ARM: at91: finnaly add multi soc in the same kernel support

index 4218647..d985af7 100644
@@ -43,6 +43,14 @@
 #define UART_OFFSET AT91_USART5
 #endif
 
+void __iomem *at91_uart;
+
+static inline void arch_decomp_setup(void)
+{
+#ifdef UART_OFFSET
+	at91_uart = (void __iomem *) UART_OFFSET;	/* physical address */
+#endif
+}
 /*
  * The following code assumes the serial port has already been
  * initialized by the bootloader.  If you didn't setup a port in

@@ -53,27 +61,21 @@
 static void putc(int c)
 {
 #ifdef UART_OFFSET
-	void __iomem *sys = (void __iomem *) UART_OFFSET;	/* physical address */
-
-	while (!(__raw_readl(sys + ATMEL_US_CSR) & ATMEL_US_TXRDY))
+	while (!(__raw_readl(at91_uart + ATMEL_US_CSR) & ATMEL_US_TXRDY))
 		barrier();
-	__raw_writel(c, sys + ATMEL_US_THR);
+	__raw_writel(c, at91_uart + ATMEL_US_THR);
 #endif
 }
 
 static inline void flush(void)
 {
 #ifdef UART_OFFSET
-	void __iomem *sys = (void __iomem *) UART_OFFSET;	/* physical address */
-
 	/* wait for transmission to complete */
-	while (!(__raw_readl(sys + ATMEL_US_CSR) & ATMEL_US_TXEMPTY))
+	while (!(__raw_readl(at91_uart + ATMEL_US_CSR) & ATMEL_US_TXEMPTY))
 		barrier();
 #endif
 }
 
-#define arch_decomp_setup()
-
 #define arch_decomp_wdog()
 
 #endif

index 603e6aa..e67317c 100644
@@ -88,11 +88,6 @@
 #define AT91RM9200_BASE_RTC	0xfffffe00	/* Real-Time Clock */
 #define AT91RM9200_BASE_MC	0xffffff00	/* Memory Controllers */
 
-#define AT91_USART0	AT91RM9200_BASE_US0
-#define AT91_USART1	AT91RM9200_BASE_US1
-#define AT91_USART2	AT91RM9200_BASE_US2
-#define AT91_USART3	AT91RM9200_BASE_US3
-
 /*
  * Internal Memory.
  */

index 08ae9af..416c7b6 100644
@@ -95,13 +95,6 @@
 #define AT91SAM9260_BASE_WDT	0xfffffd40
 #define AT91SAM9260_BASE_GPBR	0xfffffd50
 
-#define AT91_USART0	AT91SAM9260_BASE_US0
-#define AT91_USART1	AT91SAM9260_BASE_US1
-#define AT91_USART2	AT91SAM9260_BASE_US2
-#define AT91_USART3	AT91SAM9260_BASE_US3
-#define AT91_USART4	AT91SAM9260_BASE_US4
-#define AT91_USART5	AT91SAM9260_BASE_US5
-
 
 /*
  * Internal Memory.

index 44fbdc1..a041406 100644
@@ -79,10 +79,6 @@
 #define AT91SAM9261_BASE_WDT	0xfffffd40
 #define AT91SAM9261_BASE_GPBR	0xfffffd50
 
-#define AT91_USART0	AT91SAM9261_BASE_US0
-#define AT91_USART1	AT91SAM9261_BASE_US1
-#define AT91_USART2	AT91SAM9261_BASE_US2
-
 
 /*
  * Internal Memory.

index d96cbb2..d201029 100644
@@ -95,10 +95,6 @@
 #define AT91SAM9263_BASE_RTT1	0xfffffd50
 #define AT91SAM9263_BASE_GPBR	0xfffffd60
 
-#define AT91_USART0	AT91SAM9263_BASE_US0
-#define AT91_USART1	AT91SAM9263_BASE_US1
-#define AT91_USART2	AT91SAM9263_BASE_US2
-
 #define AT91_SMC	AT91_SMC0
 
 /*

index d052abc..3a4da24 100644
@@ -106,11 +106,6 @@
 #define AT91SAM9G45_BASE_RTC	0xfffffdb0
 #define AT91SAM9G45_BASE_GPBR	0xfffffd60
 
-#define AT91_USART0	AT91SAM9G45_BASE_US0
-#define AT91_USART1	AT91SAM9G45_BASE_US1
-#define AT91_USART2	AT91SAM9G45_BASE_US2
-#define AT91_USART3	AT91SAM9G45_BASE_US3
-
 /*
  * Internal Memory.
  */

index e0073eb..a15db56 100644
@@ -89,11 +89,6 @@
 #define AT91SAM9RL_BASE_GPBR	0xfffffd60
 #define AT91SAM9RL_BASE_RTC	0xfffffe00
 
-#define AT91_USART0	AT91SAM9RL_BASE_US0
-#define AT91_USART1	AT91SAM9RL_BASE_US1
-#define AT91_USART2	AT91SAM9RL_BASE_US2
-#define AT91_USART3	AT91SAM9RL_BASE_US3
-
 
 /*
  * Internal Memory.

index 88e43d5..c75ee19 100644
@@ -55,14 +55,6 @@
 #define AT91SAM9X5_BASE_USART2	0xf8024000
 
 /*
- * Base addresses for early serial code (uncompress.h)
- */
-#define AT91_DBGU	AT91_BASE_DBGU0
-#define AT91_USART0	AT91SAM9X5_BASE_USART0
-#define AT91_USART1	AT91SAM9X5_BASE_USART1
-#define AT91_USART2	AT91SAM9X5_BASE_USART2
-
-/*
  * Internal Memory.
  */
 #define AT91SAM9X5_SRAM_BASE	0x00300000	/* Internal SRAM base address */

index e9e29a6..3a01f8f 100644
@@ -22,27 +22,17 @@
 /* 9263, 9g45 */
 #define AT91_BASE_DBGU1	0xffffee00
 
-#if defined(CONFIG_ARCH_AT91RM9200)
+#if defined(CONFIG_ARCH_AT91X40)
+#include <mach/at91x40.h>
+#else
 #include <mach/at91rm9200.h>
-#elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20)
 #include <mach/at91sam9260.h>
-#elif defined(CONFIG_ARCH_AT91SAM9261) || defined(CONFIG_ARCH_AT91SAM9G10)
 #include <mach/at91sam9261.h>
-#elif defined(CONFIG_ARCH_AT91SAM9263)
 #include <mach/at91sam9263.h>
-#elif defined(CONFIG_ARCH_AT91SAM9RL)
 #include <mach/at91sam9rl.h>
-#elif defined(CONFIG_ARCH_AT91SAM9G45)
 #include <mach/at91sam9g45.h>
-#elif defined(CONFIG_ARCH_AT91SAM9X5)
 #include <mach/at91sam9x5.h>
-#elif defined(CONFIG_ARCH_AT91X40)
-#include <mach/at91x40.h>
-#else
-#error "Unsupported AT91 processor"
-#endif
 
-#if !defined(CONFIG_ARCH_AT91X40)
 /*
  * On all at91 except rm9200 and x40 have the System Controller starts
  * at address 0xffffc000 and has a size of 16KiB.

204 lines not on this page · raw message

index 364c193..d50da1a 100644
@@ -258,18 +258,6 @@ static void __init at91rm9200_register_clocks(void)
 	clk_register(&pck3);
 }
 
-static struct clk_lookup console_clock_lookup;
-
-void __init at91rm9200_set_console_clock(int id)
-{
-	if (id >= ARRAY_SIZE(usart_clocks_lookups))
-		return;
-
-	console_clock_lookup.con_id = "usart";
-	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
-	clkdev_add(&console_clock_lookup);
-}
-
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */

index 99ce5c9..d9f0d77 100644
@@ -1152,14 +1152,6 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 		at91_uarts[portnr] = pdev;
 }
 
-void __init at91_set_serial_console(unsigned portnr)
-{
-	if (portnr < ATMEL_MAX_UART) {
-		atmel_default_console_device = at91_uarts[portnr];
-		at91rm9200_set_console_clock(at91_uarts[portnr]->id);
-	}
-}
-
 void __init at91_add_device_serial(void)
 {
 	int i;

@@ -1168,14 +1160,10 @@ void __init at91_add_device_serial(void)
 		if (at91_uarts[i])
 			platform_device_register(at91_uarts[i]);
 	}
-
-	if (!atmel_default_console_device)
-		printk(KERN_INFO "AT91: No default serial console defined.\n");
 }
 #else
 void __init __deprecated at91_init_serial(struct at91_uart_config *config) {}
 void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
 void __init at91_add_device_serial(void) {}
 #endif
 

index 46f7742..a27bbec 100644
@@ -268,18 +268,6 @@ static void __init at91sam9260_register_clocks(void)
 	clk_register(&pck1);
 }
 
-static struct clk_lookup console_clock_lookup;
-
-void __init at91sam9260_set_console_clock(int id)
-{
-	if (id >= ARRAY_SIZE(usart_clocks_lookups))
-		return;
-
-	console_clock_lookup.con_id = "usart";
-	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
-	clkdev_add(&console_clock_lookup);
-}
-
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */

index 5652dde..ad00fe9 100644
@@ -1229,14 +1229,6 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 		at91_uarts[portnr] = pdev;
 }
 
-void __init at91_set_serial_console(unsigned portnr)
-{
-	if (portnr < ATMEL_MAX_UART) {
-		atmel_default_console_device = at91_uarts[portnr];
-		at91sam9260_set_console_clock(at91_uarts[portnr]->id);
-	}
-}
-
 void __init at91_add_device_serial(void)
 {
 	int i;

@@ -1245,13 +1237,9 @@ void __init at91_add_device_serial(void)
 		if (at91_uarts[i])
 			platform_device_register(at91_uarts[i]);
 	}
-
-	if (!atmel_default_console_device)
-		printk(KERN_INFO "AT91: No default serial console defined.\n");
 }
 #else
 void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
 void __init at91_add_device_serial(void) {}
 #endif
 

index 7de81e6..c77d503 100644
@@ -239,18 +239,6 @@ static void __init at91sam9261_register_clocks(void)
 	clk_register(&hck1);
 }
 
-static struct clk_lookup console_clock_lookup;
-
-void __init at91sam9261_set_console_clock(int id)
-{
-	if (id >= ARRAY_SIZE(usart_clocks_lookups))
-		return;
-
-	console_clock_lookup.con_id = "usart";
-	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
-	clkdev_add(&console_clock_lookup);
-}
-
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */

index 4db961a..9295e90 100644
@@ -1051,14 +1051,6 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 		at91_uarts[portnr] = pdev;
 }
 
-void __init at91_set_serial_console(unsigned portnr)
-{
-	if (portnr < ATMEL_MAX_UART) {
-		atmel_default_console_device = at91_uarts[portnr];
-		at91sam9261_set_console_clock(at91_uarts[portnr]->id);
-	}
-}
-
 void __init at91_add_device_serial(void)
 {
 	int i;

@@ -1067,13 +1059,9 @@ void __init at91_add_device_serial(void)
 		if (at91_uarts[i])
 			platform_device_register(at91_uarts[i]);
 	}
-
-	if (!atmel_default_console_device)
-		printk(KERN_INFO "AT91: No default serial console defined.\n");
 }
 #else
 void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
 void __init at91_add_device_serial(void) {}
 #endif
 

index ef301be..7fae365 100644
@@ -255,18 +255,6 @@ static void __init at91sam9263_register_clocks(void)
 	clk_register(&pck3);
 }
 
-static struct clk_lookup console_clock_lookup;
-
-void __init at91sam9263_set_console_clock(int id)
-{
-	if (id >= ARRAY_SIZE(usart_clocks_lookups))
-		return;
-
-	console_clock_lookup.con_id = "usart";
-	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
-	clkdev_add(&console_clock_lookup);
-}
-
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */

index fe99206..dfe5bc0 100644
@@ -1461,14 +1461,6 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 		at91_uarts[portnr] = pdev;
 }
 
-void __init at91_set_serial_console(unsigned portnr)
-{
-	if (portnr < ATMEL_MAX_UART) {
-		atmel_default_console_device = at91_uarts[portnr];
-		at91sam9263_set_console_clock(at91_uarts[portnr]->id);
-	}
-}
-
 void __init at91_add_device_serial(void)
 {
 	int i;

@@ -1477,13 +1469,9 @@ void __init at91_add_device_serial(void)
 		if (at91_uarts[i])
 			platform_device_register(at91_uarts[i]);
 	}
-
-	if (!atmel_default_console_device)
-		printk(KERN_INFO "AT91: No default serial console defined.\n");
 }
 #else
 void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
 void __init at91_add_device_serial(void) {}
 #endif
 

index d222f83..f205449 100644
@@ -288,18 +288,6 @@ static void __init at91sam9g45_register_clocks(void)
 	clk_register(&pck1);
 }
 
-static struct clk_lookup console_clock_lookup;
-
-void __init at91sam9g45_set_console_clock(int id)
-{
-	if (id >= ARRAY_SIZE(usart_clocks_lookups))
-		return;
-
-	console_clock_lookup.con_id = "usart";
-	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
-	clkdev_add(&console_clock_lookup);
-}
-
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */

index 6b008ae..db2f88c2 100644
@@ -1741,14 +1741,6 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 		at91_uarts[portnr] = pdev;
 }
 
-void __init at91_set_serial_console(unsigned portnr)
-{
-	if (portnr < ATMEL_MAX_UART) {
-		atmel_default_console_device = at91_uarts[portnr];
-		at91sam9g45_set_console_clock(at91_uarts[portnr]->id);
-	}
-}
-
 void __init at91_add_device_serial(void)
 {
 	int i;

@@ -1757,13 +1749,9 @@ void __init at91_add_device_serial(void)
 		if (at91_uarts[i])
 			platform_device_register(at91_uarts[i]);
 	}
-
-	if (!atmel_default_console_device)
-		printk(KERN_INFO "AT91: No default serial console defined.\n");
 }
 #else
 void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
 void __init at91_add_device_serial(void) {}
 #endif
 

index d9f2774..e420085 100644
@@ -232,18 +232,6 @@ static void __init at91sam9rl_register_clocks(void)
 	clk_register(&pck1);
 }
 
-static struct clk_lookup console_clock_lookup;
-
-void __init at91sam9rl_set_console_clock(int id)
-{
-	if (id >= ARRAY_SIZE(usart_clocks_lookups))
-		return;
-
-	console_clock_lookup.con_id = "usart";
-	console_clock_lookup.clk = usart_clocks_lookups[id].clk;
-	clkdev_add(&console_clock_lookup);
-}
-
 /* --------------------------------------------------------------------
  *  GPIO
  * -------------------------------------------------------------------- */

index fe4ae22..9c0b148 100644
@@ -1192,14 +1192,6 @@ void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 		at91_uarts[portnr] = pdev;
 }
 
-void __init at91_set_serial_console(unsigned portnr)
-{
-	if (portnr < ATMEL_MAX_UART) {
-		atmel_default_console_device = at91_uarts[portnr];
-		at91sam9rl_set_console_clock(at91_uarts[portnr]->id);
-	}
-}
-
 void __init at91_add_device_serial(void)
 {
 	int i;

@@ -1208,13 +1200,9 @@ void __init at91_add_device_serial(void)
 		if (at91_uarts[i])
 			platform_device_register(at91_uarts[i]);
 	}
-
-	if (!atmel_default_console_device)
-		printk(KERN_INFO "AT91: No default serial console defined.\n");
 }
 #else
 void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_set_serial_console(unsigned portnr) {}
 void __init at91_add_device_serial(void) {}
 #endif
 

index 2628384..f43ad91 100644
@@ -58,9 +58,6 @@ static void __init onearm_init_early(void)
 	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
 			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
 			   | ATMEL_UART_RI);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata onearm_eth_data = {

index 161efba..7c7c682 100644
@@ -65,9 +65,6 @@ static void __init afeb9260_init_early(void)
 	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
 	at91_register_uart(AT91SAM9260_ID_US1, 2,
 			ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*

index c6d44ee..871717d 100644
@@ -52,9 +52,6 @@ static void __init cam60_init_early(void)
 
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*

index 59d9cf9..168b3fa 100644
@@ -52,9 +52,6 @@ static void __init carmeva_init_early(void)
 	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
 			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
 			   | ATMEL_UART_RI);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata carmeva_eth_data = {

index 5f3680e..4073e30 100644
@@ -77,9 +77,6 @@ static void __init cpu9krea_init_early(void)
 
 	/* USART5 on ttyS6. (Rx, Tx) */
 	at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*

index e094cc8..76c62ed 100644
@@ -78,9 +78,6 @@ static void __init cpuat91_init_early(void)
 	/* USART3 on ttyS4 (Rx, Tx, CTS, RTS) */
 	at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS |
 		ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata cpuat91_eth_data = {

index 1a1547b..d984435 100644
@@ -53,9 +53,6 @@ static void __init csb337_init_early(void)
 
 	/* DBGU on ttyS0 */
 	at91_register_uart(0, 0, 0);
-
-	/* make console=ttyS0 the default */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata csb337_eth_data = {

index f650bf3..0c9935d 100644
@@ -47,9 +47,6 @@ static void __init csb637_init_early(void)
 
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);
-
-	/* make console=ttyS0 (ie, DBGU) the default */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata csb637_eth_data = {

index d302ca3..a189b9f 100644
@@ -55,9 +55,6 @@ static void __init eb9200_init_early(void)
 
 	/* USART2 on ttyS2. (Rx, Tx) - IRDA */
 	at91_register_uart(AT91RM9200_ID_US2, 2, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata eb9200_eth_data = {

index 69966ce..307c530 100644
@@ -59,9 +59,6 @@ static void __init ecb_at91init_early(void)
 
 	/* USART0 on ttyS1. (Rx & Tx only) */
 	at91_register_uart(AT91RM9200_ID_US0, 1, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata ecb_at91eth_data = {

index f23aabe..7df6a9b 100644
@@ -43,9 +43,6 @@ static void __init eco920_init_early(void)
 
 	/* DBGU on ttyS0. (Rx & Tx only */
 	at91_register_uart(0, 0, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata eco920_eth_data = {

index 1815152..6dcc962 100644
@@ -44,9 +44,6 @@ static void __init flexibity_init_early(void)
 
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /* USB Host port */

index caf017f..bb07807 100644
@@ -93,9 +93,6 @@ static void __init foxg20_init_early(void)
 	/* USART5 on ttyS6. (Rx & Tx only) */
 	at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
 
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
-
 	/* Set the internal pull-up resistor on DRXD */
 	at91_set_A_periph(AT91_PIN_PB14, 1);
 

index efde1b2..3e858ed 100644
@@ -56,9 +56,6 @@ static void __init kafa_init_early(void)
 
 	/* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
 	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata kafa_eth_data = {

index 59b92aa..ccbc8be 100644
@@ -65,9 +65,6 @@ static void __init kb9202_init_early(void)
 
 	/* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */
 	at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata kb9202_eth_data = {

index 57d5f6a..c456fdc 100644
@@ -61,9 +61,6 @@ static void __init neocore926_init_early(void)
 
 	/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
 	at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*

index 59e35dd..4ca56cd 100644
@@ -56,9 +56,6 @@ static void __init picotux200_init_early(void)
 	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
 			  | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
 			  | ATMEL_UART_RI);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata picotux200_eth_data = {

index b6ed5ed..189d3fe 100644
@@ -66,10 +66,6 @@ static void __init ek_init_early(void)
 
 	/* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */
 	at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS1 (ie, USART0) */
-	at91_set_serial_console(1);
-
 }
 
 /*

index 01332aa..d5ce630 100644
@@ -61,9 +61,6 @@ static void __init dk_init_early(void)
 	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
 			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
 			   | ATMEL_UART_RI);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata dk_eth_data = {

index 11cbaa8..32d35cb 100644
@@ -61,9 +61,6 @@ static void __init ek_init_early(void)
 	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
 			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
 			   | ATMEL_UART_RI);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static struct macb_platform_data __initdata ek_eth_data = {

index af0750f..2c84463 100644
@@ -52,9 +52,6 @@ static void __init rsi_ews_init_early(void)
 	/* USART3 on ttyS4. (Rx, Tx, RTS) */
 	/* RS485 communication */
 	at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*

index e8b116b..dee44cb 100644
@@ -62,9 +62,6 @@ static void __init ek_init_early(void)
 
 	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
 	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*

index d5aec55..6da17b5 100644
@@ -65,9 +65,6 @@ static void __init ek_init_early(void)
 
 	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
 	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*

index c3f9944..e91c4af 100644
@@ -64,9 +64,6 @@ static void __init ek_init_early(void)
 
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*

index 2ffe50f..4424873 100644
@@ -63,9 +63,6 @@ static void __init ek_init_early(void)
 
 	/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
 	at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*

index 8923ec9..05f8467 100644
@@ -76,9 +76,6 @@ static void __init ek_init_early(void)
 
 	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
 	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*

index c88e908..be2ca19 100644
@@ -60,9 +60,6 @@ static void __init ek_init_early(void)
 	/* USART0 not connected on the -EK board */
 	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
 	at91_register_uart(AT91SAM9G45_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*

index b109ce2..23f383a 100644
@@ -48,9 +48,6 @@ static void __init ek_init_early(void)
 
 	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
 	at91_register_uart(AT91SAM9RL_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*

index ebc9d01..1a6774a 100644
@@ -46,7 +46,6 @@ static void __init snapper9260_init_early(void)
 
 	/* Debug on ttyS0 */
 	at91_register_uart(0, 0, 0);
-	at91_set_serial_console(0);
 
 	at91_register_uart(AT91SAM9260_ID_US0, 1,
 			   ATMEL_UART_CTS | ATMEL_UART_RTS);

index 7640049..38a7ca5 100644
@@ -39,9 +39,6 @@ void __init stamp9g20_init_early(void)
 
 	/* DGBU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 static void __init stamp9g20evb_init_early(void)

index b7483a3..ee482eb 100644
@@ -56,9 +56,6 @@ static void __init ek_init_early(void)
 
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*

index 38dd279..e94a04e 100644
@@ -75,9 +75,6 @@ static void __init yl9200_init_early(void)
 
 	/* USART3 on ttyS3. (Rx, Tx, RTS - RS485 interface) */
 	at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
 }
 
 /*

index dd9b346..0a60bf8 100644
@@ -40,17 +40,6 @@ extern struct sys_timer at91sam926x_timer;
 extern struct sys_timer at91x40_timer;
 
  /* Clocks */
-/*
- * function to specify the clock of the default console. As we do not
- * use the device/driver bus, the dev_name is not intialize. So we need
- * to link the clock to a specific con_id only "usart"
- */
-extern void __init at91rm9200_set_console_clock(int id);
-extern void __init at91sam9260_set_console_clock(int id);
-extern void __init at91sam9261_set_console_clock(int id);
-extern void __init at91sam9263_set_console_clock(int id);
-extern void __init at91sam9rl_set_console_clock(int id);
-extern void __init at91sam9g45_set_console_clock(int id);
 #ifdef CONFIG_AT91_PMC_UNIT
 extern int __init at91_clock_init(unsigned long main_clock);
 extern int __init at91_dt_clock_init(void);

index 49a8211..369afc2 100644
@@ -121,7 +121,6 @@ extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_de
 #define ATMEL_UART_RI	0x20
 
 extern void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins);
-extern void __init at91_set_serial_console(unsigned portnr);
 
 extern struct platform_device *atmel_default_console_device;
 

index f43ad91..271f994 100644
@@ -47,17 +47,6 @@ static void __init onearm_init_early(void)
 
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* USART1 on ttyS2 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
 }
 
 static struct macb_platform_data __initdata onearm_eth_data = {

@@ -79,6 +68,16 @@ static struct at91_udc_data __initdata onearm_udc_data = {
 static void __init onearm_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+	/* USART1 on ttyS2 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&onearm_eth_data);

index 7c7c682..b7d8aa7 100644
@@ -52,19 +52,6 @@ static void __init afeb9260_init_early(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1,
-			     ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR
-			   | ATMEL_UART_DCD | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2,
-			ATMEL_UART_CTS | ATMEL_UART_RTS);
 }
 
 /*

@@ -180,6 +167,18 @@ static struct at91_cf_data afeb9260_cf_data = {
 static void __init afeb9260_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1,
+			     ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR
+			   | ATMEL_UART_DCD | ATMEL_UART_RI);
+
+	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9260_ID_US1, 2,
+			ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&afeb9260_usbh_data);

index 871717d..29d3ef0 100644
@@ -49,9 +49,6 @@ static void __init cam60_init_early(void)
 {
 	/* Initialize processor: 10 MHz crystal */
 	at91_initialize(10000000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
 }
 
 /*

@@ -172,6 +169,8 @@ static void __init cam60_add_device_nand(void)
 static void __init cam60_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
 	at91_add_device_serial();
 	/* SPI */
 	at91_add_device_spi(cam60_spi_devices, ARRAY_SIZE(cam60_spi_devices));

index 168b3fa..44328a6 100644
@@ -44,14 +44,6 @@ static void __init carmeva_init_early(void)
 {
 	/* Initialize processor: 20.000 MHz crystal */
 	at91_initialize(20000000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
 }
 
 static struct macb_platform_data __initdata carmeva_eth_data = {

@@ -136,6 +128,13 @@ static struct gpio_led carmeva_leds[] = {
 static void __init carmeva_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&carmeva_eth_data);

61 lines not on this page · raw message

index 76c62ed..895cf2d 100644
@@ -59,25 +59,6 @@ static void __init cpuat91_init_early(void)
 
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS |
-		ATMEL_UART_RTS);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS |
-		ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR |
-		ATMEL_UART_DCD | ATMEL_UART_RI);
-
-	/* USART2 on ttyS3 (Rx, Tx) */
-	at91_register_uart(AT91RM9200_ID_US2, 3, 0);
-
-	/* USART3 on ttyS4 (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS |
-		ATMEL_UART_RTS);
 }
 
 static struct macb_platform_data __initdata cpuat91_eth_data = {

@@ -158,6 +139,24 @@ static struct platform_device *platform_devices[] __initdata = {
 static void __init cpuat91_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS |
+		ATMEL_UART_RTS);
+
+	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS |
+		ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR |
+		ATMEL_UART_DCD | ATMEL_UART_RI);
+
+	/* USART2 on ttyS3 (Rx, Tx) */
+	at91_register_uart(AT91RM9200_ID_US2, 3, 0);
+
+	/* USART3 on ttyS4 (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS |
+		ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* LEDs. */
 	at91_gpio_leds(cpuat91_leds, ARRAY_SIZE(cpuat91_leds));

index d984435..ad7f9f0 100644
@@ -50,9 +50,6 @@ static void __init csb337_init_early(void)
 
 	/* Setup the LEDs */
 	at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
-
-	/* DBGU on ttyS0 */
-	at91_register_uart(0, 0, 0);
 }
 
 static struct macb_platform_data __initdata csb337_eth_data = {

@@ -226,6 +223,8 @@ static struct gpio_led csb_leds[] = {
 static void __init csb337_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0 */
+	at91_register_uart(0, 0, 0);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&csb337_eth_data);

index 0c9935d..7c8b05a 100644
@@ -44,9 +44,6 @@ static void __init csb637_init_early(void)
 {
 	/* Initialize processor: 3.6864 MHz crystal */
 	at91_initialize(3686400);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
 }
 
 static struct macb_platform_data __initdata csb637_eth_data = {

@@ -115,6 +112,8 @@ static void __init csb637_board_init(void)
 	/* LED(s) */
 	at91_gpio_leds(csb_leds, ARRAY_SIZE(csb_leds));
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&csb637_eth_data);

index a189b9f..bd10172 100644
@@ -44,17 +44,6 @@ static void __init eb9200_init_early(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			| ATMEL_UART_RI);
-
-	/* USART2 on ttyS2. (Rx, Tx) - IRDA */
-	at91_register_uart(AT91RM9200_ID_US2, 2, 0);
 }
 
 static struct macb_platform_data __initdata eb9200_eth_data = {

@@ -98,6 +87,16 @@ static struct i2c_board_info __initdata eb9200_i2c_devices[] = {
 static void __init eb9200_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			| ATMEL_UART_RI);
+
+	/* USART2 on ttyS2. (Rx, Tx) - IRDA */
+	at91_register_uart(AT91RM9200_ID_US2, 2, 0);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&eb9200_eth_data);

index 307c530..2510825 100644
@@ -53,12 +53,6 @@ static void __init ecb_at91init_early(void)
 
 	/* Setup the LEDs */
 	at91_init_leds(AT91_PIN_PC7, AT91_PIN_PC7);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx & Tx only) */
-	at91_register_uart(AT91RM9200_ID_US0, 1, 0);
 }
 
 static struct macb_platform_data __initdata ecb_at91eth_data = {

@@ -149,6 +143,11 @@ static struct spi_board_info __initdata ecb_at91spi_devices[] = {
 static void __init ecb_at91board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx & Tx only) */
+	at91_register_uart(AT91RM9200_ID_US0, 1, 0);
 	at91_add_device_serial();
 
 	/* Ethernet */

index 7df6a9b..bebeae8 100644
@@ -40,9 +40,6 @@ static void __init eco920_init_early(void)
 
 	/* Setup the LEDs */
 	at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
-
-	/* DBGU on ttyS0. (Rx & Tx only */
-	at91_register_uart(0, 0, 0);
 }
 
 static struct macb_platform_data __initdata eco920_eth_data = {

@@ -100,6 +97,8 @@ static struct spi_board_info eco920_spi_devices[] = {
 
 static void __init eco920_board_init(void)
 {
+	/* DBGU on ttyS0. (Rx & Tx only */
+	at91_register_uart(0, 0, 0);
 	at91_add_device_serial();
 	at91_add_device_eth(&eco920_eth_data);
 	at91_add_device_usbh(&eco920_usbh_data);

index 6dcc962..47658f7 100644
@@ -41,9 +41,6 @@ static void __init flexibity_init_early(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
 }
 
 /* USB Host port */

@@ -140,6 +137,8 @@ static struct gpio_led flexibity_leds[] = {
 static void __init flexibity_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&flexibity_usbh_data);

80 lines not on this page · raw message

75 lines not on this page · raw message

index 3e858ed..f46b3eb 100644
@@ -50,12 +50,6 @@ static void __init kafa_init_early(void)
 
 	/* Set up the LEDs */
 	at91_init_leds(AT91_PIN_PB4, AT91_PIN_PB4);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
 }
 
 static struct macb_platform_data __initdata kafa_eth_data = {

@@ -77,6 +71,11 @@ static struct at91_udc_data __initdata kafa_udc_data = {
 static void __init kafa_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&kafa_eth_data);

index ccbc8be..e71b9e1 100644
@@ -53,18 +53,6 @@ static void __init kb9202_init_early(void)
 
 	/* Set up the LEDs */
 	at91_init_leds(AT91_PIN_PC19, AT91_PIN_PC18);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1 (Rx & Tx only) */
-	at91_register_uart(AT91RM9200_ID_US0, 1, 0);
-
-	/* USART1 on ttyS2 (Rx & Tx only) - IRDA (optional) */
-	at91_register_uart(AT91RM9200_ID_US1, 2, 0);
-
-	/* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */
-	at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
 }
 
 static struct macb_platform_data __initdata kb9202_eth_data = {

@@ -113,6 +101,17 @@ static struct atmel_nand_data __initdata kb9202_nand_data = {
 static void __init kb9202_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1 (Rx & Tx only) */
+	at91_register_uart(AT91RM9200_ID_US0, 1, 0);
+
+	/* USART1 on ttyS2 (Rx & Tx only) - IRDA (optional) */
+	at91_register_uart(AT91RM9200_ID_US1, 2, 0);
+
+	/* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */
+	at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&kb9202_eth_data);

index c456fdc..d2f4cc1 100644
@@ -55,12 +55,6 @@ static void __init neocore926_init_early(void)
 {
 	/* Initialize processor: 20 MHz crystal */
 	at91_initialize(20000000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
 }
 
 /*

@@ -338,6 +332,11 @@ static struct ac97c_platform_data neocore926_ac97_data = {
 static void __init neocore926_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 
 	/* USB Host */

index b4a12fc..7fe6383 100644
@@ -40,17 +40,6 @@
 static void __init pcontrol_g20_init_early(void)
 {
 	stamp9g20_init_early();
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback  A2 */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS
-						| ATMEL_UART_RTS);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) isolated RS485  X5 */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS
-						| ATMEL_UART_RTS);
-
-	/* USART2 on ttyS3. (Rx, Tx)  9bit-Bus  Multidrop-mode  X4 */
-	at91_register_uart(AT91SAM9260_ID_US4, 3, 0);
 }
 
 static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { {

@@ -199,6 +188,16 @@ static struct spi_board_info pcontrol_g20_spi_devices[] = {
 
 static void __init pcontrol_g20_board_init(void)
 {
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback  A2 */
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS
+						| ATMEL_UART_RTS);
+
+	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) isolated RS485  X5 */
+	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS
+						| ATMEL_UART_RTS);
+
+	/* USART2 on ttyS3. (Rx, Tx)  9bit-Bus  Multidrop-mode  X4 */
+	at91_register_uart(AT91SAM9260_ID_US4, 3, 0);
 	stamp9g20_board_init();
 	at91_add_device_usbh(&usbh_data);
 	at91_add_device_eth(&macb_data);

index 4ca56cd..b45c0a5 100644
@@ -48,14 +48,6 @@ static void __init picotux200_init_early(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			  | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			  | ATMEL_UART_RI);
 }
 
 static struct macb_platform_data __initdata picotux200_eth_data = {

@@ -103,6 +95,13 @@ static struct platform_device picotux200_flash = {
 static void __init picotux200_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			  | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			  | ATMEL_UART_RI);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&picotux200_eth_data);

index 189d3fe..0c61bf0 100644
@@ -52,20 +52,6 @@ static void __init ek_init_early(void)
 {
 	/* Initialize processor: 12.000 MHz crystal */
 	at91_initialize(12000000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
 }
 
 /*

@@ -231,6 +217,19 @@ static struct gpio_led ek_leds[] = {
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
+
+	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+	/* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&ek_usbh_data);

index d5ce630..4a0b097 100644
@@ -53,14 +53,6 @@ static void __init dk_init_early(void)
 
 	/* Setup the LEDs */
 	at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
 }
 
 static struct macb_platform_data __initdata dk_eth_data = {

@@ -188,6 +180,13 @@ static struct gpio_led dk_leds[] = {
 static void __init dk_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&dk_eth_data);

index 32d35cb..b687261 100644
@@ -53,14 +53,6 @@ static void __init ek_init_early(void)
 
 	/* Setup the LEDs */
 	at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
 }
 
 static struct macb_platform_data __initdata ek_eth_data = {

@@ -159,6 +151,13 @@ static struct gpio_led ek_leds[] = {
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&ek_eth_data);

index 2c84463..10d8730 100644
@@ -38,20 +38,6 @@ static void __init rsi_ews_init_early(void)
 
 	/* Setup the LEDs */
 	at91_init_leds(AT91_PIN_PB6, AT91_PIN_PB9);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	/* This one is for debugging */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	/* Dialin/-out modem interface */
-	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART3 on ttyS4. (Rx, Tx, RTS) */
-	/* RS485 communication */
-	at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS);
 }
 
 /*

@@ -202,6 +188,19 @@ static struct platform_device rsiews_nor_flash = {
 static void __init rsi_ews_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	/* This one is for debugging */
+	at91_register_uart(0, 0, 0);
+
+	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	/* Dialin/-out modem interface */
+	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
+
+	/* USART3 on ttyS4. (Rx, Tx, RTS) */
+	/* RS485 communication */
+	at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS);
 	at91_add_device_serial();
 	at91_set_gpio_output(AT91_PIN_PA21, 0);
 	/* Ethernet */

index dee44cb..5343dab 100644
@@ -51,17 +51,6 @@ static void __init ek_init_early(void)
 
 	/* Setup the LEDs */
 	at91_init_leds(AT91_PIN_PA9, AT91_PIN_PA6);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
 }
 
 /*

@@ -182,6 +171,16 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
+
+	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&ek_usbh_data);

index 6da17b5..7b3c391 100644
@@ -54,17 +54,6 @@ static void __init ek_init_early(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
 }
 
 /*

@@ -317,6 +306,16 @@ static void __init ek_add_device_buttons(void) {}
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
+
+	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&ek_usbh_data);

index e91c4af..4406f6b 100644
@@ -61,9 +61,6 @@ static void __init ek_init_early(void)
 
 	/* Setup the LEDs */
 	at91_init_leds(AT91_PIN_PA13, AT91_PIN_PA14);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
 }
 
 /*

@@ -574,6 +571,8 @@ static struct gpio_led ek_leds[] = {
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&ek_usbh_data);

index 4424873..983cb98 100644
@@ -57,12 +57,6 @@ static void __init ek_init_early(void)
 {
 	/* Initialize processor: 16.367 MHz crystal */
 	at91_initialize(16367660);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
 }
 
 /*

@@ -409,6 +403,11 @@ static struct at91_can_data ek_can_data = {
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&ek_usbh_data);

index 05f8467..3d61553 100644
@@ -65,17 +65,6 @@ static void __init ek_init_early(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
 }
 
 /*

@@ -369,6 +358,16 @@ static struct i2c_board_info __initdata ek_i2c_devices[] = {
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
+
+	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&ek_usbh_data);

index be2ca19..9a87f0b 100644
@@ -53,13 +53,6 @@ static void __init ek_init_early(void)
 {
 	/* Initialize processor: 12.000 MHz crystal */
 	at91_initialize(12000000);
-
-	/* DGBU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 not connected on the -EK board */
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9G45_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
 }
 
 /*

@@ -454,6 +447,12 @@ static struct platform_device *devices[] __initdata = {
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DGBU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 not connected on the -EK board */
+	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9G45_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB HS Host */
 	at91_add_device_usbh_ohci(&ek_usbh_hs_data);

index 23f383a..be3239f 100644
@@ -42,12 +42,6 @@ static void __init ek_init_early(void)
 {
 	/* Initialize processor: 12.000 MHz crystal */
 	at91_initialize(12000000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9RL_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
 }
 
 /*

@@ -293,6 +287,11 @@ static void __init ek_add_device_buttons(void) {}
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91SAM9RL_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB HS */
 	at91_add_device_usba(&ek_usba_udc_data);

index 1a6774a..9d446f1 100644
@@ -43,15 +43,6 @@
 static void __init snapper9260_init_early(void)
 {
 	at91_initialize(18432000);
-
-	/* Debug on ttyS0 */
-	at91_register_uart(0, 0, 0);
-
-	at91_register_uart(AT91SAM9260_ID_US0, 1,
-			   ATMEL_UART_CTS | ATMEL_UART_RTS);
-	at91_register_uart(AT91SAM9260_ID_US1, 2,
-			   ATMEL_UART_CTS | ATMEL_UART_RTS);
-	at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
 }
 
 static struct at91_usbh_data __initdata snapper9260_usbh_data = {

@@ -167,6 +158,14 @@ static void __init snapper9260_board_init(void)
 	snapper9260_i2c_isl1208.irq = gpio_to_irq(AT91_PIN_PA31);
 	i2c_register_board_info(0, &snapper9260_i2c_isl1208, 1);
 
+	/* Debug on ttyS0 */
+	at91_register_uart(0, 0, 0);
+
+	at91_register_uart(AT91SAM9260_ID_US0, 1,
+			   ATMEL_UART_CTS | ATMEL_UART_RTS);
+	at91_register_uart(AT91SAM9260_ID_US1, 2,
+			   ATMEL_UART_CTS | ATMEL_UART_RTS);
+	at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
 	at91_add_device_serial();
 	at91_add_device_usbh(&snapper9260_usbh_data);
 	at91_add_device_udc(&snapper9260_udc_data);

97 lines not on this page · raw message

index ee482eb..332ecd4 100644
@@ -53,9 +53,6 @@ static void __init ek_init_early(void)
 {
 	/* Initialize processor: 12.00 MHz crystal */
 	at91_initialize(12000000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
 }
 
 /*

@@ -322,6 +319,8 @@ static void __init ek_add_device_leds(void)
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
 	at91_add_device_serial();
 	/* USB Host */
 	at91_add_device_usbh(&ek_usbh_data);

index e94a04e..db8d25c 100644
@@ -61,20 +61,6 @@ static void __init yl9200_init_early(void)
 
 	/* Setup the LEDs D2=PB17 (timer), D3=PB16 (cpu) */
 	at91_init_leds(AT91_PIN_PB16, AT91_PIN_PB17);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			| ATMEL_UART_RI);
-
-	/* USART0 on ttyS2. (Rx & Tx only to JP3) */
-	at91_register_uart(AT91RM9200_ID_US0, 2, 0);
-
-	/* USART3 on ttyS3. (Rx, Tx, RTS - RS485 interface) */
-	at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_RTS);
 }
 
 /*

@@ -558,6 +544,19 @@ void __init yl9200_add_device_video(void) {}
 static void __init yl9200_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			| ATMEL_UART_RI);
+
+	/* USART0 on ttyS2. (Rx & Tx only to JP3) */
+	at91_register_uart(AT91RM9200_ID_US0, 2, 0);
+
+	/* USART3 on ttyS3. (Rx, Tx, RTS - RS485 interface) */
+	at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* Ethernet */
 	at91_add_device_eth(&yl9200_eth_data);

index ad7f9f0..cd81336 100644
@@ -47,9 +47,6 @@ static void __init csb337_init_early(void)
 {
 	/* Initialize processor: 3.6864 MHz crystal */
 	at91_initialize(3686400);
-
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
 }
 
 static struct macb_platform_data __initdata csb337_eth_data = {

@@ -222,6 +219,8 @@ static struct gpio_led csb_leds[] = {
 
 static void __init csb337_board_init(void)
 {
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
 	/* Serial */
 	/* DBGU on ttyS0 */
 	at91_register_uart(0, 0, 0);

index 2510825..89cc372 100644
@@ -50,9 +50,6 @@ static void __init ecb_at91init_early(void)
 
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PC7, AT91_PIN_PC7);
 }
 
 static struct macb_platform_data __initdata ecb_at91eth_data = {

@@ -142,6 +139,9 @@ static struct spi_board_info __initdata ecb_at91spi_devices[] = {
 
 static void __init ecb_at91board_init(void)
 {
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PC7, AT91_PIN_PC7);
+
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);

index bebeae8..558546c 100644
@@ -37,9 +37,6 @@ static void __init eco920_init_early(void)
 	at91rm9200_set_type(ARCH_REVISON_9200_PQFP);
 
 	at91_initialize(18432000);
-
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
 }
 
 static struct macb_platform_data __initdata eco920_eth_data = {

@@ -97,6 +94,8 @@ static struct spi_board_info eco920_spi_devices[] = {
 
 static void __init eco920_board_init(void)
 {
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
 	/* DBGU on ttyS0. (Rx & Tx only */
 	at91_register_uart(0, 0, 0);
 	at91_add_device_serial();

index f46b3eb..f260657 100644
@@ -47,9 +47,6 @@ static void __init kafa_init_early(void)
 
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* Set up the LEDs */
-	at91_init_leds(AT91_PIN_PB4, AT91_PIN_PB4);
 }
 
 static struct macb_platform_data __initdata kafa_eth_data = {

@@ -70,6 +67,9 @@ static struct at91_udc_data __initdata kafa_udc_data = {
 
 static void __init kafa_board_init(void)
 {
+	/* Set up the LEDs */
+	at91_init_leds(AT91_PIN_PB4, AT91_PIN_PB4);
+
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);

index e71b9e1..ba39db5 100644
@@ -50,9 +50,6 @@ static void __init kb9202_init_early(void)
 
 	/* Initialize processor: 10 MHz crystal */
 	at91_initialize(10000000);
-
-	/* Set up the LEDs */
-	at91_init_leds(AT91_PIN_PC19, AT91_PIN_PC18);
 }
 
 static struct macb_platform_data __initdata kb9202_eth_data = {

@@ -100,6 +97,9 @@ static struct atmel_nand_data __initdata kb9202_nand_data = {
 
 static void __init kb9202_board_init(void)
 {
+	/* Set up the LEDs */
+	at91_init_leds(AT91_PIN_PC19, AT91_PIN_PC18);
+
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);

index 4a0b097..afd7a47 100644
@@ -50,9 +50,6 @@ static void __init dk_init_early(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2);
 }
 
 static struct macb_platform_data __initdata dk_eth_data = {

@@ -179,6 +176,9 @@ static struct gpio_led dk_leds[] = {
 
 static void __init dk_board_init(void)
 {
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2);
+
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);

index b687261..78ffc83 100644
@@ -50,9 +50,6 @@ static void __init ek_init_early(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);
 }
 
 static struct macb_platform_data __initdata ek_eth_data = {

@@ -150,6 +147,9 @@ static struct gpio_led ek_leds[] = {
 
 static void __init ek_board_init(void)
 {
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);
+
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);

index 10d8730..24ab9be 100644
@@ -35,9 +35,6 @@ static void __init rsi_ews_init_early(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PB6, AT91_PIN_PB9);
 }
 
 /*

@@ -187,6 +184,9 @@ static struct platform_device rsiews_nor_flash = {
  */
 static void __init rsi_ews_board_init(void)
 {
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PB6, AT91_PIN_PB9);
+
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	/* This one is for debugging */

index 5343dab..cdd21f2 100644
@@ -48,9 +48,6 @@ static void __init ek_init_early(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PA9, AT91_PIN_PA6);
 }
 
 /*

@@ -170,6 +167,9 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 
 static void __init ek_board_init(void)
 {
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PA9, AT91_PIN_PA6);
+
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);

index 4406f6b..065b5ee 100644
@@ -58,9 +58,6 @@ static void __init ek_init_early(void)
 {
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PA13, AT91_PIN_PA14);
 }
 
 /*

@@ -570,6 +567,9 @@ static struct gpio_led ek_leds[] = {
 
 static void __init ek_board_init(void)
 {
+	/* Setup the LEDs */
+	at91_init_leds(AT91_PIN_PA13, AT91_PIN_PA14);
+
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);

index db8d25c..d56665e 100644
@@ -58,9 +58,6 @@ static void __init yl9200_init_early(void)
 
 	/* Initialize processor: 18.432 MHz crystal */
 	at91_initialize(18432000);
-
-	/* Setup the LEDs D2=PB17 (timer), D3=PB16 (cpu) */
-	at91_init_leds(AT91_PIN_PB16, AT91_PIN_PB17);
 }
 
 /*

@@ -543,6 +540,9 @@ void __init yl9200_add_device_video(void) {}
 
 static void __init yl9200_board_init(void)
 {
+	/* Setup the LEDs D2=PB17 (timer), D3=PB16 (cpu) */
+	at91_init_leds(AT91_PIN_PB16, AT91_PIN_PB17);
+
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);

index f630250..1bfaad6 100644
@@ -261,7 +261,12 @@ static int at91_pm_enter(suspend_state_t state)
 			 * For ARM 926 based chips, this requirement is weaker
 			 * as at91sam9 can access a RAM in self-refresh mode.
 			 */
-			at91_standby();
+			if (cpu_is_at91rm9200())
+				at91rm9200_standby();
+			else if (cpu_is_at91sam9g45())
+				at91sam9g45_standby();
+			else
+				at91sam9_standby();
 			break;
 
 		case PM_SUSPEND_ON:

@@ -307,10 +312,9 @@ static int __init at91_pm_init(void)
 
 	pr_info("AT91: Power Management%s\n", (slow_clock ? " (with slow clock mode)" : ""));
 
-#ifdef CONFIG_ARCH_AT91RM9200
 	/* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh. */
-	at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
-#endif
+	if (cpu_is_at91rm9200())
+		at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
 
 	suspend_set_ops(&at91_pm_ops);
 

index 89f56f3..1b4865e 100644
@@ -12,7 +12,6 @@
 #define __ARCH_ARM_MACH_AT91_PM
 
 #include <mach/at91_ramc.h>
-#ifdef CONFIG_ARCH_AT91RM9200
 #include <mach/at91rm9200_sdramc.h>
 
 /*

@@ -43,10 +42,6 @@ static inline void at91rm9200_standby(void)
 		  "r" (lpr));
 }
 
-#define at91_standby at91rm9200_standby
-
-#elif defined(CONFIG_ARCH_AT91SAM9G45)
-
 /* We manage both DDRAM/SDRAM controllers, we need more than one value to
  * remember.
  */

@@ -75,10 +70,6 @@ static inline void at91sam9g45_standby(void)
 	at91_ramc_write(1, AT91_DDRSDRC_LPR, saved_lpr1);
 }
 
-#define at91_standby at91sam9g45_standby
-
-#else
-
 #ifdef CONFIG_ARCH_AT91SAM9263
 /*
  * FIXME either or both the SDRAM controllers (EB0, EB1) might be in use;

@@ -102,8 +93,4 @@ static inline void at91sam9_standby(void)
 	at91_ramc_write(0, AT91_SDRAMC_LPR, saved_lpr);
 }
 
-#define at91_standby at91sam9_standby
-
-#endif
-
 #endif

index ece1f9a..0c63815 100644
@@ -21,6 +21,7 @@
 #include <linux/export.h>
 #include <asm/proc-fns.h>
 #include <asm/cpuidle.h>
+#include <mach/cpu.h>
 
 #include "pm.h"
 

@@ -33,7 +34,12 @@ static int at91_enter_idle(struct cpuidle_device *dev,
 			struct cpuidle_driver *drv,
 			       int index)
 {
-	at91_standby();
+	if (cpu_is_at91rm9200())
+		at91rm9200_standby();
+	else if (cpu_is_at91sam9g45())
+		at91sam9g45_standby();
+	else
+		at91sam9_standby();
 
 	return index;
 }

index f630250..1bfaad6 100644
@@ -261,7 +261,12 @@ static int at91_pm_enter(suspend_state_t state)
 			 * For ARM 926 based chips, this requirement is weaker
 			 * as at91sam9 can access a RAM in self-refresh mode.
 			 */
-			at91_standby();
+			if (cpu_is_at91rm9200())
+				at91rm9200_standby();
+			else if (cpu_is_at91sam9g45())
+				at91sam9g45_standby();
+			else
+				at91sam9_standby();
 			break;
 
 		case PM_SUSPEND_ON:

@@ -307,10 +312,9 @@ static int __init at91_pm_init(void)
 
 	pr_info("AT91: Power Management%s\n", (slow_clock ? " (with slow clock mode)" : ""));
 
-#ifdef CONFIG_ARCH_AT91RM9200
 	/* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh. */
-	at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
-#endif
+	if (cpu_is_at91rm9200())
+		at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
 
 	suspend_set_ops(&at91_pm_ops);
 

index 89f56f3..1b4865e 100644
@@ -12,7 +12,6 @@
 #define __ARCH_ARM_MACH_AT91_PM
 
 #include <mach/at91_ramc.h>
-#ifdef CONFIG_ARCH_AT91RM9200
 #include <mach/at91rm9200_sdramc.h>
 
 /*

@@ -43,10 +42,6 @@ static inline void at91rm9200_standby(void)
 		  "r" (lpr));
 }
 
-#define at91_standby at91rm9200_standby
-
-#elif defined(CONFIG_ARCH_AT91SAM9G45)
-
 /* We manage both DDRAM/SDRAM controllers, we need more than one value to
  * remember.
  */

@@ -75,10 +70,6 @@ static inline void at91sam9g45_standby(void)
 	at91_ramc_write(1, AT91_DDRSDRC_LPR, saved_lpr1);
 }
 
-#define at91_standby at91sam9g45_standby
-
-#else
-
 #ifdef CONFIG_ARCH_AT91SAM9263
 /*
  * FIXME either or both the SDRAM controllers (EB0, EB1) might be in use;

@@ -102,8 +93,4 @@ static inline void at91sam9_standby(void)
 	at91_ramc_write(0, AT91_SDRAMC_LPR, saved_lpr);
 }
 
-#define at91_standby at91sam9_standby
-
-#endif
-
 #endif

index 0118c33..73d2fd2 100644
@@ -54,6 +54,7 @@
 #define ARCH_REVISON_9200_BGA	(0 << 0)
 #define ARCH_REVISON_9200_PQFP	(1 << 0)
 
+#ifndef __ASSEMBLY__
 enum at91_soc_type {
 	/* 920T */
 	AT91_SOC_RM9200,

@@ -106,7 +107,7 @@ static inline int at91_soc_is_detected(void)
 	return at91_soc_initdata.type != AT91_SOC_NONE;
 }
 
-#ifdef CONFIG_ARCH_AT91RM9200
+#ifdef CONFIG_SOC_AT91RM9200
 #define cpu_is_at91rm9200()	(at91_soc_initdata.type == AT91_SOC_RM9200)
 #define cpu_is_at91rm9200_bga()	(at91_soc_initdata.subtype == AT91_SOC_RM9200_BGA)
 #define cpu_is_at91rm9200_pqfp() (at91_soc_initdata.subtype == AT91_SOC_RM9200_PQFP)

@@ -116,45 +117,37 @@ static inline int at91_soc_is_detected(void)
 #define cpu_is_at91rm9200_pqfp() (0)
 #endif
 
-#ifdef CONFIG_ARCH_AT91SAM9260
+#ifdef CONFIG_SOC_AT91SAM9260
 #define cpu_is_at91sam9xe()	(at91_soc_initdata.subtype == AT91_SOC_SAM9XE)
 #define cpu_is_at91sam9260()	(at91_soc_initdata.type == AT91_SOC_SAM9260)
+#define cpu_is_at91sam9g20()	(at91_soc_initdata.type == AT91_SOC_SAM9G20)
 #else
 #define cpu_is_at91sam9xe()	(0)
 #define cpu_is_at91sam9260()	(0)
-#endif
-
-#ifdef CONFIG_ARCH_AT91SAM9G20
-#define cpu_is_at91sam9g20()	(at91_soc_initdata.type == AT91_SOC_SAM9G20)
-#else
 #define cpu_is_at91sam9g20()	(0)
 #endif
 
-#ifdef CONFIG_ARCH_AT91SAM9261
+#ifdef CONFIG_SOC_AT91SAM9261
 #define cpu_is_at91sam9261()	(at91_soc_initdata.type == AT91_SOC_SAM9261)
-#else
-#define cpu_is_at91sam9261()	(0)
-#endif
-
-#ifdef CONFIG_ARCH_AT91SAM9G10
 #define cpu_is_at91sam9g10()	(at91_soc_initdata.type == AT91_SOC_SAM9G10)
 #else
+#define cpu_is_at91sam9261()	(0)
 #define cpu_is_at91sam9g10()	(0)
 #endif
 
-#ifdef CONFIG_ARCH_AT91SAM9263
+#ifdef CONFIG_SOC_AT91SAM9263
 #define cpu_is_at91sam9263()	(at91_soc_initdata.type == AT91_SOC_SAM9263)
 #else
 #define cpu_is_at91sam9263()	(0)
 #endif
 
-#ifdef CONFIG_ARCH_AT91SAM9RL
+#ifdef CONFIG_SOC_AT91SAM9RL
 #define cpu_is_at91sam9rl()	(at91_soc_initdata.type == AT91_SOC_SAM9RL)
 #else
 #define cpu_is_at91sam9rl()	(0)
 #endif
 
-#ifdef CONFIG_ARCH_AT91SAM9G45
+#ifdef CONFIG_SOC_AT91SAM9G45
 #define cpu_is_at91sam9g45()	(at91_soc_initdata.type == AT91_SOC_SAM9G45)
 #define cpu_is_at91sam9g45es()	(at91_soc_initdata.subtype == AT91_SOC_SAM9G45ES)
 #define cpu_is_at91sam9m10()	(at91_soc_initdata.subtype == AT91_SOC_SAM9M10)

@@ -168,7 +161,7 @@ static inline int at91_soc_is_detected(void)
 #define cpu_is_at91sam9m11()	(0)
 #endif
 
-#ifdef CONFIG_ARCH_AT91SAM9X5
+#ifdef CONFIG_SOC_AT91SAM9X5
 #define cpu_is_at91sam9x5()	(at91_soc_initdata.type == AT91_SOC_SAM9X5)
 #define cpu_is_at91sam9g15()	(at91_soc_initdata.subtype == AT91_SOC_SAM9G15)
 #define cpu_is_at91sam9g35()	(at91_soc_initdata.subtype == AT91_SOC_SAM9G35)

@@ -189,5 +182,6 @@ static inline int at91_soc_is_detected(void)
  * definitions may reduce clutter in common drivers.
  */
 #define cpu_is_at32ap7000()	(0)
+#endif /* __ASSEMBLY__ */
 
 #endif /* __MACH_CPU_H__ */

index 1b4865e..38f467c 100644
@@ -70,7 +70,7 @@ static inline void at91sam9g45_standby(void)
 	at91_ramc_write(1, AT91_DDRSDRC_LPR, saved_lpr1);
 }
 
-#ifdef CONFIG_ARCH_AT91SAM9263
+#ifdef CONFIG_SOC_AT91SAM9263
 /*
  * FIXME either or both the SDRAM controllers (EB0, EB1) might be in use;
  * handle those cases both here and in the Suspend-To-RAM support.

index 5db4aa4..683dddf 100644
@@ -26,30 +26,30 @@ static inline int at91_soc_is_enabled(void)
 	return at91_boot_soc.init != NULL;
 }
 
-#if !defined(CONFIG_ARCH_AT91RM9200)
+#if !defined(CONFIG_SOC_AT91RM9200)
 #define at91rm9200_soc	at91_boot_soc
 #endif
 
-#if !(defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20))
+#if !defined(CONFIG_SOC_AT91SAM9260)
 #define at91sam9260_soc	at91_boot_soc
 #endif
 
-#if !(defined(CONFIG_ARCH_AT91SAM9261) || defined(CONFIG_ARCH_AT91SAM9G10))
+#if !defined(CONFIG_SOC_AT91SAM9261)
 #define at91sam9261_soc	at91_boot_soc
 #endif
 
-#if !defined(CONFIG_ARCH_AT91SAM9263)
+#if !defined(CONFIG_SOC_AT91SAM9263)
 #define at91sam9263_soc	at91_boot_soc
 #endif
 
-#if !defined(CONFIG_ARCH_AT91SAM9G45)
+#if !defined(CONFIG_SOC_AT91SAM9G45)
 #define at91sam9g45_soc	at91_boot_soc
 #endif
 
-#if !defined(CONFIG_ARCH_AT91SAM9RL)
+#if !defined(CONFIG_SOC_AT91SAM9RL)
 #define at91sam9rl_soc	at91_boot_soc
 #endif
 
-#if !defined(CONFIG_ARCH_AT91SAM9X5)
+#if !defined(CONFIG_SOC_AT91SAM9X5)
 #define at91sam9x5_soc	at91_boot_soc
 #endif

index c18d4d3..78a4a61 100644
@@ -1,12 +1,10 @@
 /*
- *  Setup code for AT91SAM Evaluation Kits with Device Tree support
+ * Setup code for AT91SAM Evaluation Kits with Device Tree support
  *
- *  Covers: * AT91SAM9G45-EKES  board
- *          * AT91SAM9M10-EKES  board
- *          * AT91SAM9M10G45-EK board
+ * Copyright (C) 2011-2012 Atmel,
+ *		 2011-2012 Nicolas Ferre <[email protected]>
  *
- *  Copyright (C) 2011 Atmel,
- *                2011 Nicolas Ferre <[email protected]>
+ * Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
  *
  * Licensed under GPLv2 or later.
  */

@@ -49,9 +47,7 @@ static void __init at91_dt_device_init(void)
 }
 
 static const char *at91_dt_board_compat[] __initdata = {
-	"atmel,at91sam9m10g45ek",
-	"atmel,at91sam9x5ek",
-	"calao,usb-a9g20",
+	"atmel,at91sam9",
 	NULL
 };