nat not working as expected
Hello,
I have a problem I am trying to solve and nat doesn't seem to be working. I have a set of ip addresses I don't want to go thru my transparent proxy so I have the following:
Chain PREROUTING (policy ACCEPT 1413 packets, 206K bytes)
pkts bytes target prot opt in out source
destination
0 0 ACCEPT tcp -- eth0 * 10.254.150.0/24
10.0.0.0/8 tcp dpt:80
...
0 0 ACCEPT tcp -- eth0 * 10.254.150.0/24
8.15.7.123 tcp dpt:80
2 120 ACCEPT tcp -- eth0 * 10.254.150.0/24
216.16.243.121 tcp dpt:80
0 0 ACCEPT tcp -- eth0 * 10.254.150.0/24
216.16.242.222 tcp dpt:80
...
0 0 ACCEPT tcp -- eth0 * 10.254.150.0/24
216.171.106.210 tcp dpt:80
0 0 DNAT tcp -- eth0 * 10.254.150.0/24 0.0.0.0/0 tcp dpt:80 to:10.254.150.1:8080
Chain POSTROUTING (policy ACCEPT 922 packets, 81534 bytes)
pkts bytes target prot opt in out source
destination
0 0 ACCEPT all -- * eth1 10.254.150.0/24
10.0.0.0/8
0 0 ACCEPT all -- * eth1 10.254.150.0/24
172.16.0.0/12
0 0 ACCEPT all -- * eth1 10.254.150.0/24
192.168.0.0/16
0 0 SNAT all -- * eth1 10.254.150.0/24 0.0.0.0/0 to:xxx.xxx.149.209
My packet hits the pre-routing chain and is accepted but then seems to get lost, it doesn't get natted and go out my external interface.
tcpdump on internal interface:
13:33:03.157163 IP 10.254.150.91.53169 > 216.16.243.121.http: Flags [S], seq 1127713574, win 5840, options [mss 1460,sackOK,TS val 2344806144 ecr 0,nop,wscale 6], length 0
nothing shows on external interface:
The routing looks correct.
$ ip r g 216.16.243.121 216.16.243.121 via xxx.xxx.149.1 dev eth1 src xxx.xxx.149.209
What am I missing?
Thanks for your indulgence,
Steve
Sorry for the noise - I had some routes set in an alternative routeing table that was routing out a gre over a vpn.
Quoted 60 lines · Stephen Clark
Hello,
I have a problem I am trying to solve and nat doesn't seem to be working. I have a set of ip addresses I don't want to go thru my transparent proxy so I have the following:
Chain PREROUTING (policy ACCEPT 1413 packets, 206K bytes)
pkts bytes target prot opt in out source
destination0 0 ACCEPT tcp -- eth0 * 10.254.150.0/24 10.0.0.0/8 tcp dpt:80 ... 0 0 ACCEPT tcp -- eth0 * 10.254.150.0/24 8.15.7.123 tcp dpt:80 2 120 ACCEPT tcp -- eth0 * 10.254.150.0/24 216.16.243.121 tcp dpt:80 0 0 ACCEPT tcp -- eth0 * 10.254.150.0/24 216.16.242.222 tcp dpt:80 ... 0 0 ACCEPT tcp -- eth0 * 10.254.150.0/24 216.171.106.210 tcp dpt:80 0 0 DNAT tcp -- eth0 * 10.254.150.0/240.0.0.0/0 tcp dpt:80 to:10.254.150.1:8080
Chain POSTROUTING (policy ACCEPT 922 packets, 81534 bytes)
pkts bytes target prot opt in out source
destination0 0 ACCEPT all -- * eth1 10.254.150.0/24 10.0.0.0/8 0 0 ACCEPT all -- * eth1 10.254.150.0/24 172.16.0.0/12 0 0 ACCEPT all -- * eth1 10.254.150.0/24 192.168.0.0/16 0 0 SNAT all -- * eth1 10.254.150.0/240.0.0.0/0 to:xxx.xxx.149.209
My packet hits the pre-routing chain and is accepted but then seems to get lost, it doesn't get natted and go out my external interface.
tcpdump on internal interface:
13:33:03.157163 IP 10.254.150.91.53169 > 216.16.243.121.http: Flags [S], seq 1127713574, win 5840, options [mss 1460,sackOK,TS val 2344806144 ecr 0,nop,wscale 6], length 0nothing shows on external interface:
The routing looks correct.
$ ip r g 216.16.243.121 216.16.243.121 via xxx.xxx.149.1 dev eth1 src xxx.xxx.149.209What am I missing?
Thanks for your indulgence,
SteveSignature · 3 lines
To unsubscribe from this list: send the line "unsubscribe netfilter-devel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Signature · 5 lines
"They that give up essential liberty to obtain temporary safety, deserve neither liberty nor safety." (Ben Franklin) "The course of history shows that as a government grows, liberty decreases." (Thomas Jefferson)