Skip to contentSkip to conversation

mx6: Make pad name macro consistent with the datasheet

PATCH New Ashok 4 participants 5 messages Jun 15, 2012 – Jul 18, 2012 Arm (32-bit)

lore
Share & tools
lore

Ashok

author
#0 lore raw

PATCH 1/1 mx6: Make pad name macro consistent with the datasheet

Use the same name as defined in the datasheet.
DSP_CLK -> DISP_CLK

Signed-off-by Ashok Kumar Reddy Kourla <[email protected]>
---
 arch/arm/include/asm/arch-mx6/mx6x_pins.h |    4 ++--
 1 files changed, 2 insertions(+), 2 deletions(-)
arch/arm/include/asm/arch-mx6/mx6x_pins.h +2 -2
index afaa068..377d97f 100644
@@ -530,8 +530,8 @@ enum {
 	MX6Q_PAD_EIM_BCLK__IPU1_DI1_PIN16	= IOMUX_PAD(0x046C, 0x0158, 1, 0x0000, 0, 0),
 	MX6Q_PAD_EIM_BCLK__GPIO_6_31		= IOMUX_PAD(0x046C, 0x0158, 5, 0x0000, 0, 0),
 	MX6Q_PAD_EIM_BCLK__TPSMP_HDATA_31	= IOMUX_PAD(0x046C, 0x0158, 6, 0x0000, 0, 0),
-	MX6Q_PAD_DI0_DISP_CLK__IPU1_DI0_DSP_CLK = IOMUX_PAD(0x0470, 0x015C, 0, 0x0000, 0, 0),
-	MX6Q_PAD_DI0_DISP_CLK__IPU2_DI0_DSP_CLK = IOMUX_PAD(0x0470, 0x015C, 1, 0x0000, 0, 0),
+	MX6Q_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK = IOMUX_PAD(0x0470, 0x015C, 0, 0x0000, 0, 0),
+	MX6Q_PAD_DI0_DISP_CLK__IPU2_DI0_DISP_CLK = IOMUX_PAD(0x0470, 0x015C, 1, 0x0000, 0, 0),
 	MX6Q_PAD_DI0_DISP_CLK__MIPI_CR_DPY_OT28 = IOMUX_PAD(0x0470, 0x015C, 3, 0x0000, 0, 0),
 	MX6Q_PAD_DI0_DISP_CLK__SDMA_DBG_CR_STA0 = IOMUX_PAD(0x0470, 0x015C, 4, 0x0000, 0, 0),
 	MX6Q_PAD_DI0_DISP_CLK__GPIO_4_16	= IOMUX_PAD(0x0470, 0x015C, 5, 0x0000, 0, 0),
Signature · 1 line
1.7.0.4
#1 lore raw

PATCH 1/1 mx6: Make pad name macro consistent with the datasheet

Dear Ashok,

Quoted 4 lines

Use the same name as defined in the datasheet.
DSP_CLK -> DISP_CLK

Signed-off-by Ashok Kumar Reddy Kourla <[email protected]>
Acked-by Marek Vasut <[email protected]>

arch/arm/include/asm/arch-mx6/mx6x_pins.h enum { · line 530

Quoted 10 lines
---
 arch/arm/include/asm/arch-mx6/mx6x_pins.h |    4 ++--
 1 files changed, 2 insertions(+), 2 deletions(-)
(quoted diff) +0 -0

b/arch/arm/include/asm/arch-mx6/mx6x_pins.h index afaa068..377d97f 100644

arch/arm/include/asm/arch-mx6/mx6x_pins.h +0 -0
@@ -530,8 +530,8 @@ enum {
 	MX6Q_PAD_EIM_BCLK__IPU1_DI1_PIN16	= IOMUX_PAD(0x046C, 0x0158, 1,

0x0000,

Quoted 8 lines
arch/arm/include/asm/arch-mx6/mx6x_pins.h +0 -0
 0, 0), MX6Q_PAD_EIM_BCLK__GPIO_6_31		= IOMUX_PAD(0x046C, 0x0158, 5,
 0x0000, 0, 0), MX6Q_PAD_EIM_BCLK__TPSMP_HDATA_31	= IOMUX_PAD(0x046C,

0x0158, 6, 0x0000, 0, 0), - MX6Q_PAD_DI0_DISP_CLK__IPU1_DI0_DSP_CLK =
IOMUX_PAD(0x0470, 0x015C, 0, 0x0000, 0, 0),

arch/arm/include/asm/arch-mx6/mx6x_pins.h +0 -1
-	MX6Q_PAD_DI0_DISP_CLK__IPU2_DI0_DSP_CLK = IOMUX_PAD(0x0470, 0x015C, 1,

0x0000, 0, 0), + MX6Q_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK =
IOMUX_PAD(0x0470, 0x015C, 0, 0x0000, 0, 0),

arch/arm/include/asm/arch-mx6/mx6x_pins.h +1 -0
+	MX6Q_PAD_DI0_DISP_CLK__IPU2_DI0_DISP_CLK = IOMUX_PAD(0x0470, 0x015C, 1,
Quoted 4 lines

0x0000, 0, 0), MX6Q_PAD_DI0_DISP_CLK__MIPI_CR_DPY_OT28 = IOMUX_PAD(0x0470, 0x015C, 3, 0x0000, 0, 0), MX6Q_PAD_DI0_DISP_CLK__SDMA_DBG_CR_STA0 = IOMUX_PAD(0x0470, 0x015C, 4, 0x0000, 0, 0),
MX6Q_PAD_DI0_DISP_CLK__GPIO_4_16 = IOMUX_PAD(0x0470, 0x015C, 5, 0x0000,

0,

Quoted 1 line

0),

Best regards,
Marek Vasut

#2 lore raw

PATCH 1/1 mx6: Make pad name macro consistent with the datasheet

In reply to Ashok
Quoted 7 lines · Ashok

Use the same name as defined in the datasheet.
DSP_CLK -> DISP_CLK

Signed-off-by Ashok Kumar Reddy Kourla <[email protected]>

---

Applied to u-boot-imx, thanks.

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
#3 lore raw

PATCH 1/1 mx6: Make pad name macro consistent with the datasheet

Quoted 10 lines · Stefano Babic
Quoted 7 lines · Ashok

Use the same name as defined in the datasheet.
DSP_CLK -> DISP_CLK

Signed-off-by Ashok Kumar Reddy Kourla <[email protected]>

---

Applied to u-boot-imx, thanks.

Hmm, this isn't part of v2012.07-rc1? Sorry if I missed something.

Best regards

Dirk

#4 lore raw

PATCH 1/1 mx6: Make pad name macro consistent with the datasheet

Quoted 4 lines · Dirk Behme
Quoted 3 lines · Stefano Babic
Quoted 2 lines · Ashok

Hi Dirk,

Quoted 9 lines
Quoted 7 lines
Quoted 5 lines

Use the same name as defined in the datasheet.
DSP_CLK -> DISP_CLK

Signed-off-by Ashok Kumar Reddy Kourla <[email protected]>

---

Applied to u-boot-imx, thanks.

Hmm, this isn't part of v2012.07-rc1? Sorry if I missed something.

It is not, I applied it after -rc1.

Cheers,
Stefano

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================