mtd/gpmi : add gpmi support for mx6q

add gpmi support to mx6q.

Signed-off-by Huang Shijie <[email protected]>

---
v1 --> v2:
create this patch based on l2-mtd.git tree.

 drivers/mtd/nand/gpmi-nand/bch-regs.h  |   42 ++++++++++++++++++++++++-------
 drivers/mtd/nand/gpmi-nand/gpmi-lib.c  |   14 ++++++----
 drivers/mtd/nand/gpmi-nand/gpmi-nand.c |    3 ++
 drivers/mtd/nand/gpmi-nand/gpmi-nand.h |    2 +
 4 files changed, 45 insertions(+), 16 deletions(-)

drivers/mtd/nand/gpmi-nand/bch-regs.h +32 -10

index 4effb8c..a092451 100644
@@ -51,15 +51,26 @@
 
 #define BP_BCH_FLASH0LAYOUT0_ECC0		12
 #define BM_BCH_FLASH0LAYOUT0_ECC0	(0xf << BP_BCH_FLASH0LAYOUT0_ECC0)
-#define BF_BCH_FLASH0LAYOUT0_ECC0(v)		\
-	(((v) << BP_BCH_FLASH0LAYOUT0_ECC0) & BM_BCH_FLASH0LAYOUT0_ECC0)
+#define MX6Q_BP_BCH_FLASH0LAYOUT0_ECC0		11
+#define MX6Q_BM_BCH_FLASH0LAYOUT0_ECC0	(0x1f << MX6Q_BP_BCH_FLASH0LAYOUT0_ECC0)
+#define BF_BCH_FLASH0LAYOUT0_ECC0(v, x)				\
+	(GPMI_IS_MX6Q(x)					\
+		? (((v) << MX6Q_BP_BCH_FLASH0LAYOUT0_ECC0)	\
+			& MX6Q_BM_BCH_FLASH0LAYOUT0_ECC0)	\
+		: (((v) << BP_BCH_FLASH0LAYOUT0_ECC0)		\
+			& BM_BCH_FLASH0LAYOUT0_ECC0)		\
+	)
 
 #define BP_BCH_FLASH0LAYOUT0_DATA0_SIZE		0
 #define BM_BCH_FLASH0LAYOUT0_DATA0_SIZE		\
 			(0xfff << BP_BCH_FLASH0LAYOUT0_DATA0_SIZE)
-#define BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(v)	\
-	(((v) << BP_BCH_FLASH0LAYOUT0_DATA0_SIZE)\
-					 & BM_BCH_FLASH0LAYOUT0_DATA0_SIZE)
+#define MX6Q_BM_BCH_FLASH0LAYOUT0_DATA0_SIZE	\
+			(0x3ff << BP_BCH_FLASH0LAYOUT0_DATA0_SIZE)
+#define BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(v, x)				\
+	(GPMI_IS_MX6Q(x)						\
+		? (((v) >> 2) & MX6Q_BM_BCH_FLASH0LAYOUT0_DATA0_SIZE)	\
+		: ((v) & BM_BCH_FLASH0LAYOUT0_DATA0_SIZE)		\
+	)
 
 #define HW_BCH_FLASH0LAYOUT1			0x00000090
 

@@ -72,13 +83,24 @@
 
 #define BP_BCH_FLASH0LAYOUT1_ECCN		12
 #define BM_BCH_FLASH0LAYOUT1_ECCN	(0xf << BP_BCH_FLASH0LAYOUT1_ECCN)
-#define BF_BCH_FLASH0LAYOUT1_ECCN(v)		\
-	(((v) << BP_BCH_FLASH0LAYOUT1_ECCN) & BM_BCH_FLASH0LAYOUT1_ECCN)
+#define MX6Q_BP_BCH_FLASH0LAYOUT1_ECCN		11
+#define MX6Q_BM_BCH_FLASH0LAYOUT1_ECCN	(0x1f << MX6Q_BP_BCH_FLASH0LAYOUT1_ECCN)
+#define BF_BCH_FLASH0LAYOUT1_ECCN(v, x)				\
+	(GPMI_IS_MX6Q(x)					\
+		? (((v) << MX6Q_BP_BCH_FLASH0LAYOUT1_ECCN)	\
+			& MX6Q_BM_BCH_FLASH0LAYOUT1_ECCN)	\
+		: (((v) << BP_BCH_FLASH0LAYOUT1_ECCN)		\
+			& BM_BCH_FLASH0LAYOUT1_ECCN)		\
+	)
 
 #define BP_BCH_FLASH0LAYOUT1_DATAN_SIZE		0
 #define BM_BCH_FLASH0LAYOUT1_DATAN_SIZE		\
 			(0xfff << BP_BCH_FLASH0LAYOUT1_DATAN_SIZE)
-#define BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(v)	\
-	(((v) << BP_BCH_FLASH0LAYOUT1_DATAN_SIZE) \
-					 & BM_BCH_FLASH0LAYOUT1_DATAN_SIZE)
+#define MX6Q_BM_BCH_FLASH0LAYOUT1_DATAN_SIZE	\
+			(0x3ff << BP_BCH_FLASH0LAYOUT1_DATAN_SIZE)
+#define BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(v, x)				\
+	(GPMI_IS_MX6Q(x)						\
+		? (((v) >> 2) & MX6Q_BM_BCH_FLASH0LAYOUT1_DATAN_SIZE)	\
+		: ((v) & BM_BCH_FLASH0LAYOUT1_DATAN_SIZE)		\
+	)
 #endif

drivers/mtd/nand/gpmi-nand/gpmi-lib.c +8 -6

index 7db6555..cbcf022 100644
@@ -223,13 +223,13 @@ int bch_set_geometry(struct gpmi_nand_data *this)
 	/* Configure layout 0. */
 	writel(BF_BCH_FLASH0LAYOUT0_NBLOCKS(block_count)
 			| BF_BCH_FLASH0LAYOUT0_META_SIZE(metadata_size)
-			| BF_BCH_FLASH0LAYOUT0_ECC0(ecc_strength)
-			| BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(block_size),
+			| BF_BCH_FLASH0LAYOUT0_ECC0(ecc_strength, this)
+			| BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(block_size, this),
 			r->bch_regs + HW_BCH_FLASH0LAYOUT0);
 
 	writel(BF_BCH_FLASH0LAYOUT1_PAGE_SIZE(page_size)
-			| BF_BCH_FLASH0LAYOUT1_ECCN(ecc_strength)
-			| BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(block_size),
+			| BF_BCH_FLASH0LAYOUT1_ECCN(ecc_strength, this)
+			| BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(block_size, this),
 			r->bch_regs + HW_BCH_FLASH0LAYOUT1);
 
 	/* Set *all* chip selects to use layout 0. */

@@ -803,7 +803,8 @@ int gpmi_is_ready(struct gpmi_nand_data *this, unsigned chip)
 	if (GPMI_IS_MX23(this)) {
 		mask = MX23_BM_GPMI_DEBUG_READY0 << chip;
 		reg = readl(r->gpmi_regs + HW_GPMI_DEBUG);
-	} else if (GPMI_IS_MX28(this)) {
+	} else if (GPMI_IS_MX28(this) || GPMI_IS_MX6Q(this)) {
+		/* MX28 shares the same R/B register as MX6Q. */
 		mask = MX28_BF_GPMI_STAT_READY_BUSY(1 << chip);
 		reg = readl(r->gpmi_regs + HW_GPMI_STAT);
 	} else

@@ -1055,8 +1056,9 @@ int gpmi_read_page(struct gpmi_nand_data *this,
 		| BF_GPMI_CTRL0_ADDRESS(address)
 		| BF_GPMI_CTRL0_XFER_COUNT(geo->page_size);
 	pio[1] = 0;
+	pio[2] = 0; /* Set GPMI_HW_GPMI_ECCCTRL, disable the BCH. */
 	desc = channel->device->device_prep_slave_sg(channel,
-				(struct scatterlist *)pio, 2,
+				(struct scatterlist *)pio, 3,
 				DMA_TRANS_NONE, 1);
 	if (!desc) {
 		pr_err("step 3 error\n");

drivers/mtd/nand/gpmi-nand/gpmi-nand.c +3 -0

index f39f83e..cfcc0eb 100644
@@ -1582,6 +1582,9 @@ static const struct platform_device_id gpmi_ids[] = {
 	}, {
 		.name = "imx28-gpmi-nand",
 		.driver_data = IS_MX28,
+	}, {
+		.name = "imx6q-gpmi-nand",
+		.driver_data = IS_MX6Q,
 	}, {},
 };
 

drivers/mtd/nand/gpmi-nand/gpmi-nand.h +2 -0

index e023bcc..c93b0ae 100644
@@ -268,6 +268,8 @@ extern int gpmi_read_page(struct gpmi_nand_data *,
 /* Use the platform_id to distinguish different Archs. */
 #define IS_MX23			0x1
 #define IS_MX28			0x2
+#define IS_MX6Q			0x8
 #define GPMI_IS_MX23(x)		((x)->pdev->id_entry->driver_data == IS_MX23)
 #define GPMI_IS_MX28(x)		((x)->pdev->id_entry->driver_data == IS_MX28)
+#define GPMI_IS_MX6Q(x)		((x)->pdev->id_entry->driver_data == IS_MX6Q)
 #endif