if (!uart->clocked)
-		return;
-
-	omap_uart_smart_idle_enable(uart, 1);
-	uart->can_sleep = 1;
-	del_timer(&uart->timer);
-}
-
-static void omap_uart_idle_timer(unsigned long data)
-{
-	struct omap_uart_state *uart = (struct omap_uart_state *)data;
-
-	omap_uart_allow_sleep(uart);
 }
 
 int omap_uart_can_sleep(void)

@@ -402,35 +370,11 @@ int omap_uart_can_sleep(void)
 	return can_sleep;
 }
 
-/**
- * omap_uart_interrupt()
- *
- * This handler is used only to detect that *any* UART interrupt has
- * occurred.  It does _nothing_ to handle the interrupt.  Rather,
- * any UART interrupt will trigger the inactivity timer so the
- * UART will not idle or sleep for its timeout period.
- *
- **/
-/* static int first_interrupt; */
-static irqreturn_t omap_uart_interrupt(int irq, void *dev_id)
-{
-	struct omap_uart_state *uart = dev_id;
-
-	omap_uart_block_sleep(uart);
-
-	return IRQ_NONE;
-}
-
 static void omap_uart_idle_init(struct omap_uart_state *uart)
 {
 	int ret;
 
 	uart->can_sleep = 0;
-	uart->timeout = DEFAULT_TIMEOUT;
-	setup_timer(&uart->timer, omap_uart_idle_timer,
-		    (unsigned long) uart);
-	if (uart->timeout)
-		mod_timer(&uart->timer, jiffies + uart->timeout);
 	omap_uart_smart_idle_enable(uart, 0);
 
 	if (cpu_is_omap34xx() && !cpu_is_ti816x()) {

@@ -492,51 +436,8 @@ static void omap_uart_idle_init(struct omap_uart_state *uart)
 		uart->wk_mask = 0;
 		uart->padconf = 0;
 	}
-
-	uart->irqflags |= IRQF_SHARED;
-	ret = request_threaded_irq(uart->irq, NULL, omap_uart_interrupt,
-				   IRQF_SHARED, "serial idle", (void *)uart);
-	WARN_ON(ret);
-}
-
-static ssize_t sleep_timeout_show(struct device *dev,
-				  struct device_attribute *attr,
-				  char *buf)
-{
-	struct platform_device *pdev = to_platform_device(dev);
-	struct omap_device *odev = to_omap_device(pdev);
-	struct omap_uart_state *uart = odev->hwmods[0]->dev_attr;
-
-	return sprintf(buf, "%u\n", uart->timeout / HZ);
 }
 
-static ssize_t sleep_timeout_store(struct device *dev,
-				   struct device_attribute *attr,
-				   const char *buf, size_t n)
-{
-	struct platform_device *pdev = to_platform_device(dev);
-	struct omap_device *odev = to_omap_device(pdev);
-	struct omap_uart_state *uart = odev->hwmods[0]->dev_attr;
-	unsigned int value;
-
-	if (sscanf(buf, "%u", &value) != 1) {
-		dev_err(dev, "sleep_timeout_store: Invalid value\n");
-		return -EINVAL;
-	}
-
-	uart->timeout = value * HZ;
-	if (uart->timeout)
-		mod_timer(&uart->timer, jiffies + uart->timeout);
-	else
-		/* A zero value means disable timeout feature */
-		omap_uart_block_sleep(uart);
-
-	return n;
-}
-
-static DEVICE_ATTR(sleep_timeout, 0644, sleep_timeout_show,
-		sleep_timeout_store);
-#define DEV_CREATE_FILE(dev, attr) WARN_ON(device_create_file(dev, attr))
 #else
 static inline void omap_uart_idle_init(struct omap_uart_state *uart) {}
 static void omap_uart_block_sleep(struct omap_uart_state *uart)

@@ -544,7 +445,6 @@ static void omap_uart_block_sleep(struct omap_uart_state *uart)
 	/* Needed to enable UART clocks when built without CONFIG_PM */
 	omap_uart_enable_clocks(uart);
 }
-#define DEV_CREATE_FILE(dev, attr)
 #endif /* CONFIG_PM */
 
 static int __init omap_serial_early_init(void)

@@ -628,8 +528,7 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 	omap_up.uartclk = OMAP24XX_BASE_BAUD * 16;
 	omap_up.mapbase = oh->slaves[0]->addr->pa_start;
 	omap_up.membase = omap_hwmod_get_mpu_rt_va(oh);
-	omap_up.irqflags = IRQF_SHARED;
-	omap_up.flags = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
+	omap_up.flags = UPF_BOOT_AUTOCONF;
 
 	pdata = &omap_up;
 	pdata_size = sizeof(struct omap_uart_port_info);

@@ -646,7 +545,6 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 	omap_device_disable_idle_on_suspend(pdev);
 	oh->mux = omap_hwmod_mux_init(bdata->pads, bdata->pads_cnt);
 
-	uart->irq = oh->mpu_irqs[0].irq;
 	uart->regshift = 2;
 	uart->mapbase = oh->slaves[0]->addr->pa_start;
 	uart->membase = omap_hwmod_get_mpu_rt_va(oh);

@@ -669,24 +567,12 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 	omap_hwmod_enable_wakeup(uart->oh);
 	omap_device_idle(uart->pdev);
 
-	/*
-	 * Need to block sleep long enough for interrupt driven
-	 * driver to start.  Console driver is in polling mode
-	 * so device needs to be kept enabled while polling driver
-	 * is in use.
-	 */
-	if (uart->timeout)
-		uart->timeout = (30 * HZ);
 	omap_uart_block_sleep(uart);
-	uart->timeout = DEFAULT_TIMEOUT;
-
 	console_unlock();
 
 	if ((cpu_is_omap34xx() && uart->padconf) ||
-	    (uart->wk_en && uart->wk_mask)) {
+	    (uart->wk_en && uart->wk_mask))
 		device_init_wakeup(&pdev->dev, true);
-		DEV_CREATE_FILE(&pdev->dev, &dev_attr_sleep_timeout);
-	}
 
 	/* Enable the MDR1 errata for OMAP3 */
 	if (cpu_is_omap34xx() && !cpu_is_ti816x())

index 2682043..307cd6f 100644
@@ -61,7 +61,6 @@ struct omap_uart_port_info {
 	unsigned int		uartclk;	/* UART clock rate */
 	void __iomem		*membase;	/* ioremap cookie or NULL */
 	resource_size_t		mapbase;	/* resource base */
-	unsigned long		irqflags;	/* request_irq flags */
 	upf_t			flags;		/* UPF_* flags */
 };
 

index fc8b60c..a8bc1f1 100644
@@ -110,7 +110,6 @@ struct omap_board_data;
 extern void omap_serial_init(void);
 extern void omap_serial_init_port(struct omap_board_data *bdata);
 extern int omap_uart_can_sleep(void);
-extern void omap_uart_check_wakeup(void);
 #endif
 
 #endif

index 5e713d3..be368cf7 100644
@@ -1278,7 +1278,6 @@ static int serial_omap_probe(struct platform_device *pdev)
 	up->port.membase = omap_up_info->membase;
 	up->port.mapbase = omap_up_info->mapbase;
 	up->port.flags = omap_up_info->flags;
-	up->port.irqflags = omap_up_info->irqflags;
 	up->port.uartclk = omap_up_info->uartclk;
 	up->uart_dma.uart_base = mem->start;
 

index bd600cf..b12b38f 100644
@@ -482,106 +482,8 @@ static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
 static struct omap_board_mux board_mux[] __initdata = {
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
-
-static struct omap_device_pad serial1_pads[] __initdata = {
-	/*
-	 * Note that off output enable is an active low
-	 * signal. So setting this means pin is a
-	 * input enabled in off mode
-	 */
-	OMAP_MUX_STATIC("uart1_cts.uart1_cts",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart1_rts.uart1_rts",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart1_rx.uart1_rx",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart1_tx.uart1_tx",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial2_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart2_cts.uart2_cts",
-			 OMAP_PIN_INPUT_PULLUP |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rts.uart2_rts",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_rx.uart2_rx",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart2_tx.uart2_tx",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial3_pads[] __initdata = {
-	OMAP_MUX_STATIC("uart3_cts_rctx.uart3_cts_rctx",
-			 OMAP_PIN_INPUT_PULLDOWN |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rts_sd.uart3_rts_sd",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_rx_irrx.uart3_rx_irrx",
-			 OMAP_PIN_INPUT |
-			 OMAP_PIN_OFF_INPUT_PULLDOWN |
-			 OMAP_OFFOUT_EN |
-			 OMAP_MUX_MODE0),
-	OMAP_MUX_STATIC("uart3_tx_irtx.uart3_tx_irtx",
-			 OMAP_PIN_OUTPUT |
-			 OMAP_OFF_EN |
-			 OMAP_MUX_MODE0),
-};
-
-static struct omap_board_data serial1_data __initdata = {
-	.id		= 0,
-	.pads		= serial1_pads,
-	.pads_cnt	= ARRAY_SIZE(serial1_pads),
-};
-
-static struct omap_board_data serial2_data __initdata = {
-	.id		= 1,
-	.pads		= serial2_pads,
-	.pads_cnt	= ARRAY_SIZE(serial2_pads),
-};
-
-static struct omap_board_data serial3_data __initdata = {
-	.id		= 2,
-	.pads		= serial3_pads,
-	.pads_cnt	= ARRAY_SIZE(serial3_pads),
-};
-
-static inline void board_serial_init(void)
-{
-	omap_serial_init_port(&serial1_data);
-	omap_serial_init_port(&serial2_data);
-	omap_serial_init_port(&serial3_data);
-}
 #else
 #define board_mux	NULL
-
-static inline void board_serial_init(void)
-{
-	omap_serial_init();
-}
 #endif
 
 /*

@@ -718,7 +620,7 @@ static void __init omap_3430sdp_init(void)
 	else
 		gpio_pendown = SDP3430_TS_GPIO_IRQ_SDPV1;
 	omap_ads7846_init(1, gpio_pendown, 310, NULL);
-	board_serial_init();
+	omap_serial_init();
 	usb_musb_init(NULL);
 	board_smc91x_init();
 	board_flash_init(sdp_flash_partitions, chip_sel_3430, 0);

82 lines not on this page · raw message

82 lines not on this page · raw message

225 lines not on this page · raw message

index 6d3e228..e7885fc 100644
@@ -627,8 +627,6 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 
 	omap_up.dma_enabled = uart->dma_enabled;
 	omap_up.uartclk = OMAP24XX_BASE_BAUD * 16;
-	omap_up.mapbase = oh->slaves[0]->addr->pa_start;
-	omap_up.membase = omap_hwmod_get_mpu_rt_va(oh);
 	omap_up.flags = UPF_BOOT_AUTOCONF;
 
 	pdata = &omap_up;

index 307cd6f..db9bda9 100644
@@ -59,8 +59,6 @@
 struct omap_uart_port_info {
 	bool			dma_enabled;	/* To specify DMA Mode */
 	unsigned int		uartclk;	/* UART clock rate */
-	void __iomem		*membase;	/* ioremap cookie or NULL */
-	resource_size_t		mapbase;	/* resource base */
 	upf_t			flags;		/* UPF_* flags */
 };
 

index be368cf7..31f0cbf 100644
@@ -1275,8 +1275,14 @@ static int serial_omap_probe(struct platform_device *pdev)
 	up->port.ops = &serial_omap_pops;
 	up->port.line = pdev->id;
 
-	up->port.membase = omap_up_info->membase;
-	up->port.mapbase = omap_up_info->mapbase;
+	up->port.mapbase = mem->start;
+	up->port.membase = ioremap(mem->start, resource_size(mem));
+	if (!up->port.membase) {
+		dev_err(&pdev->dev, "can't ioremap UART\n");
+		ret = -ENOMEM;
+		goto err;
+	}
+
 	up->port.flags = omap_up_info->flags;
 	up->port.uartclk = omap_up_info->uartclk;
 	up->uart_dma.uart_base = mem->start;

index 31f0cbf..a39fc2f 100644
@@ -37,11 +37,14 @@
 #include <linux/clk.h>
 #include <linux/serial_core.h>
 #include <linux/irq.h>
+#include <linux/pm_runtime.h>
 
 #include <plat/dma.h>
 #include <plat/dmtimer.h>
 #include <plat/omap-serial.h>
 
+#define OMAP_UART_AUTOSUSPEND_DELAY -1
+
 static struct uart_omap_port *ui[OMAP_MAX_HSUART_PORTS];
 
 /* Forward declaration of functions */

@@ -102,6 +105,8 @@ static void serial_omap_stop_rxdma(struct uart_omap_port *up)
 		omap_free_dma(up->uart_dma.rx_dma_channel);
 		up->uart_dma.rx_dma_channel = OMAP_UART_DMA_CH_FREE;
 		up->uart_dma.rx_dma_used = false;
+		pm_runtime_mark_last_busy(&up->pdev->dev);
+		pm_runtime_put_autosuspend(&up->pdev->dev);
 	}
 }
 

@@ -110,8 +115,11 @@ static void serial_omap_enable_ms(struct uart_port *port)
 	struct uart_omap_port *up = (struct uart_omap_port *)port;
 
 	dev_dbg(up->port.dev, "serial_omap_enable_ms+%d\n", up->pdev->id);
+
+	pm_runtime_get_sync(&up->pdev->dev);
 	up->ier |= UART_IER_MSI;
 	serial_out(up, UART_IER, up->ier);
+	pm_runtime_put(&up->pdev->dev);
 }
 
 static void serial_omap_stop_tx(struct uart_port *port)

@@ -129,23 +137,32 @@ static void serial_omap_stop_tx(struct uart_port *port)
 		omap_stop_dma(up->uart_dma.tx_dma_channel);
 		omap_free_dma(up->uart_dma.tx_dma_channel);
 		up->uart_dma.tx_dma_channel = OMAP_UART_DMA_CH_FREE;
+		pm_runtime_mark_last_busy(&up->pdev->dev);
+		pm_runtime_put_autosuspend(&up->pdev->dev);
 	}
 
+	pm_runtime_get_sync(&up->pdev->dev);
 	if (up->ier & UART_IER_THRI) {
 		up->ier &= ~UART_IER_THRI;
 		serial_out(up, UART_IER, up->ier);
 	}
+
+	pm_runtime_mark_last_busy(&up->pdev->dev);
+	pm_runtime_put_autosuspend(&up->pdev->dev);
 }
 
 static void serial_omap_stop_rx(struct uart_port *port)
 {
 	struct uart_omap_port *up = (struct uart_omap_port *)port;
 
+	pm_runtime_get_sync(&up->pdev->dev);
 	if (up->use_dma)
 		serial_omap_stop_rxdma(up);
 	up->ier &= ~UART_IER_RLSI;
 	up->port.read_status_mask &= ~UART_LSR_DR;
 	serial_out(up, UART_IER, up->ier);
+	pm_runtime_mark_last_busy(&up->pdev->dev);
+	pm_runtime_put_autosuspend(&up->pdev->dev);
 }
 
 static inline void receive_chars(struct uart_omap_port *up, int *status)

@@ -262,7 +279,10 @@ static void serial_omap_start_tx(struct uart_port *port)
 	int ret = 0;
 
 	if (!up->use_dma) {
+		pm_runtime_get_sync(&up->pdev->dev);
 		serial_omap_enable_ier_thri(up);
+		pm_runtime_mark_last_busy(&up->pdev->dev);
+		pm_runtime_put_autosuspend(&up->pdev->dev);
 		return;
 	}
 

@@ -272,6 +292,7 @@ static void serial_omap_start_tx(struct uart_port *port)
 	xmit = &up->port.state->xmit;
 
 	if (up->uart_dma.tx_dma_channel == OMAP_UART_DMA_CH_FREE) {
+		pm_runtime_get_sync(&up->pdev->dev);
 		ret = omap_request_dma(up->uart_dma.uart_dma_tx,
 				"UART Tx DMA",
 				(void *)uart_tx_dma_callback, up,

@@ -354,9 +375,13 @@ static inline irqreturn_t serial_omap_irq(int irq, void *dev_id)
 	unsigned int iir, lsr;
 	unsigned long flags;
 
+	pm_runtime_get_sync(&up->pdev->dev);
 	iir = serial_in(up, UART_IIR);
-	if (iir & UART_IIR_NO_INT)
+	if (iir & UART_IIR_NO_INT) {
+		pm_runtime_mark_last_busy(&up->pdev->dev);
+		pm_runtime_put_autosuspend(&up->pdev->dev);
 		return IRQ_NONE;
+	}
 
 	spin_lock_irqsave(&up->port.lock, flags);
 	lsr = serial_in(up, UART_LSR);

@@ -378,6 +403,9 @@ static inline irqreturn_t serial_omap_irq(int irq, void *dev_id)
 		transmit_chars(up);
 
 	spin_unlock_irqrestore(&up->port.lock, flags);
+	pm_runtime_mark_last_busy(&up->pdev->dev);
+	pm_runtime_put_autosuspend(&up->pdev->dev);
+
 	up->port_activity = jiffies;
 	return IRQ_HANDLED;
 }

@@ -388,11 +416,12 @@ static unsigned int serial_omap_tx_empty(struct uart_port *port)
 	unsigned long flags = 0;
 	unsigned int ret = 0;
 
+	pm_runtime_get_sync(&up->pdev->dev);
 	dev_dbg(up->port.dev, "serial_omap_tx_empty+%d\n", up->pdev->id);
 	spin_lock_irqsave(&up->port.lock, flags);
 	ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
 	spin_unlock_irqrestore(&up->port.lock, flags);
-
+	pm_runtime_put(&up->pdev->dev);
 	return ret;
 }
 

@@ -402,7 +431,10 @@ static unsigned int serial_omap_get_mctrl(struct uart_port *port)
 	unsigned char status;
 	unsigned int ret = 0;
 
+	pm_runtime_get_sync(&up->pdev->dev);
 	status = check_modem_status(up);
+	pm_runtime_put(&up->pdev->dev);
+
 	dev_dbg(up->port.dev, "serial_omap_get_mctrl+%d\n", up->pdev->id);
 
 	if (status & UART_MSR_DCD)

@@ -433,8 +465,10 @@ static void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl)
 	if (mctrl & TIOCM_LOOP)
 		mcr |= UART_MCR_LOOP;
 
+	pm_runtime_get_sync(&up->pdev->dev);
 	mcr |= up->mcr;
 	serial_out(up, UART_MCR, mcr);
+	pm_runtime_put(&up->pdev->dev);
 }
 
 static void serial_omap_break_ctl(struct uart_port *port, int break_state)

@@ -443,6 +477,7 @@ static void serial_omap_break_ctl(struct uart_port *port, int break_state)
 	unsigned long flags = 0;
 
 	dev_dbg(up->port.dev, "serial_omap_break_ctl+%d\n", up->pdev->id);
+	pm_runtime_get_sync(&up->pdev->dev);
 	spin_lock_irqsave(&up->port.lock, flags);
 	if (break_state == -1)
 		up->lcr |= UART_LCR_SBC;

@@ -450,6 +485,7 @@ static void serial_omap_break_ctl(struct uart_port *port, int break_state)
 		up->lcr &= ~UART_LCR_SBC;
 	serial_out(up, UART_LCR, up->lcr);
 	spin_unlock_irqrestore(&up->port.lock, flags);
+	pm_runtime_put(&up->pdev->dev);
 }
 
 static int serial_omap_startup(struct uart_port *port)

@@ -468,6 +504,7 @@ static int serial_omap_startup(struct uart_port *port)
 
 	dev_dbg(up->port.dev, "serial_omap_startup+%d\n", up->pdev->id);
 
+	pm_runtime_get_sync(&up->pdev->dev);
 	/*
 	 * Clear the FIFO buffers and disable them.
 	 * (they will be reenabled in set_termios())

@@ -523,6 +560,8 @@ static int serial_omap_startup(struct uart_port *port)
 	/* Enable module level wake up */
 	serial_out(up, UART_OMAP_WER, OMAP_UART_WER_MOD_WKUP);
 
+	pm_runtime_mark_last_busy(&up->pdev->dev);
+	pm_runtime_put_autosuspend(&up->pdev->dev);
 	up->port_activity = jiffies;
 	return 0;
 }

@@ -533,6 +572,8 @@ static void serial_omap_shutdown(struct uart_port *port)
 	unsigned long flags = 0;
 
 	dev_dbg(up->port.dev, "serial_omap_shutdown+%d\n", up->pdev->id);
+
+	pm_runtime_get_sync(&up->pdev->dev);
 	/*
 	 * Disable interrupts from this port
 	 */

@@ -566,6 +607,11 @@ static void serial_omap_shutdown(struct uart_port *port)
 			up->uart_dma.rx_buf_dma_phys);
 		up->uart_dma.rx_buf = NULL;
 	}
+
+	if (!device_may_wakeup(&up->pdev->dev))
+		pm_runtime_allow(&up->pdev->dev);
+
+	pm_runtime_put(&up->pdev->dev);
 	free_irq(up->port.irq, up);
 }
 

@@ -680,6 +726,7 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
 	 * Ok, we're now changing the port state. Do it with
 	 * interrupts disabled.
 	 */
+	pm_runtime_get_sync(&up->pdev->dev);
 	spin_lock_irqsave(&up->port.lock, flags);
 
 	/*

@@ -809,6 +856,7 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
 	serial_omap_configure_xonxoff(up, termios);
 
 	spin_unlock_irqrestore(&up->port.lock, flags);
+	pm_runtime_put(&up->pdev->dev);
 	dev_dbg(up->port.dev, "serial_omap_set_termios+%d\n", up->pdev->id);
 }
 

@@ -820,6 +868,8 @@ serial_omap_pm(struct uart_port *port, unsigned int state,
 	unsigned char efr;
 
 	dev_dbg(up->port.dev, "serial_omap_pm+%d\n", up->pdev->id);
+
+	pm_runtime_get_sync(&up->pdev->dev);
 	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
 	efr = serial_in(up, UART_EFR);
 	serial_out(up, UART_EFR, efr | UART_EFR_ECB);

@@ -829,6 +879,11 @@ serial_omap_pm(struct uart_port *port, unsigned int state,
 	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
 	serial_out(up, UART_EFR, efr);
 	serial_out(up, UART_LCR, 0);
+
+	if (!state && !device_may_wakeup(&up->pdev->dev))
+		pm_runtime_forbid(&up->pdev->dev);
+
+	pm_runtime_put(&up->pdev->dev);
 }
 
 static void serial_omap_release_port(struct uart_port *port)

@@ -906,19 +961,26 @@ static inline void wait_for_xmitr(struct uart_omap_port *up)
 static void serial_omap_poll_put_char(struct uart_port *port, unsigned char ch)
 {
 	struct uart_omap_port *up = (struct uart_omap_port *)port;
+
+	pm_runtime_get_sync(&up->pdev->dev);
 	wait_for_xmitr(up);
 	serial_out(up, UART_TX, ch);
+	pm_runtime_put(&up->pdev->dev);
 }
 
 static int serial_omap_poll_get_char(struct uart_port *port)
 {
 	struct uart_omap_port *up = (struct uart_omap_port *)port;
-	unsigned int status = serial_in(up, UART_LSR);
+	unsigned int status;
 
+	pm_runtime_get_sync(&up->pdev->dev);
+	status = serial_in(up, UART_LSR);
 	if (!(status & UART_LSR_DR))
 		return NO_POLL_CHAR;
 
-	return serial_in(up, UART_RX);
+	status = serial_in(up, UART_RX);
+	pm_runtime_put(&up->pdev->dev);
+	return status;
 }
 
 #endif /* CONFIG_CONSOLE_POLL */

@@ -946,6 +1008,8 @@ serial_omap_console_write(struct console *co, const char *s,
 	unsigned int ier;
 	int locked = 1;
 
+	pm_runtime_get_sync(&up->pdev->dev);
+
 	local_irq_save(flags);
 	if (up->port.sysrq)
 		locked = 0;

@@ -978,6 +1042,8 @@ serial_omap_console_write(struct console *co, const char *s,
 	if (up->msr_saved_flags)
 		check_modem_status(up);
 
+	pm_runtime_mark_last_busy(&up->pdev->dev);
+	pm_runtime_put_autosuspend(&up->pdev->dev);
 	if (locked)
 		spin_unlock(&up->port.lock);
 	local_irq_restore(flags);

@@ -1060,24 +1126,25 @@ static struct uart_driver serial_omap_reg = {
 	.cons		= OMAP_CONSOLE,
 };
 
-static int
-serial_omap_suspend(struct platform_device *pdev, pm_message_t state)
+#ifdef CONFIG_SUSPEND
+static int serial_omap_suspend(struct device *dev)
 {
-	struct uart_omap_port *up = platform_get_drvdata(pdev);
+	struct uart_omap_port *up = dev_get_drvdata(dev);
 
 	if (up)
 		uart_suspend_port(&serial_omap_reg, &up->port);
 	return 0;
 }
 
-static int serial_omap_resume(struct platform_device *dev)
+static int serial_omap_resume(struct device *dev)
 {
-	struct uart_omap_port *up = platform_get_drvdata(dev);
+	struct uart_omap_port *up = dev_get_drvdata(dev);
 
 	if (up)
 		uart_resume_port(&serial_omap_reg, &up->port);
 	return 0;
 }
+#endif
 
 static void serial_omap_rx_timeout(unsigned long uart_no)
 {

@@ -1135,6 +1202,7 @@ static int serial_omap_start_rxdma(struct uart_omap_port *up)
 	int ret = 0;
 
 	if (up->uart_dma.rx_dma_channel == -1) {
+		pm_runtime_get_sync(&up->pdev->dev);
 		ret = omap_request_dma(up->uart_dma.uart_dma_rx,
 				"UART Rx DMA",
 				(void *)uart_rx_dma_callback, up,

@@ -1299,6 +1367,14 @@ static int serial_omap_probe(struct platform_device *pdev)
 		up->uart_dma.rx_dma_channel = OMAP_UART_DMA_CH_FREE;
 	}
 
+	pm_runtime_use_autosuspend(&pdev->dev);
+	pm_runtime_set_autosuspend_delay(&pdev->dev,
+			OMAP_UART_AUTOSUSPEND_DELAY);
+
+	pm_runtime_irq_safe(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+	pm_runtime_get_sync(&pdev->dev);
+
 	ui[pdev->id] = up;
 	serial_omap_add_console_port(up);
 

@@ -1306,6 +1382,7 @@ static int serial_omap_probe(struct platform_device *pdev)
 	if (ret != 0)
 		goto do_release_region;
 
+	pm_runtime_put(&pdev->dev);
 	platform_set_drvdata(pdev, up);
 	return 0;
 err:

@@ -1320,22 +1397,40 @@ static int serial_omap_remove(struct platform_device *dev)
 {
 	struct uart_omap_port *up = platform_get_drvdata(dev);
 
-	platform_set_drvdata(dev, NULL);
 	if (up) {
+		pm_runtime_disable(&up->pdev->dev);
 		uart_remove_one_port(&serial_omap_reg, &up->port);
 		kfree(up);
 	}
+
+	platform_set_drvdata(dev, NULL);
+	return 0;
+}
+
+#ifdef CONFIG_PM_RUNTIME
+static int serial_omap_runtime_suspend(struct device *dev)
+{
 	return 0;
 }
 
+static int serial_omap_runtime_resume(struct device *dev)
+{
+	return 0;
+}
+#endif
+
+static const struct dev_pm_ops serial_omap_dev_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(serial_omap_suspend, serial_omap_resume)
+	SET_RUNTIME_PM_OPS(serial_omap_runtime_suspend,
+				serial_omap_runtime_resume, NULL)
+};
+
 static struct platform_driver serial_omap_driver = {
 	.probe          = serial_omap_probe,
 	.remove         = serial_omap_remove,
-
-	.suspend	= serial_omap_suspend,
-	.resume		= serial_omap_resume,
 	.driver		= {
 		.name	= DRIVER_NAME,
+		.pm	= &serial_omap_dev_pm_ops,
 	},
 };
 

index e7885fc..cfe6055 100644
@@ -41,8 +41,6 @@
 #include "control.h"
 #include "mux.h"
 
-#define UART_OMAP_WER		0x17	/* Wake-up enable register */
-
 #define UART_ERRATA_i202_MDR1_ACCESS	(0x1 << 1)
 
 /*

@@ -66,27 +64,11 @@ struct omap_uart_state {
 
 	int clocked;
 
-	int regshift;
-	void __iomem *membase;
-	resource_size_t mapbase;
-
 	struct list_head node;
 	struct omap_hwmod *oh;
 	struct platform_device *pdev;
 
 	u32 errata;
-#if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
-	int context_valid;
-
-	/* Registers to be saved/restored for OFF-mode */
-	u16 dll;
-	u16 dlh;
-	u16 ier;
-	u16 sysc;
-	u16 scr;
-	u16 wer;
-	u16 mcr;
-#endif
 };
 
 static LIST_HEAD(uart_list);

@@ -114,34 +96,6 @@ static struct omap_device_pm_latency omap_uart_latency[] = {
 	},
 };
 
-static inline unsigned int __serial_read_reg(struct uart_port *up,
-					     int offset)
-{
-	offset <<= up->regshift;
-	return (unsigned int)__raw_readb(up->membase + offset);
-}
-
-static inline unsigned int serial_read_reg(struct omap_uart_state *uart,
-					   int offset)
-{
-	offset <<= uart->regshift;
-	return (unsigned int)__raw_readb(uart->membase + offset);
-}
-
-static inline void __serial_write_reg(struct uart_port *up, int offset,
-		int value)
-{
-	offset <<= up->regshift;
-	__raw_writeb(value, up->membase + offset);
-}
-
-static inline void serial_write_reg(struct omap_uart_state *uart, int offset,
-				    int value)
-{
-	offset <<= uart->regshift;
-	__raw_writeb(value, uart->membase + offset);
-}
-
 /*
  * Internal UARTs need to be initialized for the 8250 autoconfig to work
  * properly. Note that the TX watermark initialization may not be needed

@@ -192,75 +146,6 @@ static void omap_uart_mdr1_errataset(struct omap_uart_state *uart, u8 mdr1_val,
 	}
 }
 
-static void omap_uart_save_context(struct omap_uart_state *uart)
-{
-	u16 lcr = 0;
-
-	if (!enable_off_mode)
-		return;
-
-	lcr = serial_read_reg(uart, UART_LCR);
-	serial_write_reg(uart, UART_LCR, UART_LCR_CONF_MODE_B);
-	uart->dll = serial_read_reg(uart, UART_DLL);
-	uart->dlh = serial_read_reg(uart, UART_DLM);
-	serial_write_reg(uart, UART_LCR, lcr);
-	uart->ier = serial_read_reg(uart, UART_IER);
-	uart->sysc = serial_read_reg(uart, UART_OMAP_SYSC);
-	uart->scr = serial_read_reg(uart, UART_OMAP_SCR);
-	uart->wer = serial_read_reg(uart, UART_OMAP_WER);
-	serial_write_reg(uart, UART_LCR, UART_LCR_CONF_MODE_A);
-	uart->mcr = serial_read_reg(uart, UART_MCR);
-	serial_write_reg(uart, UART_LCR, lcr);
-
-	uart->context_valid = 1;
-}
-
-static void omap_uart_restore_context(struct omap_uart_state *uart)
-{
-	u16 efr = 0;
-
-	if (!enable_off_mode)
-		return;
-
-	if (!uart->context_valid)
-		return;
-
-	uart->context_valid = 0;
-
-	if (uart->errata & UART_ERRATA_i202_MDR1_ACCESS)
-		omap_uart_mdr1_errataset(uart, UART_OMAP_MDR1_DISABLE, 0xA0);
-	else
-		serial_write_reg(uart, UART_OMAP_MDR1, UART_OMAP_MDR1_DISABLE);
-
-	serial_write_reg(uart, UART_LCR, UART_LCR_CONF_MODE_B);
-	efr = serial_read_reg(uart, UART_EFR);
-	serial_write_reg(uart, UART_EFR, UART_EFR_ECB);
-	serial_write_reg(uart, UART_LCR, 0x0); /* Operational mode */
-	serial_write_reg(uart, UART_IER, 0x0);
-	serial_write_reg(uart, UART_LCR, UART_LCR_CONF_MODE_B);
-	serial_write_reg(uart, UART_DLL, uart->dll);
-	serial_write_reg(uart, UART_DLM, uart->dlh);
-	serial_write_reg(uart, UART_LCR, 0x0); /* Operational mode */
-	serial_write_reg(uart, UART_IER, uart->ier);
-	serial_write_reg(uart, UART_LCR, UART_LCR_CONF_MODE_A);
-	serial_write_reg(uart, UART_MCR, uart->mcr);
-	serial_write_reg(uart, UART_LCR, UART_LCR_CONF_MODE_B);
-	serial_write_reg(uart, UART_EFR, efr);
-	serial_write_reg(uart, UART_LCR, UART_LCR_WLEN8);
-	serial_write_reg(uart, UART_OMAP_SCR, uart->scr);
-	serial_write_reg(uart, UART_OMAP_WER, uart->wer);
-	serial_write_reg(uart, UART_OMAP_SYSC, uart->sysc);
-
-	if (uart->errata & UART_ERRATA_i202_MDR1_ACCESS)
-		omap_uart_mdr1_errataset(uart, UART_OMAP_MDR1_16X_MODE, 0xA1);
-	else
-		/* UART 16x mode */
-		serial_write_reg(uart, UART_OMAP_MDR1,
-				UART_OMAP_MDR1_16X_MODE);
-}
-#else
-static inline void omap_uart_save_context(struct omap_uart_state *uart) {}
-static inline void omap_uart_restore_context(struct omap_uart_state *uart) {}
 #endif /* CONFIG_PM && CONFIG_ARCH_OMAP3 */
 
 static inline void omap_uart_enable_clocks(struct omap_uart_state *uart)

@@ -644,9 +529,6 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 	omap_device_disable_idle_on_suspend(pdev);
 	oh->mux = omap_hwmod_mux_init(bdata->pads, bdata->pads_cnt);
 
-	uart->regshift = 2;
-	uart->mapbase = oh->slaves[0]->addr->pa_start;
-	uart->membase = omap_hwmod_get_mpu_rt_va(oh);
 	uart->pdev = pdev;
 
 	oh->dev_attr = uart;

index a39fc2f..0d87985 100644
@@ -1407,6 +1407,25 @@ static int serial_omap_remove(struct platform_device *dev)
 	return 0;
 }
 
+static void serial_omap_restore_context(struct uart_omap_port *up)
+{
+	serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_DISABLE);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /* Config B mode */
+	serial_out(up, UART_EFR, UART_EFR_ECB);
+	serial_out(up, UART_LCR, 0x0); /* Operational mode */
+	serial_out(up, UART_IER, 0x0);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /* Config B mode */
+	serial_out(up, UART_LCR, 0x0); /* Operational mode */
+	serial_out(up, UART_IER, up->ier);
+	serial_out(up, UART_FCR, up->fcr);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
+	serial_out(up, UART_MCR, up->mcr);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /* Config B mode */
+	serial_out(up, UART_EFR, up->efr);
+	serial_out(up, UART_LCR, up->lcr);
+	serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_16X_MODE);
+}
+
 #ifdef CONFIG_PM_RUNTIME
 static int serial_omap_runtime_suspend(struct device *dev)
 {

@@ -1415,6 +1434,11 @@ static int serial_omap_runtime_suspend(struct device *dev)
 
 static int serial_omap_runtime_resume(struct device *dev)
 {
+	struct uart_omap_port *up = dev_get_drvdata(dev);
+
+	if (up)
+		serial_omap_restore_context(up);
+
 	return 0;
 }
 #endif

index db9bda9..70e7738 100644
@@ -97,6 +97,10 @@ struct uart_omap_port {
 	unsigned char		mcr;
 	unsigned char		fcr;
 	unsigned char		efr;
+	unsigned char		dll;
+	unsigned char		dlh;
+	unsigned char		mdr1;
+	unsigned char		scr;
 
 	int			use_dma;
 	/*

132 lines not on this page · raw message

index cfe6055..7dd75f1 100644
@@ -96,19 +96,6 @@ static struct omap_device_pm_latency omap_uart_latency[] = {
 	},
 };
 
-/*
- * Internal UARTs need to be initialized for the 8250 autoconfig to work
- * properly. Note that the TX watermark initialization may not be needed
- * once the 8250.c watermark handling code is merged.
- */
-
-static inline void __init omap_uart_reset(struct omap_uart_state *uart)
-{
-	serial_write_reg(uart, UART_OMAP_MDR1, UART_OMAP_MDR1_DISABLE);
-	serial_write_reg(uart, UART_OMAP_SCR, 0x08);
-	serial_write_reg(uart, UART_OMAP_MDR1, UART_OMAP_MDR1_16X_MODE);
-}
-
 #if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP3)
 
 /*

@@ -544,7 +531,6 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 
 	omap_device_enable(uart->pdev);
 	omap_uart_idle_init(uart);
-	omap_uart_reset(uart);
 	omap_hwmod_enable_wakeup(uart->oh);
 	omap_device_idle(uart->pdev);
 

index 70e7738..5b913c7 100644
@@ -33,6 +33,8 @@
 
 #define OMAP_MODE13X_SPEED	230400
 
+#define OMAP_UART_SCR_TX_EMPTY	0x08
+
 /* WER = 0x7F
  * Enable module level wakeup in WER reg
  */

index 192fc8b..a7fdf94 100644
@@ -773,6 +773,7 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
 	serial_out(up, UART_IER, up->ier);
 	serial_out(up, UART_LCR, cval);		/* reset DLAB */
 	up->lcr = cval;
+	up->scr = OMAP_UART_SCR_TX_EMPTY;
 
 	/* FIFOs and DMA Settings */
 

index 7dd75f1..f220c84 100644
@@ -33,6 +33,7 @@
 #include <plat/dma.h>
 #include <plat/omap_hwmod.h>
 #include <plat/omap_device.h>
+#include <plat/omap-pm.h>
 
 #include "prm2xxx_3xxx.h"
 #include "pm.h"

@@ -500,6 +501,7 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 	omap_up.dma_enabled = uart->dma_enabled;
 	omap_up.uartclk = OMAP24XX_BASE_BAUD * 16;
 	omap_up.flags = UPF_BOOT_AUTOCONF;
+	omap_up.get_context_loss_count = omap_pm_get_dev_context_loss_count;
 
 	pdata = &omap_up;
 	pdata_size = sizeof(struct omap_uart_port_info);

index 5b913c7..f265bb9 100644
@@ -62,6 +62,8 @@ struct omap_uart_port_info {
 	bool			dma_enabled;	/* To specify DMA Mode */
 	unsigned int		uartclk;	/* UART clock rate */
 	upf_t			flags;		/* UPF_* flags */
+
+	u32 (*get_context_loss_count)(struct device *);
 };
 
 struct uart_omap_dma {

@@ -114,6 +116,7 @@ struct uart_omap_port {
 	unsigned char		msr_saved_flags;
 	char			name[20];
 	unsigned long		port_activity;
+	u32			context_loss_cnt;
 };
 
 #endif /* __OMAP_SERIAL_H__ */

index a7fdf94..289fa7b 100644
@@ -1439,15 +1439,31 @@ static void serial_omap_restore_context(struct uart_omap_port *up)
 #ifdef CONFIG_PM_RUNTIME
 static int serial_omap_runtime_suspend(struct device *dev)
 {
+	struct uart_omap_port *up = dev_get_drvdata(dev);
+	struct omap_uart_port_info *pdata = dev->platform_data;
+
+	if (!up)
+		return -EINVAL;
+
+	if (pdata->get_context_loss_count)
+		up->context_loss_cnt = pdata->get_context_loss_count(dev);
+
 	return 0;
 }
 
 static int serial_omap_runtime_resume(struct device *dev)
 {
 	struct uart_omap_port *up = dev_get_drvdata(dev);
+	struct omap_uart_port_info *pdata = dev->platform_data;
 
-	if (up)
-		serial_omap_restore_context(up);
+	if (up) {
+		if (pdata->get_context_loss_count) {
+			u32 loss_cnt = pdata->get_context_loss_count(dev);
+
+			if (up->context_loss_cnt != loss_cnt)
+				serial_omap_restore_context(up);
+		}
+	}
 
 	return 0;
 }

index f220c84..8c6dc85 100644
@@ -42,8 +42,6 @@
 #include "control.h"
 #include "mux.h"
 
-#define UART_ERRATA_i202_MDR1_ACCESS	(0x1 << 1)
-
 /*
  * NOTE: By default the serial timeout is disabled as it causes lost characters
  * over the serial ports. This means that the UART clocks will stay on until

@@ -61,15 +59,12 @@ struct omap_uart_state {
 	void __iomem *wk_st;
 	void __iomem *wk_en;
 	u32 wk_mask;
-	u32 dma_enabled;
 
 	int clocked;
 
 	struct list_head node;
 	struct omap_hwmod *oh;
 	struct platform_device *pdev;
-
-	u32 errata;
 };
 
 static LIST_HEAD(uart_list);

@@ -97,45 +92,6 @@ static struct omap_device_pm_latency omap_uart_latency[] = {
 	},
 };
 
-#if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP3)
-
-/*
- * Work Around for Errata i202 (3430 - 1.12, 3630 - 1.6)
- * The access to uart register after MDR1 Access
- * causes UART to corrupt data.
- *
- * Need a delay =
- * 5 L4 clock cycles + 5 UART functional clock cycle (@48MHz = ~0.2uS)
- * give 10 times as much
- */
-static void omap_uart_mdr1_errataset(struct omap_uart_state *uart, u8 mdr1_val,
-		u8 fcr_val)
-{
-	u8 timeout = 255;
-
-	serial_write_reg(uart, UART_OMAP_MDR1, mdr1_val);
-	udelay(2);
-	serial_write_reg(uart, UART_FCR, fcr_val | UART_FCR_CLEAR_XMIT |
-			UART_FCR_CLEAR_RCVR);
-	/*
-	 * Wait for FIFO to empty: when empty, RX_FIFO_E bit is 0 and
-	 * TX_FIFO_E bit is 1.
-	 */
-	while (UART_LSR_THRE != (serial_read_reg(uart, UART_LSR) &
-				(UART_LSR_THRE | UART_LSR_DR))) {
-		timeout--;
-		if (!timeout) {
-			/* Should *never* happen. we warn and carry on */
-			dev_crit(&uart->pdev->dev, "Errata i202: timedout %x\n",
-			serial_read_reg(uart, UART_LSR));
-			break;
-		}
-		udelay(1);
-	}
-}
-
-#endif /* CONFIG_PM && CONFIG_ARCH_OMAP3 */
-
 static inline void omap_uart_enable_clocks(struct omap_uart_state *uart)
 {
 	if (uart->clocked)

@@ -178,27 +134,6 @@ static void omap_uart_disable_wakeup(struct omap_uart_state *uart)
 	}
 }
 
-static void omap_uart_smart_idle_enable(struct omap_uart_state *uart,
-					       int enable)
-{
-	u8 idlemode;
-
-	if (enable) {
-		/**
-		 * Errata 2.15: [UART]:Cannot Acknowledge Idle Requests
-		 * in Smartidle Mode When Configured for DMA Operations.
-		 */
-		if (uart->dma_enabled)
-			idlemode = HWMOD_IDLEMODE_FORCE;
-		else
-			idlemode = HWMOD_IDLEMODE_SMART;
-	} else {
-		idlemode = HWMOD_IDLEMODE_NO;
-	}
-
-	omap_hwmod_set_slave_idlemode(uart->oh, idlemode);
-}
-
 static void omap_uart_block_sleep(struct omap_uart_state *uart)
 {
 	omap_uart_enable_clocks(uart);

@@ -289,7 +224,28 @@ static void omap_uart_idle_init(struct omap_uart_state *uart)
 	}
 }
 
+/*
+ * Errata i291: [UART]:Cannot Acknowledge Idle Requests
+ * in Smartidle Mode When Configured for DMA Operations.
+ * WA: configure uart in force idle mode.
+ */
+static void omap_uart_set_noidle(struct platform_device *pdev)
+{
+	struct omap_device *od = to_omap_device(pdev);
+
+	omap_hwmod_set_slave_idlemode(od->hwmods[0], HWMOD_IDLEMODE_NO);
+}
+
+static void omap_uart_set_forceidle(struct platform_device *pdev)
+{
+	struct omap_device *od = to_omap_device(pdev);
+
+	omap_hwmod_set_slave_idlemode(od->hwmods[0], HWMOD_IDLEMODE_FORCE);
+}
+
 #else
+static void omap_uart_set_noidle(struct platform_device *pdev) {}
+static void omap_uart_set_forceidle(struct platform_device *pdev) {}
 static void omap_uart_block_sleep(struct omap_uart_state *uart)
 {
 	/* Needed to enable UART clocks when built without CONFIG_PM */

@@ -495,13 +451,18 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 			break;
 
 	oh = uart->oh;
-	uart->dma_enabled = 0;
 	name = DRIVER_NAME;
 
 	omap_up.dma_enabled = uart->dma_enabled;
 	omap_up.uartclk = OMAP24XX_BASE_BAUD * 16;
 	omap_up.flags = UPF_BOOT_AUTOCONF;
 	omap_up.get_context_loss_count = omap_pm_get_dev_context_loss_count;
+	omap_up.set_forceidle = omap_uart_set_forceidle;
+	omap_up.set_noidle = omap_uart_set_noidle;
+
+	/* Enable the MDR1 errata for OMAP3 */
+	if (cpu_is_omap34xx() && !cpu_is_ti816x())
+		omap_up.errata |= UART_ERRATA_i202_MDR1_ACCESS;
 
 	pdata = &omap_up;
 	pdata_size = sizeof(struct omap_uart_port_info);

@@ -542,10 +503,6 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 	if (((cpu_is_omap34xx() || cpu_is_omap44xx()) && bdata->pads) ||
 		(pdata->wk_en && pdata->wk_mask))
 		device_init_wakeup(&pdev->dev, true);
-
-	/* Enable the MDR1 errata for OMAP3 */
-	if (cpu_is_omap34xx() && !cpu_is_ti816x())
-		uart->errata |= UART_ERRATA_i202_MDR1_ACCESS;
 }
 
 /**

index f265bb9..f9baf01 100644
@@ -58,12 +58,17 @@
 
 #define MSR_SAVE_FLAGS		UART_MSR_ANY_DELTA
 
+#define UART_ERRATA_i202_MDR1_ACCESS	(0x1 << 1)
+
 struct omap_uart_port_info {
 	bool			dma_enabled;	/* To specify DMA Mode */
 	unsigned int		uartclk;	/* UART clock rate */
 	upf_t			flags;		/* UPF_* flags */
+	u32			errata;
 
 	u32 (*get_context_loss_count)(struct device *);
+	void (*set_forceidle)(struct platform_device *);
+	void (*set_noidle)(struct platform_device *);
 };
 
 struct uart_omap_dma {

@@ -117,6 +122,7 @@ struct uart_omap_port {
 	char			name[20];
 	unsigned long		port_activity;
 	u32			context_loss_cnt;
+	u32			errata;
 };
 
 #endif /* __OMAP_SERIAL_H__ */

116 lines not on this page · raw message

index 6b3f0bd..66c8360 100644
@@ -56,8 +56,6 @@ struct omap_uart_state {
 	int num;
 	int can_sleep;
 
-	int clocked;
-
 	struct list_head node;
 	struct omap_hwmod *oh;
 	struct platform_device *pdev;

@@ -88,36 +86,8 @@ static struct omap_device_pm_latency omap_uart_latency[] = {
 	},
 };
 
-static inline void omap_uart_enable_clocks(struct omap_uart_state *uart)
-{
-	if (uart->clocked)
-		return;
-
-	omap_device_enable(uart->pdev);
-	uart->clocked = 1;
-	omap_uart_restore_context(uart);
-}
-
 #ifdef CONFIG_PM
 
-static inline void omap_uart_disable_clocks(struct omap_uart_state *uart)
-{
-	if (!uart->clocked)
-		return;
-
-	omap_uart_save_context(uart);
-	uart->clocked = 0;
-	omap_device_idle(uart->pdev);
-}
-
-static void omap_uart_block_sleep(struct omap_uart_state *uart)
-{
-	omap_uart_enable_clocks(uart);
-
-	omap_uart_smart_idle_enable(uart, 0);
-	uart->can_sleep = 0;
-}
-
 int omap_uart_can_sleep(void)
 {
 	struct omap_uart_state *uart;

@@ -176,11 +146,6 @@ static void omap_uart_enable_wakeup(struct platform_device *pdev, bool enable)
 {}
 static void omap_uart_set_noidle(struct platform_device *pdev) {}
 static void omap_uart_set_forceidle(struct platform_device *pdev) {}
-static void omap_uart_block_sleep(struct omap_uart_state *uart)
-{
-	/* Needed to enable UART clocks when built without CONFIG_PM */
-	omap_uart_enable_clocks(uart);
-}
 #endif /* CONFIG_PM */
 
 #ifdef CONFIG_OMAP_MUX

@@ -426,7 +391,6 @@ void __init omap_serial_init_port(struct omap_board_data *bdata)
 	omap_device_enable(uart->pdev);
 	omap_device_idle(uart->pdev);
 
-	omap_uart_block_sleep(uart);
 	console_unlock();
 
 	if ((cpu_is_omap34xx() || cpu_is_omap44xx()) && bdata->pads)