ssb/bcma/BCM47XX: sprom fixes and extensions

index bbc2612..f169621 100644
@@ -33,8 +33,8 @@ struct ssb_sprom {
 	u8 et1mdcport;		/* MDIO for enet1 */
 	u16 board_rev;		/* Board revision number from SPROM. */
 	u8 country_code;	/* Country Code */
-	u16 leddc_on_time;	/* LED Powersave Duty Cycle On Count */
-	u16 leddc_off_time;	/* LED Powersave Duty Cycle Off Count */
+	u8 leddc_on_time;	/* LED Powersave Duty Cycle On Count */
+	u8 leddc_off_time;	/* LED Powersave Duty Cycle Off Count */
 	u8 ant_available_a;	/* 2GHz antenna available bits (up to 4) */
 	u8 ant_available_bg;	/* 5GHz antenna available bits (up to 4) */
 	u16 pa0b0;

@@ -53,10 +53,10 @@ struct ssb_sprom {
 	u8 gpio1;		/* GPIO pin 1 */
 	u8 gpio2;		/* GPIO pin 2 */
 	u8 gpio3;		/* GPIO pin 3 */
-	u16 maxpwr_bg;		/* 2.4GHz Amplifier Max Power (in dBm Q5.2) */
-	u16 maxpwr_al;		/* 5.2GHz Amplifier Max Power (in dBm Q5.2) */
-	u16 maxpwr_a;		/* 5.3GHz Amplifier Max Power (in dBm Q5.2) */
-	u16 maxpwr_ah;		/* 5.8GHz Amplifier Max Power (in dBm Q5.2) */
+	u8 maxpwr_bg;		/* 2.4GHz Amplifier Max Power (in dBm Q5.2) */
+	u8 maxpwr_al;		/* 5.2GHz Amplifier Max Power (in dBm Q5.2) */
+	u8 maxpwr_a;		/* 5.3GHz Amplifier Max Power (in dBm Q5.2) */
+	u8 maxpwr_ah;		/* 5.8GHz Amplifier Max Power (in dBm Q5.2) */
 	u8 itssi_a;		/* Idle TSSI Target for A-PHY */
 	u8 itssi_bg;		/* Idle TSSI Target for B/G-PHY */
 	u8 tri2g;		/* 2.4GHz TX isolation */

@@ -67,8 +67,8 @@ struct ssb_sprom {
 	u8 txpid5gl[4];		/* 4.9 - 5.1GHz TX power index */
 	u8 txpid5g[4];		/* 5.1 - 5.5GHz TX power index */
 	u8 txpid5gh[4];		/* 5.5 - ...GHz TX power index */
-	u8 rxpo2g;		/* 2GHz RX power offset */
-	u8 rxpo5g;		/* 5GHz RX power offset */
+	s8 rxpo2g;		/* 2GHz RX power offset */
+	s8 rxpo5g;		/* 5GHz RX power offset */
 	u8 rssisav2g;		/* 2GHz RSSI params */
 	u8 rssismc2g;
 	u8 rssismf2g;

index 96faaef..9503341 100644
@@ -1860,7 +1860,7 @@ void b43legacy_phy_xmitpower(struct b43legacy_wldev *dev)
 	 * which accounts for the factor of 4 */
 #define REG_MAX_PWR 20
 	max_pwr = min(REG_MAX_PWR * 4
-		      - dev->dev->bus->sprom.antenna_gain.ghz24.a0
+		      - dev->dev->bus->sprom.antenna_gain.a0
 		      - 0x6, max_pwr);
 
 	/* find the desired power in Q5.2 - power_level is in dBm

index befa89e..9d8e39d 100644
@@ -390,20 +390,12 @@ static void sprom_extract_r123(struct ssb_sprom *out, const u16 *in)
 		SPEX(boardflags_hi, SSB_SPROM2_BFLHI, 0xFFFF, 0);
 
 	/* Extract the antenna gain values. */
-	gain = r123_extract_antgain(out->revision, in,
-				    SSB_SPROM1_AGAIN_BG,
-				    SSB_SPROM1_AGAIN_BG_SHIFT);
-	out->antenna_gain.ghz24.a0 = gain;
-	out->antenna_gain.ghz24.a1 = gain;
-	out->antenna_gain.ghz24.a2 = gain;
-	out->antenna_gain.ghz24.a3 = gain;
-	gain = r123_extract_antgain(out->revision, in,
-				    SSB_SPROM1_AGAIN_A,
-				    SSB_SPROM1_AGAIN_A_SHIFT);
-	out->antenna_gain.ghz5.a0 = gain;
-	out->antenna_gain.ghz5.a1 = gain;
-	out->antenna_gain.ghz5.a2 = gain;
-	out->antenna_gain.ghz5.a3 = gain;
+	out->antenna_gain.a0 = r123_extract_antgain(out->revision, in,
+						    SSB_SPROM1_AGAIN_BG,
+						    SSB_SPROM1_AGAIN_BG_SHIFT);
+	out->antenna_gain.a1 = r123_extract_antgain(out->revision, in,
+						    SSB_SPROM1_AGAIN_A,
+						    SSB_SPROM1_AGAIN_A_SHIFT);
 }
 
 /* Revs 4 5 and 8 have partially shared layout */

@@ -504,16 +496,14 @@ static void sprom_extract_r45(struct ssb_sprom *out, const u16 *in)
 	}
 
 	/* Extract the antenna gain values. */
-	SPEX(antenna_gain.ghz24.a0, SSB_SPROM4_AGAIN01,
+	SPEX(antenna_gain.a0, SSB_SPROM4_AGAIN01,
 	     SSB_SPROM4_AGAIN0, SSB_SPROM4_AGAIN0_SHIFT);
-	SPEX(antenna_gain.ghz24.a1, SSB_SPROM4_AGAIN01,
+	SPEX(antenna_gain.a1, SSB_SPROM4_AGAIN01,
 	     SSB_SPROM4_AGAIN1, SSB_SPROM4_AGAIN1_SHIFT);
-	SPEX(antenna_gain.ghz24.a2, SSB_SPROM4_AGAIN23,
+	SPEX(antenna_gain.a2, SSB_SPROM4_AGAIN23,
 	     SSB_SPROM4_AGAIN2, SSB_SPROM4_AGAIN2_SHIFT);
-	SPEX(antenna_gain.ghz24.a3, SSB_SPROM4_AGAIN23,
+	SPEX(antenna_gain.a3, SSB_SPROM4_AGAIN23,
 	     SSB_SPROM4_AGAIN3, SSB_SPROM4_AGAIN3_SHIFT);
-	memcpy(&out->antenna_gain.ghz5, &out->antenna_gain.ghz24,
-	       sizeof(out->antenna_gain.ghz5));
 
 	sprom_extract_r458(out, in);
 

@@ -602,16 +592,14 @@ static void sprom_extract_r8(struct ssb_sprom *out, const u16 *in)
 	SPEX32(ofdm5ghpo, SSB_SPROM8_OFDM5GHPO, 0xFFFFFFFF, 0);
 
 	/* Extract the antenna gain values. */
-	SPEX(antenna_gain.ghz24.a0, SSB_SPROM8_AGAIN01,
+	SPEX(antenna_gain.a0, SSB_SPROM8_AGAIN01,
 	     SSB_SPROM8_AGAIN0, SSB_SPROM8_AGAIN0_SHIFT);
-	SPEX(antenna_gain.ghz24.a1, SSB_SPROM8_AGAIN01,
+	SPEX(antenna_gain.a1, SSB_SPROM8_AGAIN01,
 	     SSB_SPROM8_AGAIN1, SSB_SPROM8_AGAIN1_SHIFT);
-	SPEX(antenna_gain.ghz24.a2, SSB_SPROM8_AGAIN23,
+	SPEX(antenna_gain.a2, SSB_SPROM8_AGAIN23,
 	     SSB_SPROM8_AGAIN2, SSB_SPROM8_AGAIN2_SHIFT);
-	SPEX(antenna_gain.ghz24.a3, SSB_SPROM8_AGAIN23,
+	SPEX(antenna_gain.a3, SSB_SPROM8_AGAIN23,
 	     SSB_SPROM8_AGAIN3, SSB_SPROM8_AGAIN3_SHIFT);
-	memcpy(&out->antenna_gain.ghz5, &out->antenna_gain.ghz24,
-	       sizeof(out->antenna_gain.ghz5));
 
 	/* Extract cores power info info */
 	for (i = 0; i < ARRAY_SIZE(pwr_info_offset); i++) {

index c821c6b..fbafed5 100644
@@ -676,14 +676,10 @@ static int ssb_pcmcia_do_get_invariants(struct pcmcia_device *p_dev,
 	case SSB_PCMCIA_CIS_ANTGAIN:
 		GOTO_ERROR_ON(tuple->TupleDataLen != 2,
 			"antg tpl size");
-		sprom->antenna_gain.ghz24.a0 = tuple->TupleData[1];
-		sprom->antenna_gain.ghz24.a1 = tuple->TupleData[1];
-		sprom->antenna_gain.ghz24.a2 = tuple->TupleData[1];
-		sprom->antenna_gain.ghz24.a3 = tuple->TupleData[1];
-		sprom->antenna_gain.ghz5.a0 = tuple->TupleData[1];
-		sprom->antenna_gain.ghz5.a1 = tuple->TupleData[1];
-		sprom->antenna_gain.ghz5.a2 = tuple->TupleData[1];
-		sprom->antenna_gain.ghz5.a3 = tuple->TupleData[1];
+		sprom->antenna_gain.a0 = tuple->TupleData[1];
+		sprom->antenna_gain.a1 = tuple->TupleData[1];
+		sprom->antenna_gain.a2 = tuple->TupleData[1];
+		sprom->antenna_gain.a3 = tuple->TupleData[1];
 		break;
 	case SSB_PCMCIA_CIS_BFLAGS:
 		GOTO_ERROR_ON((tuple->TupleDataLen != 3) &&

index 63fd709..b2d36f7 100644
@@ -551,14 +551,10 @@ int ssb_sdio_get_invariants(struct ssb_bus *bus,
 			case SSB_SDIO_CIS_ANTGAIN:
 				GOTO_ERROR_ON(tuple->size != 2,
 					      "antg tpl size");
-				sprom->antenna_gain.ghz24.a0 = tuple->data[1];
-				sprom->antenna_gain.ghz24.a1 = tuple->data[1];
-				sprom->antenna_gain.ghz24.a2 = tuple->data[1];
-				sprom->antenna_gain.ghz24.a3 = tuple->data[1];
-				sprom->antenna_gain.ghz5.a0 = tuple->data[1];
-				sprom->antenna_gain.ghz5.a1 = tuple->data[1];
-				sprom->antenna_gain.ghz5.a2 = tuple->data[1];
-				sprom->antenna_gain.ghz5.a3 = tuple->data[1];
+				sprom->antenna_gain.a0 = tuple->data[1];
+				sprom->antenna_gain.a1 = tuple->data[1];
+				sprom->antenna_gain.a2 = tuple->data[1];
+				sprom->antenna_gain.a3 = tuple->data[1];
 				break;
 			case SSB_SDIO_CIS_BFLAGS:
 				GOTO_ERROR_ON((tuple->size != 3) &&

index f169621..1de5675 100644
@@ -94,12 +94,7 @@ struct ssb_sprom {
 	 * on each band. Values in dBm/4 (Q5.2). Negative gain means the
 	 * loss in the connectors is bigger than the gain. */
 	struct {
-		struct {
-			s8 a0, a1, a2, a3;
-		} ghz24;	/* 2.4GHz band */
-		struct {
-			s8 a0, a1, a2, a3;
-		} ghz5;		/* 5GHz band */
+		s8 a0, a1, a2, a3;
 	} antenna_gain;
 
 	struct {

index 1de5675..4928419 100644
@@ -19,7 +19,7 @@ struct ssb_driver;
 struct ssb_sprom_core_pwr_info {
 	u8 itssi_2g, itssi_5g;
 	u8 maxpwr_2g, maxpwr_5gl, maxpwr_5g, maxpwr_5gh;
-	u16 pa_2g[3], pa_5gl[3], pa_5g[3], pa_5gh[3];
+	u16 pa_2g[4], pa_5gl[4], pa_5g[4], pa_5gh[4];
 };
 
 struct ssb_sprom {

index 4928419..44e486e 100644
@@ -33,6 +33,7 @@ struct ssb_sprom {
 	u8 et1mdcport;		/* MDIO for enet1 */
 	u16 board_rev;		/* Board revision number from SPROM. */
 	u8 country_code;	/* Country Code */
+	char ccode[2];		/* Country Code as two chars like EU or US */
 	u8 leddc_on_time;	/* LED Powersave Duty Cycle On Count */
 	u8 leddc_off_time;	/* LED Powersave Duty Cycle Off Count */
 	u8 ant_available_a;	/* 2GHz antenna available bits (up to 4) */

index 44e486e..992c47a 100644
@@ -32,6 +32,8 @@ struct ssb_sprom {
 	u8 et0mdcport;		/* MDIO for enet0 */
 	u8 et1mdcport;		/* MDIO for enet1 */
 	u16 board_rev;		/* Board revision number from SPROM. */
+	u16 board_num;		/* Board number number from SPROM. */
+	u16 board_type;		/* Board type number from SPROM. */
 	u8 country_code;	/* Country Code */
 	char ccode[2];		/* Country Code as two chars like EU or US */
 	u8 leddc_on_time;	/* LED Powersave Duty Cycle On Count */

@@ -107,7 +109,79 @@ struct ssb_sprom {
 		} ghz5;
 	} fem;
 
-	/* TODO - add any parameters needed from rev 2, 3, 4, 5 or 8 SPROMs */
+	u16 mcs2gpo[8];
+	u16 mcs5gpo[8];
+	u16 mcs5glpo[8];
+	u16 mcs5ghpo[8];
+	u8 opo;
+
+	u8 rxgainerr2ga[3];
+	u8 rxgainerr5gla[3];
+	u8 rxgainerr5gma[3];
+	u8 rxgainerr5gha[3];
+	u8 rxgainerr5gua[3];
+
+	u8 noiselvl2ga[3];
+	u8 noiselvl5gla[3];
+	u8 noiselvl5gma[3];
+	u8 noiselvl5gha[3];
+	u8 noiselvl5gua[3];
+
+	u8 regrev;
+	u8 txchain;
+	u8 rxchain;
+	u8 antswitch;
+	u16 cddpo;
+	u16 stbcpo;
+	u16 bw40po;
+	u16 bwduppo;
+
+	u8 tempthresh;
+	u8 tempoffset;
+	u16 rawtempsense;
+	u8 measpower;
+	u8 tempsense_slope;
+	u8 tempcorrx;
+	u8 tempsense_option;
+	u8 freqoffset_corr;
+	u8 iqcal_swp_dis;
+	u8 hw_iqcal_en;
+	u8 elna2g;
+	u8 elna5g;
+	u8 phycal_tempdelta;
+	u8 temps_period;
+	u8 temps_hysteresis;
+	u8 measpower1;
+	u8 measpower2;
+	u8 pcieingress_war;
+
+	/* power per rate from sromrev 9 */
+	u16 cckbw202gpo;
+	u16 cckbw20ul2gpo;
+	u32 legofdmbw202gpo;
+	u32 legofdmbw20ul2gpo;
+	u32 legofdmbw205glpo;
+	u32 legofdmbw20ul5glpo;
+	u32 legofdmbw205gmpo;
+	u32 legofdmbw20ul5gmpo;
+	u32 legofdmbw205ghpo;
+	u32 legofdmbw20ul5ghpo;
+	u32 mcsbw202gpo;
+	u32 mcsbw20ul2gpo;
+	u32 mcsbw402gpo;
+	u32 mcsbw205glpo;
+	u32 mcsbw20ul5glpo;
+	u32 mcsbw405glpo;
+	u32 mcsbw205gmpo;
+	u32 mcsbw20ul5gmpo;
+	u32 mcsbw405gmpo;
+	u32 mcsbw205ghpo;
+	u32 mcsbw20ul5ghpo;
+	u32 mcsbw405ghpo;
+	u16 mcs32po;
+	u16 legofdm40duppo;
+	u8 sar2g;
+	u8 sar5g;
 };
 
 /* Information about the PCB the circuitry is soldered on. */

index b8379b9..7e138ec 100644
@@ -61,7 +61,7 @@ static struct bus_type bcma_bus_type = {
 	.dev_attrs	= bcma_device_attrs,
 };
 
-static struct bcma_device *bcma_find_core(struct bcma_bus *bus, u16 coreid)
+struct bcma_device *bcma_find_core(struct bcma_bus *bus, u16 coreid)
 {
 	struct bcma_device *core;
 

@@ -71,6 +71,7 @@ static struct bcma_device *bcma_find_core(struct bcma_bus *bus, u16 coreid)
 	}
 	return NULL;
 }
+EXPORT_SYMBOL_GPL(bcma_find_core);
 
 static void bcma_release_core_dev(struct device *dev)
 {

index b9f65fb..46bbd08 100644
@@ -284,6 +284,7 @@ static inline void bcma_maskset16(struct bcma_device *cc,
 	bcma_write16(cc, offset, (bcma_read16(cc, offset) & mask) | set);
 }
 
+extern struct bcma_device *bcma_find_core(struct bcma_bus *bus, u16 coreid);
 extern bool bcma_core_is_enabled(struct bcma_device *core);
 extern void bcma_core_disable(struct bcma_device *core, u32 flags);
 extern int bcma_core_enable(struct bcma_device *core, u32 flags);

index ca77525..73c204d 100644
@@ -14,6 +14,45 @@
 #include <linux/dma-mapping.h>
 #include <linux/slab.h>
 
+static int(*get_fallback_sprom)(struct bcma_bus *dev, struct ssb_sprom *out);
+
+/**
+ * bcma_arch_register_fallback_sprom - Registers a method providing a
+ * fallback SPROM if no SPROM is found.
+ *
+ * @sprom_callback: The callback function.
+ *
+ * With this function the architecture implementation may register a
+ * callback handler which fills the SPROM data structure. The fallback is
+ * used for PCI based BCMA devices, where no valid SPROM can be found
+ * in the shadow registers and to provide the SPROM for SoCs where BCMA is
+ * to controll the system bus.
+ *
+ * This function is useful for weird architectures that have a half-assed
+ * BCMA device hardwired to their PCI bus.
+ *
+ * This function is available for architecture code, only. So it is not
+ * exported.
+ */
+int bcma_arch_register_fallback_sprom(int (*sprom_callback)(struct bcma_bus *bus,
+				     struct ssb_sprom *out))
+{
+	if (get_fallback_sprom)
+		return -EEXIST;
+	get_fallback_sprom = sprom_callback;
+
+	return 0;
+}
+
+static int bcma_fill_sprom_with_fallback(struct bcma_bus *bus,
+					 struct ssb_sprom *out)
+{
+	if (!get_fallback_sprom)
+		return -ENOENT;
+
+	return get_fallback_sprom(bus, out);
+}
+
 /**************************************************
  * R/W ops.
  **************************************************/

@@ -246,23 +285,43 @@ static void bcma_sprom_extract_r8(struct bcma_bus *bus, const u16 *sprom)
 	     SSB_SROM8_FEM_ANTSWLUT_SHIFT);
 }
 
+static bool bcma_is_sprom_available(struct bcma_bus *bus)
+{
+	u32 sromctrl;
+
+	if (!(bus->drv_cc.capabilities & BCMA_CC_CAP_SPROM))
+		return false;
+
+	if (bus->drv_cc.core->id.rev >= 32) {
+		sromctrl = bcma_read32(bus->drv_cc.core, BCMA_CC_SROM_CONTROL);
+		return sromctrl & BCMA_CC_SROM_CONTROL_PRESENT;
+	}
+	return true;
+}
+
 int bcma_sprom_get(struct bcma_bus *bus)
 {
 	u16 offset;
 	u16 *sprom;
-	u32 sromctrl;
 	int err = 0;
 
 	if (!bus->drv_cc.core)
 		return -EOPNOTSUPP;
 
-	if (!(bus->drv_cc.capabilities & BCMA_CC_CAP_SPROM))
-		return -ENOENT;
-
-	if (bus->drv_cc.core->id.rev >= 32) {
-		sromctrl = bcma_read32(bus->drv_cc.core, BCMA_CC_SROM_CONTROL);
-		if (!(sromctrl & BCMA_CC_SROM_CONTROL_PRESENT))
-			return -ENOENT;
+	if (!bcma_is_sprom_available(bus)) {
+		/*
+		 * Maybe there is no SPROM on the device?
+		 * Now we ask the arch code if there is some sprom
+		 * available for this device in some other storage.
+		 */
+		err = bcma_fill_sprom_with_fallback(bus, &bus->sprom);
+		if (err) {
+			pr_warn("Using fallback SPROM failed (err %d)\n", err);
+		} else {
+			pr_debug("Using SPROM revision %d provided by"
+				 " platform.\n", bus->sprom.revision);
+			return 0;
+		}
 	}
 
 	sprom = kcalloc(SSB_SPROMSIZE_WORDS_R4, sizeof(u16),

index 46bbd08..5af9a07 100644
@@ -176,6 +176,12 @@ int __bcma_driver_register(struct bcma_driver *drv, struct module *owner);
 
 extern void bcma_driver_unregister(struct bcma_driver *drv);
 
+/* Set a fallback SPROM.
+ * See kdoc at the function definition for complete documentation. */
+extern int bcma_arch_register_fallback_sprom(
+		int (*sprom_callback)(struct bcma_bus *bus,
+		struct ssb_sprom *out));
+
 struct bcma_bus {
 	/* The MMIO area. */
 	void __iomem *mmio;

index a84e3bb..d43ceff 100644
@@ -107,8 +107,7 @@ int nvram_getenv(char *name, char *val, size_t val_len)
 		value = eq + 1;
 		if ((eq - var) == strlen(name) &&
 			strncmp(var, name, (eq - var)) == 0) {
-			snprintf(val, val_len, "%s", value);
-			return 0;
+			return snprintf(val, val_len, "%s", value);
 		}
 	}
 	return NVRAM_ERR_ENVNOTFOUND;

index 184d5ec..69ef3ef 100644
@@ -37,7 +37,7 @@ struct nvram_header {
 
 extern int nvram_getenv(char *name, char *val, size_t val_len);
 
-static inline void nvram_parse_macaddr(char *buf, u8 *macaddr)
+static inline void nvram_parse_macaddr(char *buf, u8 macaddr[6])
 {
 	if (strchr(buf, ':'))
 		sscanf(buf, "%hhx:%hhx:%hhx:%hhx:%hhx:%hhx", &macaddr[0],

157 lines not on this page · raw message

618 lines not on this page · raw message

index de95e07..5ecaf47 100644
@@ -44,4 +44,7 @@ union bcm47xx_bus {
 extern union bcm47xx_bus bcm47xx_bus;
 extern enum bcm47xx_bus_type bcm47xx_bus_type;
 
+void bcm47xx_fill_sprom(struct ssb_sprom *sprom, const char *prefix);
+void bcm47xx_fill_sprom_ethernet(struct ssb_sprom *sprom, const char *prefix);
+
 #endif /* __ASM_BCM47XX_H */

index 6b0dacd..6f8b073 100644
@@ -3,7 +3,7 @@
  *  Copyright (C) 2006 Felix Fietkau <[email protected]>
  *  Copyright (C) 2006 Michael Buesch <[email protected]>
  *  Copyright (C) 2010 Waldemar Brodkorb <[email protected]>
- *  Copyright (C) 2010-2011 Hauke Mehrtens <[email protected]>
+ *  Copyright (C) 2010-2012 Hauke Mehrtens <[email protected]>
  *
  *  This program is free software; you can redistribute  it and/or modify it
  *  under  the terms of  the GNU General  Public License as published by the

@@ -85,7 +85,7 @@ static void bcm47xx_machine_halt(void)
 }
 
 #ifdef CONFIG_BCM47XX_SSB
-static int bcm47xx_get_sprom(struct ssb_bus *bus, struct ssb_sprom *out)
+static int bcm47xx_get_sprom_ssb(struct ssb_bus *bus, struct ssb_sprom *out)
 {
 	char prefix[10];
 

@@ -102,7 +102,7 @@ static int bcm47xx_get_sprom(struct ssb_bus *bus, struct ssb_sprom *out)
 }
 
 static int bcm47xx_get_invariants(struct ssb_bus *bus,
-				   struct ssb_init_invariants *iv)
+				  struct ssb_init_invariants *iv)
 {
 	char buf[20];
 

@@ -132,7 +132,7 @@ static void __init bcm47xx_register_ssb(void)
 	char buf[100];
 	struct ssb_mipscore *mcore;
 
-	err = ssb_arch_register_fallback_sprom(&bcm47xx_get_sprom);
+	err = ssb_arch_register_fallback_sprom(&bcm47xx_get_sprom_ssb);
 	if (err)
 		printk(KERN_WARNING "bcm47xx: someone else already registered"
 			" a ssb SPROM callback handler (err %d)\n", err);

@@ -159,10 +159,41 @@ static void __init bcm47xx_register_ssb(void)
 #endif
 
 #ifdef CONFIG_BCM47XX_BCMA
+static int bcm47xx_get_sprom_bcma(struct bcma_bus *bus, struct ssb_sprom *out)
+{
+	char prefix[10];
+	struct bcma_device *core;
+
+	if (bus->hosttype == BCMA_HOSTTYPE_PCI) {
+		snprintf(prefix, sizeof(prefix), "pci/%u/%u/",
+			 bus->host_pci->bus->number + 1,
+			 PCI_SLOT(bus->host_pci->devfn));
+		bcm47xx_fill_sprom(out, prefix);
+		return 0;
+	} else if (bus->hosttype == BCMA_HOSTTYPE_SOC) {
+		bcm47xx_fill_sprom_ethernet(out, NULL);
+		core = bcma_find_core(bus, BCMA_CORE_80211);
+		if (core) {
+			snprintf(prefix, sizeof(prefix), "sb/%u/",
+				 core->core_index);
+			bcm47xx_fill_sprom(out, prefix);
+		}
+		return 0;
+	} else {
+		printk(KERN_WARNING "bcm47xx: unable to fill SPROM for given bustype.\n");
+		return -EINVAL;
+	}
+}
+
 static void __init bcm47xx_register_bcma(void)
 {
 	int err;
 
+	err = bcma_arch_register_fallback_sprom(&bcm47xx_get_sprom_bcma);
+	if (err)
+		printk(KERN_WARNING "bcm47xx: someone else already registered"
+			" a bcma SPROM callback handler (err %d)\n", err);
+
 	err = bcma_host_soc_register(&bcm47xx_bus.bcma);
 	if (err)
 		panic("Failed to initialize BCMA bus (err %d)", err);