arm : Atmel : add at91sam9x5ek board support

Add at91sam9x5ek board support, this board support the following SoCs
AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35

Using at91sam9x5ek_nandflash to configure for the board Now only supports NAND with software ECC boot up

This patch is based on git://git.denx.de/u-boot-atmel.git

Signed-off-by Bo Shen <[email protected]>

---
Changed since v1
Modify the code according to Andreas's suggestion

---
 MAINTAINERS                                        |    3 +
 arch/arm/cpu/arm926ejs/at91/Makefile               |    1 +
 arch/arm/cpu/arm926ejs/at91/at91sam9x5_devices.c   |  237 +++++++++++++++
 arch/arm/cpu/arm926ejs/at91/clock.c                |    7 +-
 arch/arm/include/asm/arch-at91/at91sam9_matrix.h   |    2 +
 arch/arm/include/asm/arch-at91/at91sam9x5.h        |  172 +++++++++++
 arch/arm/include/asm/arch-at91/at91sam9x5_matrix.h |   91 ++++++
 arch/arm/include/asm/arch-at91/hardware.h          |    2 +
 board/atmel/at91sam9x5ek/Makefile                  |   48 +++
 board/atmel/at91sam9x5ek/at91sam9x5ek.c            |  306 ++++++++++++++++++++
 board/atmel/at91sam9x5ek/config.mk                 |    1 +
 boards.cfg                                         |    1 +
 drivers/net/macb.c                                 |    4 +-
 drivers/serial/atmel_usart.h                       |    7 +-
 include/configs/at91sam9x5ek.h                     |  201 +++++++++++++
 15 files changed, 1077 insertions(+), 6 deletions(-)
 create mode 100644 arch/arm/cpu/arm926ejs/at91/at91sam9x5_devices.c
 create mode 100644 arch/arm/include/asm/arch-at91/at91sam9x5.h
 create mode 100644 arch/arm/include/asm/arch-at91/at91sam9x5_matrix.h
 create mode 100644 board/atmel/at91sam9x5ek/Makefile
 create mode 100644 board/atmel/at91sam9x5ek/at91sam9x5ek.c
 create mode 100644 board/atmel/at91sam9x5ek/config.mk
 create mode 100644 include/configs/at91sam9x5ek.h

MAINTAINERS +3 -0

index 6438e1c..a2fccbf 100644
@@ -660,6 +660,9 @@ Sedji Gaouaou<[email protected]>
 	at91sam9g10ek		ARM926EJS (AT91SAM9G10 SoC)
 	at91sam9m10g45ek	ARM926EJS (AT91SAM9G45 SoC)
 
+Bo Shen <[email protected]>
+	at91sam9x5ek		ARM926EJS (AT91SAM9G15,G25,G35,X25,X35 SoC)
+
 Simon Guinot <[email protected]>
 
 	inetspace_v2	ARM926EJS (Kirkwood SoC)

arch/arm/cpu/arm926ejs/at91/Makefile +1 -0

index f333753..346e58f 100644
@@ -35,6 +35,7 @@ COBJS-$(CONFIG_AT91SAM9263)	+= at91sam9263_devices.o
 COBJS-$(CONFIG_AT91SAM9RL)	+= at91sam9rl_devices.o
 COBJS-$(CONFIG_AT91SAM9M10G45)	+= at91sam9m10g45_devices.o
 COBJS-$(CONFIG_AT91SAM9G45)	+= at91sam9m10g45_devices.o
+COBJS-$(CONFIG_AT91SAM9X5)	+= at91sam9x5_devices.o
 COBJS-$(CONFIG_AT91_EFLASH)	+= eflash.o
 COBJS-$(CONFIG_AT91_LED)	+= led.o
 COBJS-y += clock.o

arch/arm/cpu/arm926ejs/at91/at91sam9x5_devices.c new file +30 -0

new file mode 100644
index 0000000..2c99a4e
@@ -0,0 +1,237 @@
+/*
+ * Copyright (C) 2012 Atmel Corporation
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/gpio.h>
+#include <asm/io.h>
+#include <../drivers/serial/atmel_usart.h>
+
+unsigned int get_chip_id(void)

arch/arm/cpu/arm926ejs/at91/at91sam9x5_devices.c new file +193 -0

+
+unsigned int has_emac1()
+{
+	return cpu_is_at91sam9x25();
+}
+
+unsigned int has_emac0()
+{
+	return !(cpu_is_at91sam9g15());
+}
+
+unsigned int has_lcdc()
+{
+	return cpu_is_at91sam9g15() || cpu_is_at91sam9g35()
+		|| cpu_is_at91sam9x35();
+}
+
+char *get_cpu_name()
+{
+	unsigned int extension_id = get_extension_chip_id();
+
+	if (cpu_is_at91sam9x5()) {
+		switch (extension_id) {
+		case ARCH_EXID_AT91SAM9G15:
+			return CONFIG_SYS_AT91_G15_CPU_NAME;
+		case ARCH_EXID_AT91SAM9G25:
+			return CONFIG_SYS_AT91_G25_CPU_NAME;
+		case ARCH_EXID_AT91SAM9G35:
+			return CONFIG_SYS_AT91_G35_CPU_NAME;
+		case ARCH_EXID_AT91SAM9X25:
+			return CONFIG_SYS_AT91_X25_CPU_NAME;
+		case ARCH_EXID_AT91SAM9X35:
+			return CONFIG_SYS_AT91_X35_CPU_NAME;
+		default:
+			return CONFIG_SYS_AT91_UNKNOWN_CPU;
+		}
+	} else {
+		return CONFIG_SYS_AT91_UNKNOWN_CPU;
+	}
+}
+
+void at91_seriald_hw_init(void)
+{
+	at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
+
+	at91_set_a_periph(AT91_PIO_PORTA, 9, 0);	/* DRXD */
+	at91_set_a_periph(AT91_PIO_PORTA, 10, 1);	/* DTXD */
+
+	writel(1 << ATMEL_ID_SYS, &pmc->pcer);
+}
+
+void at91_serial0_hw_init(void)
+{
+	at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
+
+	at91_set_a_periph(AT91_PIO_PORTA, 0, 1);	/* TXD */
+	at91_set_a_periph(AT91_PIO_PORTA, 1, 0);	/* RXD */
+
+	writel(1 << ATMEL_ID_USART0, &pmc->pcer);
+}
+
+void at91_serial1_hw_init(void)
+{
+	at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
+
+	at91_set_a_periph(AT91_PIO_PORTA, 5, 1);	/* TXD */
+	at91_set_a_periph(AT91_PIO_PORTA, 6, 0);	/* RXD */
+
+	writel(1 << ATMEL_ID_USART1, &pmc->pcer);
+}
+
+void at91_serial2_hw_init(void)
+{
+	at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
+
+	at91_set_a_periph(AT91_PIO_PORTA, 7, 1);	/* TXD */
+	at91_set_a_periph(AT91_PIO_PORTA, 8, 0);	/* RXD */
+
+	writel(1 << ATMEL_ID_USART2, &pmc->pcer);
+}
+
+#ifdef CONFIG_ATMEL_SPI
+void at91_spi0_hw_init(unsigned long cs_mask)
+{
+	at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_PMC_BASE;
+
+	at91_set_a_periph(AT91_PIO_PORTA, 11, 0);	/* SPI0_MISO */
+	at91_set_a_periph(AT91_PIO_PORTA, 12, 0);	/* SPI0_MOSI */
+	at91_set_a_periph(AT91_PIO_PORTA, 13, 0);	/* SPI0_SPCK */
+
+	/* Enable clock */
+	writel(1 << ATMEL_ID_SPI0, &pmc->pcer);
+
+	if (cs_mask & (1 << 0))
+		at91_set_a_periph(AT91_PIO_PORTA, 14, 0);
+	if (cs_mask & (1 << 1))
+		at91_set_b_periph(AT91_PIO_PORTA, 7, 0);
+	if (cs_mask & (1 << 2))
+		at91_set_b_periph(AT91_PIO_PORTA, 1, 0);
+	if (cs_mask & (1 << 3))
+		at91_set_b_periph(AT91_PIO_PORTB, 3, 0);
+	if (cs_mask & (1 << 4))
+		at91_set_pio_output(AT91_PIO_PORTA, 14, 0);
+	if (cs_mask & (1 << 5))
+		at91_set_pio_output(AT91_PIO_PORTA, 7, 0);
+	if (cs_mask & (1 << 6))
+		at91_set_pio_output(AT91_PIO_PORTA, 1, 0);
+	if (cs_mask & (1 << 7))
+		at91_set_pio_output(AT91_PIO_PORTB, 3, 0);
+}
+
+void at91_spi1_hw_init(unsigned long cs_mask)
+{
+	at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_PMC_BASE;
+
+	at91_set_b_periph(AT91_PIO_PORTA, 21, 0);	/* SPI1_MISO */
+	at91_set_b_periph(AT91_PIO_PORTA, 22, 0);	/* SPI1_MOSI */
+	at91_set_b_periph(AT91_PIO_PORTA, 23, 0);	/* SPI1_SPCK */
+
+	/* Enable clock */
+	writel(1 << ATMEL_ID_SPI1, &pmc->pcer);
+
+	if (cs_mask & (1 << 0))
+		at91_set_b_periph(AT91_PIO_PORTA, 8, 0);
+	if (cs_mask & (1 << 1))
+		at91_set_b_periph(AT91_PIO_PORTA, 0, 0);
+	if (cs_mask & (1 << 2))
+		at91_set_b_periph(AT91_PIO_PORTA, 31, 0);
+	if (cs_mask & (1 << 3))
+		at91_set_b_periph(AT91_PIO_PORTA, 30, 0);
+	if (cs_mask & (1 << 4))
+		at91_set_pio_output(AT91_PIO_PORTA, 8, 0);
+	if (cs_mask & (1 << 5))
+		at91_set_pio_output(AT91_PIO_PORTA, 0, 0);
+	if (cs_mask & (1 << 6))
+		at91_set_pio_output(AT91_PIO_PORTA, 31, 0);
+	if (cs_mask & (1 << 7))
+		at91_set_pio_output(AT91_PIO_PORTA, 30, 0);
+}
+#endif
+
+#ifdef CONFIG_MACB
+void at91_macb_hw_init(void)
+{
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
+	if (has_emac0()) {
+		/* Enable EMAC0 clock */
+		writel(1 << ATMEL_ID_EMAC0, &pmc->pcer);
+		/* EMAC0 pins setup */
+		at91_set_a_periph(AT91_PIO_PORTB, 4, 0);	/* ETXCK */
+		at91_set_a_periph(AT91_PIO_PORTB, 3, 0);	/* ERXDV */
+		at91_set_a_periph(AT91_PIO_PORTB, 0, 0);	/* ERX0 */
+		at91_set_a_periph(AT91_PIO_PORTB, 1, 0);	/* ERX1 */
+		at91_set_a_periph(AT91_PIO_PORTB, 2, 0);	/* ERXER */
+		at91_set_a_periph(AT91_PIO_PORTB, 7, 0);	/* ETXEN */
+		at91_set_a_periph(AT91_PIO_PORTB, 9, 0);	/* ETX0 */
+		at91_set_a_periph(AT91_PIO_PORTB, 10, 0);	/* ETX1 */
+		at91_set_a_periph(AT91_PIO_PORTB, 5, 0);	/* EMDIO */
+		at91_set_a_periph(AT91_PIO_PORTB, 6, 0);	/* EMDC */
+	}
+
+	if (has_emac1()) {
+		/* Enable EMAC1 clock */
+		writel(1 << ATMEL_ID_EMAC1, &pmc->pcer);
+		/* EMAC1 pins setup */
+		at91_set_b_periph(AT91_PIO_PORTC, 29, 0);	/* ETXCK */
+		at91_set_b_periph(AT91_PIO_PORTC, 28, 0);	/* ECRSDV */
+		at91_set_b_periph(AT91_PIO_PORTC, 20, 0);	/* ERXO */
+		at91_set_b_periph(AT91_PIO_PORTC, 21, 0);	/* ERX1 */
+		at91_set_b_periph(AT91_PIO_PORTC, 16, 0);	/* ERXER */
+		at91_set_b_periph(AT91_PIO_PORTC, 27, 0);	/* ETXEN */
+		at91_set_b_periph(AT91_PIO_PORTC, 18, 0);	/* ETX0 */
+		at91_set_b_periph(AT91_PIO_PORTC, 19, 0);	/* ETX1 */
+		at91_set_b_periph(AT91_PIO_PORTC, 31, 0);	/* EMDIO */
+		at91_set_b_periph(AT91_PIO_PORTC, 30, 0);	/* EMDC */
+	}
+
+#ifndef CONFIG_RMII
+	/* Only emac0 support MII */
+	if (has_emac0()) {
+		at91_set_b_periph(AT91_PIO_PORTB, 16, 0);	/* ECRS */
+		at91_set_b_periph(AT91_PIO_PORTB, 17, 0);	/* ECOL */
+		at91_set_b_periph(AT91_PIO_PORTB, 13,  0);	/* ERX2 */
+		at91_set_b_periph(AT91_PIO_PORTB, 14,  0);	/* ERX3 */
+		at91_set_b_periph(AT91_PIO_PORTB, 15, 0);	/* ERXCK */
+		at91_set_b_periph(AT91_PIO_PORTB, 11,  0);	/* ETX2 */
+		at91_set_b_periph(AT91_PIO_PORTB, 12,  0);	/* ETX3 */
+		at91_set_b_periph(AT91_PIO_PORTB, 8, 0);	/* ETXER */
+	}
+#endif
+}
+#endif

arch/arm/cpu/arm926ejs/at91/clock.c +2 -1

index a7085de..4d09542 100644
@@ -154,7 +154,8 @@ int at91_clock_init(unsigned long main_clock)
 	 * For now, assume this parentage won't change.
 	 */
 	mckr = readl(&pmc->mckr);
-#if defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45)
+#if defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45) \
+		|| defined(CONFIG_AT91SAM9X5)
 	/* plla divisor by 2 */
 	gd->plla_rate_hz /= (1 << ((mckr & 1 << 12) >> 12));
 #endif

arch/arm/cpu/arm926ejs/at91/clock.c +2 -0

+#elif defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45) \
+		|| defined(CONFIG_AT91SAM9X5)
 	gd->mck_rate_hz = (mckr & AT91_PMC_MCKR_MDIV_MASK) ==
 		(AT91_PMC_MCKR_MDIV_2 | AT91_PMC_MCKR_MDIV_4)
 		? freq / 3

arch/arm/include/asm/arch-at91/at91sam9_matrix.h +2 -0

index 6d97189..b9a93b0 100644
@@ -23,6 +23,8 @@
 #include <asm/arch/at91cap9_matrix.h>
 #elif defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45)
 #include <asm/arch/at91sam9g45_matrix.h>
+#elif defined(CONFIG_AT91SAM9X5)
+#include <asm/arch/at91sam9x5_matrix.h>
 #else
 #error "Unsupported AT91SAM9/CAP9 processor"
 #endif

arch/arm/include/asm/arch-at91/at91sam9x5.h new file +172 -0

new file mode 100644
index 0000000..30bad24
@@ -0,0 +1,172 @@
+/*
+ * Chip-specific header file for the AT91SAM9x5 family
+ *
+ *  Copyright (C) 2012 Atmel Corporation.
+ *
+ * Definitions for the SoC:
+ * AT91SAM9x5
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91SAM9X5_H
+#define AT91SAM9X5_H
+
+/*
+ * Peripheral identifiers/interrupts.
+ */
+#define ATMEL_ID_FIQ	0	/* Advanced Interrupt Controller (FIQ) */
+#define ATMEL_ID_SYS	1	/* System Controller Interrupt */
+
+#define ATMEL_ID_FIQ	0	/* Advanced Interrupt Controller (FIQ) */
+#define ATMEL_ID_SYS	1	/* System Controller Interrupt */
+#define ATMEL_ID_PIOAB	2	/* Parallel I/O Controller A and B */
+#define ATMEL_ID_PIOCD	3	/* Parallel I/O Controller C and D */
+#define ATMEL_ID_SMD	4	/* SMD Soft Modem (SMD) */
+#define ATMEL_ID_USART0	5	/* USART 0 */
+#define ATMEL_ID_USART1	6	/* USART 1 */
+#define ATMEL_ID_USART2	7	/* USART 2 */
+#define ATMEL_ID_TWI0	9	/* Two-Wire Interface 0 */
+#define ATMEL_ID_TWI1	10	/* Two-Wire Interface 1 */
+#define ATMEL_ID_TWI2	11	/* Two-Wire Interface 2 */
+#define ATMEL_ID_HSMCI0	12	/* High Speed Multimedia Card Interface 0 */
+#define ATMEL_ID_SPI0	13	/* Serial Peripheral Interface 0 */
+#define ATMEL_ID_SPI1	14	/* Serial Peripheral Interface 1 */
+#define ATMEL_ID_UART0	15	/* UART 0 */
+#define ATMEL_ID_UART1	16	/* UART 1 */
+#define ATMEL_ID_TC01	17	/* Timer Counter 0, 1, 2, 3, 4 and 5 */
+#define ATMEL_ID_PWM	18	/* Pulse Width Modulation Controller */
+#define ATMEL_ID_ADC	19	/* ADC Controller */
+#define ATMEL_ID_DMAC0	20	/* DMA Controller 0 */
+#define ATMEL_ID_DMAC1	21	/* DMA Controller 1 */
+#define ATMEL_ID_UHPHS	22	/* USB Host High Speed */
+#define ATMEL_ID_UDPHS	23	/* USB Device High Speed */
+#define ATMEL_ID_EMAC0	24	/* Ethernet MAC0 */
+#define ATMEL_ID_LCDC	25	/* LCD Controller */
+#define ATMEL_ID_HSMCI1	26	/* High Speed Multimedia Card Interface 1 */
+#define ATMEL_ID_EMAC1	27	/* Ethernet MAC1 */
+#define ATMEL_ID_SSC	28	/* Synchronous Serial Controller */
+#define ATMEL_ID_IRQ	31	/* Advanced Interrupt Controller */
+
+/*
+ * User Peripheral physical base addresses.
+ */
+#define ATMEL_BASE_SPI0		0xf0000000
+#define ATMEL_BASE_SPI1		0xf0004000
+#define ATMEL_BASE_HSMCI0	0xf0008000
+#define ATMEL_BASE_HSMCI1	0xf000c000
+#define ATMEL_BASE_SSC		0xf0010000
+#define ATMEL_BASE_CAN0		0xf8000000
+#define ATMEL_BASE_CAN1		0xf8004000
+#define ATMEL_BASE_TC0		0xf8008000
+#define ATMEL_BASE_TC1		0xf8008040
+#define ATMEL_BASE_TC2		0xf8008080
+#define ATMEL_BASE_TC3		0xf800c000
+#define ATMEL_BASE_TC4		0xf800c040
+#define ATMEL_BASE_TC5		0xf800c080
+#define ATMEL_BASE_TWI0		0xf8010000
+#define ATMEL_BASE_TWI1		0xf8014000
+#define ATMEL_BASE_TWI2		0xf8018000
+#define ATMEL_BASE_USART0	0xf801c000
+#define ATMEL_BASE_USART1	0xf8020000
+#define ATMEL_BASE_USART2	0xf8024000
+#define ATMEL_BASE_USART3	0xf8028000
+#define ATMEL_BASE_EMAC0	0xf802c000
+#define ATMEL_BASE_EMAC1	0xf8030000
+#define ATMEL_BASE_PWM		0xf8034000
+#define ATMEL_BASE_LCDC		0xf8038000
+#define ATMEL_BASE_UDPHS	0xf803c000
+#define ATMEL_BASE_UART0	0xf8040000
+#define ATMEL_BASE_UART1	0xf8044000
+#define ATMEL_BASE_ISI		0xf8048000
+#define ATMEL_BASE_ADC		0xf804c000
+#define ATMEL_BASE_SYS		0xffffc000
+
+/*
+ * System Peripherals (offset from ATMEL_BASE_SYS)
+ */
+#define ATMEL_BASE_MATRIX	0xffffde00
+#define ATMEL_BASE_PMECC	0xffffe000
+#define ATMEL_BASE_PMERRLOC	0xffffe600
+#define ATMEL_BASE_DDRSDRC	0xffffe800
+#define ATMEL_BASE_SMC		0xffffea00
+#define ATMEL_BASE_DMAC0	0xffffec00
+#define ATMEL_BASE_DMAC1	0xffffee00
+#define ATMEL_BASE_AIC		0xfffff000
+#define ATMEL_BASE_DBGU		0xfffff200
+#define ATMEL_BASE_PIOA		0xfffff400
+#define ATMEL_BASE_PIOB		0xfffff600
+#define ATMEL_BASE_PIOC		0xfffff800
+#define ATMEL_BASE_PIOD		0xfffffa00
+#define ATMEL_BASE_PMC		0xfffffc00
+#define ATMEL_BASE_RSTC		0xfffffe00
+#define ATMEL_BASE_SHDWC	0xfffffe10
+#define ATMEL_BASE_PIT		0xfffffe30
+#define ATMEL_BASE_WDT		0xfffffe40
+#define ATMEL_BASE_GPBR		0xfffffe60
+#define ATMEL_BASE_RTC		0xfffffeb0
+
+/*
+ * Internal Memory.
+ */
+#define ATMEL_BASE_ROM		0x00100000 /* Internal ROM base address */
+#define ATMEL_BASE_SRAM		0x00300000 /* Internal SRAM base address */
+#define ATMEL_BASE_SMD		0x00400000 /* SMD Controller */
+#define ATMEL_BASE_UDPHS_FIFO	0x00500000 /* USB Device HS controller */
+#define ATMEL_BASE_OHCI		0x00600000 /* USB Host controller (OHCI) */
+#define ATMEL_BASE_EHCI		0x00700000 /* USB Host controller (EHCI) */
+
+/* 9x5 series chip id definitions */
+#define ARCH_ID_AT91SAM9X5	0x819a05a0
+#define ARCH_EXID_AT91SAM9G15	0x00000000
+#define ARCH_EXID_AT91SAM9G35	0x00000001
+#define ARCH_EXID_AT91SAM9X35	0x00000002
+#define ARCH_EXID_AT91SAM9G25	0x00000003
+#define ARCH_EXID_AT91SAM9X25	0x00000004
+
+#define cpu_is_at91sam9x5()	(get_chip_id() == ARCH_ID_AT91SAM9X5)
+#define cpu_is_at91sam9g15()	(cpu_is_at91sam9x5() && \
+			(get_extension_chip_id() == ARCH_EXID_AT91SAM9G15))
+#define cpu_is_at91sam9g25()	(cpu_is_at91sam9x5() && \
+			(get_extension_chip_id() == ARCH_EXID_AT91SAM9G25))
+#define cpu_is_at91sam9g35()	(cpu_is_at91sam9x5() && \
+			(get_extension_chip_id() == ARCH_EXID_AT91SAM9G35))
+#define cpu_is_at91sam9x25()	(cpu_is_at91sam9x5() && \
+			(get_extension_chip_id() == ARCH_EXID_AT91SAM9X25))
+#define cpu_is_at91sam9x35()	(cpu_is_at91sam9x5() && \
+			(get_extension_chip_id() == ARCH_EXID_AT91SAM9X35))
+
+/*
+ * Cpu Name
+ */
+#define CONFIG_SYS_AT91_G15_CPU_NAME	"AT91SAM9G15"
+#define CONFIG_SYS_AT91_G25_CPU_NAME	"AT91SAM9G25"
+#define CONFIG_SYS_AT91_G35_CPU_NAME	"AT91SAM9G35"
+#define CONFIG_SYS_AT91_X25_CPU_NAME	"AT91SAM9X25"
+#define CONFIG_SYS_AT91_X35_CPU_NAME	"AT91SAM9X35"
+#define CONFIG_SYS_AT91_UNKNOWN_CPU	"Unknown CPU type"
+#define ATMEL_CPU_NAME	get_cpu_name()
+
+/*
+ * Other misc defines
+ */
+#define ATMEL_PIO_PORTS         5
+#define CPU_HAS_PIO3
+#define PIO_SCDR_DIV            (0x3fff <<  0)  /* Slow Clock Divider Mask */
+
+/*
+ * at91sam9x5 specific prototypes
+ */
+#ifndef __ASSEMBLY__
+unsigned int get_chip_id(void);
+unsigned int get_extension_chip_id(void);
+unsigned int has_emac1(void);
+unsigned int has_emac0(void);
+unsigned int has_lcdc(void);
+char *get_cpu_name(void);
+#endif
+
+#endif

arch/arm/include/asm/arch-at91/at91sam9x5_matrix.h new file +0 -0

new file mode 100644
index 0000000..cbc350c

arch/arm/include/asm/arch-at91/at91sam9x5_matrix.h new file +84 -0

+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91SAM9G45_MATRIX_H
+#define AT91SAM9G45_MATRIX_H
+
+#ifndef __ASSEMBLY__
+
+struct at91_matrix {
+	u32	mcfg[16];
+	u32	scfg[16];
+	u32	pras[16][2];
+	u32	mrcr;           /* 0x100 Master Remap Control */
+	u32	filler[7];
+	u32	ebicsa;
+	u32	filler4[47];
+	u32	wpmr;
+	u32	wpsr;
+};
+
+#endif /* __ASSEMBLY__ */
+
+#define AT91_MATRIX_ULBT_INFINITE	(0 << 0)
+#define AT91_MATRIX_ULBT_SINGLE		(1 << 0)
+#define AT91_MATRIX_ULBT_FOUR		(2 << 0)
+#define AT91_MATRIX_ULBT_EIGHT		(3 << 0)
+#define AT91_MATRIX_ULBT_SIXTEEN	(4 << 0)
+#define AT91_MATRIX_ULBT_THIRTYTWO	(5 << 0)
+#define AT91_MATRIX_ULBT_SIXTYFOUR	(6 << 0)
+#define AT91_MATRIX_ULBT_128		(7 << 0)
+
+#define AT91_MATRIX_DEFMSTR_TYPE_NONE	(0 << 16)
+#define AT91_MATRIX_DEFMSTR_TYPE_LAST	(1 << 16)
+#define AT91_MATRIX_DEFMSTR_TYPE_FIXED	(2 << 16)
+#define AT91_MATRIX_FIXED_DEFMSTR_SHIFT 18
+
+#define AT91_MATRIX_M0PR_SHIFT          0
+#define AT91_MATRIX_M1PR_SHIFT          4
+#define AT91_MATRIX_M2PR_SHIFT          8
+#define AT91_MATRIX_M3PR_SHIFT          12
+#define AT91_MATRIX_M4PR_SHIFT          16
+#define AT91_MATRIX_M5PR_SHIFT          20
+#define AT91_MATRIX_M6PR_SHIFT          24
+#define AT91_MATRIX_M7PR_SHIFT          28
+
+#define AT91_MATRIX_M8PR_SHIFT          0  /* register B */
+#define AT91_MATRIX_M9PR_SHIFT          4  /* register B */
+#define AT91_MATRIX_M10PR_SHIFT         8  /* register B */
+#define AT91_MATRIX_M11PR_SHIFT         12 /* register B */
+
+#define AT91_MATRIX_RCB0                (1 << 0)
+#define AT91_MATRIX_RCB1                (1 << 1)
+#define AT91_MATRIX_RCB2                (1 << 2)
+#define AT91_MATRIX_RCB3                (1 << 3)
+#define AT91_MATRIX_RCB4                (1 << 4)
+#define AT91_MATRIX_RCB5                (1 << 5)
+#define AT91_MATRIX_RCB6                (1 << 6)
+#define AT91_MATRIX_RCB7                (1 << 7)
+#define AT91_MATRIX_RCB8                (1 << 8)
+#define AT91_MATRIX_RCB9                (1 << 9)
+#define AT91_MATRIX_RCB10               (1 << 10)
+
+#define AT91_MATRIX_EBI_CS1A_SMC                (0 << 1)
+#define AT91_MATRIX_EBI_CS1A_SDRAMC             (1 << 1)
+#define AT91_MATRIX_EBI_CS3A_SMC                (0 << 3)
+#define AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA     (1 << 3)
+#define AT91_MATRIX_EBI_DBPU_ON                 (0 << 8)
+#define AT91_MATRIX_EBI_DBPU_OFF                (1 << 8)
+#define AT91_MATRIX_EBI_DBPD_ON                 (0 << 9)
+#define AT91_MATRIX_EBI_DBPD_OFF                (1 << 9)
+#define AT91_MATRIX_EBI_VDDIOMSEL_1_8V          (0 << 16)
+#define AT91_MATRIX_EBI_VDDIOMSEL_3_3V          (1 << 16)
+#define AT91_MATRIX_EBI_EBI_IOSR_REDUCED        (0 << 17)
+#define AT91_MATRIX_EBI_EBI_IOSR_NORMAL         (1 << 17)
+#define AT91_MATRIX_NFD0_ON_D0                  (0 << 24)
+#define AT91_MATRIX_NFD0_ON_D16                 (1 << 24)
+#define AT91_MATRIX_MP_OFF                      (0 << 25)
+#define AT91_MATRIX_MP_ON                       (1 << 25)
+
+#endif

arch/arm/include/asm/arch-at91/hardware.h +2 -0

index 85c2889..4c4ee70 100644
@@ -37,6 +37,8 @@
 # include <asm/arch/at91sam9rl.h>
 #elif defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45)
 # include <asm/arch/at91sam9g45.h>
+#elif defined(CONFIG_AT91SAM9X5)
+# include <asm/arch/at91sam9x5.h>
 #elif defined(CONFIG_AT91CAP9)
 # include <asm/arch/at91cap9.h>
 #elif defined(CONFIG_AT91X40)

board/atmel/at91sam9x5ek/Makefile new file +0 -0

new file mode 100644
index 0000000..1c9a4b6

board/atmel/at91sam9x5ek/Makefile new file +41 -0

+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS-y += at91sam9x5ek.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################

board/atmel/at91sam9x5ek/at91sam9x5ek.c new file +100 -0

new file mode 100644
index 0000000..ff8c518
@@ -0,0 +1,306 @@
+/*
+ * Copyright (C) 2012 Atmel Corporation
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/at91sam9x5_matrix.h>
+#include <asm/arch/at91sam9_smc.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/clk.h>
+#include <lcd.h>
+#include <atmel_hlcdc.h>
+#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
+#include <net.h>
+#endif
+#include <netdev.h>
+#ifdef CONFIG_LCD_INFO
+#include <nand.h>
+#include <version.h>
+#endif
+#ifdef CONFIG_ATMEL_SPI
+#include <spi.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* ------------------------------------------------------------------------- */
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+#ifdef CONFIG_CMD_NAND
+static void at91sam9x5ek_nand_hw_init(void)
+{
+	struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
+	struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+	unsigned long csa;
+
+	/* Enable CS3 */
+	csa = readl(&matrix->ebicsa);
+	csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA;
+	writel(csa, &matrix->ebicsa);
+
+	/* Configure SMC CS3 for NAND/SmartMedia */
+	writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
+		AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
+		&smc->cs[3].setup);
+	writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(4) |
+		AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(4),
+		&smc->cs[3].pulse);
+	writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7),
+		&smc->cs[3].cycle);
+	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+		AT91_SMC_MODE_EXNW_DISABLE |
+#ifdef CONFIG_SYS_NAND_DBW_16
+		AT91_SMC_MODE_DBW_16 |
+#else /* CONFIG_SYS_NAND_DBW_8 */
+		AT91_SMC_MODE_DBW_8 |
+#endif
+		AT91_SMC_MODE_TDF_CYCLE(3),
+		&smc->cs[3].mode);
+
+	writel(1 << ATMEL_ID_PIOCD, &pmc->pcer);
+
+	/* Configure RDY/BSY */
+	at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
+	/* Enable NandFlash */
+	at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
+
+	at91_set_a_periph(AT91_PIO_PORTD, 0, 1);	/* NAND OE */
+	at91_set_a_periph(AT91_PIO_PORTD, 1, 1);	/* NAND WE */
+	at91_set_a_periph(AT91_PIO_PORTD, 2, 1);	/* NAND ALE */
+	at91_set_a_periph(AT91_PIO_PORTD, 3, 1);	/* NAND CLE */
+	at91_set_a_periph(AT91_PIO_PORTD, 6, 1);
+	at91_set_a_periph(AT91_PIO_PORTD, 7, 1);
+	at91_set_a_periph(AT91_PIO_PORTD, 8, 1);
+	at91_set_a_periph(AT91_PIO_PORTD, 9, 1);
+	at91_set_a_periph(AT91_PIO_PORTD, 10, 1);
+	at91_set_a_periph(AT91_PIO_PORTD, 11, 1);

board/atmel/at91sam9x5ek/at91sam9x5ek.c new file +12 -0

+
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+
+#ifdef CONFIG_MACB
+	if (has_emac0())
+		rc = macb_eth_initialize(0,
+			(void *)ATMEL_BASE_EMAC0, 0x00);
+	if (has_emac1())
+		rc = macb_eth_initialize(1,
+			(void *)ATMEL_BASE_EMAC1, 0x00);

board/atmel/at91sam9x5ek/at91sam9x5ek.c new file +150 -0

+
+#ifdef CONFIG_LCD
+vidinfo_t panel_info = {
+	.vl_col	= 800,
+	.vl_row = 480,
+	.vl_clk = 24000000,
+	.vl_sync = LCDC_LCDCFG5_HSPOL | LCDC_LCDCFG5_VSPOL,
+	.vl_bpix = LCD_BPP,
+	.vl_tft = 1,
+	.vl_clk_pol = 1,
+	.vl_hsync_len = 128,
+	.vl_left_margin = 64,
+	.vl_right_margin = 64,
+	.vl_vsync_len = 2,
+	.vl_upper_margin = 22,
+	.vl_lower_margin = 21,
+	.mmio = ATMEL_BASE_LCDC,
+};
+
+void lcd_enable(void)
+{
+	if (has_lcdc())
+		at91_set_a_periph(AT91_PIO_PORTC, 29, 1);	/* power up */
+}
+
+void lcd_disable(void)
+{
+	if (has_lcdc())
+		at91_set_a_periph(AT91_PIO_PORTC, 29, 0);	/* power down */
+}
+
+static void at91sam9x5ek_lcd_hw_init(void)
+{
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
+	if (has_lcdc()) {
+		at91_set_a_periph(AT91_PIO_PORTC, 26, 0);	/* LCDPWM */
+		at91_set_a_periph(AT91_PIO_PORTC, 27, 0);	/* LCDVSYNC */
+		at91_set_a_periph(AT91_PIO_PORTC, 28, 0);	/* LCDHSYNC */
+		at91_set_a_periph(AT91_PIO_PORTC, 24, 0);	/* LCDDISP */
+		at91_set_a_periph(AT91_PIO_PORTC, 29, 0);	/* LCDDEN */
+		at91_set_a_periph(AT91_PIO_PORTC, 30, 0);	/* LCDPCK */
+
+		at91_set_a_periph(AT91_PIO_PORTC, 0, 0);	/* LCDD0 */
+		at91_set_a_periph(AT91_PIO_PORTC, 1, 0);	/* LCDD1 */
+		at91_set_a_periph(AT91_PIO_PORTC, 2, 0);	/* LCDD2 */
+		at91_set_a_periph(AT91_PIO_PORTC, 3, 0);	/* LCDD3 */
+		at91_set_a_periph(AT91_PIO_PORTC, 4, 0);	/* LCDD4 */
+		at91_set_a_periph(AT91_PIO_PORTC, 5, 0);	/* LCDD5 */
+		at91_set_a_periph(AT91_PIO_PORTC, 6, 0);	/* LCDD6 */
+		at91_set_a_periph(AT91_PIO_PORTC, 7, 0);	/* LCDD7 */
+		at91_set_a_periph(AT91_PIO_PORTC, 8, 0);	/* LCDD8 */
+		at91_set_a_periph(AT91_PIO_PORTC, 9, 0);	/* LCDD9 */
+		at91_set_a_periph(AT91_PIO_PORTC, 10, 0);	/* LCDD10 */
+		at91_set_a_periph(AT91_PIO_PORTC, 11, 0);	/* LCDD11 */
+		at91_set_a_periph(AT91_PIO_PORTC, 12, 0);	/* LCDD12 */
+		at91_set_a_periph(AT91_PIO_PORTC, 13, 0);	/* LCDD13 */
+		at91_set_a_periph(AT91_PIO_PORTC, 14, 0);	/* LCDD14 */
+		at91_set_a_periph(AT91_PIO_PORTC, 15, 0);	/* LCDD15 */
+		at91_set_a_periph(AT91_PIO_PORTC, 16, 0);	/* LCDD16 */
+		at91_set_a_periph(AT91_PIO_PORTC, 17, 0);	/* LCDD17 */
+		at91_set_a_periph(AT91_PIO_PORTC, 18, 0);	/* LCDD18 */
+		at91_set_a_periph(AT91_PIO_PORTC, 19, 0);	/* LCDD19 */
+		at91_set_a_periph(AT91_PIO_PORTC, 20, 0);	/* LCDD20 */
+		at91_set_a_periph(AT91_PIO_PORTC, 21, 0);	/* LCDD21 */
+		at91_set_a_periph(AT91_PIO_PORTC, 22, 0);	/* LCDD22 */
+		at91_set_a_periph(AT91_PIO_PORTC, 23, 0);	/* LCDD23 */
+
+		writel(1 << ATMEL_ID_LCDC, &pmc->pcer);
+	}
+}
+
+#ifdef CONFIG_LCD_INFO
+void lcd_show_board_info(void)
+{
+	ulong dram_size, nand_size;
+	int i;
+	char temp[32];
+
+	if (has_lcdc()) {
+		lcd_printf("%s\n", U_BOOT_VERSION);
+		lcd_printf("(C) 2012 ATMEL Corp\n");
+		lcd_printf("at91support at atmel.com\n");
+		lcd_printf("%s CPU at %s MHz\n",
+			get_cpu_name(),
+			strmhz(temp, get_cpu_clk_rate()));
+
+		dram_size = 0;
+		for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
+			dram_size += gd->bd->bi_dram[i].size;
+		nand_size = 0;
+		for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
+			nand_size += nand_info[i].size;
+		lcd_printf("  %ld MB SDRAM, %ld MB NAND\n",
+			dram_size >> 20,
+			nand_size >> 20);
+	}
+}
+#endif /* CONFIG_LCD_INFO */
+#endif /* CONFIG_LCD */
+
+/* SPI chip select control */
+#ifdef CONFIG_ATMEL_SPI
+int spi_cs_is_valid(unsigned int bus, unsigned int cs)
+{
+	return bus == 0 && cs < 2;
+}
+
+void spi_cs_activate(struct spi_slave *slave)
+{
+	switch (slave->cs) {
+	case 1:
+		at91_set_gpio_output(AT91_PIN_PA7, 0);
+		break;
+	case 0:
+	default:
+		at91_set_gpio_output(AT91_PIN_PA14, 0);
+		break;
+	}
+}
+
+void spi_cs_deactivate(struct spi_slave *slave)
+{
+	switch (slave->cs) {
+	case 1:
+		at91_set_gpio_output(AT91_PIN_PA7, 1);
+		break;
+	case 0:
+	default:
+		at91_set_gpio_output(AT91_PIN_PA14, 1);
+		break;
+	}
+}
+#endif /* CONFIG_ATMEL_SPI */
+
+int board_early_init_f(void)
+{
+	at91_seriald_hw_init();
+	return 0;
+}
+
+int board_init(void)
+{
+	/* arch number of ATMELEK-Board */
+	gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9X5EK;
+
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+#ifdef CONFIG_CMD_NAND

board/atmel/at91sam9x5ek/at91sam9x5ek.c new file +14 -0

+#endif
+
+#ifdef CONFIG_LCD
+	at91sam9x5ek_lcd_hw_init();
+#endif
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *) CONFIG_SYS_SDRAM_BASE,
+					CONFIG_SYS_SDRAM_SIZE);
+	return 0;
+}

board/atmel/at91sam9x5ek/config.mk new file +1 -0

new file mode 100644
index 0000000..6589a12
@@ -0,0 +1 @@
+CONFIG_SYS_TEXT_BASE = 0x26f00000

boards.cfg +1 -0

index 9205070..c9bd1b3 100644
@@ -89,6 +89,7 @@ at91sam9g20ek_nandflash      arm         arm926ejs   at91sam9260ek       atmel
 at91sam9m10g45ek_nandflash   arm         arm926ejs   at91sam9m10g45ek    atmel          at91        at91sam9m10g45ek:AT91SAM9M10G45,SYS_USE_NANDFLASH
 at91sam9rlek_dataflash       arm         arm926ejs   at91sam9rlek        atmel          at91        at91sam9rlek:AT91SAM9RL,SYS_USE_DATAFLASH
 at91sam9rlek_nandflash       arm         arm926ejs   at91sam9rlek        atmel          at91        at91sam9rlek:AT91SAM9RL,SYS_USE_NANDFLASH
+at91sam9x5ek_nandflash       arm         arm926ejs   at91sam9x5ek        atmel          at91        at91sam9x5ek:AT91SAM9X5,SYS_USE_NANDFLASH
 at91sam9xeek_dataflash_cs0   arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9XE,SYS_USE_DATAFLASH_CS0
 at91sam9xeek_dataflash_cs1   arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9XE,SYS_USE_DATAFLASH_CS1
 at91sam9xeek_nandflash       arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9XE,SYS_USE_NANDFLASH

drivers/net/macb.c +2 -2

index 4578467..8f55cdc 100644
@@ -471,7 +471,7 @@ static int macb_init(struct eth_device *netdev, bd_t *bd)
 #if	defined(CONFIG_AT91CAP9) || defined(CONFIG_AT91SAM9260) || \
 	defined(CONFIG_AT91SAM9263) || defined(CONFIG_AT91SAM9G20) || \
 	defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45) || \
-	defined(CONFIG_AT91SAM9XE)
+	defined(CONFIG_AT91SAM9XE) || defined(CONFIG_AT91SAM9X5)
 	macb_writel(macb, USRIO, MACB_BIT(RMII) | MACB_BIT(CLKEN));
 #else
 	macb_writel(macb, USRIO, 0);

@@ -480,7 +480,7 @@ static int macb_init(struct eth_device *netdev, bd_t *bd)
 #if	defined(CONFIG_AT91CAP9) || defined(CONFIG_AT91SAM9260) || \
 	defined(CONFIG_AT91SAM9263) || defined(CONFIG_AT91SAM9G20) || \
 	defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45) || \
-	defined(CONFIG_AT91SAM9XE)
+	defined(CONFIG_AT91SAM9XE) || defined(CONFIG_AT91SAM9X5)
 	macb_writel(macb, USRIO, MACB_BIT(CLKEN));
 #else
 	macb_writel(macb, USRIO, MACB_BIT(MII));

drivers/serial/atmel_usart.h +0 -0

index 7e4b2c9..ad1d9f0 100644

drivers/serial/atmel_usart.h +0 -0

 /* Bit manipulation macros */
 #define USART3_BIT(name)				\
 	(1 << USART3_##name##_OFFSET)

include/configs/at91sam9x5ek.h new file +29 -0

new file mode 100644
index 0000000..9aba52c
@@ -0,0 +1,201 @@
+/*
+ * Copyright (C) 2012 Atmel Corporation
+ *
+ * Configuation settings for the AT91SAM9X5EK board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H__
+#define __CONFIG_H__
+
+#include <asm/hardware.h>
+

include/configs/at91sam9x5ek.h new file +35 -0

+
+#define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_DISPLAY_CPUINFO
+
+/* general purpose I/O */
+#define CONFIG_ATMEL_LEGACY		/* required until (g)pio is fixed */
+#define CONFIG_AT91_GPIO
+
+/* serial console */
+#define CONFIG_ATMEL_USART
+#define CONFIG_USART_BASE	ATMEL_BASE_DBGU
+#define CONFIG_USART_ID		ATMEL_ID_SYS
+
+/* LCD */
+#define CONFIG_LCD
+#define LCD_BPP			LCD_COLOR16
+#define LCD_OUTPUT_BPP		24
+#define CONFIG_LCD_LOGO
+#undef LCD_TEST_PATTERN
+#define CONFIG_LCD_INFO
+#define CONFIG_LCD_INFO_BELOW_LOGO
+#define CONFIG_SYS_WHITE_ON_BLACK
+#define CONFIG_ATMEL_HLCD
+#define CONFIG_ATMEL_LCD_RGB565
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+
+#define CONFIG_BOOTDELAY	3
+
+/*
+ * BOOTP options
+ */

include/configs/at91sam9x5ek.h new file +42 -0

+#undef CONFIG_CMD_LOADS
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NAND
+
+/* SDRAM */
+#define CONFIG_NR_DRAM_BANKS		1
+#define CONFIG_SYS_SDRAM_BASE		0x20000000
+#define CONFIG_SYS_SDRAM_SIZE		0x08000000	/* 128 megs */
+
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
+
+/* DataFlash */
+#ifdef CONFIG_ATMEL_SPI
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_ATMEL
+#define CONFIG_SYS_MAX_DATAFLASH_BANKS
+#endif
+
+/* no NOR flash */
+#define CONFIG_SYS_NO_FLASH
+
+/* NAND flash */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_ATMEL
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		0x40000000
+#define CONFIG_SYS_NAND_DBW_8		1
+/* our ALE is AD21 */
+#define CONFIG_SYS_NAND_MASK_ALE	(1 << 21)
+/* our CLE is AD22 */
+#define CONFIG_SYS_NAND_MASK_CLE	(1 << 22)
+#define CONFIG_SYS_NAND_ENABLE_PIN	AT91_PIN_PD4
+#define CONFIG_SYS_NAND_READY_PIN	AT91_PIN_PD5
+
+#define CONFIG_MTD_DEVICE
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_PARTITIONS

include/configs/at91sam9x5ek.h new file +11 -0

+
+/* bootstrap + u-boot + env + linux in dataflash on CS0 */
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SYS_MONITOR_BASE	(0x10000000 + 0x8400)
+#define CONFIG_ENV_OFFSET	0x5000
+#define CONFIG_ENV_ADDR		(0x10000000 + CONFIG_ENV_OFFSET)
+#define CONFIG_ENV_SIZE		0x3000
+#define CONFIG_ENV_SECT_SIZE	0x1000
+#define CONFIG_BOOTCOMMAND	"sf probe 0; " \
+				"sf read 0x22000000 0x42000 0x300000; " \
+				"bootm 0x22000000"

include/configs/at91sam9x5ek.h new file +20 -0

+#endif
+
+#define CONFIG_BOOTARGS		"mem=128M console=ttyS0,115200 " \
+				"mtdparts=atmel_nand:" \
+				"8M(bootstrap/uboot/kernel)ro,-(rootfs) " \
+				"root=/dev/mtdblock1 rw " \
+				"rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs"
+
+#define CONFIG_BAUDRATE		115200
+
+#define CONFIG_SYS_PROMPT	"U-Boot> "
+#define CONFIG_SYS_CBSIZE	256
+#define CONFIG_SYS_MAXARGS	16
+#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) \
+					+ 16)
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_HUSH_PARSER
+

Dear Bo Shen,

Quoted 3 lines · Bo Shen

Add at91sam9x5ek board support, this board support the following SoCs
AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35

Quoted 4 lines

Using at91sam9x5ek_nandflash to configure for the board Now only supports NAND with software ECC boot up

This patch is based on git://git.denx.de/u-boot-atmel.git

Please place this in comment section (after '---').

Quoted 93 lines

Signed-off-by Bo Shen <[email protected]>

---
Changed since v1
Modify the code according to Andreas's suggestion

---
  MAINTAINERS                                        |    3 +
  arch/arm/cpu/arm926ejs/at91/Makefile               |    1 +
  arch/arm/cpu/arm926ejs/at91/at91sam9x5_devices.c   |  237 +++++++++++++++
  arch/arm/cpu/arm926ejs/at91/clock.c                |    7 +-
  arch/arm/include/asm/arch-at91/at91sam9_matrix.h   |    2 +
  arch/arm/include/asm/arch-at91/at91sam9x5.h        |  172 +++++++++++
  arch/arm/include/asm/arch-at91/at91sam9x5_matrix.h |   91 ++++++
  arch/arm/include/asm/arch-at91/hardware.h          |    2 +
  board/atmel/at91sam9x5ek/Makefile                  |   48 +++
  board/atmel/at91sam9x5ek/at91sam9x5ek.c            |  306 ++++++++++++++++++++
  board/atmel/at91sam9x5ek/config.mk                 |    1 +
  boards.cfg                                         |    1 +
  drivers/net/macb.c                                 |    4 +-
  drivers/serial/atmel_usart.h                       |    7 +-
  include/configs/at91sam9x5ek.h                     |  201 +++++++++++++
  15 files changed, 1077 insertions(+), 6 deletions(-)

create mode 100644 arch/arm/cpu/arm926ejs/at91/at91sam9x5_devices.c create mode 100644 arch/arm/include/asm/arch-at91/at91sam9x5.h create mode 100644 arch/arm/include/asm/arch-at91/at91sam9x5_matrix.h create mode 100644 board/atmel/at91sam9x5ek/Makefile create mode 100644 board/atmel/at91sam9x5ek/at91sam9x5ek.c create mode 100644 board/atmel/at91sam9x5ek/config.mk create mode 100644 include/configs/at91sam9x5ek.h

MAINTAINERS +3 -0

index 6438e1c..a2fccbf 100644
@@ -660,6 +660,9 @@ Sedji Gaouaou<[email protected]>
  	at91sam9g10ek		ARM926EJS (AT91SAM9G10 SoC)
  	at91sam9m10g45ek	ARM926EJS (AT91SAM9G45 SoC)
 
+Bo Shen <[email protected]>
+	at91sam9x5ek		ARM926EJS (AT91SAM9G15,G25,G35,X25,X35 SoC)
+
  Simon Guinot <[email protected]>
 
  	inetspace_v2	ARM926EJS (Kirkwood SoC)

arch/arm/cpu/arm926ejs/at91/Makefile +1 -0

index f333753..346e58f 100644
@@ -35,6 +35,7 @@ COBJS-$(CONFIG_AT91SAM9263)	+= at91sam9263_devices.o
  COBJS-$(CONFIG_AT91SAM9RL)	+= at91sam9rl_devices.o
  COBJS-$(CONFIG_AT91SAM9M10G45)	+= at91sam9m10g45_devices.o
  COBJS-$(CONFIG_AT91SAM9G45)	+= at91sam9m10g45_devices.o
+COBJS-$(CONFIG_AT91SAM9X5)	+= at91sam9x5_devices.o
  COBJS-$(CONFIG_AT91_EFLASH)	+= eflash.o
  COBJS-$(CONFIG_AT91_LED)	+= led.o
  COBJS-y += clock.o

arch/arm/cpu/arm926ejs/at91/at91sam9x5_devices.c new file +30 -0

new file mode 100644
index 0000000..2c99a4e
@@ -0,0 +1,237 @@
+/*
+ * Copyright (C) 2012 Atmel Corporation
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/gpio.h>
+#include <asm/io.h>
+#include <../drivers/serial/atmel_usart.h>
+
+unsigned int get_chip_id(void)

arch/arm/cpu/arm926ejs/at91/at91sam9x5_devices.c line 40

Quoted 10 lines

arch/arm/cpu/arm926ejs/at91/at91sam9x5_devices.c new file +10 -0

+{
+	atmel_usart3_t *dbgu = (atmel_usart3_t *)ATMEL_BASE_DBGU;
+
+	/* cidr is the same location with fidi */
+	return readl(&dbgu->fidi) & ~AT91_CIDR_VERSION;
+}
+
+unsigned int get_extension_chip_id(void)
+{
+	atmel_usart3_t *dbgu = (struct atmel_usart3_t *)ATMEL_BASE_DBGU;

please use always the struct or leave it always, but not mixing the styles.

arch/arm/cpu/arm926ejs/at91/at91sam9x5_devices.c line 44

Quoted 4 lines

arch/arm/cpu/arm926ejs/at91/at91sam9x5_devices.c new file +4 -0

+
+	/* ner is the same location with fidi */
+	return readl(&dbgu->ner);
+}

NAK, I count this worse than before.
a) including relative path
b) cidr == fidi && ner == fidi ??; how about exid?
c) struct atmel_usart3_t has same footprint in view of USART, but using that struct in this use case is wrong. If you fear to add some specific struct atmel_dbgu to arch specific includes please revert to first version with comment about the magic numbers.

Quoted 1 line

arch/arm/cpu/arm926ejs/at91/at91sam9x5_devices.c new file +1 -0

+

Quoted 14 lines

arch/arm/cpu/arm926ejs/at91/clock.c +2 -1

index a7085de..4d09542 100644
@@ -154,7 +154,8 @@ int at91_clock_init(unsigned long main_clock)
  	 * For now, assume this parentage won't change.
  	 */
  	mckr = readl(&pmc->mckr);
-#if defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45)
+#if defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45) \
+		|| defined(CONFIG_AT91SAM9X5)
  	/* plla divisor by 2 */
  	gd->plla_rate_hz /= (1 << ((mckr & 1 << 12) >> 12));
  #endif

arch/arm/cpu/arm926ejs/at91/clock.c int at91_clock_init(unsigned long main_clock) · line 172

Quoted 6 lines

arch/arm/cpu/arm926ejs/at91/clock.c +1 -1

@@ -168,7 +169,9 @@ int at91_clock_init(unsigned long main_clock)
  		freq / ((mckr & AT91_PMC_MCKR_MDIV_MASK) >> 7) : freq;
  	if (mckr & AT91_PMC_MCKR_MDIV_MASK)
  		freq /= 2;			/* processor clock division */
-#elif defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45)
+	/* mck divisor by 2 */

I think this is also wrong here, it may be mck/2 or mck/4 or am I wrong?

Quoted 6 lines

arch/arm/cpu/arm926ejs/at91/clock.c +2 -0

+#elif defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45) \
+		|| defined(CONFIG_AT91SAM9X5)
  	gd->mck_rate_hz = (mckr & AT91_PMC_MCKR_MDIV_MASK) ==
  		(AT91_PMC_MCKR_MDIV_2 | AT91_PMC_MCKR_MDIV_4)
  		? freq / 3

Quoted 4 lines

arch/arm/include/asm/arch-at91/at91sam9x5_matrix.h new file +0 -1

new file mode 100644
index 0000000..cbc350c
--- /dev/null

arch/arm/include/asm/arch-at91/at91sam9x5_matrix.h line 4

Quoted 6 lines

+++ b/arch/arm/include/asm/arch-at91/at91sam9x5_matrix.h

arch/arm/include/asm/arch-at91/at91sam9x5_matrix.h new file +4 -0

@@ -0,0 +1,91 @@
+/*
+ * Matrix-centric header file for the AT91SAM9M1x family
+ *
+ *  Copyright (C) 2008 Atmel Corporation.

I guess you should adopt the copyright

arch/arm/include/asm/arch-at91/at91sam9x5_matrix.h line 7

Quoted 4 lines

arch/arm/include/asm/arch-at91/at91sam9x5_matrix.h new file +3 -0

+ *
+ * Memory Controllers (MATRIX, EBI) - System peripherals registers.
+ * Based on AT91SAM9G45 preliminary datasheet.

Ouch, that slipped through in last review. This is copied from at91sam9g45_matrix.h.

If at91sam9x5 matches at91sam9g45 why another include? If not please change the source of information (and include guards some lines down).

Quoted 105 lines

arch/arm/include/asm/arch-at91/at91sam9x5_matrix.h new file +84 -0

+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91SAM9G45_MATRIX_H
+#define AT91SAM9G45_MATRIX_H
+
+#ifndef __ASSEMBLY__
+
+struct at91_matrix {
+	u32	mcfg[16];
+	u32	scfg[16];
+	u32	pras[16][2];
+	u32	mrcr;           /* 0x100 Master Remap Control */
+	u32	filler[7];
+	u32	ebicsa;
+	u32	filler4[47];
+	u32	wpmr;
+	u32	wpsr;
+};
+
+#endif /* __ASSEMBLY__ */
+
+#define AT91_MATRIX_ULBT_INFINITE	(0 << 0)
+#define AT91_MATRIX_ULBT_SINGLE		(1 << 0)
+#define AT91_MATRIX_ULBT_FOUR		(2 << 0)
+#define AT91_MATRIX_ULBT_EIGHT		(3 << 0)
+#define AT91_MATRIX_ULBT_SIXTEEN	(4 << 0)
+#define AT91_MATRIX_ULBT_THIRTYTWO	(5 << 0)
+#define AT91_MATRIX_ULBT_SIXTYFOUR	(6 << 0)
+#define AT91_MATRIX_ULBT_128		(7 << 0)
+
+#define AT91_MATRIX_DEFMSTR_TYPE_NONE	(0 << 16)
+#define AT91_MATRIX_DEFMSTR_TYPE_LAST	(1 << 16)
+#define AT91_MATRIX_DEFMSTR_TYPE_FIXED	(2 << 16)
+#define AT91_MATRIX_FIXED_DEFMSTR_SHIFT 18
+
+#define AT91_MATRIX_M0PR_SHIFT          0
+#define AT91_MATRIX_M1PR_SHIFT          4
+#define AT91_MATRIX_M2PR_SHIFT          8
+#define AT91_MATRIX_M3PR_SHIFT          12
+#define AT91_MATRIX_M4PR_SHIFT          16
+#define AT91_MATRIX_M5PR_SHIFT          20
+#define AT91_MATRIX_M6PR_SHIFT          24
+#define AT91_MATRIX_M7PR_SHIFT          28
+
+#define AT91_MATRIX_M8PR_SHIFT          0  /* register B */
+#define AT91_MATRIX_M9PR_SHIFT          4  /* register B */
+#define AT91_MATRIX_M10PR_SHIFT         8  /* register B */
+#define AT91_MATRIX_M11PR_SHIFT         12 /* register B */
+
+#define AT91_MATRIX_RCB0                (1 << 0)
+#define AT91_MATRIX_RCB1                (1 << 1)
+#define AT91_MATRIX_RCB2                (1 << 2)
+#define AT91_MATRIX_RCB3                (1 << 3)
+#define AT91_MATRIX_RCB4                (1 << 4)
+#define AT91_MATRIX_RCB5                (1 << 5)
+#define AT91_MATRIX_RCB6                (1 << 6)
+#define AT91_MATRIX_RCB7                (1 << 7)
+#define AT91_MATRIX_RCB8                (1 << 8)
+#define AT91_MATRIX_RCB9                (1 << 9)
+#define AT91_MATRIX_RCB10               (1 << 10)
+
+#define AT91_MATRIX_EBI_CS1A_SMC                (0 << 1)
+#define AT91_MATRIX_EBI_CS1A_SDRAMC             (1 << 1)
+#define AT91_MATRIX_EBI_CS3A_SMC                (0 << 3)
+#define AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA     (1 << 3)
+#define AT91_MATRIX_EBI_DBPU_ON                 (0 << 8)
+#define AT91_MATRIX_EBI_DBPU_OFF                (1 << 8)
+#define AT91_MATRIX_EBI_DBPD_ON                 (0 << 9)
+#define AT91_MATRIX_EBI_DBPD_OFF                (1 << 9)
+#define AT91_MATRIX_EBI_VDDIOMSEL_1_8V          (0 << 16)
+#define AT91_MATRIX_EBI_VDDIOMSEL_3_3V          (1 << 16)
+#define AT91_MATRIX_EBI_EBI_IOSR_REDUCED        (0 << 17)
+#define AT91_MATRIX_EBI_EBI_IOSR_NORMAL         (1 << 17)
+#define AT91_MATRIX_NFD0_ON_D0                  (0 << 24)
+#define AT91_MATRIX_NFD0_ON_D16                 (1 << 24)
+#define AT91_MATRIX_MP_OFF                      (0 << 25)
+#define AT91_MATRIX_MP_ON                       (1 << 25)
+
+#endif

arch/arm/include/asm/arch-at91/hardware.h +2 -0

index 85c2889..4c4ee70 100644
@@ -37,6 +37,8 @@
  # include <asm/arch/at91sam9rl.h>
  #elif defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45)
  # include <asm/arch/at91sam9g45.h>
+#elif defined(CONFIG_AT91SAM9X5)
+# include <asm/arch/at91sam9x5.h>
  #elif defined(CONFIG_AT91CAP9)
  # include <asm/arch/at91cap9.h>
  #elif defined(CONFIG_AT91X40)

board/atmel/at91sam9x5ek/Makefile new file +1 -0

new file mode 100644
index 0000000..1c9a4b6
@@ -0,0 +1,48 @@
+#

board/atmel/at91sam9x5ek/Makefile line 7

Quoted 6 lines

board/atmel/at91sam9x5ek/Makefile new file +6 -0

+# (C) Copyright 2003-2008
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# (C) Copyright 2008
+# Stelian Pop <[email protected]>
+# Lead Tech Design <www.leadtechdesign.com>

You should add your copyright here too.

Quoted 153 lines

board/atmel/at91sam9x5ek/Makefile new file +41 -0

+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS-y += at91sam9x5ek.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################

board/atmel/at91sam9x5ek/at91sam9x5ek.c new file +105 -0

new file mode 100644
index 0000000..ff8c518
@@ -0,0 +1,306 @@
+/*
+ * Copyright (C) 2012 Atmel Corporation
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/at91sam9x5_matrix.h>
+#include <asm/arch/at91sam9_smc.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/clk.h>
+#include <lcd.h>
+#include <atmel_hlcdc.h>
+#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
+#include <net.h>
+#endif
+#include <netdev.h>
+#ifdef CONFIG_LCD_INFO
+#include <nand.h>
+#include <version.h>
+#endif
+#ifdef CONFIG_ATMEL_SPI
+#include <spi.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* ------------------------------------------------------------------------- */
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+#ifdef CONFIG_CMD_NAND
+static void at91sam9x5ek_nand_hw_init(void)
+{
+	struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
+	struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+	unsigned long csa;
+
+	/* Enable CS3 */
+	csa = readl(&matrix->ebicsa);
+	csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA;
+	writel(csa, &matrix->ebicsa);
+
+	/* Configure SMC CS3 for NAND/SmartMedia */
+	writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
+		AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
+		&smc->cs[3].setup);
+	writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(4) |
+		AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(4),
+		&smc->cs[3].pulse);
+	writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7),
+		&smc->cs[3].cycle);
+	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+		AT91_SMC_MODE_EXNW_DISABLE |
+#ifdef CONFIG_SYS_NAND_DBW_16
+		AT91_SMC_MODE_DBW_16 |
+#else /* CONFIG_SYS_NAND_DBW_8 */
+		AT91_SMC_MODE_DBW_8 |
+#endif
+		AT91_SMC_MODE_TDF_CYCLE(3),
+		&smc->cs[3].mode);
+
+	writel(1 << ATMEL_ID_PIOCD, &pmc->pcer);
+
+	/* Configure RDY/BSY */
+	at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
+	/* Enable NandFlash */
+	at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
+
+	at91_set_a_periph(AT91_PIO_PORTD, 0, 1);	/* NAND OE */
+	at91_set_a_periph(AT91_PIO_PORTD, 1, 1);	/* NAND WE */
+	at91_set_a_periph(AT91_PIO_PORTD, 2, 1);	/* NAND ALE */
+	at91_set_a_periph(AT91_PIO_PORTD, 3, 1);	/* NAND CLE */
+	at91_set_a_periph(AT91_PIO_PORTD, 6, 1);
+	at91_set_a_periph(AT91_PIO_PORTD, 7, 1);
+	at91_set_a_periph(AT91_PIO_PORTD, 8, 1);
+	at91_set_a_periph(AT91_PIO_PORTD, 9, 1);
+	at91_set_a_periph(AT91_PIO_PORTD, 10, 1);
+	at91_set_a_periph(AT91_PIO_PORTD, 11, 1);
+	at91_set_a_periph(AT91_PIO_PORTD, 12, 1);
+	at91_set_a_periph(AT91_PIO_PORTD, 13, 1);
+}
+#endif
+

board/atmel/at91sam9x5ek/at91sam9x5ek.c line 110

Quoted 5 lines

board/atmel/at91sam9x5ek/at91sam9x5ek.c new file +5 -0

+#ifdef CONFIG_RESET_PHY_R
+void reset_phy(void)
+{
+}
+#endif

Since this is empty now I ask myself if we could remove CONFIG_RESET_PHY_R from board include and remove this function here?

Quoted 16 lines

board/atmel/at91sam9x5ek/at91sam9x5ek.c new file +15 -0

+
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+
+#ifdef CONFIG_MACB
+	if (has_emac0())
+		rc = macb_eth_initialize(0,
+			(void *)ATMEL_BASE_EMAC0, 0x00);
+	if (has_emac1())
+		rc = macb_eth_initialize(1,
+			(void *)ATMEL_BASE_EMAC1, 0x00);
+#endif
+	return rc;
+}

board/atmel/at91sam9x5ek/at91sam9x5ek.c line 132

Quoted 7 lines

board/atmel/at91sam9x5ek/at91sam9x5ek.c new file +7 -0

+
+#ifdef CONFIG_MACB
+static void at91sam9x5ek_macb_hw_init(void)
+{
+	at91_macb_hw_init();
+}
+#endif

This one could also be removed.

Quoted 154 lines

board/atmel/at91sam9x5ek/at91sam9x5ek.c new file +154 -0

+
+#ifdef CONFIG_LCD
+vidinfo_t panel_info = {
+	.vl_col	= 800,
+	.vl_row = 480,
+	.vl_clk = 24000000,
+	.vl_sync = LCDC_LCDCFG5_HSPOL | LCDC_LCDCFG5_VSPOL,
+	.vl_bpix = LCD_BPP,
+	.vl_tft = 1,
+	.vl_clk_pol = 1,
+	.vl_hsync_len = 128,
+	.vl_left_margin = 64,
+	.vl_right_margin = 64,
+	.vl_vsync_len = 2,
+	.vl_upper_margin = 22,
+	.vl_lower_margin = 21,
+	.mmio = ATMEL_BASE_LCDC,
+};
+
+void lcd_enable(void)
+{
+	if (has_lcdc())
+		at91_set_a_periph(AT91_PIO_PORTC, 29, 1);	/* power up */
+}
+
+void lcd_disable(void)
+{
+	if (has_lcdc())
+		at91_set_a_periph(AT91_PIO_PORTC, 29, 0);	/* power down */
+}
+
+static void at91sam9x5ek_lcd_hw_init(void)
+{
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
+	if (has_lcdc()) {
+		at91_set_a_periph(AT91_PIO_PORTC, 26, 0);	/* LCDPWM */
+		at91_set_a_periph(AT91_PIO_PORTC, 27, 0);	/* LCDVSYNC */
+		at91_set_a_periph(AT91_PIO_PORTC, 28, 0);	/* LCDHSYNC */
+		at91_set_a_periph(AT91_PIO_PORTC, 24, 0);	/* LCDDISP */
+		at91_set_a_periph(AT91_PIO_PORTC, 29, 0);	/* LCDDEN */
+		at91_set_a_periph(AT91_PIO_PORTC, 30, 0);	/* LCDPCK */
+
+		at91_set_a_periph(AT91_PIO_PORTC, 0, 0);	/* LCDD0 */
+		at91_set_a_periph(AT91_PIO_PORTC, 1, 0);	/* LCDD1 */
+		at91_set_a_periph(AT91_PIO_PORTC, 2, 0);	/* LCDD2 */
+		at91_set_a_periph(AT91_PIO_PORTC, 3, 0);	/* LCDD3 */
+		at91_set_a_periph(AT91_PIO_PORTC, 4, 0);	/* LCDD4 */
+		at91_set_a_periph(AT91_PIO_PORTC, 5, 0);	/* LCDD5 */
+		at91_set_a_periph(AT91_PIO_PORTC, 6, 0);	/* LCDD6 */
+		at91_set_a_periph(AT91_PIO_PORTC, 7, 0);	/* LCDD7 */
+		at91_set_a_periph(AT91_PIO_PORTC, 8, 0);	/* LCDD8 */
+		at91_set_a_periph(AT91_PIO_PORTC, 9, 0);	/* LCDD9 */
+		at91_set_a_periph(AT91_PIO_PORTC, 10, 0);	/* LCDD10 */
+		at91_set_a_periph(AT91_PIO_PORTC, 11, 0);	/* LCDD11 */
+		at91_set_a_periph(AT91_PIO_PORTC, 12, 0);	/* LCDD12 */
+		at91_set_a_periph(AT91_PIO_PORTC, 13, 0);	/* LCDD13 */
+		at91_set_a_periph(AT91_PIO_PORTC, 14, 0);	/* LCDD14 */
+		at91_set_a_periph(AT91_PIO_PORTC, 15, 0);	/* LCDD15 */
+		at91_set_a_periph(AT91_PIO_PORTC, 16, 0);	/* LCDD16 */
+		at91_set_a_periph(AT91_PIO_PORTC, 17, 0);	/* LCDD17 */
+		at91_set_a_periph(AT91_PIO_PORTC, 18, 0);	/* LCDD18 */
+		at91_set_a_periph(AT91_PIO_PORTC, 19, 0);	/* LCDD19 */
+		at91_set_a_periph(AT91_PIO_PORTC, 20, 0);	/* LCDD20 */
+		at91_set_a_periph(AT91_PIO_PORTC, 21, 0);	/* LCDD21 */
+		at91_set_a_periph(AT91_PIO_PORTC, 22, 0);	/* LCDD22 */
+		at91_set_a_periph(AT91_PIO_PORTC, 23, 0);	/* LCDD23 */
+
+		writel(1 << ATMEL_ID_LCDC, &pmc->pcer);
+	}
+}
+
+#ifdef CONFIG_LCD_INFO
+void lcd_show_board_info(void)
+{
+	ulong dram_size, nand_size;
+	int i;
+	char temp[32];
+
+	if (has_lcdc()) {
+		lcd_printf("%s\n", U_BOOT_VERSION);
+		lcd_printf("(C) 2012 ATMEL Corp\n");
+		lcd_printf("at91support at atmel.com\n");
+		lcd_printf("%s CPU at %s MHz\n",
+			get_cpu_name(),
+			strmhz(temp, get_cpu_clk_rate()));
+
+		dram_size = 0;
+		for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
+			dram_size += gd->bd->bi_dram[i].size;
+		nand_size = 0;
+		for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
+			nand_size += nand_info[i].size;
+		lcd_printf("  %ld MB SDRAM, %ld MB NAND\n",
+			dram_size >> 20,
+			nand_size >> 20);
+	}
+}
+#endif /* CONFIG_LCD_INFO */
+#endif /* CONFIG_LCD */
+
+/* SPI chip select control */
+#ifdef CONFIG_ATMEL_SPI
+int spi_cs_is_valid(unsigned int bus, unsigned int cs)
+{
+	return bus == 0 && cs < 2;
+}
+
+void spi_cs_activate(struct spi_slave *slave)
+{
+	switch (slave->cs) {
+	case 1:
+		at91_set_gpio_output(AT91_PIN_PA7, 0);
+		break;
+	case 0:
+	default:
+		at91_set_gpio_output(AT91_PIN_PA14, 0);
+		break;
+	}
+}
+
+void spi_cs_deactivate(struct spi_slave *slave)
+{
+	switch (slave->cs) {
+	case 1:
+		at91_set_gpio_output(AT91_PIN_PA7, 1);
+		break;
+	case 0:
+	default:
+		at91_set_gpio_output(AT91_PIN_PA14, 1);
+		break;
+	}
+}
+#endif /* CONFIG_ATMEL_SPI */
+
+int board_early_init_f(void)
+{
+	at91_seriald_hw_init();
+	return 0;
+}
+
+int board_init(void)
+{
+	/* arch number of ATMELEK-Board */
+	gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9X5EK;
+
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+#ifdef CONFIG_CMD_NAND
+	at91sam9x5ek_nand_hw_init();
+#endif
+
+#ifdef CONFIG_ATMEL_SPI

board/atmel/at91sam9x5ek/at91sam9x5ek.c line 292

Quoted 6 lines

board/atmel/at91sam9x5ek/at91sam9x5ek.c new file +6 -0

+	at91_spi0_hw_init(1 << 0);
+	at91_spi0_hw_init(1 << 4);
+#endif
+
+#ifdef CONFIG_MACB
+	at91sam9x5ek_macb_hw_init();

can't we just use 'at91_macb_hw_init()' here?

Quoted 61 lines

board/atmel/at91sam9x5ek/at91sam9x5ek.c new file +14 -0

+#endif
+
+#ifdef CONFIG_LCD
+	at91sam9x5ek_lcd_hw_init();
+#endif
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *) CONFIG_SYS_SDRAM_BASE,
+					CONFIG_SYS_SDRAM_SIZE);
+	return 0;
+}

board/atmel/at91sam9x5ek/config.mk new file +1 -0

new file mode 100644
index 0000000..6589a12
@@ -0,0 +1 @@
+CONFIG_SYS_TEXT_BASE = 0x26f00000

boards.cfg +1 -0

index 9205070..c9bd1b3 100644
@@ -89,6 +89,7 @@ at91sam9g20ek_nandflash      arm         arm926ejs   at91sam9260ek       atmel
  at91sam9m10g45ek_nandflash   arm         arm926ejs   at91sam9m10g45ek    atmel          at91        at91sam9m10g45ek:AT91SAM9M10G45,SYS_USE_NANDFLASH
  at91sam9rlek_dataflash       arm         arm926ejs   at91sam9rlek        atmel          at91        at91sam9rlek:AT91SAM9RL,SYS_USE_DATAFLASH
  at91sam9rlek_nandflash       arm         arm926ejs   at91sam9rlek        atmel          at91        at91sam9rlek:AT91SAM9RL,SYS_USE_NANDFLASH
+at91sam9x5ek_nandflash       arm         arm926ejs   at91sam9x5ek        atmel          at91        at91sam9x5ek:AT91SAM9X5,SYS_USE_NANDFLASH
  at91sam9xeek_dataflash_cs0   arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9XE,SYS_USE_DATAFLASH_CS0
  at91sam9xeek_dataflash_cs1   arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9XE,SYS_USE_DATAFLASH_CS1
  at91sam9xeek_nandflash       arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9XE,SYS_USE_NANDFLASH

drivers/net/macb.c +2 -2

index 4578467..8f55cdc 100644
@@ -471,7 +471,7 @@ static int macb_init(struct eth_device *netdev, bd_t *bd)
  #if	defined(CONFIG_AT91CAP9) || defined(CONFIG_AT91SAM9260) || \
  	defined(CONFIG_AT91SAM9263) || defined(CONFIG_AT91SAM9G20) || \
  	defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45) || \
-	defined(CONFIG_AT91SAM9XE)
+	defined(CONFIG_AT91SAM9XE) || defined(CONFIG_AT91SAM9X5)
  	macb_writel(macb, USRIO, MACB_BIT(RMII) | MACB_BIT(CLKEN));
  #else
  	macb_writel(macb, USRIO, 0);

@@ -480,7 +480,7 @@ static int macb_init(struct eth_device *netdev, bd_t *bd)
  #if	defined(CONFIG_AT91CAP9) || defined(CONFIG_AT91SAM9260) || \
  	defined(CONFIG_AT91SAM9263) || defined(CONFIG_AT91SAM9G20) || \
  	defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45) || \
-	defined(CONFIG_AT91SAM9XE)
+	defined(CONFIG_AT91SAM9XE) || defined(CONFIG_AT91SAM9X5)
  	macb_writel(macb, USRIO, MACB_BIT(CLKEN));
  #else
  	macb_writel(macb, USRIO, MACB_BIT(MII));

drivers/serial/atmel_usart.h +0 -0

index 7e4b2c9..ad1d9f0 100644

drivers/serial/atmel_usart.h typedef struct atmel_usart3 { · line 41

Quoted 7 lines

drivers/serial/atmel_usart.h +2 -2

@@ -37,8 +37,8 @@ typedef struct atmel_usart3 {
  	u32	rtor;
  	u32	ttgr;
  	u32	reserved0[5];
-	u32	fidi;
-	u32	ner;
+	u32	fidi;		/* cidr for dbgu */
+	u32	ner;		/* exid for dbgu */

NAK

Quoted 7 lines

drivers/serial/atmel_usart.h +0 -0

  	u32	reserved1;
  	u32	ifr;
  	u32	man;

@@ -289,6 +289,9 @@ typedef struct atmel_usart3 {
  /* Constants for FI_DI_RATIO */
  #define USART3_FI_DI_RATIO_DISABLE		0
 

drivers/serial/atmel_usart.h typedef struct atmel_usart3 { · line 294

Quoted 3 lines

drivers/serial/atmel_usart.h +3 -0

+/* chip revision mask */
+#define AT91_CIDR_VERSION			0x1f
+

NAK, this belongs to DBGU and not to USART. I think one of the specific hardware.h would be a good place for that.

Quoted 43 lines

drivers/serial/atmel_usart.h +0 -0

  /* Bit manipulation macros */
  #define USART3_BIT(name)				\
  	(1 << USART3_##name##_OFFSET)

include/configs/at91sam9x5ek.h new file +33 -0

new file mode 100644
index 0000000..9aba52c
@@ -0,0 +1,201 @@
+/*
+ * Copyright (C) 2012 Atmel Corporation
+ *
+ * Configuation settings for the AT91SAM9X5EK board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H__
+#define __CONFIG_H__
+
+#include <asm/hardware.h>
+
+/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_SLOW_CLOCK	32768
+#define CONFIG_SYS_AT91_MAIN_CLOCK	12000000	/* 12 MHz crystal */
+#define CONFIG_SYS_HZ			1000

include/configs/at91sam9x5ek.h line 39

Quoted 6 lines

include/configs/at91sam9x5ek.h new file +6 -0

+
+#define CONFIG_AT91SAM9X5EK
+#define CONFIG_AT91FAMILY
+
+#define CONFIG_ARCH_CPU_INIT
+#undef CONFIG_USE_IRQ			/* we don't need IRQ/FIQ stuff */

Hmm ... who defined it before?

Quoted 42 lines

include/configs/at91sam9x5ek.h new file +41 -0

+
+#define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_DISPLAY_CPUINFO
+
+/* general purpose I/O */
+#define CONFIG_ATMEL_LEGACY		/* required until (g)pio is fixed */
+#define CONFIG_AT91_GPIO
+
+/* serial console */
+#define CONFIG_ATMEL_USART
+#define CONFIG_USART_BASE	ATMEL_BASE_DBGU
+#define CONFIG_USART_ID		ATMEL_ID_SYS
+
+/* LCD */
+#define CONFIG_LCD
+#define LCD_BPP			LCD_COLOR16
+#define LCD_OUTPUT_BPP		24
+#define CONFIG_LCD_LOGO
+#undef LCD_TEST_PATTERN
+#define CONFIG_LCD_INFO
+#define CONFIG_LCD_INFO_BELOW_LOGO
+#define CONFIG_SYS_WHITE_ON_BLACK
+#define CONFIG_ATMEL_HLCD
+#define CONFIG_ATMEL_LCD_RGB565
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+
+#define CONFIG_BOOTDELAY	3
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*

include/configs/at91sam9x5ek.h line 84

Quoted 4 lines

include/configs/at91sam9x5ek.h new file +4 -0

+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_BDI

I cound BDI a really useful command, please let this one in. Undefining the rest is ok with me. But keep in mind that you remove commands other u-boot have, this may confuse users.

include/configs/at91sam9x5ek.h line 88

Quoted 5 lines

include/configs/at91sam9x5ek.h new file +4 -0

+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IMI
+#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_AUTOSCRIPT

CONFIG_CMD_AUTOSCRIPT is unknown, please remove

Quoted 46 lines

include/configs/at91sam9x5ek.h new file +45 -0

+#undef CONFIG_CMD_LOADS
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NAND
+
+/* SDRAM */
+#define CONFIG_NR_DRAM_BANKS		1
+#define CONFIG_SYS_SDRAM_BASE		0x20000000
+#define CONFIG_SYS_SDRAM_SIZE		0x08000000	/* 128 megs */
+
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
+
+/* DataFlash */
+#ifdef CONFIG_ATMEL_SPI
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_ATMEL
+#define CONFIG_SYS_MAX_DATAFLASH_BANKS
+#endif
+
+/* no NOR flash */
+#define CONFIG_SYS_NO_FLASH
+
+/* NAND flash */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_ATMEL
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		0x40000000
+#define CONFIG_SYS_NAND_DBW_8		1
+/* our ALE is AD21 */
+#define CONFIG_SYS_NAND_MASK_ALE	(1 << 21)
+/* our CLE is AD22 */
+#define CONFIG_SYS_NAND_MASK_CLE	(1 << 22)
+#define CONFIG_SYS_NAND_ENABLE_PIN	AT91_PIN_PD4
+#define CONFIG_SYS_NAND_READY_PIN	AT91_PIN_PD5
+
+#define CONFIG_MTD_DEVICE
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+#define CONFIG_CMD_UBI

include/configs/at91sam9x5ek.h line 140

Quoted 7 lines

include/configs/at91sam9x5ek.h new file +7 -0

+#define CONFIG_CMD_UBIFS
+#endif
+
+/* Ethernet */
+#define CONFIG_MACB
+#define CONFIG_RMII
+#define CONFIG_NET_MULTI

CONFIG_NET_MULTI was removed in 31a4f1e5b6ee9b6335f0313dce7637cef887f84f

include/configs/at91sam9x5ek.h line 142

Quoted 3 lines

include/configs/at91sam9x5ek.h new file +2 -0

+#define CONFIG_NET_RETRY_COUNT		20
+#define CONFIG_RESET_PHY_R

I think this one could be removed.

include/configs/at91sam9x5ek.h line 150

Quoted 9 lines

include/configs/at91sam9x5ek.h new file +8 -0

+#define CONFIG_MACB_SEARCH_PHY
+
+#define CONFIG_SYS_LOAD_ADDR		0x22000000	/* load address */
+
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END		0x26e00000
+
+#ifdef CONFIG_SYS_USE_DATAFLASH

dataflash is not implemented currently, is it?

Quoted 17 lines

include/configs/at91sam9x5ek.h new file +16 -0

+
+/* bootstrap + u-boot + env + linux in dataflash on CS0 */
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SYS_MONITOR_BASE	(0x10000000 + 0x8400)
+#define CONFIG_ENV_OFFSET	0x5000
+#define CONFIG_ENV_ADDR		(0x10000000 + CONFIG_ENV_OFFSET)
+#define CONFIG_ENV_SIZE		0x3000
+#define CONFIG_ENV_SECT_SIZE	0x1000
+#define CONFIG_BOOTCOMMAND	"sf probe 0; " \
+				"sf read 0x22000000 0x42000 0x300000; " \
+				"bootm 0x22000000"
+#else /* CONFIG_SYS_USE_NANDFLASH */
+
+/* bootstrap + u-boot + env + linux in nandflash */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET		0xc0000

include/configs/at91sam9x5ek.h line 171

Quoted 5 lines

include/configs/at91sam9x5ek.h new file +5 -0

+#define CONFIG_ENV_OFFSET_REDUND	0x100000
+#define CONFIG_ENV_SIZE		0x20000		/* 1 sector = 128 kB */
+#define CONFIG_BOOTCOMMAND	"nand read.jffs2 " \
+				"0x22000000 0x200000 0x300000; " \
+				"bootm 0x22000000"

Well, you read from jffs but work with ubifs later on? Is that ok?
BTW: I do not know 'nand read.jffs2', does this subcommand exist really?

Quoted 22 lines

include/configs/at91sam9x5ek.h new file +20 -0

+#endif
+
+#define CONFIG_BOOTARGS		"mem=128M console=ttyS0,115200 " \
+				"mtdparts=atmel_nand:" \
+				"8M(bootstrap/uboot/kernel)ro,-(rootfs) " \
+				"root=/dev/mtdblock1 rw " \
+				"rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs"
+
+#define CONFIG_BAUDRATE		115200
+
+#define CONFIG_SYS_PROMPT	"U-Boot> "
+#define CONFIG_SYS_CBSIZE	256
+#define CONFIG_SYS_MAXARGS	16
+#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) \
+					+ 16)
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_HUSH_PARSER
+

include/configs/at91sam9x5ek.h line 201

Quoted 10 lines

include/configs/at91sam9x5ek.h new file +10 -0

+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN		(512 * 1024 + 0x1000)
+
+#ifdef CONFIG_USE_IRQ
+#error CONFIG_USE_IRQ not supported
+#endif
+
+#endif

I think a v3 should make it into the tree. Please send next days cause I plan to send the pull request end of this week at the latest.

Best regards

Andreas Bie?mann
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Hi Andreas,

Quoted 3 lines · Andreas Bie?mann

Dear Bo Shen,

On 02.07.12 05:35, Bo Shen wrote:

Quoted 21 lines

drivers/serial/atmel_usart.h typedef struct atmel_usart3 { · line 41

Quoted 12 lines

drivers/serial/atmel_usart.h +2 -2

index 7e4b2c9..ad1d9f0 100644
@@ -37,8 +37,8 @@ typedef struct atmel_usart3 {
      u32    rtor;
      u32    ttgr;
      u32    reserved0[5];
-    u32    fidi;
-    u32    ner;
+    u32    fidi;        /* cidr for dbgu */
+    u32    ner;        /* exid for dbgu */

NAK

Quoted 7 lines

drivers/serial/atmel_usart.h +0 -0

      u32    reserved1;
      u32    ifr;
      u32    man;

@@ -289,6 +289,9 @@ typedef struct atmel_usart3 {
  /* Constants for FI_DI_RATIO */
  #define USART3_FI_DI_RATIO_DISABLE        0
 

Quoted 5 lines

drivers/serial/atmel_usart.h typedef struct atmel_usart3 { · line 294

Quoted 3 lines

drivers/serial/atmel_usart.h +3 -0

+/* chip revision mask */
+#define AT91_CIDR_VERSION            0x1f
+

NAK, this belongs to DBGU and not to USART. I think one of the specific hardware.h would be a good place for that.

I will move it into at91sam9x5.h file.

Quoted 11 lines

drivers/serial/atmel_usart.h typedef struct atmel_usart3 {

Quoted 9 lines

drivers/serial/atmel_usart.h +8 -0

+#define CONFIG_MACB_SEARCH_PHY
+
+#define CONFIG_SYS_LOAD_ADDR        0x22000000    /* load address */
+
+#define CONFIG_SYS_MEMTEST_START    CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END        0x26e00000
+
+#ifdef CONFIG_SYS_USE_DATAFLASH

dataflash is not implemented currently, is it?

Yes. At this stage, it doesn't implement yet.

Quoted 18 lines

Quoted 18 lines

drivers/serial/atmel_usart.h +16 -0

+
+/* bootstrap + u-boot + env + linux in dataflash on CS0 */
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SYS_MONITOR_BASE    (0x10000000 + 0x8400)
+#define CONFIG_ENV_OFFSET    0x5000
+#define CONFIG_ENV_ADDR        (0x10000000 + CONFIG_ENV_OFFSET)
+#define CONFIG_ENV_SIZE        0x3000
+#define CONFIG_ENV_SECT_SIZE    0x1000
+#define CONFIG_BOOTCOMMAND    "sf probe 0; " \
+                "sf read 0x22000000 0x42000 0x300000; " \
+                "bootm 0x22000000"
+#else /* CONFIG_SYS_USE_NANDFLASH */
+
+/* bootstrap + u-boot + env + linux in nandflash */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET        0xc0000

Quoted 8 lines

drivers/serial/atmel_usart.h

Quoted 5 lines

drivers/serial/atmel_usart.h +5 -0

+#define CONFIG_ENV_OFFSET_REDUND    0x100000
+#define CONFIG_ENV_SIZE        0x20000        /* 1 sector = 128 kB */
+#define CONFIG_BOOTCOMMAND    "nand read.jffs2 " \
+                "0x22000000 0x200000 0x300000; " \
+                "bootm 0x22000000"

Well, you read from jffs but work with ubifs later on? Is that ok?
BTW: I do not know 'nand read.jffs2', does this subcommand exist really?

Using the read with subfix .jffs2 it to skip the bad block. This partition is for Linux kernel.
I will remove the .jffs2 to avoid confusing.

Quoted 12 lines

Quoted 11 lines

include/configs/at91sam9x5ek.h line 171

Quoted 8 lines

include/configs/at91sam9x5ek.h new file +8 -0

+/* bootstrap + u-boot + env + linux in nandflash */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET        0xc0000
+#define CONFIG_ENV_OFFSET_REDUND    0x100000
+#define CONFIG_ENV_SIZE        0x20000        /* 1 sector = 128 kB */
+#define CONFIG_BOOTCOMMAND    "nand read.jffs2 " \
+                "0x22000000 0x200000 0x300000; " \
+                "bootm 0x22000000"

Well, you read from jffs but work with ubifs later on? Is that ok?
BTW: I do not know 'nand read.jffs2', does this subcommand exist really?

Quoted 3 lines

Using the read with subfix .jffs2 it to skip the bad block. This partition is for Linux kernel.
I will remove the .jffs2 to avoid confusing.

Well, it is ok with me to use read.jffs2 (if it works). I just do not know about that subcommand and I can only find some references about that in two other boards. I guess these boards are just forgotten while removing the 'nand read.jffs2' command. Please check, if that command works, if yes let it as is, if not rewrite.

On 07/02/2012 11:47 AM, Andreas Bie?mann :

Quoted 1 line · Bo Shen

[..]

Quoted 16 lines

Quoted 12 lines

Quoted 11 lines

include/configs/at91sam9x5ek.h line 171

Quoted 8 lines

include/configs/at91sam9x5ek.h new file +8 -0

+/* bootstrap + u-boot + env + linux in nandflash */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET        0xc0000
+#define CONFIG_ENV_OFFSET_REDUND    0x100000
+#define CONFIG_ENV_SIZE        0x20000        /* 1 sector = 128 kB */
+#define CONFIG_BOOTCOMMAND    "nand read.jffs2 " \
+                "0x22000000 0x200000 0x300000; " \
+                "bootm 0x22000000"

Well, you read from jffs but work with ubifs later on? Is that ok?
BTW: I do not know 'nand read.jffs2', does this subcommand exist really?

Quoted 3 lines

Using the read with subfix .jffs2 it to skip the bad block. This partition is for Linux kernel.
I will remove the .jffs2 to avoid confusing.

Quoted 5 lines

Well, it is ok with me to use read.jffs2 (if it works). I just do not know about that subcommand and I can only find some references about that in two other boards. I guess these boards are just forgotten while removing the 'nand read.jffs2' command. Please check, if that command works, if yes let it as is, if not rewrite.

I am in favor of using read.jffs2 because it is able to skip bad blocks. As the programming tool is also skipping bad blocks the same way, we have a configuration that is perfectly working even in case of bad block in the middle of the kernel image.

So please, keep using read.jffs2 (or equivalent)!

Dear all,

Quoted 27 lines · Nicolas Ferre

On 07/02/2012 11:47 AM, Andreas Bie?mann :

Quoted 1 line · Bo Shen

[..]

Quoted 16 lines

Quoted 12 lines

Quoted 11 lines

include/configs/at91sam9x5ek.h line 171

Quoted 8 lines

include/configs/at91sam9x5ek.h new file +8 -0

+/* bootstrap + u-boot + env + linux in nandflash */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET        0xc0000
+#define CONFIG_ENV_OFFSET_REDUND    0x100000
+#define CONFIG_ENV_SIZE        0x20000        /* 1 sector = 128 kB */
+#define CONFIG_BOOTCOMMAND    "nand read.jffs2 " \
+                "0x22000000 0x200000 0x300000; " \
+                "bootm 0x22000000"

Well, you read from jffs but work with ubifs later on? Is that ok?
BTW: I do not know 'nand read.jffs2', does this subcommand exist really?

Quoted 3 lines

Using the read with subfix .jffs2 it to skip the bad block. This partition is for Linux kernel.
I will remove the .jffs2 to avoid confusing.

Quoted 5 lines

Well, it is ok with me to use read.jffs2 (if it works). I just do not know about that subcommand and I can only find some references about that in two other boards. I guess these boards are just forgotten while removing the 'nand read.jffs2' command. Please check, if that command works, if yes let it as is, if not rewrite.

Quoted 6 lines

I am in favor of using read.jffs2 because it is able to skip bad blocks. As the programming tool is also skipping bad blocks the same way, we have a configuration that is perfectly working even in case of bad block in the middle of the kernel image.

So please, keep using read.jffs2 (or equivalent)!

I have the same opinion here, we should skip bad blocks. But I think 'nand read.jffs2' is not available any longer.

from current common/cmd_nand.c:
---8<---
"nand read - addr off|partition size\n" "nand write - addr off|partition size\n"
" read/write 'size' bytes starting at offset 'off'\n"
" to/from memory address 'addr', skipping bad blocks.\n"
"nand read.raw - addr off|partition [count]\n" "nand write.raw - addr off|partition [count]\n"
" Use read.raw/write.raw to avoid ECC and access the flash as-is.\n"
--->8---

Dear all,

Quoted 27 lines · Nicolas Ferre

On 07/02/2012 11:47 AM, Andreas Bie?mann :

Quoted 1 line · Bo Shen

[..]

Quoted 16 lines

Quoted 12 lines

Quoted 11 lines

include/configs/at91sam9x5ek.h line 171

Quoted 8 lines

include/configs/at91sam9x5ek.h new file +8 -0

+/* bootstrap + u-boot + env + linux in nandflash */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET        0xc0000
+#define CONFIG_ENV_OFFSET_REDUND    0x100000
+#define CONFIG_ENV_SIZE        0x20000        /* 1 sector = 128 kB */
+#define CONFIG_BOOTCOMMAND    "nand read.jffs2 " \
+                "0x22000000 0x200000 0x300000; " \
+                "bootm 0x22000000"

Well, you read from jffs but work with ubifs later on? Is that ok?
BTW: I do not know 'nand read.jffs2', does this subcommand exist really?

Quoted 3 lines

Using the read with subfix .jffs2 it to skip the bad block. This partition is for Linux kernel.
I will remove the .jffs2 to avoid confusing.

Quoted 5 lines

Well, it is ok with me to use read.jffs2 (if it works). I just do not know about that subcommand and I can only find some references about that in two other boards. I guess these boards are just forgotten while removing the 'nand read.jffs2' command. Please check, if that command works, if yes let it as is, if not rewrite.

Quoted 6 lines

I am in favor of using read.jffs2 because it is able to skip bad blocks. As the programming tool is also skipping bad blocks the same way, we have a configuration that is perfectly working even in case of bad block in the middle of the kernel image.

So please, keep using read.jffs2 (or equivalent)!

I have the same opinion here, we should skip bad blocks. But I think 'nand read.jffs2' is not available any longer.

from current common/cmd_nand.c:
---8<---
"nand read - addr off|partition size\n" "nand write - addr off|partition size\n"
" read/write 'size' bytes starting at offset 'off'\n"
" to/from memory address 'addr', skipping bad blocks.\n"
"nand read.raw - addr off|partition [count]\n" "nand write.raw - addr off|partition [count]\n"
" Use read.raw/write.raw to avoid ECC and access the flash as-is.\n"
--->8---