Skip to contentSkip to conversation

w1: Disable irqs during 1-wire bus operations, extend 1-wire reset pulse

PATCH New Markus Franke 1 participant 1 message Apr 11, 2012 1 message not in the archive W1 dallas's 1-wire bus

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

Markus Franke

author
#1 lore raw

PATCH 2/2 w1: Disable irqs during 1-wire bus operations, extend 1-wire reset pulse

This patch offers the possibility to disables irqs during w1_write_bit() and w1_reset_bus() operations as timing requirements are very strict for the 1-wire bus protocol. Per default interrupts are enabled but can be disabled via the module parameter "w1_disable_irqs".

Extend 1-wire reset pulse length from 480us to 500us as 480us is the minimum requirement for the 1-wire reset/presence pulse.

It applies to the current linux kernel git tree.

Signed-off-by Markus Franke <[email protected]>
Acked-by Evgeniy Polyakov <[email protected]>
---
 drivers/w1/w1_io.c |   22 ++++++++++++++++++----
 1 files changed, 18 insertions(+), 4 deletions(-)
drivers/w1/w1_io.c +18 -4
index 3135b2c..e10acc2 100644
@@ -31,6 +31,9 @@
 static int w1_delay_parm = 1;
 module_param_named(delay_coef, w1_delay_parm, int, 0);
 
+static int w1_disable_irqs = 0;
+module_param_named(disable_irqs, w1_disable_irqs, int, 0);
+
 static u8 w1_crc8_table[] = {
 	0, 94, 188, 226, 97, 63, 221, 131, 194, 156, 126, 32, 163, 253, 31, 65,
 	157, 195, 33, 127, 252, 162, 64, 30, 95, 1, 227, 189, 62, 96, 130, 220,

@@ -79,6 +82,10 @@ static u8 w1_touch_bit(struct w1_master *dev, int bit)
  */
 static void w1_write_bit(struct w1_master *dev, int bit)
 {
+	unsigned long flags = 0;
+
+	if(w1_disable_irqs) local_irq_save(flags);
+
 	if (bit) {
 		dev->bus_master->write_bit(dev->bus_master->data, 0);
 		w1_delay(6);

@@ -90,6 +97,8 @@ static void w1_write_bit(struct w1_master *dev, int bit)
 		dev->bus_master->write_bit(dev->bus_master->data, 1);
 		w1_delay(10);
 	}
+
+	if(w1_disable_irqs) local_irq_restore(flags);
 }
 
 /**

@@ -158,7 +167,7 @@ EXPORT_SYMBOL_GPL(w1_write_8);
 static u8 w1_read_bit(struct w1_master *dev)
 {
 	int result;
-	unsigned long flags;
+	unsigned long flags = 0;
 
 	/* sample timing is critical here */
 	local_irq_save(flags);

@@ -318,6 +327,9 @@ EXPORT_SYMBOL_GPL(w1_read_block);
 int w1_reset_bus(struct w1_master *dev)
 {
 	int result;
+	unsigned long flags = 0;
+
+	if(w1_disable_irqs) local_irq_save(flags);
 
 	if (dev->bus_master->reset_bus)
 		result = dev->bus_master->reset_bus(dev->bus_master->data) & 0x1;

@@ -330,19 +342,21 @@ int w1_reset_bus(struct w1_master *dev)
 		 * cpu for such a short amount of time AND get it back in
 		 * the maximum amount of time.
 		 */
-		w1_delay(480);
+		w1_delay(500);
 		dev->bus_master->write_bit(dev->bus_master->data, 1);
 		w1_delay(70);
 
 		result = dev->bus_master->read_bit(dev->bus_master->data) & 0x1;
-		/* minmum 70 (above) + 410 = 480 us
+		/* minmum 70 (above) + 430 = 500 us
 		 * There aren't any timing requirements between a reset and
 		 * the following transactions.  Sleeping is safe here.
 		 */
-		/* w1_delay(410); min required time */
+		/* w1_delay(430); min required time */
 		msleep(1);
 	}
 
+	if(w1_disable_irqs) local_irq_restore(flags);
+
 	return result;
 }
 EXPORT_SYMBOL_GPL(w1_reset_bus);
Signature · 1 line
1.7.5.4