Skip to contentSkip to conversation

Marvell OpenRD-Ultimate machine support

PATCH In review Dmytro Milinevskyy 3 participants 5 messages Jun 9, 2010 – Jun 10, 2010

Subsystems (2)
Arm (32-bit) Arm sub-architectures
lore
Share & tools
lore

Dmytro Milinevskyy

author
#0 lore raw

PATCH 1/1 Marvell OpenRD-Ultimate machine support

Hi!
This patch adds support for the OpenRD Ultimate machine(could be found at http://www.arm.linux.org.uk/developer/machines/list.php?id=2884)

Besides adding machine description this patch adds correction for PHY address for Ultimate version.

Differences from the previous attempt:
- Applied suggestion from Lennert Buytenhek to change PHY addresses in instances of mv643xx_eth_platform_data in case of ultimate version.

Regards,

-- Dmytro Milinevskyy

Signed-off-by Dmytro Milinevskyy <[email protected]>
---
 arch/arm/mach-kirkwood/Kconfig        |    7 +++++++
 arch/arm/mach-kirkwood/openrd-setup.c |   28 +++++++++++++++++++++++++---
 2 files changed, 32 insertions(+), 3 deletions(-)
arch/arm/mach-kirkwood/Kconfig +7 -0
index 29b2163..110a3b8 100644
@@ -75,6 +75,13 @@ config MACH_OPENRD_CLIENT
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell OpenRD Client Board.
 
+config MACH_OPENRD_ULTIMATE
+	bool "Marvell OpenRD Ultimate Board"
+	select MACH_OPENRD
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  Marvell OpenRD Ultimate Board.
+
 config MACH_NETSPACE_V2
 	bool "LaCie Network Space v2 NAS Board"
 	help
arch/arm/mach-kirkwood/openrd-setup.c +25 -3
index ad3f1ec..81b330d 100644
@@ -1,7 +1,7 @@
 /*
  * arch/arm/mach-kirkwood/openrd-setup.c
  *
- * Marvell OpenRD (Base|Client) Board Setup
+ * Marvell OpenRD (Base|Client|Ultimate) Board Setup
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2.  This program is licensed "as is" without any

@@ -73,9 +73,16 @@ static void __init openrd_init(void)
 
 	kirkwood_ehci_init();
 
+	if (machine_is_openrd_ultimate()) {
+		openrd_ge00_data.phy = 0;
+		openrd_ge01_data.phy = 1;
+	}
+
 	kirkwood_ge00_init(&openrd_ge00_data);
-	if (machine_is_openrd_client())
+	if (machine_is_openrd_client() ||
+		machine_is_openrd_ultimate())
 		kirkwood_ge01_init(&openrd_ge01_data);
+
 	kirkwood_sata_init(&openrd_sata_data);
 	kirkwood_sdio_init(&openrd_mvsdio_data);
 

@@ -84,7 +91,9 @@ static void __init openrd_init(void)
 
 static int __init openrd_pci_init(void)
 {
-	if (machine_is_openrd_base() || machine_is_openrd_client())
+	if (machine_is_openrd_base() ||
+		machine_is_openrd_client() ||
+		machine_is_openrd_ultimate())
 		kirkwood_pcie_init();
 
 	return 0;

@@ -116,3 +125,16 @@ MACHINE_START(OPENRD_CLIENT, "Marvell OpenRD Client Board")
 	.timer		= &kirkwood_timer,
 MACHINE_END
 #endif
+
+#ifdef CONFIG_MACH_OPENRD_ULTIMATE
+MACHINE_START(OPENRD_ULTIMATE, "Marvell OpenRD Ultimate Board")
+	/* Maintainer: Dhaval Vasa <[email protected]> */
+	.phys_io	= KIRKWOOD_REGS_PHYS_BASE,
+	.io_pg_offst	= ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc,
+	.boot_params	= 0x00000100,
+	.init_machine	= openrd_init,
+	.map_io		= kirkwood_map_io,
+	.init_irq	= kirkwood_init_irq,
+	.timer		= &kirkwood_timer,
+MACHINE_END
+#endif
Signature · 1 line
1.7.1
#1 lore raw

Hi,

Quoted 16 lines · Dmytro Milinevskyy

This patch adds support for the OpenRD Ultimate machine(could be found at http://www.arm.linux.org.uk/developer/machines/list.php?id=2884)

Besides adding machine description this patch adds correction for PHY address for Ultimate version.

Differences from the previous attempt:
- Applied suggestion from Lennert Buytenhek to change PHY addresses in instances of mv643xx_eth_platform_data in case of ultimate version.

Signed-off-by Dmytro Milinevskyy <[email protected]>

---

arch/arm/mach-kirkwood/openrd-setup.c static void __init openrd_init(void) · line 80

Quoted 5 lines
arch/arm/mach-kirkwood/openrd-setup.c +5 -0
+	if (machine_is_openrd_ultimate()) {
+		openrd_ge00_data.phy = 0;
+		openrd_ge01_data.phy = 1;
+	}
+

Does this even work? Surely you mean the following instead:
----

if (machine_is_openrd_ultimate()) {
	openrd_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
	openrd_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(1);
}

----

arch/arm/mach-kirkwood/openrd-setup.c static void __init openrd_init(void) · line 87

Quoted 9 lines
arch/arm/mach-kirkwood/openrd-setup.c +3 -1
 	kirkwood_ge00_init(&openrd_ge00_data);
-	if (machine_is_openrd_client())
+	if (machine_is_openrd_client() ||      \__same line
+		machine_is_openrd_ultimate())  /
 		kirkwood_ge01_init(&openrd_ge01_data);
+  <------- REMOVE
 	kirkwood_sata_init(&openrd_sata_data);
 	kirkwood_sdio_init(&openrd_mvsdio_data);

As that 'if()' clause is still less than 77 chars wide:
----
kirkwood_ge00_init(&openrd_ge00_data);
if (machine_is_openrd_client() || machine_is_openrd_ultimate())

	kirkwood_ge01_init(&openrd_ge01_data);

kirkwood_sata_init(&openrd_sata_data);
kirkwood_sdio_init(&openrd_mvsdio_data);
----

Cheers

Signature · 2 lines
Alexander Clouter
.sigmonster says: People respond to people who respond.
#2 lore raw

Hi,

Quoted 14 lines · Alexander Clouter

arch/arm/mach-kirkwood/openrd-setup.c static void __init openrd_init(void) · line 87

Quoted 10 lines
arch/arm/mach-kirkwood/openrd-setup.c +3 -1
 	kirkwood_ge00_init(&openrd_ge00_data);
-	if (machine_is_openrd_client())
+	if (machine_is_openrd_client() ||      \__same line
+		machine_is_openrd_ultimate())  /
 		kirkwood_ge01_init(&openrd_ge01_data);
+  <------- REMOVE
 	kirkwood_sata_init(&openrd_sata_data);
 	kirkwood_sdio_init(&openrd_mvsdio_data);

As that 'if()' clause is still less than 77 chars wide:
----
kirkwood_ge00_init(&openrd_ge00_data);
if (machine_is_openrd_client() || machine_is_openrd_ultimate())

Quoted 5 lines
	kirkwood_ge01_init(&openrd_ge01_data);

kirkwood_sata_init(&openrd_sata_data);
kirkwood_sdio_init(&openrd_mvsdio_data);
----

Better still, just make this 'if(!machine_is_openrd_base())'.

Cheers

Signature · 2 lines
Alexander Clouter
.sigmonster says: What this country needs is a good five cent microcomputer.
#3 lore raw
Quoted 18 lines · Alexander Clouter
Quoted 13 lines

arch/arm/mach-kirkwood/openrd-setup.c static void __init openrd_init(void) · line 87

Quoted 9 lines
arch/arm/mach-kirkwood/openrd-setup.c +3 -1
 	kirkwood_ge00_init(&openrd_ge00_data);
-	if (machine_is_openrd_client())
+	if (machine_is_openrd_client() ||      \__same line
+		machine_is_openrd_ultimate())  /
 		kirkwood_ge01_init(&openrd_ge01_data);
+  <------- REMOVE
 	kirkwood_sata_init(&openrd_sata_data);
 	kirkwood_sdio_init(&openrd_mvsdio_data);

As that 'if()' clause is still less than 77 chars wide:
----
kirkwood_ge00_init(&openrd_ge00_data);
if (machine_is_openrd_client() || machine_is_openrd_ultimate())

Quoted 4 lines
	kirkwood_ge01_init(&openrd_ge01_data);

kirkwood_sata_init(&openrd_sata_data);
kirkwood_sdio_init(&openrd_mvsdio_data);
----

Quoted 1 line

Better still, just make this 'if(!machine_is_openrd_base())'.

That form is more error prone when someone adds the OpenRD-SuperDuper, though.

author
#4 lore raw

Hi!

Quoted 6 lines
Quoted 2 lines

Better still, just make this 'if(!machine_is_openrd_base())'.

That form is more error prone when someone adds the OpenRD-SuperDuper, though.

I agree, and the similar could be done in pcie initialization.

-- Dima