tegra20: usb: rework set_host_mode
Subsystems (2)
PATCH 1/1 tegra20: usb: rework set_host_mode
This allows for two things:
- VBus GPIO may be used on other ports than the OTG one
- VBus GPIO may be low active if specified by DT
--- arch/arm/cpu/armv7/tegra20/usb.c | 35 +++++++++++++++++++----------------
1 Datei ge?ndert, 19 Zeilen hinzugef?gt(+), 16 Zeilen entfernt(-)
arch/arm/cpu/armv7/tegra20/usb.c +19 -16
@@ -137,24 +137,27 @@ static const u8 utmip_elastic_limit = 16;/* UTMIP High Speed Sync Start Delay */ static const u8 utmip_hs_sync_start_delay =9 ; -/* Put the port into host mode (this only works for OTG ports) */ +/* Put the port into host mode */ static void set_host_mode (struct fdt_usb *config) { -if (config->dr_mode ==DR_MODE_OTG ) { -/* Check whether remote host from USB1 is driving VBus */ -if (readl (&config->reg->phy_vbus_sensors) &VBUS_VLD_STS ) -return ; - -/* -* If not driving, we set the GPIO to enable VBUS. We assume -* that the pinmux is set up correctly for this. -*/ -if (fdt_gpio_isvalid (&config->vbus_gpio)) { -fdtdec_setup_gpio (&config->vbus_gpio); -gpio_direction_output (config->vbus_gpio.gpio,1 ); -debug ("set_host_mode: GPIO %d high\n" , - config->vbus_gpio.gpio); - } +/* +* If we are an OTG port, check if remote host is driving VBus and +* bail out in this case. +*/ +if (config->dr_mode ==DR_MODE_OTG && + (readl (&config->reg->phy_vbus_sensors) &VBUS_VLD_STS )) +return ; + +/* +* If not driving, we set the GPIO to enable VBUS. We assume +* that the pinmux is set up correctly for this. +*/ +if (fdt_gpio_isvalid (&config->vbus_gpio)) { +fdtdec_setup_gpio (&config->vbus_gpio); +gpio_direction_output (config->vbus_gpio.gpio, + (config->vbus_gpio.flags &FDT_GPIO_ACTIVE_LOW ) ?0 :1 ); +debug ("set_host_mode: GPIO %d %s\n" , config->vbus_gpio.gpio, + (config->vbus_gpio.flags &FDT_GPIO_ACTIVE_LOW ) ?"low" :"high" ); } }
Signature · 1 line
1.7.11.2
PATCH 1/1 tegra20: usb: rework set_host_mode
Quoted 3 lines · Lucas Stach
This allows for two things:
- VBus GPIO may be used on other ports than the OTG one
- VBus GPIO may be low active if specified by DT
Hmmm. Why would the board have control over whether VBUS is asserted if the port isn't intended to operate in OTG mode?
Perhaps power-saving? In that case, I wonder if representing this as a regulator rather than as a VBUS GPIO would make more sense?
But irrespective of those questions, I'm inclined to think the patch is probably OK.
PATCH 1/1 tegra20: usb: rework set_host_mode
Am Dienstag, den 07.08.2012, 14:21 -0600 schrieb Stephen Warren:
Quoted 5 lines · Lucas Stach
Quoted 3 lines
This allows for two things:
- VBus GPIO may be used on other ports than the OTG one
- VBus GPIO may be low active if specified by DT
Quoted 9 lines
Hmmm. Why would the board have control over whether VBUS is asserted if the port isn't intended to operate in OTG mode?
Perhaps power-saving? In that case, I wonder if representing this as a regulator rather than as a VBUS GPIO would make more sense?
But irrespective of those questions, I'm inclined to think the patch is probably OK.
On Colibri the second USB Port is powered down by default and only powered up if we are really going to use it. And the GPIO does exactly what it tells you from it's name: turn on VBus by triggering the USB power switch.
Thinking about a regulator for this in U-Boot is a bit of an overkill, for the Linux kernel this might be another story.
PATCH 1/1 tegra20: usb: rework set_host_mode
Quoted 12 lines · Lucas Stach
Am Dienstag, den 07.08.2012, 14:21 -0600 schrieb Stephen Warren:
Quoted 11 lines · Lucas Stach
Quoted 3 lines
This allows for two things:
- VBus GPIO may be used on other ports than the OTG one
- VBus GPIO may be low active if specified by DTHmmm. Why would the board have control over whether VBUS is asserted if the port isn't intended to operate in OTG mode?
Perhaps power-saving? In that case, I wonder if representing this as a regulator rather than as a VBUS GPIO would make more sense?
Quoted 7 lines
Quoted 3 lines
But irrespective of those questions, I'm inclined to think the patch is probably OK.
On Colibri the second USB Port is powered down by default and only powered up if we are really going to use it. And the GPIO does exactly what it tells you from it's name: turn on VBus by triggering the USB power switch.
It's probably fine to do this; the kernel also unconditionally sets up the VBUS GPIO irrespective of USB port mode.
Quoted 2 lines
Thinking about a regulator for this in U-Boot is a bit of an overkill, for the Linux kernel this might be another story.
Device tree content isn't supposed to be influence by the consumer; it should be identical irrespective of which bootloader/OS/... is using it.
So, in the future I expect this to be reworked to get rid of the vbus-gpio property and replace it with a regulator.