Skip to contentSkip to conversation

ahci: sata hotplug doesn't work after suspend

DISCUSSION Jiri Slaby 3 participants 10 messages Feb 19, 2012 – Feb 28, 2012 libata

lore
Share & tools
lore

Jiri Slaby

author
#0 lore raw

Hi,

ahci hotplug stopped working here. It always worked (-next-20111206 is the last known working for sure). I'm using -next and after plugging a sata disk in, nothing happens. I don't *think* (in the traffic, it's hard to tell for sure) an interrupt is generated either. I also *think* that it works before suspend/resume, but not after. (Or maybe uptime matters?)

This happens before suspend on plug-in:
ata3: exception Emask 0x50 SAct 0x0 SErr 0x40d0800 action 0xe frozen
ata3: irq_stat 0x00000040, connection status changed
ata3: SError: { HostInt PHYRdyChg CommWake 10B8B DevExch }
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATA-8: ST31000528AS, CC38, max UDMA/133
ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata3.00: configured for UDMA/133
ata3: EH complete
scsi 2:0:0:0: Direct-Access ATA ST31000528AS CC38 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1 sdc2
sd 2:0:0:0: [sdc] Attached SCSI disk

After suspend/resume and plug-in, nothing appears in dmesg. Storing "- - -" to /sys/class/scsi_host/host*/scan doesn't help. It looks like the line is completely dead, because only ata1 and ata2 say "hard resetting link" after this (and another two disks are connected there).

I tried 'echo adapter >host_reset', but I get 'write error: Invalid argument'.

00:1f.2 SATA controller [0106]: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] [8086:2922] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port
SATA Controller [AHCI mode] [8086:2922]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0
        Interrupt: pin B routed to IRQ 43
        Region 0: I/O ports at cc00 [size=8]
        Region 1: I/O ports at c880 [size=4]
        Region 2: I/O ports at c800 [size=8]
        Region 3: I/O ports at c480 [size=4]
        Region 4: I/O ports at c400 [size=32]
        Region 5: Memory at feb7c800 (32-bit, non-prefetchable) [size=2K]
        Capabilities: [80] MSI: Enable+ Count=1/16 Maskable- 64bit-
                Address: fee0100c  Data: 4171
        Capabilities: [70] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA

PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] Vendor Specific Information: Len=06 <?> Kernel driver in use: ahci

Any ideas what that could be?

thanks,

Signature · 2 lines
js
suse labs
author
#1 lore raw
Quoted 57 lines · Jiri Slaby

Hi,

ahci hotplug stopped working here. It always worked (-next-20111206 is the last known working for sure). I'm using -next and after plugging a sata disk in, nothing happens. I don't *think* (in the traffic, it's hard to tell for sure) an interrupt is generated either. I also *think* that it works before suspend/resume, but not after. (Or maybe uptime matters?)

This happens before suspend on plug-in:
ata3: exception Emask 0x50 SAct 0x0 SErr 0x40d0800 action 0xe frozen
ata3: irq_stat 0x00000040, connection status changed
ata3: SError: { HostInt PHYRdyChg CommWake 10B8B DevExch }
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATA-8: ST31000528AS, CC38, max UDMA/133
ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata3.00: configured for UDMA/133
ata3: EH complete
scsi 2:0:0:0: Direct-Access ATA ST31000528AS CC38 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1 sdc2
sd 2:0:0:0: [sdc] Attached SCSI disk

After suspend/resume and plug-in, nothing appears in dmesg. Storing "- - -" to /sys/class/scsi_host/host*/scan doesn't help. It looks like the line is completely dead, because only ata1 and ata2 say "hard resetting link" after this (and another two disks are connected there).

I tried 'echo adapter >host_reset', but I get 'write error: Invalid argument'.

00:1f.2 SATA controller [0106]: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] [8086:2922] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port
SATA Controller [AHCI mode] [8086:2922]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0
        Interrupt: pin B routed to IRQ 43
        Region 0: I/O ports at cc00 [size=8]
        Region 1: I/O ports at c880 [size=4]
        Region 2: I/O ports at c800 [size=8]
        Region 3: I/O ports at c480 [size=4]
        Region 4: I/O ports at c400 [size=32]
        Region 5: Memory at feb7c800 (32-bit, non-prefetchable) [size=2K]
        Capabilities: [80] MSI: Enable+ Count=1/16 Maskable- 64bit-
                Address: fee0100c  Data: 4171
        Capabilities: [70] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
Quoted 7 lines

PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] Vendor Specific Information: Len=06 <?> Kernel driver in use: ahci

Any ideas what that could be?

Maybe this will help (dmesg|grep -C 2 ata3)?

parport_pc 00:07: activated
ata4: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
firewire_core: rediscovered device fw0
usb 5-1: reset low-speed USB device number 2 using uhci_hcd --
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: configured for UDMA/133
ata3: SATA link down (SStatus 0 SControl 300)
ata3: limiting SATA link speed to 1.5 Gbps
sd 1:0:0:0: [sdb] Starting disk
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: configured for UDMA/133
sd 0:0:0:0: [sda] Starting disk
ata3: SATA link down (SStatus 0 SControl 310) ata3.00: disabled
ata3.00: detaching (SCSI 2:0:0:0)
Extended CMOS year: 2000
PM: resume of devices complete after 11061.816 msecs --
ata1.00: configured for UDMA/133
sd 0:0:0:0: [sda] Starting disk
ata3: softreset failed (1st FIS failed)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
PM: resume of devices complete after 10620.205 msecs pl2303 7-1:1.0: pl2303 converter detected

Quoted 1 line

thanks,

Signature · 2 lines
js
suse labs
#2 lore raw
In reply to Jiri Slaby
Quoted 57 lines · Jiri Slaby

Hi,

ahci hotplug stopped working here. It always worked (-next-20111206 is the last known working for sure). I'm using -next and after plugging a sata disk in, nothing happens. I don't *think* (in the traffic, it's hard to tell for sure) an interrupt is generated either. I also *think* that it works before suspend/resume, but not after. (Or maybe uptime matters?)

This happens before suspend on plug-in:
ata3: exception Emask 0x50 SAct 0x0 SErr 0x40d0800 action 0xe frozen
ata3: irq_stat 0x00000040, connection status changed
ata3: SError: { HostInt PHYRdyChg CommWake 10B8B DevExch }
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATA-8: ST31000528AS, CC38, max UDMA/133
ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata3.00: configured for UDMA/133
ata3: EH complete
scsi 2:0:0:0: Direct-Access ATA ST31000528AS CC38 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1 sdc2
sd 2:0:0:0: [sdc] Attached SCSI disk

After suspend/resume and plug-in, nothing appears in dmesg. Storing "- - -" to /sys/class/scsi_host/host*/scan doesn't help. It looks like the line is completely dead, because only ata1 and ata2 say "hard resetting link" after this (and another two disks are connected there).

I tried 'echo adapter >host_reset', but I get 'write error: Invalid argument'.

00:1f.2 SATA controller [0106]: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] [8086:2922] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port
SATA Controller [AHCI mode] [8086:2922]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0
        Interrupt: pin B routed to IRQ 43
        Region 0: I/O ports at cc00 [size=8]
        Region 1: I/O ports at c880 [size=4]
        Region 2: I/O ports at c800 [size=8]
        Region 3: I/O ports at c480 [size=4]
        Region 4: I/O ports at c400 [size=32]
        Region 5: Memory at feb7c800 (32-bit, non-prefetchable) [size=2K]
        Capabilities: [80] MSI: Enable+ Count=1/16 Maskable- 64bit-
                Address: fee0100c  Data: 4171
        Capabilities: [70] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
Quoted 7 lines

PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] Vendor Specific Information: Len=06 <?> Kernel driver in use: ahci

Any ideas what that could be?

I suspect this is caused by commit 9ee4f3933930abf5cc34f8e9d69fe0e08c18f602. Maybe you could verify? I bisected this a couple of days ago but didn't have time to look into it further. Maybe Lin can help here if this is the problematic commit.

Regards,
Holger

#3 lore raw
Quoted 64 lines · Holger Macht
Quoted 63 lines · Jiri Slaby

Hi,

ahci hotplug stopped working here. It always worked (-next-20111206 is the last known working for sure). I'm using -next and after plugging a sata disk in, nothing happens. I don't *think* (in the traffic, it's hard to tell for sure) an interrupt is generated either. I also *think* that it works before suspend/resume, but not after. (Or maybe uptime matters?)

This happens before suspend on plug-in:
ata3: exception Emask 0x50 SAct 0x0 SErr 0x40d0800 action 0xe frozen
ata3: irq_stat 0x00000040, connection status changed
ata3: SError: { HostInt PHYRdyChg CommWake 10B8B DevExch }
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATA-8: ST31000528AS, CC38, max UDMA/133
ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata3.00: configured for UDMA/133
ata3: EH complete
scsi 2:0:0:0: Direct-Access ATA ST31000528AS CC38 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1 sdc2
sd 2:0:0:0: [sdc] Attached SCSI disk

After suspend/resume and plug-in, nothing appears in dmesg. Storing "- - -" to /sys/class/scsi_host/host*/scan doesn't help. It looks like the line is completely dead, because only ata1 and ata2 say "hard resetting link" after this (and another two disks are connected there).

I tried 'echo adapter >host_reset', but I get 'write error: Invalid argument'.

00:1f.2 SATA controller [0106]: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] [8086:2922] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port
SATA Controller [AHCI mode] [8086:2922]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0
        Interrupt: pin B routed to IRQ 43
        Region 0: I/O ports at cc00 [size=8]
        Region 1: I/O ports at c880 [size=4]
        Region 2: I/O ports at c800 [size=8]
        Region 3: I/O ports at c480 [size=4]
        Region 4: I/O ports at c400 [size=32]
        Region 5: Memory at feb7c800 (32-bit, non-prefetchable) [size=2K]
        Capabilities: [80] MSI: Enable+ Count=1/16 Maskable- 64bit-
                Address: fee0100c  Data: 4171
        Capabilities: [70] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA

PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] Vendor Specific Information: Len=06 <?> Kernel driver in use: ahci

Quoted 6 lines
Quoted 1 line

Any ideas what that could be?

I suspect this is caused by commit 9ee4f3933930abf5cc34f8e9d69fe0e08c18f602. Maybe you could verify? I bisected this a couple of days ago but didn't have time to look into it further. Maybe Lin can help here if this is the problematic commit.

I'll try to re-produce this issue first.

Regards,
Lin Ming

Quoted 3 lines

Regards,
Holger

author
#4 lore raw
Quoted 65 lines · Lin Ming
Quoted 64 lines · Holger Macht
Quoted 63 lines · Jiri Slaby

Hi,

ahci hotplug stopped working here. It always worked (-next-20111206 is the last known working for sure). I'm using -next and after plugging a sata disk in, nothing happens. I don't *think* (in the traffic, it's hard to tell for sure) an interrupt is generated either. I also *think* that it works before suspend/resume, but not after. (Or maybe uptime matters?)

This happens before suspend on plug-in:
ata3: exception Emask 0x50 SAct 0x0 SErr 0x40d0800 action 0xe frozen
ata3: irq_stat 0x00000040, connection status changed
ata3: SError: { HostInt PHYRdyChg CommWake 10B8B DevExch }
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATA-8: ST31000528AS, CC38, max UDMA/133
ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata3.00: configured for UDMA/133
ata3: EH complete
scsi 2:0:0:0: Direct-Access ATA ST31000528AS CC38 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1 sdc2
sd 2:0:0:0: [sdc] Attached SCSI disk

After suspend/resume and plug-in, nothing appears in dmesg. Storing "- - -" to /sys/class/scsi_host/host*/scan doesn't help. It looks like the line is completely dead, because only ata1 and ata2 say "hard resetting link" after this (and another two disks are connected there).

I tried 'echo adapter >host_reset', but I get 'write error: Invalid argument'.

00:1f.2 SATA controller [0106]: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] [8086:2922] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port
SATA Controller [AHCI mode] [8086:2922]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0
        Interrupt: pin B routed to IRQ 43
        Region 0: I/O ports at cc00 [size=8]
        Region 1: I/O ports at c880 [size=4]
        Region 2: I/O ports at c800 [size=8]
        Region 3: I/O ports at c480 [size=4]
        Region 4: I/O ports at c400 [size=32]
        Region 5: Memory at feb7c800 (32-bit, non-prefetchable) [size=2K]
        Capabilities: [80] MSI: Enable+ Count=1/16 Maskable- 64bit-
                Address: fee0100c  Data: 4171
        Capabilities: [70] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA

PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] Vendor Specific Information: Len=06 <?> Kernel driver in use: ahci

Quoted 8 lines
Quoted 6 lines
Quoted 1 line

Any ideas what that could be?

I suspect this is caused by commit 9ee4f3933930abf5cc34f8e9d69fe0e08c18f602. Maybe you could verify? I bisected this a couple of days ago but didn't have time to look into it further. Maybe Lin can help here if this is the problematic commit.

I'll try to re-produce this issue first.

Ok, just a few more information. Suspend/resume cycle is needed to see the issue. Reverting of 9ee4f3933930 helps when this is applied too (I haven't tried one or the other alone):

drivers/ata/libata-core.c +0 -0
@@ -5305,25 +5305,16 @@ static int ata_port_suspend_common(struct device

*dev, pm_message_t mesg)

static int ata_port_suspend(struct device *dev)
{
- if (pm_runtime_suspended(dev))
- return 0;
-

        return ata_port_suspend_common(dev, PMSG_SUSPEND);

}

static int ata_port_do_freeze(struct device *dev) {
- if (pm_runtime_suspended(dev))
- pm_runtime_resume(dev);
-

        return ata_port_suspend_common(dev, PMSG_FREEZE);

}

static int ata_port_poweroff(struct device *dev)
{
- if (pm_runtime_suspended(dev))
- return 0;
-

        return ata_port_suspend_common(dev, PMSG_HIBERNATE);

}

@@ -5339,16 +5330,7 @@ static int ata_port_resume_common(struct device *dev)

static int ata_port_resume(struct device *dev)
{
- int rc;
-
- rc = ata_port_resume_common(dev);
- if (!rc) {

-               pm_runtime_disable(dev);
-               pm_runtime_set_active(dev);
-               pm_runtime_enable(dev);

- }
-
- return rc;
+ return ata_port_resume_common(dev);
}

static const struct dev_pm_ops ata_port_pm_ops = {

Signature · 2 lines
js
suse labs
#5 lore raw
Quoted 73 lines · Jiri Slaby
Quoted 72 lines · Lin Ming
Quoted 70 lines · Holger Macht
Quoted 57 lines · Jiri Slaby

Hi,

ahci hotplug stopped working here. It always worked (-next-20111206 is the last known working for sure). I'm using -next and after plugging a sata disk in, nothing happens. I don't *think* (in the traffic, it's hard to tell for sure) an interrupt is generated either. I also *think* that it works before suspend/resume, but not after. (Or maybe uptime matters?)

This happens before suspend on plug-in:
ata3: exception Emask 0x50 SAct 0x0 SErr 0x40d0800 action 0xe frozen
ata3: irq_stat 0x00000040, connection status changed
ata3: SError: { HostInt PHYRdyChg CommWake 10B8B DevExch }
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATA-8: ST31000528AS, CC38, max UDMA/133
ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata3.00: configured for UDMA/133
ata3: EH complete
scsi 2:0:0:0: Direct-Access ATA ST31000528AS CC38 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1 sdc2
sd 2:0:0:0: [sdc] Attached SCSI disk

After suspend/resume and plug-in, nothing appears in dmesg. Storing "- - -" to /sys/class/scsi_host/host*/scan doesn't help. It looks like the line is completely dead, because only ata1 and ata2 say "hard resetting link" after this (and another two disks are connected there).

I tried 'echo adapter >host_reset', but I get 'write error: Invalid argument'.

00:1f.2 SATA controller [0106]: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] [8086:2922] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port
SATA Controller [AHCI mode] [8086:2922]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0
        Interrupt: pin B routed to IRQ 43
        Region 0: I/O ports at cc00 [size=8]
        Region 1: I/O ports at c880 [size=4]
        Region 2: I/O ports at c800 [size=8]
        Region 3: I/O ports at c480 [size=4]
        Region 4: I/O ports at c400 [size=32]
        Region 5: Memory at feb7c800 (32-bit, non-prefetchable) [size=2K]
        Capabilities: [80] MSI: Enable+ Count=1/16 Maskable- 64bit-
                Address: fee0100c  Data: 4171
        Capabilities: [70] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
Quoted 7 lines

PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] Vendor Specific Information: Len=06 <?> Kernel driver in use: ahci

Any ideas what that could be?

I suspect this is caused by commit 9ee4f3933930abf5cc34f8e9d69fe0e08c18f602. Maybe you could verify? I bisected this a couple of days ago but didn't have time to look into it further. Maybe Lin can help here if this is the problematic commit.

Quoted 5 lines
Quoted 1 line

I'll try to re-produce this issue first.

Ok, just a few more information. Suspend/resume cycle is needed to see the issue. Reverting of 9ee4f3933930 helps when this is applied too (I haven't tried one or the other alone):

I saw the issue after suspend/resume.
Hotplug doesn't work because the port is runtime suspended.

I'll fix it.

Thanks,
Lin Ming

Quoted 51 lines
drivers/ata/libata-core.c +1 -19
@@ -5305,25 +5305,16 @@ static int ata_port_suspend_common(struct device
 *dev, pm_message_t mesg)
 
 static int ata_port_suspend(struct device *dev)
 {
-       if (pm_runtime_suspended(dev))
-               return 0;
-
        return ata_port_suspend_common(dev, PMSG_SUSPEND);
 }
 
 static int ata_port_do_freeze(struct device *dev)
 {
-       if (pm_runtime_suspended(dev))
-               pm_runtime_resume(dev);
-
        return ata_port_suspend_common(dev, PMSG_FREEZE);
 }
 
 static int ata_port_poweroff(struct device *dev)
 {
-       if (pm_runtime_suspended(dev))
-               return 0;
-
        return ata_port_suspend_common(dev, PMSG_HIBERNATE);
 }
@@ -5339,16 +5330,7 @@ static int ata_port_resume_common(struct device *dev)
 
 static int ata_port_resume(struct device *dev)
 {
-       int rc;
-
-       rc = ata_port_resume_common(dev);
-       if (!rc) {
-               pm_runtime_disable(dev);
-               pm_runtime_set_active(dev);
-               pm_runtime_enable(dev);
-       }
-
-       return rc;
+       return ata_port_resume_common(dev);
 }
 
 static const struct dev_pm_ops ata_port_pm_ops = {
#6 lore raw
In reply to Jiri Slaby
Quoted 73 lines · Jiri Slaby
Quoted 72 lines · Lin Ming
Quoted 70 lines · Holger Macht
Quoted 57 lines · Jiri Slaby

Hi,

ahci hotplug stopped working here. It always worked (-next-20111206 is the last known working for sure). I'm using -next and after plugging a sata disk in, nothing happens. I don't *think* (in the traffic, it's hard to tell for sure) an interrupt is generated either. I also *think* that it works before suspend/resume, but not after. (Or maybe uptime matters?)

This happens before suspend on plug-in:
ata3: exception Emask 0x50 SAct 0x0 SErr 0x40d0800 action 0xe frozen
ata3: irq_stat 0x00000040, connection status changed
ata3: SError: { HostInt PHYRdyChg CommWake 10B8B DevExch }
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATA-8: ST31000528AS, CC38, max UDMA/133
ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata3.00: configured for UDMA/133
ata3: EH complete
scsi 2:0:0:0: Direct-Access ATA ST31000528AS CC38 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1 sdc2
sd 2:0:0:0: [sdc] Attached SCSI disk

After suspend/resume and plug-in, nothing appears in dmesg. Storing "- - -" to /sys/class/scsi_host/host*/scan doesn't help. It looks like the line is completely dead, because only ata1 and ata2 say "hard resetting link" after this (and another two disks are connected there).

I tried 'echo adapter >host_reset', but I get 'write error: Invalid argument'.

00:1f.2 SATA controller [0106]: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] [8086:2922] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port
SATA Controller [AHCI mode] [8086:2922]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0
        Interrupt: pin B routed to IRQ 43
        Region 0: I/O ports at cc00 [size=8]
        Region 1: I/O ports at c880 [size=4]
        Region 2: I/O ports at c800 [size=8]
        Region 3: I/O ports at c480 [size=4]
        Region 4: I/O ports at c400 [size=32]
        Region 5: Memory at feb7c800 (32-bit, non-prefetchable) [size=2K]
        Capabilities: [80] MSI: Enable+ Count=1/16 Maskable- 64bit-
                Address: fee0100c  Data: 4171
        Capabilities: [70] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
Quoted 7 lines

PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] Vendor Specific Information: Len=06 <?> Kernel driver in use: ahci

Any ideas what that could be?

I suspect this is caused by commit 9ee4f3933930abf5cc34f8e9d69fe0e08c18f602. Maybe you could verify? I bisected this a couple of days ago but didn't have time to look into it further. Maybe Lin can help here if this is the problematic commit.

Quoted 5 lines
Quoted 1 line

I'll try to re-produce this issue first.

Ok, just a few more information. Suspend/resume cycle is needed to see the issue. Reverting of 9ee4f3933930 helps when this is applied too (I haven't tried one or the other alone):

For now, the simple fix is to disable runtime pm for hotpluggable port.

Could you please try below patch?

And please also show the debug info. dmesg |grep "DEBUG: port"

Quoted 1 line

From 28bf2f0592f231c2caba816428beaffc28873d8e Mon Sep 17 00:00:00 2001

From: Lin Ming <[email protected]>
Date: Thu, 23 Feb 2012 10:21:18 +0800
Subject: [PATCH] libata: disable runtime pm for hotpluggable port

---
 drivers/ata/ahci.c             |    3 +++
 drivers/ata/ahci.h             |    3 +++
 drivers/ata/libahci.c          |   21 +++++++++++++++++++++
 drivers/ata/libata-transport.c |    6 ++++--
 include/linux/libata.h         |    4 +++-
 5 files changed, 34 insertions(+), 3 deletions(-)
drivers/ata/ahci.c +3 -0
index d07bf03..02e93ff 100644
@@ -1145,6 +1145,9 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 	if (hpriv->cap & HOST_CAP_PMP)
 		pi.flags |= ATA_FLAG_PMP;
 
+	if (hpriv->cap & HOST_CAP_SXS)
+		pi.flags |= ATA_FLAG_EXTERNAL;
+
 	ahci_set_em_messages(hpriv, &pi);
 
 	if (ahci_broken_system_poweroff(pdev)) {
drivers/ata/ahci.h +3 -0
index b175000..92f7172 100644
@@ -172,6 +172,9 @@ enum {
 	PORT_CMD_ALPE		= (1 << 26), /* Aggressive Link PM enable */
 	PORT_CMD_ATAPI		= (1 << 24), /* Device is ATAPI */
 	PORT_CMD_FBSCP		= (1 << 22), /* FBS Capable Port */
+	PORT_CMD_ESP		= (1 << 21), /* External SATA Port */
+	PORT_CMD_MPSP		= (1 << 19), /* Mechanical Presence Switch Attached to Port */
+	PORT_CMD_HPCP		= (1 << 18), /* Hot Plug Capable Port */
 	PORT_CMD_PMP		= (1 << 17), /* PMP attached */
 	PORT_CMD_LIST_ON	= (1 << 15), /* cmd list DMA engine running */
 	PORT_CMD_FIS_ON		= (1 << 14), /* FIS DMA engine running */
drivers/ata/libahci.c +21 -0
index a72bfd0..a0222e9 100644
@@ -1097,6 +1097,24 @@ static void ahci_port_init(struct device *dev, struct ata_port *ap,
 	writel(1 << port_no, mmio + HOST_IRQ_STAT);
 }
 
+static bool ahci_port_pluggable(struct ata_port *ap)
+{
+	void __iomem *port_mmio = ahci_port_base(ap);
+	u32 cmd;
+
+	cmd = readl(port_mmio + PORT_CMD);
+	printk(KERN_ERR "DEBUG: port %d, PORT_CMD=0x%x\n", ap->port_no, cmd);
+
+	if ((ap->flags & ATA_FLAG_EXTERNAL) &&
+	    (cmd & PORT_CMD_ESP))
+		return true;
+
+	if (cmd & (PORT_CMD_MPSP | PORT_CMD_HPCP))
+		return true;
+
+	return false;
+}
+
 void ahci_init_controller(struct ata_host *host)
 {
 	struct ahci_host_priv *hpriv = host->private_data;
@@ -1112,6 +1130,9 @@ void ahci_init_controller(struct ata_host *host)
 		if (ata_port_is_dummy(ap))
 			continue;
 
+		if (ahci_port_pluggable(ap))
+			ap->flags |= ATA_FLAG_PLUGGABLE;
+
 		ahci_port_init(host->dev, ap, i, mmio, port_mmio);
 	}
 
drivers/ata/libata-transport.c +4 -2
index 74aaee3..a7166b9 100644
@@ -292,8 +292,10 @@ int ata_tport_add(struct device *parent,
 	}
 
 	device_enable_async_suspend(dev);
-	pm_runtime_set_active(dev);
-	pm_runtime_enable(dev);
+	if (!(ap->flags & ATA_FLAG_PLUGGABLE)) {
+		pm_runtime_set_active(dev);
+		pm_runtime_enable(dev);
+	}
 
 	transport_add_device(dev);
 	transport_configure_device(dev);
include/linux/libata.h +3 -1
index cafc09a..e8221cf 100644
@@ -207,8 +207,10 @@ enum {
 	ATA_FLAG_SW_ACTIVITY	= (1 << 22), /* driver supports sw activity
 					      * led */
 	ATA_FLAG_NO_DIPM	= (1 << 23), /* host not happy with DIPM */
+	ATA_FLAG_EXTERNAL	= (1 << 24), /* controller supports external SATA */
+	ATA_FLAG_PLUGGABLE	= (1 << 25), /* port is hotpluggable */
 
-	/* bits 24:31 of ap->flags are reserved for LLD specific flags */
+	/* bits 26:31 of ap->flags are reserved for LLD specific flags */
 
 
 	/* struct ata_port pflags */
Signature · 1 line
1.7.9
#7 lore raw
Quoted 80 lines · Lin Ming
Quoted 73 lines · Jiri Slaby
Quoted 72 lines · Lin Ming
Quoted 70 lines · Holger Macht
Quoted 63 lines · Jiri Slaby

Hi,

ahci hotplug stopped working here. It always worked (-next-20111206 is the last known working for sure). I'm using -next and after plugging a sata disk in, nothing happens. I don't *think* (in the traffic, it's hard to tell for sure) an interrupt is generated either. I also *think* that it works before suspend/resume, but not after. (Or maybe uptime matters?)

This happens before suspend on plug-in:
ata3: exception Emask 0x50 SAct 0x0 SErr 0x40d0800 action 0xe frozen
ata3: irq_stat 0x00000040, connection status changed
ata3: SError: { HostInt PHYRdyChg CommWake 10B8B DevExch }
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-8: ST31000528AS, CC38, max UDMA/133
ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata3.00: configured for UDMA/133
ata3: EH complete
scsi 2:0:0:0: Direct-Access     ATA      ST31000528AS     CC38 PQ: 0 ANSI: 5 sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdc: sdc1 sdc2
sd 2:0:0:0: [sdc] Attached SCSI disk

After suspend/resume and plug-in, nothing appears in dmesg. Storing "- - -" to /sys/class/scsi_host/host*/scan doesn't help. It looks like the line is completely dead, because only ata1 and ata2 say "hard resetting link" after this (and another two disks are connected there).

I tried 'echo adapter >host_reset', but I get 'write error: Invalid argument'.

00:1f.2 SATA controller [0106]: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] [8086:2922] (rev 02) (prog-if 01 [AHCI 1.0])
        Subsystem: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] [8086:2922]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin B routed to IRQ 43
        Region 0: I/O ports at cc00 [size=8]
        Region 1: I/O ports at c880 [size=4]
        Region 2: I/O ports at c800 [size=8]
        Region 3: I/O ports at c480 [size=4]
        Region 4: I/O ports at c400 [size=32]
        Region 5: Memory at feb7c800 (32-bit, non-prefetchable) [size=2K]
        Capabilities: [80] MSI: Enable+ Count=1/16 Maskable- 64bit-
                Address: fee0100c  Data: 4171
        Capabilities: [70] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
                Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
        Capabilities: [b0] Vendor Specific Information: Len=06 <?> Kernel driver in use: ahci

Quoted 1 line

Any ideas what that could be?

I suspect this is caused by commit 9ee4f3933930abf5cc34f8e9d69fe0e08c18f602. Maybe you could verify? I bisected this a couple of days ago but didn't have time to look into it further. Maybe Lin can help here if this is the problematic commit.

Quoted 5 lines
Quoted 1 line

I'll try to re-produce this issue first.

Ok, just a few more information. Suspend/resume cycle is needed to see the issue. Reverting of 9ee4f3933930 helps when this is applied too (I haven't tried one or the other alone):

Quoted 6 lines

For now, the simple fix is to disable runtime pm for hotpluggable port.

Could you please try below patch?

And please also show the debug info.
dmesg |grep "DEBUG: port"

Hi Jiri,

Will you get a chance to test this patch?

Thanks,
Lin Ming

Quoted 123 lines

From 28bf2f0592f231c2caba816428beaffc28873d8e Mon Sep 17 00:00:00 2001
From: Lin Ming <[email protected]>
Date: Thu, 23 Feb 2012 10:21:18 +0800
Subject: [PATCH] libata: disable runtime pm for hotpluggable port

---
 drivers/ata/ahci.c             |    3 +++ drivers/ata/ahci.h             |    3 +++ drivers/ata/libahci.c          |   21 +++++++++++++++++++++ drivers/ata/libata-transport.c |    6 ++++-- include/linux/libata.h         |    4 +++-

 5 files changed, 34 insertions(+), 3 deletions(-)
drivers/ata/ahci.c +3 -0
index d07bf03..02e93ff 100644
@@ -1145,6 +1145,9 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
        if (hpriv->cap & HOST_CAP_PMP)
                pi.flags |= ATA_FLAG_PMP;
 
+       if (hpriv->cap & HOST_CAP_SXS)
+               pi.flags |= ATA_FLAG_EXTERNAL;
+
        ahci_set_em_messages(hpriv, &pi);
 
        if (ahci_broken_system_poweroff(pdev)) {
drivers/ata/ahci.h +0 -0
index b175000..92f7172 100644
@@ -172,6 +172,9 @@ enum {

       PORT_CMD_ALPE           = (1 << 26), /* Aggressive Link PM enable */ PORT_CMD_ATAPI          = (1 << 24), /* Device is ATAPI */ PORT_CMD_FBSCP          = (1 << 22), /* FBS Capable Port */
+       PORT_CMD_ESP            = (1 << 21), /* External SATA Port */
+       PORT_CMD_MPSP           = (1 << 19), /* Mechanical Presence Switch Attached to Port */
+       PORT_CMD_HPCP           = (1 << 18), /* Hot Plug Capable Port */ PORT_CMD_PMP            = (1 << 17), /* PMP attached */
       PORT_CMD_LIST_ON        = (1 << 15), /* cmd list DMA engine running */ PORT_CMD_FIS_ON         = (1 << 14), /* FIS DMA engine running */

drivers/ata/libahci.c +21 -0
index a72bfd0..a0222e9 100644
@@ -1097,6 +1097,24 @@ static void ahci_port_init(struct device *dev, struct ata_port *ap,
        writel(1 << port_no, mmio + HOST_IRQ_STAT);
  }
 
+static bool ahci_port_pluggable(struct ata_port *ap)
+{
+       void __iomem *port_mmio = ahci_port_base(ap);
+       u32 cmd;
+
+       cmd = readl(port_mmio + PORT_CMD);
+       printk(KERN_ERR "DEBUG: port %d, PORT_CMD=0x%x\n", ap->port_no, cmd);
+
+       if ((ap->flags & ATA_FLAG_EXTERNAL) &&
+           (cmd & PORT_CMD_ESP))
+               return true;
+
+       if (cmd & (PORT_CMD_MPSP | PORT_CMD_HPCP))
+               return true;
+
+       return false;
+}
+
  void ahci_init_controller(struct ata_host *host)
  {
        struct ahci_host_priv *hpriv = host->private_data;
@@ -1112,6 +1130,9 @@ void ahci_init_controller(struct ata_host *host)
                if (ata_port_is_dummy(ap))
                        continue;
 
+               if (ahci_port_pluggable(ap))
+                       ap->flags |= ATA_FLAG_PLUGGABLE;
+
                ahci_port_init(host->dev, ap, i, mmio, port_mmio);
        }
 
drivers/ata/libata-transport.c +4 -2
index 74aaee3..a7166b9 100644
@@ -292,8 +292,10 @@ int ata_tport_add(struct device *parent,
        }
 
        device_enable_async_suspend(dev);
-       pm_runtime_set_active(dev);
-       pm_runtime_enable(dev);
+       if (!(ap->flags & ATA_FLAG_PLUGGABLE)) {
+               pm_runtime_set_active(dev);
+               pm_runtime_enable(dev);
+       }
 
        transport_add_device(dev);
        transport_configure_device(dev);
include/linux/libata.h +0 -0
index cafc09a..e8221cf 100644
@@ -207,8 +207,10 @@ enum {

       ATA_FLAG_SW_ACTIVITY    = (1 << 22), /* driver supports sw activity
                                             * led */
       ATA_FLAG_NO_DIPM        = (1 << 23), /* host not happy with DIPM */
+       ATA_FLAG_EXTERNAL       = (1 << 24), /* controller supports external SATA */
+       ATA_FLAG_PLUGGABLE      = (1 << 25), /* port is hotpluggable */

-       /* bits 24:31 of ap->flags are reserved for LLD specific flags */
+       /* bits 26:31 of ap->flags are reserved for LLD specific flags */

       /* struct ata_port pflags */
--
1.7.9

--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html

author
#8 lore raw
Quoted 8 lines · Lin Ming
Quoted 4 lines

Could you please try below patch?

And please also show the debug info.
dmesg |grep "DEBUG: port"

Hi Jiri,

Will you get a chance to test this patch?

Yes, yesterday I booted a kernel with that patch, today I resumed from suspend. It works fine.

[    3.544423] DEBUG: port 0, PORT_CMD=0x40006
[    3.544445] DEBUG: port 1, PORT_CMD=0x40006
[    3.544467] DEBUG: port 2, PORT_CMD=0x40006
[    3.544489] DEBUG: port 3, PORT_CMD=0x40006
[    3.544511] DEBUG: port 4, PORT_CMD=0x6
[    3.544532] DEBUG: port 5, PORT_CMD=0x6
[ 1724.132173] DEBUG: port 0, PORT_CMD=0x40006
[ 1724.132184] DEBUG: port 1, PORT_CMD=0x40006
[ 1724.132194] DEBUG: port 2, PORT_CMD=0x40006
[ 1724.132204] DEBUG: port 3, PORT_CMD=0x40006
[ 1724.132214] DEBUG: port 4, PORT_CMD=0x6
[ 1724.132222] DEBUG: port 5, PORT_CMD=0x6

thanks,

Signature · 2 lines
js
suse labs
#9 lore raw
Quoted 8 lines · Jiri Slaby
Quoted 7 lines · Lin Ming
Quoted 5 lines

Could you please try below patch?

And please also show the debug info.
dmesg |grep "DEBUG: port"

Quoted 7 lines
Quoted 3 lines

Hi Jiri,

Will you get a chance to test this patch?

Yes, yesterday I booted a kernel with that patch, today I resumed from suspend. It works fine.

Jeff,

What do you think about this patch?
Need to add similar hotplugable port check for other controllers too.

Regards,
Lin Ming

Quoted 19 lines

[    3.544423] DEBUG: port 0, PORT_CMD=0x40006 [    3.544445] DEBUG: port 1, PORT_CMD=0x40006 [    3.544467] DEBUG: port 2, PORT_CMD=0x40006 [    3.544489] DEBUG: port 3, PORT_CMD=0x40006 [    3.544511] DEBUG: port 4, PORT_CMD=0x6 [    3.544532] DEBUG: port 5, PORT_CMD=0x6

[ 1724.132173] DEBUG: port 0, PORT_CMD=0x40006
[ 1724.132184] DEBUG: port 1, PORT_CMD=0x40006
[ 1724.132194] DEBUG: port 2, PORT_CMD=0x40006
[ 1724.132204] DEBUG: port 3, PORT_CMD=0x40006
[ 1724.132214] DEBUG: port 4, PORT_CMD=0x6
[ 1724.132222] DEBUG: port 5, PORT_CMD=0x6

thanks,
--
js
suse labs