Skip to contentSkip to conversation

arm64: dts: mt8183-kukui: Add tboard thermal zones

PATCH Applied Ben Tseng 2 participants 2 messages Jun 4, 2021 – Jun 9, 2021

Subsystems (2)
lore
Share & tools
lore

Ben Tseng

author
#0 lore raw

PATCH v3 1/1 arm64: dts: mt8183-kukui: Add tboard thermal zones

From: Michael Kao <[email protected]>

Add tboard thermal zones.
The tboard thermal sensors are a kind of NTC sensors which are located on PCB board to correlate the temperature of the case (Tskin).

pull-up voltage: 1800 mv
pull-up resistor: 75K

Vsense = pull-up voltage * Rntc / ( pull-up resistor + Rntc ) AuxIn = Vsense * 4096 / 1500

---
Change in v3:
- Modify Tboard to tbaord in mt8183-kukui.dtsi
- Add more description about tboard thermal sensor

Change in v2:
- Rebase to kernel-v5.13-rc1
- Resend

---
 arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi | 14 ++++++++++++++
 arch/arm64/boot/dts/mediatek/mt8183.dtsi       |  2 +-
 2 files changed, 15 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi +14 -0
index ff56bcf..601f866 100644
@@ -847,6 +847,20 @@
 	status = "okay";
 };
 
+&thermal_zones {
+	tboard1 {
+		polling-delay = <1000>; /* milliseconds */
+		polling-delay-passive = <0>; /* milliseconds */
+		thermal-sensors = <&tboard_thermistor1>;
+	};
+
+	tboard2 {
+		polling-delay = <1000>; /* milliseconds */
+		polling-delay-passive = <0>; /* milliseconds */
+		thermal-sensors = <&tboard_thermistor2>;
+	};
+};
+
 &u3phy {
 	status = "okay";
 };
arch/arm64/boot/dts/mediatek/mt8183.dtsi +1 -1
index c5e822b..4173a5d 100644
@@ -673,7 +673,7 @@
 			nvmem-cell-names = "calibration-data";
 		};
 
-		thermal-zones {
+		thermal_zones: thermal-zones {
 			cpu_thermal: cpu_thermal {
 				polling-delay-passive = <100>;
 				polling-delay = <500>;
Signature · 1 line
1.8.1.1.dirty
maintainer Applied
#1 lore raw
Quoted 9 lines · Ben Tseng

From: Michael Kao <[email protected]>

Add tboard thermal zones.
The tboard thermal sensors are a kind of NTC sensors which are located on PCB board to correlate the temperature of the case (Tskin).

pull-up voltage: 1800 mv
pull-up resistor: 75K

Quoted 7 lines

Vsense = pull-up voltage * Rntc / ( pull-up resistor + Rntc ) AuxIn = Vsense * 4096 / 1500

Applied to v5.13-next/dts64

Thanks!

Quoted 52 lines

---
Change in v3:
- Modify Tboard to tbaord in mt8183-kukui.dtsi
- Add more description about tboard thermal sensor

Change in v2:
- Rebase to kernel-v5.13-rc1
- Resend

---
 arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi | 14 ++++++++++++++
 arch/arm64/boot/dts/mediatek/mt8183.dtsi       |  2 +-
 2 files changed, 15 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi +14 -0
index ff56bcf..601f866 100644
@@ -847,6 +847,20 @@
 	status = "okay";
 };
 
+&thermal_zones {
+	tboard1 {
+		polling-delay = <1000>; /* milliseconds */
+		polling-delay-passive = <0>; /* milliseconds */
+		thermal-sensors = <&tboard_thermistor1>;
+	};
+
+	tboard2 {
+		polling-delay = <1000>; /* milliseconds */
+		polling-delay-passive = <0>; /* milliseconds */
+		thermal-sensors = <&tboard_thermistor2>;
+	};
+};
+
 &u3phy {
 	status = "okay";
 };
arch/arm64/boot/dts/mediatek/mt8183.dtsi +1 -1
index c5e822b..4173a5d 100644
@@ -673,7 +673,7 @@
 			nvmem-cell-names = "calibration-data";
 		};
 
-		thermal-zones {
+		thermal_zones: thermal-zones {
 			cpu_thermal: cpu_thermal {
 				polling-delay-passive = <100>;
 				polling-delay = <500>;