sparc32: GENERIC_CLOCKEVENTS support
PATCH 1/1 sparc32: GENERIC_CLOCKEVENTS support
This patch implements GENERIC_CLOCKEVENTS support on sparc32.
The kernel uses l14 timers as clockevents. l10 timer is used as clocksource if platform master_l10_counter isn't constantly zero. The clocksource is continuous, so it's possible to use high resolution timers. l10 timer is also used as clockevent on UP configurations.
This realization is for sun4m, sun4d, sun4c and microsparc-IIep platforms. It's necessary to make appropriate changes for LEON part (it should not have l10 based cs and ce in case of SMP because of LEON's master_l10_counter is zero).
Thanks to Sam Ravnborg for the review and comments.
--- arch/sparc/Kconfig | 6 +- arch/sparc/include/asm/cpudata_32.h | 1 - arch/sparc/include/asm/timer_32.h | 14 +++ arch/sparc/include/asm/timex_32.h | 1 - arch/sparc/kernel/irq.h | 8 +- arch/sparc/kernel/kernel.h | 2 - arch/sparc/kernel/pcic.c | 50 +++++---- arch/sparc/kernel/smp_32.c | 21 +--- arch/sparc/kernel/sun4c_irq.c | 8 +- arch/sparc/kernel/sun4d_irq.c | 16 ++- arch/sparc/kernel/sun4d_smp.c | 28 ++--- arch/sparc/kernel/sun4m_irq.c | 20 ++- arch/sparc/kernel/sun4m_smp.c | 38 ++---- arch/sparc/kernel/time_32.c | 219 ++++++++++++++++++++++++++++------ 14 files changed, 281 insertions(+), 151 deletions(-)
arch/sparc/Kconfig +1 -5
@@ -70,17 +70,13 @@ config BITS default 32 if SPARC32 default 64 if SPARC64 -config ARCH_USES_GETTIMEOFFSET - bool - default y if SPARC32 - config GENERIC_CMOS_UPDATE bool default y config GENERIC_CLOCKEVENTS bool - default y if SPARC64 + default y config IOMMU_HELPER bool
arch/sparc/include/asm/cpudata_32.h +0 -1
@@ -14,7 +14,6 @@ typedef struct { unsigned long udelay_val; unsigned long clock_tick; - unsigned int multiplier; unsigned int counter; #ifdef CONFIG_SMP unsigned int irq_resched_count;
arch/sparc/include/asm/timer_32.h +14 -0
@@ -8,10 +8,24 @@#ifndef _SPARC_TIMER_H#define _SPARC_TIMER_H +#include <linux/irqreturn.h> +#include <linux/clocksource.h> +#include <asm-generic/percpu.h> #include <asm/system.h> /* For SUN4M_NCPUS */ #include <asm/btfixup.h> +#define SBUS_CLOCK_RATE 2000000/* 2MHz */ + extern __volatile__ unsigned int *master_l10_counter; +extern unsigned int (*get_cycles_offset)(void ); +extern unsigned int timer_cs_period; + +extern irqreturn_t notrace timer_interrupt(int dummy, void *dev_id); + +#ifdef CONFIG_SMP +DECLARE_PER_CPU(struct clock_event_device, sparc32_clockevent); +extern void register_percpu_ce (int cpu); +#endif /* FIXME: Make do_[gs]ettimeofday btfixup calls */ BTFIXUPDEF_CALL(int, bus_do_settimeofday, struct timespec *tv)
arch/sparc/include/asm/timex_32.h +0 -1
@@ -12,5 +12,4 @@typedef unsigned long cycles_t ;#define get_cycles () (0) -extern u32 (*do_arch_gettimeoffset)(void );#endif
arch/sparc/kernel/irq.h +7 -1
@@ -40,15 +40,21 @@ struct sun4m_irq_global {extern struct sun4m_irq_percpu __iomem *sun4m_irq_percpu[SUN4M_NCPUS ];extern struct sun4m_irq_global __iomem *sun4m_irq_global; +/* The following definitions describe the individual platform features: */ +#define FEAT_L10_CS (1 << 0)/* L10 timer is used as a clocksource */ +#define FEAT_L10_CE (1 << 1)/* L10 timer is used as a clockevent */ +#define FEAT_L14_OS (1 << 2)/* L14 timer clockevent can oneshot mode */ +/* * Platform specific irq configuration * The individual platforms assign their platform * specifics in their init functions. */ struct sparc_irq_config { -void (*init_timers)(irq_handler_t ); +void (*init_timers)(void );unsigned int (*build_device_irq)(struct platform_device *op,unsigned int real_irq); +unsigned int features; };extern struct sparc_irq_config sparc_irq_config;
arch/sparc/kernel/kernel.h +0 -2
@@ -47,8 +47,6 @@ extern void init_IRQ(void);extern void sun4c_init_IRQ (void );/* sun4m_irq.c */ -extern unsigned int lvl14_resolution; -extern void sun4m_init_IRQ (void );extern void sun4m_unmask_profile_irq (void );extern void sun4m_clear_profile_irq (int cpu);
arch/sparc/kernel/pcic.c +27 -22
73 lines not on this page · raw message
arch/sparc/kernel/smp_32.c +1 -20
@@ -301,28 +301,9 @@ void smp_flush_sig_insns(struct mm_struct *mm, unsigned long insn_addr)local_flush_sig_insns (mm, insn_addr); } -extern unsigned int lvl14_resolution; - -/* /proc/profile writes can call this, don't __init it please. */ -static DEFINE_SPINLOCK (prof_setup_lock); -int setup_profiling_timer (unsigned int multiplier) { -int i; -unsigned long flags; - -/* Prevent level14 ticker IRQ flooding. */ -if ((!multiplier) || (lvl14_resolution / multiplier) <500 ) -return -EINVAL ; - -spin_lock_irqsave (&prof_setup_lock, flags); -for_each_possible_cpu (i) { -load_profile_irq (i, lvl14_resolution / multiplier); -prof_multiplier (i) = multiplier; - } -spin_unlock_irqrestore (&prof_setup_lock, flags); - -return 0 ; +return -EINVAL ; }void __init smp_prepare_cpus (unsigned int max_cpus)
arch/sparc/kernel/sun4c_irq.c +5 -3
@@ -174,7 +174,7 @@ static void sun4c_load_profile_irq(int cpu, unsigned int limit)/* Errm.. not sure how to do this.. */ } -static void __init sun4c_init_timers (irq_handler_t counter_fn) +static void __init sun4c_init_timers (void ) {const struct linux_prom_irqs *prom_irqs;struct device_node *dp;
@@ -207,12 +207,14 @@ static void __init sun4c_init_timers(irq_handler_t counter_fn)* level 14 timer limit since we are letting the prom handle * them until we have a real console driver so L1-A works. */ -sbus_writel ((((1000000 /HZ ) +1 ) <<10 ), &sun4c_timers->l10_limit); + timer_cs_period =SBUS_CLOCK_RATE /HZ ; + sparc_irq_config.features |= (FEAT_L10_CS |FEAT_L10_CE ); +sbus_writel (((timer_cs_period +1 ) <<9 ), &sun4c_timers->l10_limit); master_l10_counter = &sun4c_timers->l10_count; irq =sun4c_build_device_irq (NULL , prom_irqs[0 ].pri); - err =request_irq (irq, counter_fn,IRQF_TIMER ,"timer" ,NULL ); + err =request_irq (irq, timer_interrupt,IRQF_TIMER ,"timer" ,NULL );if (err) {prom_printf ("sun4c_init_timers: request_irq() fails with %d\n" , err);prom_halt ();
arch/sparc/kernel/sun4d_irq.c +12 -4
@@ -282,7 +282,8 @@ static void sun4d_clear_clock_irq(void)static void sun4d_load_profile_irq (int cpu,unsigned int limit) { -bw_set_prof_limit (cpu, limit); +unsigned int value = limit ? (limit +1 ) <<9 :0 ; +bw_set_prof_limit (cpu, value); }static void __init sun4d_load_profile_irqs (void )
@@ -423,7 +424,7 @@ static void __init sun4d_fixup_trap_table(void)#endif } -static void __init sun4d_init_timers (irq_handler_t counter_fn) +static void __init sun4d_init_timers (void ) {struct device_node *dp;struct resource res;
@@ -466,12 +467,19 @@ static void __init sun4d_init_timers(irq_handler_t counter_fn)prom_halt (); } -sbus_writel ((((1000000 /HZ ) +1 ) <<10 ), &sun4d_timers->l10_timer_limit); +#ifdef CONFIG_SMP + timer_cs_period =SBUS_CLOCK_RATE *2 ;/* 2 seconds */ +#else + timer_cs_period =SBUS_CLOCK_RATE /HZ ;/* 1/HZ sec */ + sparc_irq_config.features |=FEAT_L10_CE ; +#endif + sparc_irq_config.features |=FEAT_L10_CS ; +sbus_writel (((timer_cs_period +1 ) <<9 ), &sun4d_timers->l10_timer_limit); master_l10_counter = &sun4d_timers->l10_cur_count; irq =sun4d_build_timer_irq (board,SUN4D_TIMER_IRQ ); - err =request_irq (irq, counter_fn,IRQF_TIMER ,"timer" ,NULL ); + err =request_irq (irq, timer_interrupt,IRQF_TIMER ,"timer" ,NULL );if (err) {prom_printf ("sun4d_init_timers: request_irq() failed with %d\n" , err);
arch/sparc/kernel/sun4d_smp.c +8 -20
@@ -10,11 +10,13 @@#include <linux/profile.h> #include <linux/delay.h> #include <linux/cpu.h> +#include <linux/clockchips.h> #include <asm/sbi.h> #include <asm/mmu.h> #include <asm/tlbflush.h> #include <asm/cacheflush.h> +#include <asm/timer.h> #include "kernel.h" #include "irq.h"
@@ -33,7 +35,6 @@ static inline unsigned long sun4d_swap(volatile unsigned long *ptr, unsigned lon }static void smp4d_ipi_init (void ); -static void smp_setup_percpu_timer (void );static unsigned char cpu_leds[32 ];
@@ -69,7 +70,7 @@ void __cpuinit smp4d_callin(void)* to call the scheduler code. */ /* Get our local ticker going. */ -smp_setup_percpu_timer (); +register_percpu_ce (cpuid);calibrate_delay ();smp_store_cpu_info (cpuid);
@@ -122,7 +123,6 @@ void __init smp4d_boot_cpus(void)smp4d_ipi_init ();if (boot_cpu_id) current_set[0 ] =NULL ; -smp_setup_percpu_timer ();local_flush_cache_all (); }
@@ -363,6 +363,7 @@ void smp4d_percpu_timer_interrupt(struct pt_regs *regs) {struct pt_regs *old_regs;int cpu =hard_smp4d_processor_id (); +struct clock_event_device *ce;static int cpu_tick[NR_CPUS ];static char led_mask[] = {0xe ,0xd ,0xb ,0x7 ,0xb ,0xd };
@@ -378,28 +379,15 @@ void smp4d_percpu_timer_interrupt(struct pt_regs *regs)show_leds (cpu); } -profile_tick (CPU_PROFILING ); + ce = &per_cpu (sparc32_clockevent, cpu); -if (!--prof_counter (cpu)) { -int user =user_mode (regs); +irq_enter (); + ce->event_handler (ce); +irq_exit (); -irq_enter (); -update_process_times (user); -irq_exit (); - -prof_counter (cpu) =prof_multiplier (cpu); - }set_irq_regs (old_regs); } -static void __cpuinit smp_setup_percpu_timer (void ) -{ -int cpu =hard_smp4d_processor_id (); - -prof_counter (cpu) =prof_multiplier (cpu) =1 ; -load_profile_irq (cpu, lvl14_resolution); -} -void __init smp4d_blackbox_id (unsigned *addr) {int rd = *addr &0x3e000000 ;
arch/sparc/kernel/sun4m_irq.c +13 -7
@@ -318,9 +318,6 @@ struct sun4m_timer_global {static struct sun4m_timer_global __iomem *timers_global; - -unsigned int lvl14_resolution = (((1000000 /HZ ) +1 ) <<10 ); -static void sun4m_clear_clock_irq (void ) {sbus_readl (&timers_global->l10_limit);
@@ -369,10 +366,11 @@ void sun4m_clear_profile_irq(int cpu)static void sun4m_load_profile_irq (int cpu,unsigned int limit) { -sbus_writel (limit, &timers_percpu[cpu]->l14_limit); +unsigned int value = limit ? (limit +1 ) <<9 :0 ; +sbus_writel (value, &timers_percpu[cpu]->l14_limit); } -static void __init sun4m_init_timers (irq_handler_t counter_fn) +static void __init sun4m_init_timers (void ) {struct device_node *dp =of_find_node_by_name (NULL ,"counter" );int i, err, len, num_cpu_timers;
@@ -402,13 +400,21 @@ static void __init sun4m_init_timers(irq_handler_t counter_fn)/* Every per-cpu timer works in timer mode */ sbus_writel (0x00000000 , &timers_global->timer_config); -sbus_writel ((((1000000 /HZ ) +1 ) <<10 ), &timers_global->l10_limit); +#ifdef CONFIG_SMP + timer_cs_period =SBUS_CLOCK_RATE *2 ;/* 2 seconds */ + sparc_irq_config.features |=FEAT_L14_OS ; +#else + timer_cs_period =SBUS_CLOCK_RATE /HZ ;/* 1/HZ sec */ + sparc_irq_config.features |=FEAT_L10_CE ; +#endif + sparc_irq_config.features |=FEAT_L10_CS ; +sbus_writel (((timer_cs_period +1 ) <<9 ), &timers_global->l10_limit); master_l10_counter = &timers_global->l10_count; irq =sun4m_build_device_irq (NULL ,SUN4M_TIMER_IRQ ); - err =request_irq (irq, counter_fn,IRQF_TIMER ,"timer" ,NULL ); + err =request_irq (irq, timer_interrupt,IRQF_TIMER ,"timer" ,NULL );if (err) {printk (KERN_ERR "sun4m_init_timers: Register IRQ error %d.\n" , err);
arch/sparc/kernel/sun4m_smp.c +13 -25
@@ -8,9 +8,11 @@#include <linux/profile.h> #include <linux/delay.h> #include <linux/cpu.h> +#include <linux/clockchips.h> #include <asm/cacheflush.h> #include <asm/tlbflush.h> +#include <asm/timer.h> #include "irq.h" #include "kernel.h"
@@ -30,7 +32,6 @@ swap_ulong(volatile unsigned long *ptr, unsigned long val) }static void smp4m_ipi_init (void ); -static void smp_setup_percpu_timer (void );void __cpuinit smp4m_callin (void ) {
@@ -41,8 +42,7 @@ void __cpuinit smp4m_callin(void)notify_cpu_starting (cpuid); -/* Get our local ticker going. */ -smp_setup_percpu_timer (); +register_percpu_ce (cpuid);calibrate_delay ();smp_store_cpu_info (cpuid);
@@ -86,7 +86,7 @@ void __cpuinit smp4m_callin(void)void __init smp4m_boot_cpus (void ) {smp4m_ipi_init (); -smp_setup_percpu_timer (); +sun4m_unmask_profile_irq ();local_flush_cache_all (); }
@@ -259,37 +259,25 @@ void smp4m_cross_call_irq(void)void smp4m_percpu_timer_interrupt (struct pt_regs *regs) {struct pt_regs *old_regs; +struct clock_event_device *ce;int cpu =smp_processor_id (); old_regs =set_irq_regs (regs); -sun4m_clear_profile_irq (cpu); + ce = &per_cpu (sparc32_clockevent, cpu); -profile_tick (CPU_PROFILING ); +if (ce->mode &CLOCK_EVT_MODE_PERIODIC ) +sun4m_clear_profile_irq (cpu); +else +load_profile_irq (cpu,0 );/* Is this needless? */ -if (!--prof_counter (cpu)) { -int user =user_mode (regs); +irq_enter (); + ce->event_handler (ce); +irq_exit (); -irq_enter (); -update_process_times (user); -irq_exit (); - -prof_counter (cpu) =prof_multiplier (cpu); - }set_irq_regs (old_regs); } -static void __cpuinit smp_setup_percpu_timer (void ) -{ -int cpu =smp_processor_id (); - -prof_counter (cpu) =prof_multiplier (cpu) =1 ; -load_profile_irq (cpu, lvl14_resolution); - -if (cpu = boot_cpu_id) -sun4m_unmask_profile_irq (); -} -static void __init smp4m_blackbox_id (unsigned *addr) {int rd = *addr &0x3e000000 ;
arch/sparc/kernel/time_32.c +180 -39
273 lines not on this page · raw message
PATCH 1/1 sparc32: GENERIC_CLOCKEVENTS support
This patch implements GENERIC_CLOCKEVENTS support on sparc32.
The kernel uses l14 timers as clockevents. l10 timer is used as clocksource if platform master_l10_counter isn't constantly zero. The clocksource is continuous, so it's possible to use high resolution timers. l10 timer is also used as clockevent on UP configurations.
This realization is for sun4m, sun4d, sun4c, microsparc-IIep and LEON platforms. The appropriate LEON changes was made by Konrad Eisele. Thanks!
Thanks to Sam Ravnborg for the deep review, additions and comments.
--- arch/sparc/Kconfig | 7 +- arch/sparc/include/asm/cpudata_32.h | 1 - arch/sparc/include/asm/leon.h | 3 +- arch/sparc/include/asm/timer_32.h | 29 +++++ arch/sparc/include/asm/timex_32.h | 1 - arch/sparc/kernel/irq.h | 8 +- arch/sparc/kernel/kernel.h | 2 - arch/sparc/kernel/leon_kernel.c | 189 +++++++++++++++++++++++++++++- arch/sparc/kernel/leon_smp.c | 34 +----- arch/sparc/kernel/pcic.c | 48 ++++---- arch/sparc/kernel/smp_32.c | 21 +--- arch/sparc/kernel/sun4c_irq.c | 9 +- arch/sparc/kernel/sun4d_irq.c | 17 ++- arch/sparc/kernel/sun4d_smp.c | 28 ++--- arch/sparc/kernel/sun4m_irq.c | 20 ++- arch/sparc/kernel/sun4m_smp.c | 38 ++---- arch/sparc/kernel/time_32.c | 219 ++++++++++++++++++++++++++++------ 17 files changed, 488 insertions(+), 186 deletions(-)
arch/sparc/Kconfig +1 -6
@@ -72,17 +72,12 @@ config BITS default 32 if SPARC32 default 64 if SPARC64 -config ARCH_USES_GETTIMEOFFSET - bool - default y if SPARC32 - config GENERIC_CMOS_UPDATE bool default y config GENERIC_CLOCKEVENTS - bool - default y if SPARC64 + def_bool y config IOMMU_HELPER bool
arch/sparc/include/asm/cpudata_32.h +0 -1
@@ -14,7 +14,6 @@ typedef struct { unsigned long udelay_val; unsigned long clock_tick; - unsigned int multiplier; unsigned int counter; #ifdef CONFIG_SMP unsigned int irq_resched_count;
arch/sparc/include/asm/leon.h +2 -1
@@ -323,7 +323,7 @@ extern void leon_update_virq_handling(unsigned int virq, const char *name, int do_ack);extern void leon_clear_clock_irq (void );extern void leon_load_profile_irq (int cpu,unsigned int limit); -extern void leon_init_timers (irq_handler_t counter_fn); +extern void leon_init_timers (void );extern void leon_clear_clock_irq (void );extern void leon_load_profile_irq (int cpu,unsigned int limit);extern void leon_trans_init (struct device_node *dp);
@@ -351,6 +351,7 @@ extern void init_IRQ(void);extern void cpu_panic (void );extern int __leon_processor_id (void );void leon_enable_irq_cpu (unsigned int irq_nr,unsigned int cpu); +extern void leon_register_percpu_ce (int cpu);extern irqreturn_t leon_percpu_timer_interrupt (int irq,void *unused);extern unsigned int real_irq_entry[];
arch/sparc/include/asm/timer_32.h +29 -0
@@ -8,10 +8,39 @@#ifndef _SPARC_TIMER_H#define _SPARC_TIMER_H +#include <linux/irqreturn.h> +#include <linux/clocksource.h> +#include <asm-generic/percpu.h> #include <asm/system.h> /* For SUN4M_NCPUS */ #include <asm/btfixup.h> +#define SBUS_CLOCK_RATE 2000000/* 2MHz */ +#define TIMER_VALUE_SHIFT 9 +#define TIMER_VALUE_MASK 0x3fffff +#define TIMER_LIMIT_BIT (1 << 31)/* Bit 31 in Counter-Timer register */ + +/* The counter timer register has the value offset by 9 bits. +* From sun4m manual: +* When a counter reaches the value in the corresponding limit register, +* the Limit bit is set and the counter is set to 500 nS (i.e. 0x00000200). +* +* To compensate for this add one to the value. +*/ +static inline unsigned int timer_value (unsigned int value) +{ +return (value +1 ) <<TIMER_VALUE_SHIFT ; +} + extern __volatile__ unsigned int *master_l10_counter; +extern unsigned int (*get_cycles_offset)(void ); +extern unsigned int timer_cs_period; + +extern irqreturn_t notrace timer_interrupt(int dummy, void *dev_id); + +#ifdef CONFIG_SMP +DECLARE_PER_CPU(struct clock_event_device, sparc32_clockevent); +extern void register_percpu_ce (int cpu); +#endif /* FIXME: Make do_[gs]ettimeofday btfixup calls */ BTFIXUPDEF_CALL(int, bus_do_settimeofday, struct timespec *tv)
arch/sparc/include/asm/timex_32.h +0 -1
@@ -12,5 +12,4 @@typedef unsigned long cycles_t ;#define get_cycles () (0) -extern u32 (*do_arch_gettimeoffset)(void );#endif
arch/sparc/kernel/irq.h +7 -1
@@ -40,15 +40,21 @@ struct sun4m_irq_global {extern struct sun4m_irq_percpu __iomem *sun4m_irq_percpu[SUN4M_NCPUS ];extern struct sun4m_irq_global __iomem *sun4m_irq_global; +/* The following definitions describe the individual platform features: */ +#define FEAT_L10_CLOCKSOURCE (1 << 0)/* L10 timer is used as a clocksource */ +#define FEAT_L10_CLOCKEVENT (1 << 1)/* L10 timer is used as a clockevent */ +#define FEAT_L14_ONESHOT (1 << 2)/* L14 timer clockevent can oneshot */ +/* * Platform specific irq configuration * The individual platforms assign their platform * specifics in their init functions. */ struct sparc_irq_config { -void (*init_timers)(irq_handler_t ); +void (*init_timers)(void );unsigned int (*build_device_irq)(struct platform_device *op,unsigned int real_irq); +unsigned int features; };extern struct sparc_irq_config sparc_irq_config;
arch/sparc/kernel/kernel.h +0 -2
@@ -47,8 +47,6 @@ extern void init_IRQ(void);extern void sun4c_init_IRQ (void );/* sun4m_irq.c */ -extern unsigned int lvl14_resolution; -extern void sun4m_init_IRQ (void );extern void sun4m_unmask_profile_irq (void );extern void sun4m_clear_profile_irq (int cpu);
arch/sparc/kernel/leon_kernel.c +185 -4
237 lines not on this page · raw message
arch/sparc/kernel/leon_smp.c +4 -30
@@ -23,6 +23,8 @@#include <linux/pm.h> #include <linux/delay.h> #include <linux/gfp.h> +#include <linux/cpu.h> +#include <linux/clockchips.h> #include <asm/cacheflush.h> #include <asm/tlbflush.h>
@@ -42,6 +44,7 @@#include <asm/asi.h> #include <asm/leon.h> #include <asm/leon_amba.h> +#include <asm/timer.h> #include "kernel.h"
@@ -68,8 +71,6 @@ static inline unsigned long do_swap(volatile unsigned long *ptr,return val; } -static void smp_setup_percpu_timer (void ); -void __cpuinit leon_callin (void ) {int cpuid =hard_smpleon_processor_id ();
@@ -79,7 +80,7 @@ void __cpuinit leon_callin(void)leon_configure_cache_smp ();/* Get our local ticker going. */ -smp_setup_percpu_timer (); +leon_register_percpu_ce (cpuid);calibrate_delay ();smp_store_cpu_info (cpuid);
@@ -196,7 +197,6 @@ void __init leon_boot_cpus(void)leon_smp_setbroadcast (1 <<LEON3_IRQ_TICKER );leon_configure_cache_smp (); -smp_setup_percpu_timer ();local_flush_cache_all (); }
@@ -489,32 +489,6 @@ void leon_cross_call_irq(void) ccall_info.processors_out[i] =1 ; } -irqreturn_t leon_percpu_timer_interrupt (int irq,void *unused) -{ -int cpu =smp_processor_id (); - -leon_clear_profile_irq (cpu); - -profile_tick (CPU_PROFILING ); - -if (!--prof_counter (cpu)) { -int user =user_mode (get_irq_regs ()); - -update_process_times (user); - -prof_counter (cpu) =prof_multiplier (cpu); - } - -return IRQ_HANDLED ; -} - -static void __init smp_setup_percpu_timer (void ) -{ -int cpu =smp_processor_id (); - -prof_counter (cpu) =prof_multiplier (cpu) =1 ; -} -void __init leon_blackbox_id (unsigned *addr) {int rd = *addr &0x3e000000 ;
arch/sparc/kernel/pcic.c +26 -21
72 lines not on this page · raw message
arch/sparc/kernel/smp_32.c +1 -20
@@ -301,28 +301,9 @@ void smp_flush_sig_insns(struct mm_struct *mm, unsigned long insn_addr)local_flush_sig_insns (mm, insn_addr); } -extern unsigned int lvl14_resolution; - -/* /proc/profile writes can call this, don't __init it please. */ -static DEFINE_SPINLOCK (prof_setup_lock); -int setup_profiling_timer (unsigned int multiplier) { -int i; -unsigned long flags; - -/* Prevent level14 ticker IRQ flooding. */ -if ((!multiplier) || (lvl14_resolution / multiplier) <500 ) -return -EINVAL ; - -spin_lock_irqsave (&prof_setup_lock, flags); -for_each_possible_cpu (i) { -load_profile_irq (i, lvl14_resolution / multiplier); -prof_multiplier (i) = multiplier; - } -spin_unlock_irqrestore (&prof_setup_lock, flags); - -return 0 ; +return -EINVAL ; }void __init smp_prepare_cpus (unsigned int max_cpus)
arch/sparc/kernel/sun4c_irq.c +5 -3
@@ -174,7 +174,7 @@ static void sun4c_load_profile_irq(int cpu, unsigned int limit)/* Errm.. not sure how to do this.. */ } -static void __init sun4c_init_timers (irq_handler_t counter_fn) +static void __init sun4c_init_timers (void ) {const struct linux_prom_irqs *prom_irqs;struct device_node *dp;
@@ -207,12 +207,15 @@ static void __init sun4c_init_timers(irq_handler_t counter_fn)* level 14 timer limit since we are letting the prom handle * them until we have a real console driver so L1-A works. */ -sbus_writel ((((1000000 /HZ ) +1 ) <<10 ), &sun4c_timers->l10_limit); + timer_cs_period =SBUS_CLOCK_RATE /HZ ; + sparc_irq_config.features |+FEAT_L10_CLOCKSOURCE |FEAT_L10_CLOCKEVENT ; +sbus_writel (timer_value (timer_cs_period), &sun4c_timers->l10_limit); master_l10_counter = &sun4c_timers->l10_count; irq =sun4c_build_device_irq (NULL , prom_irqs[0 ].pri); - err =request_irq (irq, counter_fn,IRQF_TIMER ,"timer" ,NULL ); + err =request_irq (irq, timer_interrupt,IRQF_TIMER ,"timer" ,NULL );if (err) {prom_printf ("sun4c_init_timers: request_irq() fails with %d\n" , err);prom_halt ();
arch/sparc/kernel/sun4d_irq.c +13 -4
@@ -282,7 +282,8 @@ static void sun4d_clear_clock_irq(void)static void sun4d_load_profile_irq (int cpu,unsigned int limit) { -bw_set_prof_limit (cpu, limit); +unsigned int value = limit ?timer_value (limit) :0 ; +bw_set_prof_limit (cpu, value); }static void __init sun4d_load_profile_irqs (void )
@@ -423,7 +424,7 @@ static void __init sun4d_fixup_trap_table(void)#endif } -static void __init sun4d_init_timers (irq_handler_t counter_fn) +static void __init sun4d_init_timers (void ) {struct device_node *dp;struct resource res;
@@ -466,12 +467,20 @@ static void __init sun4d_init_timers(irq_handler_t counter_fn)prom_halt (); } -sbus_writel ((((1000000 /HZ ) +1 ) <<10 ), &sun4d_timers->l10_timer_limit); +#ifdef CONFIG_SMP + timer_cs_period =SBUS_CLOCK_RATE *2 ;/* 2 seconds */ +#else + timer_cs_period =SBUS_CLOCK_RATE /HZ ;/* 1/HZ sec */ + sparc_irq_config.features |=FEAT_L10_CLOCKEVENT ; +#endif + sparc_irq_config.features |=FEAT_L10_CLOCKSOURCE ; +sbus_writel (timer_value (timer_cs_period), + &sun4d_timers->l10_timer_limit); master_l10_counter = &sun4d_timers->l10_cur_count; irq =sun4d_build_timer_irq (board,SUN4D_TIMER_IRQ ); - err =request_irq (irq, counter_fn,IRQF_TIMER ,"timer" ,NULL ); + err =request_irq (irq, timer_interrupt,IRQF_TIMER ,"timer" ,NULL );if (err) {prom_printf ("sun4d_init_timers: request_irq() failed with %d\n" , err);
arch/sparc/kernel/sun4d_smp.c +8 -20
@@ -10,11 +10,13 @@#include <linux/profile.h> #include <linux/delay.h> #include <linux/cpu.h> +#include <linux/clockchips.h> #include <asm/sbi.h> #include <asm/mmu.h> #include <asm/tlbflush.h> #include <asm/cacheflush.h> +#include <asm/timer.h> #include "kernel.h" #include "irq.h"
@@ -33,7 +35,6 @@ static inline unsigned long sun4d_swap(volatile unsigned long *ptr, unsigned lon }static void smp4d_ipi_init (void ); -static void smp_setup_percpu_timer (void );static unsigned char cpu_leds[32 ];
@@ -69,7 +70,7 @@ void __cpuinit smp4d_callin(void)* to call the scheduler code. */ /* Get our local ticker going. */ -smp_setup_percpu_timer (); +register_percpu_ce (cpuid);calibrate_delay ();smp_store_cpu_info (cpuid);
@@ -122,7 +123,6 @@ void __init smp4d_boot_cpus(void)smp4d_ipi_init ();if (boot_cpu_id) current_set[0 ] =NULL ; -smp_setup_percpu_timer ();local_flush_cache_all (); }
@@ -363,6 +363,7 @@ void smp4d_percpu_timer_interrupt(struct pt_regs *regs) {struct pt_regs *old_regs;int cpu =hard_smp4d_processor_id (); +struct clock_event_device *ce;static int cpu_tick[NR_CPUS ];static char led_mask[] = {0xe ,0xd ,0xb ,0x7 ,0xb ,0xd };
@@ -378,28 +379,15 @@ void smp4d_percpu_timer_interrupt(struct pt_regs *regs)show_leds (cpu); } -profile_tick (CPU_PROFILING ); + ce = &per_cpu (sparc32_clockevent, cpu); -if (!--prof_counter (cpu)) { -int user =user_mode (regs); +irq_enter (); + ce->event_handler (ce); +irq_exit (); -irq_enter (); -update_process_times (user); -irq_exit (); - -prof_counter (cpu) =prof_multiplier (cpu); - }set_irq_regs (old_regs); } -static void __cpuinit smp_setup_percpu_timer (void ) -{ -int cpu =hard_smp4d_processor_id (); - -prof_counter (cpu) =prof_multiplier (cpu) =1 ; -load_profile_irq (cpu, lvl14_resolution); -} -void __init smp4d_blackbox_id (unsigned *addr) {int rd = *addr &0x3e000000 ;
arch/sparc/kernel/sun4m_irq.c +13 -7
@@ -318,9 +318,6 @@ struct sun4m_timer_global {static struct sun4m_timer_global __iomem *timers_global; - -unsigned int lvl14_resolution = (((1000000 /HZ ) +1 ) <<10 ); -static void sun4m_clear_clock_irq (void ) {sbus_readl (&timers_global->l10_limit);
@@ -369,10 +366,11 @@ void sun4m_clear_profile_irq(int cpu)static void sun4m_load_profile_irq (int cpu,unsigned int limit) { -sbus_writel (limit, &timers_percpu[cpu]->l14_limit); +unsigned int value = limit ?timer_value (limit) :0 ; +sbus_writel (value, &timers_percpu[cpu]->l14_limit); } -static void __init sun4m_init_timers (irq_handler_t counter_fn) +static void __init sun4m_init_timers (void ) {struct device_node *dp =of_find_node_by_name (NULL ,"counter" );int i, err, len, num_cpu_timers;
@@ -402,13 +400,21 @@ static void __init sun4m_init_timers(irq_handler_t counter_fn)/* Every per-cpu timer works in timer mode */ sbus_writel (0x00000000 , &timers_global->timer_config); -sbus_writel ((((1000000 /HZ ) +1 ) <<10 ), &timers_global->l10_limit); +#ifdef CONFIG_SMP + timer_cs_period =SBUS_CLOCK_RATE *2 ;/* 2 seconds */ + sparc_irq_config.features |=FEAT_L14_ONESHOT ; +#else + timer_cs_period =SBUS_CLOCK_RATE /HZ ;/* 1/HZ sec */ + sparc_irq_config.features |=FEAT_L10_CLOCKEVENT ; +#endif + sparc_irq_config.features |=FEAT_L10_CLOCKSOURCE ; +sbus_writel (timer_value (timer_cs_period), &timers_global->l10_limit); master_l10_counter = &timers_global->l10_count; irq =sun4m_build_device_irq (NULL ,SUN4M_TIMER_IRQ ); - err =request_irq (irq, counter_fn,IRQF_TIMER ,"timer" ,NULL ); + err =request_irq (irq, timer_interrupt,IRQF_TIMER ,"timer" ,NULL );if (err) {printk (KERN_ERR "sun4m_init_timers: Register IRQ error %d.\n" , err);
arch/sparc/kernel/sun4m_smp.c +13 -25
@@ -8,9 +8,11 @@#include <linux/profile.h> #include <linux/delay.h> #include <linux/cpu.h> +#include <linux/clockchips.h> #include <asm/cacheflush.h> #include <asm/tlbflush.h> +#include <asm/timer.h> #include "irq.h" #include "kernel.h"
@@ -30,7 +32,6 @@ swap_ulong(volatile unsigned long *ptr, unsigned long val) }static void smp4m_ipi_init (void ); -static void smp_setup_percpu_timer (void );void __cpuinit smp4m_callin (void ) {
@@ -41,8 +42,7 @@ void __cpuinit smp4m_callin(void)notify_cpu_starting (cpuid); -/* Get our local ticker going. */ -smp_setup_percpu_timer (); +register_percpu_ce (cpuid);calibrate_delay ();smp_store_cpu_info (cpuid);
@@ -86,7 +86,7 @@ void __cpuinit smp4m_callin(void)void __init smp4m_boot_cpus (void ) {smp4m_ipi_init (); -smp_setup_percpu_timer (); +sun4m_unmask_profile_irq ();local_flush_cache_all (); }
@@ -259,37 +259,25 @@ void smp4m_cross_call_irq(void)void smp4m_percpu_timer_interrupt (struct pt_regs *regs) {struct pt_regs *old_regs; +struct clock_event_device *ce;int cpu =smp_processor_id (); old_regs =set_irq_regs (regs); -sun4m_clear_profile_irq (cpu); + ce = &per_cpu (sparc32_clockevent, cpu); -profile_tick (CPU_PROFILING ); +if (ce->mode &CLOCK_EVT_MODE_PERIODIC ) +sun4m_clear_profile_irq (cpu); +else +load_profile_irq (cpu,0 );/* Is this needless? */ -if (!--prof_counter (cpu)) { -int user =user_mode (regs); +irq_enter (); + ce->event_handler (ce); +irq_exit (); -irq_enter (); -update_process_times (user); -irq_exit (); - -prof_counter (cpu) =prof_multiplier (cpu); - }set_irq_regs (old_regs); } -static void __cpuinit smp_setup_percpu_timer (void ) -{ -int cpu =smp_processor_id (); - -prof_counter (cpu) =prof_multiplier (cpu) =1 ; -load_profile_irq (cpu, lvl14_resolution); - -if (cpu = boot_cpu_id) -sun4m_unmask_profile_irq (); -} -static void __init smp4m_blackbox_id (unsigned *addr) {int rd = *addr &0x3e000000 ;
arch/sparc/kernel/time_32.c +180 -39
269 lines not on this page · raw message
Hi all.
I have started to look into this combined patch-set.
The leon part puzzeles me a bit...
Ir looks like the leon parts duplicate in several cases what we already have in time_32.c.
But we prefer to use the same base functions for all platforms when it is possible.
Quoted 14 lines
arch/sparc/kernel/leon_kernel.c +2
-0@@ -10,6 +10,8 @@#include <linux/of_platform.h> #include <linux/interrupt.h> #include <linux/of_device.h> +#include <linux/clocksource.h> +#include <linux/clockchips.h> #include <asm/oplib.h> #include <asm/timer.h>
arch/sparc/kernel/leon_kernel.c line 33
Quoted 5 lines
arch/sparc/kernel/leon_kernel.c +2
-0@@ -27,12 +29,18 @@struct leon3_irqctrl_regs_map *leon3_irqctrl_regs;/* interrupt controller base address */ struct leon3_gptimer_regs_map *leon3_gptimer_regs;/* timer controller base address */ +static __cacheline_aligned_in_smp DEFINE_SEQLOCK (leon_timer_cs_lock ); +static __volatile__ u64 leon_timer_cs_internal_counter = 0;
time_32.c already define these..
arch/sparc/kernel/leon_kernel.c line 43
Quoted 10 lines
arch/sparc/kernel/leon_kernel.c +4
-0int leondebug_irq_disable;int leon_debug_irqout;static int dummy_master_l10_counter;unsigned long amba_system_id;static DEFINE_SPINLOCK (leon_irq_lock); +static char leon_timer_cs_enabled =0 ; +#ifndef CONFIG_SMP +static char leon_timer_ce_enabled =0 ; +#endif
Likewise.
Quoted 6 lines
arch/sparc/kernel/leon_kernel.c +0
-0unsigned long leon3_gptimer_irq;/* interrupt controller irq number */ unsigned long leon3_gptimer_idx;/* Timer Index (0..6) within Timer Core */ int leon3_ticker_irq;/* Timer ticker IRQ */ @@ -250,7 +258,177 @@ void leon_update_virq_handling(unsigned int virq,irq_set_chip_data (virq, (void *)mask); }
arch/sparc/kernel/leon_kernel.c void leon_update_virq_handling(unsigned int virq, · line 268
Quoted 10 lines
arch/sparc/kernel/leon_kernel.c +8
-1-void __init leon_init_timers (irq_handler_t counter_fn) +static u32 leon_cycles_offset (void ) +{ +u32 rld, val, off; + rld =LEON3_BYPASS_LOAD_PA (&leon3_gptimer_regs->e[leon3_gptimer_idx].rld); + val =LEON3_BYPASS_LOAD_PA (&leon3_gptimer_regs->e[leon3_gptimer_idx].val); + off = rld - val; +return rld - val; +}
OK
Quoted 6 lines
arch/sparc/kernel/leon_kernel.c +6
-0+ +static cycle_t leon_timer_cs_read (struct clocksource *cs) +{ +unsigned int seq, offset; +u64 cycles; +
arch/sparc/kernel/leon_kernel.c void leon_update_virq_handling(unsigned int virq, · line 284
Quoted 10 lines
arch/sparc/kernel/leon_kernel.c +10
-0+do { + seq =read_seqbegin (&leon_timer_cs_lock); + cycles = leon_timer_cs_internal_counter; + offset =leon_cycles_offset (); + }while (read_seqretry (&leon_timer_cs_lock, seq)); + + cycles *= timer_cs_period; + cycles += offset; +return cycles; +}
This is an exact copy of time_32.c:timer_cs_read - except that is uses the leon specific variables.
Quoted 17 lines
arch/sparc/kernel/leon_kernel.c +17
-0+ +static struct clocksource leon_timer_cs = { + .name ="grtimer-cs" , + .rating =200 , + .read = leon_timer_cs_read, + .mask =CLOCKSOURCE_MASK (32 ), + .flags =CLOCK_SOURCE_IS_CONTINUOUS , +}; + +#ifndef CONFIG_SMP + +static void leon_timer_ce_set_mode (enum clock_event_mode mode, +struct clock_event_device *evt) +{ +switch (mode) { +case CLOCK_EVT_MODE_PERIODIC : +case CLOCK_EVT_MODE_RESUME :
arch/sparc/kernel/leon_kernel.c void leon_update_virq_handling(unsigned int virq, · line 311
Quoted 10 lines
arch/sparc/kernel/leon_kernel.c +10
-0+ leon_timer_ce_enabled =1 ; +break ; +case CLOCK_EVT_MODE_SHUTDOWN : + leon_timer_ce_enabled =0 ; +break ; +default : +break ; + } +smp_mb (); +}
Copy of time_32.c:timer_ce_set_mode
arch/sparc/kernel/leon_kernel.c void leon_update_virq_handling(unsigned int virq, · line 319
Quoted 8 lines
arch/sparc/kernel/leon_kernel.c +8
-0+ +static struct clock_event_device leon_timer_ce = { + .name ="grtimer-ce" , + .rating =100 , + .features =CLOCK_EVT_FEAT_PERIODIC , + .set_mode = leon_timer_ce_set_mode, + .shift =32 +};
OK
Quoted 27 lines
arch/sparc/kernel/leon_kernel.c +27
-0+ +#endif /* !CONFIG_SMP */ + +static void __init leon_late_time_init (void ) +{ + leon_timer_cs_enabled =1 ; + +clocksource_register_hz (&leon_timer_cs,1000000 ); + +#ifdef CONFIG_SMP +leon_register_percpu_ce (smp_processor_id ()); +#else +BUG_ON (smp_processor_id () != boot_cpu_id); + leon_timer_ce.cpumask = cpu_possible_mask; + leon_timer_ce.mult =div_sc (1000000 ,NSEC_PER_SEC , + leon_timer_ce.shift); +clockevents_register_device (&leon_timer_ce); +#endif /* CONFIG_SMP */ +} + +/* clocksource irq, non-smp clockevent */ +irqreturn_t notrace leon_timer_interrupt(int dummy, void *dev_id) +{ +if (leon_timer_cs_enabled) { +write_seqlock (&leon_timer_cs_lock); + leon_timer_cs_internal_counter++; +write_sequnlock (&leon_timer_cs_lock);
arch/sparc/kernel/leon_kernel.c void leon_update_virq_handling(unsigned int virq, · line 356
Quoted 10 lines
arch/sparc/kernel/leon_kernel.c +10
-0+ } +#ifndef CONFIG_SMP +if (leon_timer_ce_enabled) { +if (leon_timer_ce.event_handler) + leon_timer_ce.event_handler (&leon_timer_ce); + } + +#endif +return IRQ_HANDLED ; +}
Copy of time_32.c:timer_interrupt
Are there any special reason for this duplication that I have missed?
I will look a bit deeper into the patch later today or one of the following days.
Sam
Quoted 3 lines
Copy of time_32.c:timer_interrupt
Are there any special reason for this duplication that I have missed?
The names are maybe similar but the parameters to time_ce and time_cs are different, the frequency cannot be patched for the Leon case with a lot of modifications in the generic sparc code.
-- Konrad