Skip to contentSkip to conversation

Can't output 1680x1050 to DVI monitor via HDMI port

DISCUSSION Graeme Russ 2 participants 6 messages Feb 8, 2012

lore
Share & tools
lore
#0 lore raw

Hi Guys,

Well after all my troubles with the ASRock MB, I'm now running a Gigabyte Z68P-DS3 which only has a HDMI output. So I managed to get hold of a HDMI to DVI cable, but I can only get 1024x768 :(

$ xrandr -q
Screen 0: minimum 320 x 200, current 1024 x 768, maximum 8192 x 8192
VGA1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm
x 0mm
   1024x768       60.0*
   800x600        60.3     56.2
   848x480        60.0
   640x480        59.9
HDMI1 connected 1024x768+0+0 (normal left inverted right x axis y axis)
474mm x 296mm
   1680x1050      59.9 +   60.0
   1280x1024      75.0     60.0
   1440x900       59.9
   1280x960       60.0
   1152x864       75.0
   1024x768       75.1     60.0*
   832x624        74.6
   800x600        75.0     60.3     56.2
   640x480        75.0     60.0
   720x400        70.1
DP1 disconnected (normal left inverted right x axis y axis)

So it knows the HDMI output supports 1680x1050, but it's picking the VGA instead

Any idea how to tell it to pick HDMI?

Regards,

Graeme

#1 lore raw
Quoted 5 lines · Graeme Russ

Hi Guys,

Any idea how to tell it to pick HDMI?

$ xrandr --output HDMI1 --mode 1680x1050

Will set the display mode properly, but the gnome menu bar (normally on the bottom) appears in the middle of the screen and logging of reverts back

Regards,

Graeme

#2 lore raw
Quoted 4 lines
$ xrandr --output HDMI1 --mode 1680x1050

Will set the display mode properly, but the gnome menu bar (normally on the bottom) appears in the middle of the screen and logging of reverts back

This is a gnome thing, then. Try switching off VGA completly, gnome might then adopt to the higher resolution.

Greets,
Kiste

#3 lore raw

Hi Oliver,

Quoted 6 lines · Oliver Seitz
Quoted 4 lines
$ xrandr --output HDMI1 --mode 1680x1050

Will set the display mode properly, but the gnome menu bar (normally on the bottom) appears in the middle of the screen and logging of reverts back

This is a gnome thing, then. Try switching off VGA completly, gnome might

How?

Regards,

Graeme

#4 lore raw

Am 08.02.2012 10:55, schrieb Graeme Russ:

Quoted 11 lines

Hi Oliver,

Quoted 6 lines · Oliver Seitz
Quoted 4 lines
$ xrandr --output HDMI1 --mode 1680x1050

Will set the display mode properly, but the gnome menu bar (normally on the bottom) appears in the middle of the screen and logging of reverts back

This is a gnome thing, then. Try switching off VGA completly, gnome might

How?

xrandr --output VGA1 --off

Or, set the screens to something different than clone mode. Like

xrandr --output HDMI1 --below VGA1 xrandr --output HDMI1 --above VGA1 xrandr --output HDMI1 --left-of VGA1 xrandr --output HDMI1 --right-of VGA1

I may add, this is all very off-topic on this list.

Greets,
Kiste

#5 lore raw

Hi Oliver

Quoted 13 lines · Oliver Seitz

Am 08.02.2012 10:55, schrieb Graeme Russ:

Quoted 11 lines

Hi Oliver,

Quoted 8 lines · Oliver Seitz
Quoted 6 lines
$ xrandr --output HDMI1 --mode 1680x1050

Will set the display mode properly, but the gnome menu bar (normally on the
bottom) appears in the middle of the screen and logging of reverts back

Quoted 7 lines
Quoted 4 lines
Quoted 1 line

This is a gnome thing, then. Try switching off VGA completly, gnome might

How?

xrandr --output VGA1 --off

Thanks - That changes to the correct resolution when I logon, but the logon screen is still low-res. Good enough for now

Quoted 8 lines

Or, set the screens to something different than clone mode. Like

xrandr --output HDMI1 --below VGA1 xrandr --output HDMI1 --above VGA1 xrandr --output HDMI1 --left-of VGA1 xrandr --output HDMI1 --right-of VGA1

I may add, this is all very off-topic on this list.

Well not really, it's a i5 2500K on a Z68 motherboard using the on-die graphics - I was hoping that there was an i915 module parameter or other configuration setting which would tell the Intel gfx driver that the motherboard does not have a VGA connector (only a HDMI)

My bad - I should have explained it a bit better, sorry

Regards,

Graeme