Pull request: u-boot-imx

Hi Albert,

please pull from u-boot-imx. Thanks !

The following changes since commit 3e0cac6b5158b22248f57cdf7769bf8d610fec5e:

EXYNOS: SMDK5250: Enable the pinmux setup (2012-06-25 22:51:36 +0200)

are available in the git repository at:

git://www.denx.de/git/u-boot-imx.git master

for you to fetch changes up to c45272e25bdf241fbb27638465f16ce2342ed1b6:

i.MX6 USDHC: Use the ESDHC clock (2012-07-02 19:53:20 +0200)

----------------------------------------------------------------
Fabio Estevam (21):
mx53loco: Fix revision of Dialog boards
mx53: Fix mask for SATA reference clock
mx53loco: Remove unused SOBJS
mx53evk: Remove unused SOBJS
mx53ard: Remove unused SOBJS
mx53smd: Remove unused SOBJS
mx51evk: Remove unused SOBJS
efikamx: Remove unused SOBJS
vision2: Remove unused SOBJS
ima3-mx53: Remove unused SOBJS
mx6qarm2: Remove unused SOBJS
mx6qsabrelite: Remove unused SOBJS
mx53ard: Remove unused CONFIG_MII_GASKET
imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition
mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definition
mx53ard: Remove CONFIG_SYS_I2C_SLAVE definition
mx53evk: Remove CONFIG_SYS_I2C_SLAVE definition
mx53loco: Remove CONFIG_SYS_I2C_SLAVE definition
mx53smd: Remove CONFIG_SYS_I2C_SLAVE definition
mx28evk: Fix PSWITCH key position
mx28evk: Fix boot by adjusting HW_DRAM_CTL29 register

Jason Liu (1):
i.mx: i.mx6x: NO_MUX_I/NO_PAD_I not set correctly

Marek Vasut (1):
i.MX28: Add function to adjust memory parameters

Michael Langer (1):
i.MX6 USDHC: Use the ESDHC clock

Otavio Salvador (6):
MX28: Fix a typo in mx28_reg_8 macro
m28evk: fix board config include guardian macro name
mx28evk: ensure command definition is in alphabetic order
mx28evk: fix board config include guardian macro name
m28evk: drop duplicated definition of CONFIG_OF_LIBFDT
m28evk: use same notation to alloc the 128kB stack

Vikram Narayanan (1):
mx6: Avoid writing to read-only bits in imximage.cfg

 arch/arm/cpu/arm926ejs/mx28/spl_mem_init.c   |    8 ++++++++
 arch/arm/cpu/armv7/imx-common/speed.c        |    4 ++++
 arch/arm/cpu/armv7/mx5/clock.c               |    2 +-
 arch/arm/include/asm/arch-mx28/regs-common.h |    2 +-
 arch/arm/include/asm/arch-mx6/mx6x_pins.h    |    4 ++--
 board/efikamx/Makefile                       |    7 +++----
 board/esg/ima3-mx53/Makefile                 |    2 +-
 board/freescale/mx28evk/iomux.c              |   14 ++++++++++++++
 board/freescale/mx51evk/Makefile             |    7 +++----
 board/freescale/mx53ard/Makefile             |    7 +++----
 board/freescale/mx53evk/Makefile             |    7 +++----
 board/freescale/mx53loco/Makefile            |    7 +++----
 board/freescale/mx53loco/mx53loco.c          |   12 +++++++-----
 board/freescale/mx53smd/Makefile             |    7 +++----
 board/freescale/mx6qarm2/Makefile            |    7 +++----
 board/freescale/mx6qarm2/imximage.cfg        |    2 +-
 board/freescale/mx6qsabrelite/Makefile       |    7 +++----
 board/freescale/mx6qsabrelite/imximage.cfg   |    2 +-
 board/ttcontrol/vision2/Makefile             |    5 ++---
 doc/README.mx28evk                           |    2 +-
 include/configs/imx31_phycore.h              |    1 -
 include/configs/m28evk.h                     |   10 ++++------
 include/configs/mx28evk.h                    |    8 ++++----
 include/configs/mx35pdk.h                    |    1 -
 include/configs/mx53ard.h                    |    2 --
 include/configs/mx53evk.h                    |    1 -
 include/configs/mx53loco.h                   |    2 --
 include/configs/mx53smd.h                    |    1 -
 28 files changed, 75 insertions(+), 66 deletions(-)

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

Hi Stefano,

Applied, thanks.

Amicalement,

Albert.