at91: drop ide driver in favor of the pata one

Signed-off-by Jean-Christophe PLAGNIOL-VILLARD <[email protected]>

Cc Nicolas Ferre <[email protected]>

Cc linux-ide at vger.kernel.org

Cc "David S. Miller" <[email protected]>

---
 arch/arm/mach-at91/at91sam9260_devices.c |    7 +-
 arch/arm/mach-at91/at91sam9263_devices.c |    6 +-
 drivers/ide/Makefile                     |    1 -
 drivers/ide/at91_ide.c                   |  366 ------------------------------
 4 files changed, 5 insertions(+), 375 deletions(-)
 delete mode 100644 drivers/ide/at91_ide.c

arch/arm/mach-at91/at91sam9260_devices.c +2 -5

index 642ccb6..820e857 100644
@@ -1215,8 +1215,7 @@ void __init at91_add_device_serial(void) {}
  *  CF/IDE
  * -------------------------------------------------------------------- */
 
-#if defined(CONFIG_BLK_DEV_IDE_AT91) || defined(CONFIG_BLK_DEV_IDE_AT91_MODULE) || \
-	defined(CONFIG_PATA_AT91) || defined(CONFIG_PATA_AT91_MODULE) || \
+#if defined(CONFIG_PATA_AT91) || defined(CONFIG_PATA_AT91_MODULE) || \
 	defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE)
 
 static struct at91_cf_data cf0_data;

@@ -1313,10 +1312,8 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 	if (data->flags & AT91_CF_TRUE_IDE)
 #if defined(CONFIG_PATA_AT91) || defined(CONFIG_PATA_AT91_MODULE)
 		pdev->name = "pata_at91";
-#elif defined(CONFIG_BLK_DEV_IDE_AT91) || defined(CONFIG_BLK_DEV_IDE_AT91_MODULE)
-		pdev->name = "at91_ide";
 #else
-#warning "board requires AT91_CF_TRUE_IDE: enable either at91_ide or pata_at91"
+#warning "board requires AT91_CF_TRUE_IDE: enable pata_at91"
 #endif
 	else
 		pdev->name = "at91_cf";

arch/arm/mach-at91/at91sam9263_devices.c +3 -3

index 7b46b27..a61637a 100644
@@ -355,8 +355,8 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
  *  Compact Flash (PCMCIA or IDE)
  * -------------------------------------------------------------------- */
 
-#if defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE) || \
-    defined(CONFIG_BLK_DEV_IDE_AT91) || defined(CONFIG_BLK_DEV_IDE_AT91_MODULE)
+#if defined(CONFIG_PATA_AT91) || defined(CONFIG_PATA_AT91_MODULE) || \
+	defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE)
 
 static struct at91_cf_data cf0_data;
 

@@ -450,7 +450,7 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 	at91_set_A_periph(AT91_PIN_PD9, 0);  /* CFCE2 */
 	at91_set_A_periph(AT91_PIN_PD14, 0); /* CFNRW */
 
-	pdev->name = (data->flags & AT91_CF_TRUE_IDE) ? "at91_ide" : "at91_cf";
+	pdev->name = (data->flags & AT91_CF_TRUE_IDE) ? "pata_at91" : "at91_cf";
 	platform_device_register(pdev);
 }
 #else

drivers/ide/Makefile +0 -1

index 7f879b2..af8d016 100644
@@ -116,4 +116,3 @@ obj-$(CONFIG_BLK_DEV_IDE_AU1XXX)	+= au1xxx-ide.o
 
 obj-$(CONFIG_BLK_DEV_IDE_TX4938)	+= tx4938ide.o
 obj-$(CONFIG_BLK_DEV_IDE_TX4939)	+= tx4939ide.o
-obj-$(CONFIG_BLK_DEV_IDE_AT91)		+= at91_ide.o

drivers/ide/at91_ide.c deleted +0 -366

deleted file mode 100644
index 41d4155..0000000
@@ -1,366 +0,0 @@
-/*
- * IDE host driver for AT91 (SAM9, CAP9, AT572D940HF) Static Memory Controller
- * with Compact Flash True IDE logic
- *
- * Copyright (c) 2008, 2009 Kelvatek Ltd.
- *
- *  This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/ide.h>
-#include <linux/platform_device.h>
-
-#include <mach/board.h>
-#include <asm/gpio.h>
-#include <mach/at91sam9_smc.h>
-
-#define DRV_NAME "at91_ide"
-
-#define perr(fmt, args...) pr_err(DRV_NAME ": " fmt, ##args)
-#define pdbg(fmt, args...) pr_debug("%s " fmt, __func__, ##args)
-
-/*
- * Access to IDE device is possible through EBI Static Memory Controller
- * with Compact Flash logic. For details see EBI and SMC datasheet sections
- * of any microcontroller from AT91SAM9 family.
- *
- * Within SMC chip select address space, lines A[23:21] distinguish Compact
- * Flash modes (I/O, common memory, attribute memory, True IDE). IDE modes are:
- *   0x00c0000 - True IDE
- *   0x00e0000 - Alternate True IDE (Alt Status Register)
- *
- * On True IDE mode Task File and Data Register are mapped at the same address.
- * To distinguish access between these two different bus data width is used:
- * 8Bit for Task File, 16Bit for Data I/O.
- *
- * After initialization we do 8/16 bit flipping (changes in SMC MODE register)
- * only inside IDE callback routines which are serialized by IDE layer,
- * so no additional locking needed.
- */
-
-#define TASK_FILE	0x00c00000
-#define ALT_MODE	0x00e00000
-#define REGS_SIZE	8
-
-#define enter_16bit(cs, mode) do {					\
-	mode = at91_sys_read(AT91_SMC_MODE(cs));			\
-	at91_sys_write(AT91_SMC_MODE(cs), mode | AT91_SMC_DBW_16);	\
-} while (0)
-
-#define leave_16bit(cs, mode) at91_sys_write(AT91_SMC_MODE(cs), mode);
-
-static void set_smc_timings(const u8 chipselect, const u16 cycle,
-			    const u16 setup, const u16 pulse,
-			    const u16 data_float, int use_iordy)
-{
-	unsigned long mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
-			     AT91_SMC_BAT_SELECT;
-
-	/* disable or enable waiting for IORDY signal */
-	if (use_iordy)
-		mode |= AT91_SMC_EXNWMODE_READY;
-
-	/* add data float cycles if needed */
-	if (data_float)
-		mode |= AT91_SMC_TDF_(data_float);
-
-	at91_sys_write(AT91_SMC_MODE(chipselect), mode);
-
-	/* setup timings in SMC */
-	at91_sys_write(AT91_SMC_SETUP(chipselect), AT91_SMC_NWESETUP_(setup) |
-						   AT91_SMC_NCS_WRSETUP_(0) |
-						   AT91_SMC_NRDSETUP_(setup) |
-						   AT91_SMC_NCS_RDSETUP_(0));
-	at91_sys_write(AT91_SMC_PULSE(chipselect), AT91_SMC_NWEPULSE_(pulse) |
-						   AT91_SMC_NCS_WRPULSE_(cycle) |
-						   AT91_SMC_NRDPULSE_(pulse) |
-						   AT91_SMC_NCS_RDPULSE_(cycle));
-	at91_sys_write(AT91_SMC_CYCLE(chipselect), AT91_SMC_NWECYCLE_(cycle) |
-						   AT91_SMC_NRDCYCLE_(cycle));
-}
-
-static unsigned int calc_mck_cycles(unsigned int ns, unsigned int mck_hz)
-{
-	u64 tmp = ns;
-
-	tmp *= mck_hz;
-	tmp += 1000*1000*1000 - 1; /* round up */
-	do_div(tmp, 1000*1000*1000);
-	return (unsigned int) tmp;
-}
-
-static void apply_timings(const u8 chipselect, const u8 pio,
-			  const struct ide_timing *timing, int use_iordy)
-{
-	unsigned int t0, t1, t2, t6z;
-	unsigned int cycle, setup, pulse, data_float;
-	unsigned int mck_hz;
-	struct clk *mck;
-
-	/* see table 22 of Compact Flash standard 4.1 for the meaning,
-	 * we do not stretch active (t2) time, so setup (t1) + hold time (th)
-	 * assure at least minimal recovery (t2i) time */
-	t0 = timing->cyc8b;
-	t1 = timing->setup;
-	t2 = timing->act8b;
-	t6z = (pio < 5) ? 30 : 20;
-
-	pdbg("t0=%u t1=%u t2=%u t6z=%u\n", t0, t1, t2, t6z);
-
-	mck = clk_get(NULL, "mck");
-	BUG_ON(IS_ERR(mck));
-	mck_hz = clk_get_rate(mck);
-	pdbg("mck_hz=%u\n", mck_hz);
-
-	cycle = calc_mck_cycles(t0, mck_hz);
-	setup = calc_mck_cycles(t1, mck_hz);
-	pulse = calc_mck_cycles(t2, mck_hz);
-	data_float = calc_mck_cycles(t6z, mck_hz);
-
-	pdbg("cycle=%u setup=%u pulse=%u data_float=%u\n",
-	     cycle, setup, pulse, data_float);
-
-	set_smc_timings(chipselect, cycle, setup, pulse, data_float, use_iordy);
-}
-
-static void at91_ide_input_data(ide_drive_t *drive, struct ide_cmd *cmd,
-				void *buf, unsigned int len)
-{
-	ide_hwif_t *hwif = drive->hwif;
-	struct ide_io_ports *io_ports = &hwif->io_ports;
-	u8 chipselect = hwif->select_data;
-	unsigned long mode;
-
-	pdbg("cs %u buf %p len %d\n", chipselect, buf, len);
-
-	len++;
-
-	enter_16bit(chipselect, mode);
-	readsw((void __iomem *)io_ports->data_addr, buf, len / 2);
-	leave_16bit(chipselect, mode);
-}
-
-static void at91_ide_output_data(ide_drive_t *drive, struct ide_cmd *cmd,
-				 void *buf, unsigned int len)
-{
-	ide_hwif_t *hwif = drive->hwif;
-	struct ide_io_ports *io_ports = &hwif->io_ports;
-	u8 chipselect = hwif->select_data;
-	unsigned long mode;
-
-	pdbg("cs %u buf %p len %d\n", chipselect,  buf, len);
-
-	enter_16bit(chipselect, mode);
-	writesw((void __iomem *)io_ports->data_addr, buf, len / 2);
-	leave_16bit(chipselect, mode);
-}
-
-static void at91_ide_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
-	struct ide_timing *timing;
-	u8 chipselect = hwif->select_data;
-	int use_iordy = 0;
-	const u8 pio = drive->pio_mode - XFER_PIO_0;
-
-	pdbg("chipselect %u pio %u\n", chipselect, pio);
-
-	timing = ide_timing_find_mode(XFER_PIO_0 + pio);
-	BUG_ON(!timing);
-
-	if (ide_pio_need_iordy(drive, pio))
-		use_iordy = 1;
-
-	apply_timings(chipselect, pio, timing, use_iordy);
-}
-
-static const struct ide_tp_ops at91_ide_tp_ops = {
-	.exec_command	= ide_exec_command,
-	.read_status	= ide_read_status,
-	.read_altstatus	= ide_read_altstatus,
-	.write_devctl	= ide_write_devctl,
-
-	.dev_select	= ide_dev_select,
-	.tf_load	= ide_tf_load,
-	.tf_read	= ide_tf_read,
-
-	.input_data	= at91_ide_input_data,
-	.output_data	= at91_ide_output_data,
-};
-
-static const struct ide_port_ops at91_ide_port_ops = {
-	.set_pio_mode	= at91_ide_set_pio_mode,
-};
-
-static const struct ide_port_info at91_ide_port_info __initdata = {
-	.port_ops	= &at91_ide_port_ops,
-	.tp_ops		= &at91_ide_tp_ops,
-	.host_flags 	= IDE_HFLAG_MMIO | IDE_HFLAG_NO_DMA | IDE_HFLAG_SINGLE |
-			  IDE_HFLAG_NO_IO_32BIT | IDE_HFLAG_UNMASK_IRQS,
-	.pio_mask 	= ATA_PIO6,
-	.chipset	= ide_generic,
-};
-
-/*
- * If interrupt is delivered through GPIO, IRQ are triggered on falling
- * and rising edge of signal. Whereas IDE device request interrupt on high
- * level (rising edge in our case). This mean we have fake interrupts, so
- * we need to check interrupt pin and exit instantly from ISR when line
- * is on low level.
- */
-
-irqreturn_t at91_irq_handler(int irq, void *dev_id)
-{
-	int ntries = 8;
-	int pin_val1, pin_val2;
-
-	/* additional deglitch, line can be noisy in badly designed PCB */
-	do {
-		pin_val1 = at91_get_gpio_value(irq);
-		pin_val2 = at91_get_gpio_value(irq);
-	} while (pin_val1 != pin_val2 && --ntries > 0);
-
-	if (pin_val1 == 0 || ntries <= 0)
-		return IRQ_HANDLED;
-
-	return ide_intr(irq, dev_id);
-}
-
-static int __init at91_ide_probe(struct platform_device *pdev)
-{
-	int ret;
-	struct ide_hw hw, *hws[] = { &hw };
-	struct ide_host *host;
-	struct resource *res;
-	unsigned long tf_base = 0, ctl_base = 0;
-	struct at91_cf_data *board = pdev->dev.platform_data;
-
-	if (!board)
-		return -ENODEV;
-
-	if (board->det_pin && at91_get_gpio_value(board->det_pin) != 0) {
-		perr("no device detected\n");
-		return -ENODEV;
-	}
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!res) {
-		perr("can't get memory resource\n");
-		return -ENODEV;
-	}
-
-	if (!devm_request_mem_region(&pdev->dev, res->start + TASK_FILE,
-				     REGS_SIZE, "ide") ||
-	    !devm_request_mem_region(&pdev->dev, res->start + ALT_MODE,
-				     REGS_SIZE, "alt")) {
-		perr("memory resources in use\n");
-		return -EBUSY;
-	}
-
-	pdbg("chipselect %u irq %u res %08lx\n", board->chipselect,
-	     board->irq_pin, (unsigned long) res->start);
-
-	tf_base = (unsigned long) devm_ioremap(&pdev->dev, res->start + TASK_FILE,
-					       REGS_SIZE);
-	ctl_base = (unsigned long) devm_ioremap(&pdev->dev, res->start + ALT_MODE,
-						REGS_SIZE);
-	if (!tf_base || !ctl_base) {
-		perr("can't map memory regions\n");
-		return -EBUSY;
-	}
-
-	memset(&hw, 0, sizeof(hw));
-
-	if (board->flags & AT91_IDE_SWAP_A0_A2) {
-		/* workaround for stupid hardware bug */
-		hw.io_ports.data_addr	= tf_base + 0;
-		hw.io_ports.error_addr	= tf_base + 4;
-		hw.io_ports.nsect_addr	= tf_base + 2;
-		hw.io_ports.lbal_addr	= tf_base + 6;
-		hw.io_ports.lbam_addr	= tf_base + 1;
-		hw.io_ports.lbah_addr	= tf_base + 5;
-		hw.io_ports.device_addr = tf_base + 3;
-		hw.io_ports.command_addr = tf_base + 7;
-		hw.io_ports.ctl_addr	= ctl_base + 3;
-	} else
-		ide_std_init_ports(&hw, tf_base, ctl_base + 6);
-
-	hw.irq = board->irq_pin;
-	hw.dev = &pdev->dev;
-
-	host = ide_host_alloc(&at91_ide_port_info, hws, 1);
-	if (!host) {
-		perr("failed to allocate ide host\n");
-		return -ENOMEM;
-	}
-
-	/* setup Static Memory Controller - PIO 0 as default */
-	apply_timings(board->chipselect, 0, ide_timing_find_mode(XFER_PIO_0), 0);
-
-	/* with GPIO interrupt we have to do quirks in handler */
-	if (gpio_is_valid(board->irq_pin))
-		host->irq_handler = at91_irq_handler;
-
-	host->ports[0]->select_data = board->chipselect;
-
-	ret = ide_host_register(host, &at91_ide_port_info, hws);
-	if (ret) {
-		perr("failed to register ide host\n");
-		goto err_free_host;
-	}
-	platform_set_drvdata(pdev, host);
-	return 0;
-
-err_free_host:
-	ide_host_free(host);
-	return ret;
-}
-
-static int __exit at91_ide_remove(struct platform_device *pdev)
-{
-	struct ide_host *host = platform_get_drvdata(pdev);
-
-	ide_host_remove(host);
-	return 0;
-}
-
-static struct platform_driver at91_ide_driver = {
-	.driver	= {
-		.name = DRV_NAME,
-		.owner = THIS_MODULE,
-	},
-	.remove	= __exit_p(at91_ide_remove),
-};
-
-static int __init at91_ide_init(void)
-{
-	return platform_driver_probe(&at91_ide_driver, at91_ide_probe);
-}
-
-static void __exit at91_ide_exit(void)
-{
-	platform_driver_unregister(&at91_ide_driver);
-}
-
-module_init(at91_ide_init);
-module_exit(at91_ide_exit);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Stanislaw Gruszka <[email protected]>");
-