Skip to contentSkip to conversation

How to mirror traffic received on WAN interface *before* NAT?

DISCUSSION Jack Bates 2 participants 2 messages Mar 4, 2012

lore
Share & tools
lore

Jack Bates

author
#0 lore raw

We run "ntop" on a computer connected to our router, for traffic analysis: http://jdbates.blogspot.com/2012/02/this-is-followup-to-this-post-on-how-to.html

We forward all traffic sent and received on our WAN interface to the "ntop" computer with the following lines in /etc/firewall.user:

Quoted 2 lines

iptables -A PREROUTING -t mangle -i eth0.1 -j TEE --gateway 192.168.1.7 iptables -A POSTROUTING -t mangle -o eth0.1 -j TEE --gateway 192.168.1.7

This works well, except that we also NAT traffic on our WAN interface. We want to monitor traffic *before* NAT

Currently the source addresses of mirrored outgoing traffic are our "private" addresses, e.g. 192.168.1.123, 192.168.1.234, etc. so these rules happily mirror *outgoing* traffic before NAT

However the destination address of mirrored *incoming* traffic is our "public" address. I guess I want to mirror incoming traffic after NAT, so I tried "POSTROUTING" for incoming traffic:

Quoted 2 lines

iptables -A POSTROUTING -t mangle -i eth0.1 -j TEE --gateway 192.168.1.7 iptables -A POSTROUTING -t mangle -o eth0.1 -j TEE --gateway 192.168.1.7

- but I get the following error:

Quoted 1 line

iptables v1.4.6: Can't use -i with POSTROUTING

Any advice, how to improve these rules to monitor traffic *before* NAT? so analysis of incoming and outgoing traffic consistently references our "private" addresses associated with the traffic?

Any general advice concerning this setup?

#1 lore raw
Quoted 31 lines · Jack Bates

We run "ntop" on a computer connected to our router, for traffic analysis:
http://jdbates.blogspot.com/2012/02/this-is-followup-to-this-post-on-how-to.html

We forward all traffic sent and received on our WAN interface to the "ntop" computer with the following lines in /etc/firewall.user:

Quoted 2 lines

iptables -A PREROUTING -t mangle -i eth0.1 -j TEE --gateway 192.168.1.7 iptables -A POSTROUTING -t mangle -o eth0.1 -j TEE --gateway 192.168.1.7

This works well, except that we also NAT traffic on our WAN interface. We want to monitor traffic *before* NAT

Currently the source addresses of mirrored outgoing traffic are our "private" addresses, e.g. 192.168.1.123, 192.168.1.234, etc. so these rules happily mirror *outgoing* traffic before NAT

However the destination address of mirrored *incoming* traffic is our "public" address. I guess I want to mirror incoming traffic after NAT, so I tried "POSTROUTING" for incoming traffic:

Quoted 2 lines

iptables -A POSTROUTING -t mangle -i eth0.1 -j TEE --gateway 192.168.1.7 iptables -A POSTROUTING -t mangle -o eth0.1 -j TEE --gateway 192.168.1.7

- but I get the following error:

Quoted 8 lines
Quoted 1 line

iptables v1.4.6: Can't use -i with POSTROUTING

Any advice, how to improve these rules to monitor traffic *before* NAT? so analysis of incoming and outgoing traffic consistently references our "private" addresses associated with the traffic?

Any general advice concerning this setup?

<snip>
I wonder if using an IFB interface would be a better way to go. You would catch the traffic in the ingress queue which I believe will catch it before NAT. These are tc rather than iptables commands. Off the top of my head, it would be something like

modprobe ifb
ifconfig ifb0 up
tc qdisc add dev eth0 ingress
tc filter add dev eth0 parent ffff: protocol ip prio 1 u32 match u8 0 0 action mirred egress redirect dev ifb0

You would then examine the traffic on ifb0. I may not have remembered the syntax exactly and you may need a flowid parameter on the filter depending on your distribution. Hope that helps - John