video: s3c2410: fix checkpatch error and warnings

This patch fixes the checkpatch errors listed below:

ERROR: do not initialise statics to 0 or NULL
WARNING: Use #include <linux/io.h> instead of <asm/io.h>
WARNING: braces {} are not necessary for single statement blocks
WARNING: braces {} are not necessary for any arm of this statement
WARNING: static char array declaration should probably be static const char
WARNING: line over 80 characters
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt

Signed-off-by Jingoo Han <[email protected]>

---
 drivers/video/s3c2410fb.c |   29 +++++++++++++++--------------
 1 files changed, 15 insertions(+), 14 deletions(-)

drivers/video/s3c2410fb.c +15 -14

index ee4c0df..77f34c6 100644
@@ -26,8 +26,8 @@
 #include <linux/platform_device.h>
 #include <linux/clk.h>
 #include <linux/cpufreq.h>
+#include <linux/io.h>
 
-#include <asm/io.h>
 #include <asm/div64.h>
 
 #include <asm/mach/map.h>

@@ -45,10 +45,10 @@
 #ifdef CONFIG_FB_S3C2410_DEBUG
 static int debug	= 1;
 #else
-static int debug	= 0;
+static int debug;
 #endif
 
-#define dprintk(msg...)	if (debug) { printk(KERN_DEBUG "s3c2410fb: " msg); }
+#define dprintk(msg...)	if (debug) printk(KERN_DEBUG "s3c2410fb: " msg);
 
 /* useful functions */
 

@@ -567,11 +567,10 @@ static int s3c2410fb_blank(int blank_mode, struct fb_info *info)
 
 	tpal_reg += is_s3c2412(fbi) ? S3C2412_TPAL : S3C2410_TPAL;
 
-	if (blank_mode = FB_BLANK_POWERDOWN) {
+	if (blank_mode = FB_BLANK_POWERDOWN)
 		s3c2410fb_lcd_enable(fbi, 0);
-	} else {
+	else
 		s3c2410fb_lcd_enable(fbi, 1);
-	}
 
 	if (blank_mode = FB_BLANK_UNBLANK)
 		writel(0x0, tpal_reg);

@@ -812,7 +811,7 @@ static inline void s3c2410fb_cpufreq_deregister(struct s3c2410fb_info *info)
 #endif
 
 
-static char driver_name[] = "s3c2410fb";
+static const char driver_name[] = "s3c2410fb";
 
 static int __devinit s3c24xxfb_probe(struct platform_device *pdev,
 				  enum s3c_drv_type drv_type)

@@ -881,7 +880,10 @@ static int __devinit s3c24xxfb_probe(struct platform_device *pdev,
 		goto release_mem;
 	}
 
-	info->irq_base = info->io + ((drv_type = DRV_S3C2412) ? S3C2412_LCDINTBASE : S3C2410_LCDINTBASE);
+	if (drv_type = DRV_S3C2412)
+		info->irq_base = info->io + S3C2412_LCDINTBASE;
+	else
+		info->irq_base = info->io + S3C2410_LCDINTBASE;
 
 	dprintk("devinit\n");
 

@@ -927,7 +929,7 @@ static int __devinit s3c24xxfb_probe(struct platform_device *pdev,
 	clk_enable(info->clk);
 	dprintk("got and enabled clock\n");
 
-	msleep(1);
+	usleep_range(1000, 1000);
 
 	info->clk_rate = clk_get_rate(info->clk);
 

@@ -975,9 +977,8 @@ static int __devinit s3c24xxfb_probe(struct platform_device *pdev,
 
 	/* create device files */
 	ret = device_create_file(&pdev->dev, &dev_attr_debug);
-	if (ret) {
+	if (ret)
 		printk(KERN_ERR "failed to add debug attribute\n");
-	}
 
 	printk(KERN_INFO "fb%d: %s frame buffer device\n",
 		fbinfo->node, fbinfo->fix.id);

@@ -1027,7 +1028,7 @@ static int __devexit s3c2410fb_remove(struct platform_device *pdev)
 	s3c2410fb_cpufreq_deregister(info);
 
 	s3c2410fb_lcd_enable(info, 0);
-	msleep(1);
+	usleep_range(1000, 1000);
 
 	s3c2410fb_unmap_video_memory(fbinfo);
 

@@ -1064,7 +1065,7 @@ static int s3c2410fb_suspend(struct platform_device *dev, pm_message_t state)
 	 * the LCD DMA engine is not going to get back on the bus
 	 * before the clock goes off again (bjd) */
 
-	msleep(1);
+	usleep_range(1000, 1000);
 	clk_disable(info->clk);
 
 	return 0;

@@ -1076,7 +1077,7 @@ static int s3c2410fb_resume(struct platform_device *dev)
 	struct s3c2410fb_info *info = fbinfo->par;
 
 	clk_enable(info->clk);
-	msleep(1);
+	usleep_range(1000, 1000);
 
 	s3c2410fb_init_registers(fbinfo);