imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition

From: Fabio Estevam <[email protected]>

According to include/i2c.h:

"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

---
 include/configs/imx31_phycore.h |    1 -
 1 files changed, 0 insertions(+), 1 deletions(-)

index 3153eb5..b3244b9 100644
@@ -56,7 +56,6 @@
 #define CONFIG_I2C_MXC
 #define CONFIG_SYS_I2C_MX31_PORT2
 #define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		0xfe
 
 #define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE		UART1_BASE

1.7.1

From: Fabio Estevam <[email protected]>

According to include/i2c.h:

"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

---
 include/configs/mx35pdk.h |    1 -
 1 files changed, 0 insertions(+), 1 deletions(-)

index bd57baa..5f75018 100644
@@ -59,7 +59,6 @@
 #define CONFIG_I2C_MXC
 #define CONFIG_SYS_I2C_MX35_PORT1
 #define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		0xfe
 #define CONFIG_MXC_SPI
 #define CONFIG_MXC_GPIO
 

1.7.1

According to include/i2c.h:

"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

---
 include/configs/mx53ard.h |    1 -
 1 files changed, 0 insertions(+), 1 deletions(-)

index f48a41e..f879edc 100644
@@ -52,7 +52,6 @@
 #define CONFIG_I2C_MXC
 #define CONFIG_SYS_I2C_MX53_PORT2
 #define CONFIG_SYS_I2C_SPEED            100000
-#define CONFIG_SYS_I2C_SLAVE            0xfe
 
 /* MMC Configs */
 #define CONFIG_FSL_ESDHC

1.7.1

From: Fabio Estevam <[email protected]>

According to include/i2c.h:

"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

---
 include/configs/mx53evk.h |    1 -
 1 files changed, 0 insertions(+), 1 deletions(-)

index a77e5b2..2acefe9 100644
@@ -55,7 +55,6 @@
 #define CONFIG_I2C_MXC
 #define CONFIG_SYS_I2C_MX53_PORT2       1
 #define CONFIG_SYS_I2C_SPEED            100000
-#define CONFIG_SYS_I2C_SLAVE            0xfe
 
 /* PMIC Configs */
 #define CONFIG_PMIC

1.7.1

From: Fabio Estevam <[email protected]>

According to include/i2c.h:

"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

---
 include/configs/mx53loco.h |    1 -
 1 files changed, 0 insertions(+), 1 deletions(-)

index 7d782e2..7c45647 100644
@@ -92,7 +92,6 @@
 #define CONFIG_I2C_MXC
 #define CONFIG_SYS_I2C_MX53_PORT1
 #define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		0xfe
 
 /* PMIC Controller */
 #define CONFIG_PMIC

1.7.1

From: Fabio Estevam <[email protected]>

According to include/i2c.h:

"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

---
 include/configs/mx53smd.h |    1 -
 1 files changed, 0 insertions(+), 1 deletions(-)

index a04db3f..61edd7f 100644
@@ -52,7 +52,6 @@
 #define CONFIG_I2C_MXC
 #define CONFIG_SYS_I2C_MX53_PORT2
 #define CONFIG_SYS_I2C_SPEED            100000
-#define CONFIG_SYS_I2C_SLAVE            0xfe
 
 /* MMC Configs */
 #define CONFIG_FSL_ESDHC

1.7.1

Whole series applied to u-boot-imx, thanks.

Best regards,
Stefano Babic

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================