leds-pwm: First setting of brightness does nothing
Subsystems (7)
A message that is not in the archive (sent off-list or not yet received): [email protected]
Hi all,
I have found a bug using leds-pwm with the i.MX PWM driver. The first time a non-0 brightness is set through sysfs, this has no effect. It works fine from the 2nd time.
The cause of this bug is that leds-pwm.c:led_pwm_set() calls pwm_config() before pwm_enable(), while in the i.MX PWM driver pwm_enable() enables the PWM IP clock, so that a call to pwm_config() has no effect before the first call to pwm_enable().
Several other PWM drivers in drivers/pwm/ work in the same way. pwm-beeper.c and pwm_bl.c also call pwm_config() before pwm_enable(). The PWM documentation does not say if the wrong doers are these PWM users or the i.MX-like PWM drivers.
So what should be fixed? Fixing these PWM users would be quite easy since it's a simple swap of the pwm_config() and pwm_enable() calls. This should not produce any glitch since the duty cycle is always set to 0 by these PWM users before calling pwm_disable().
Best regards,
Beno?t
PATCH 1/1 pwm: Call pwm_enable() before pwm_config()
Some PWM drivers enable the clock of the PWM peripheral in pwm_enable(). Hence, for these drivers, a call to pwm_config() does not have any effect before pwm_enable() has been called.
This patch fixes the PWM users to make sure that they call pwm_enable() before pwm_config().
This fixes the first setting of brightness through sysfs that had no effect with leds-pwm and the i.MX PWM driver.
--- .../drivers/input/misc/pwm-beeper.c | 6 +++--- .../drivers/leds/leds-pwm.c | 2 +- .../drivers/video/backlight/pwm_bl.c | 2 +- 3 files changed, 5 insertions(+), 5 deletions(-)
drivers/input/misc/pwm-beeper.c +3 -3
@@ -53,10 +53,10 @@ static int pwm_beeper_event(struct input_dev *input,pwm_disable (beeper->pwm); }else { period =HZ_TO_NANOSECONDS (value); - ret =pwm_config (beeper->pwm, period /2 , period); + ret =pwm_enable (beeper->pwm);if (ret)return ret; - ret =pwm_enable (beeper->pwm); + ret =pwm_config (beeper->pwm, period /2 , period);if (ret)return ret; beeper->period = period;
@@ -156,8 +156,8 @@ static int pwm_beeper_resume(struct device *dev)struct pwm_beeper *beeper =dev_get_drvdata (dev);if (beeper->period) { -pwm_config (beeper->pwm, beeper->period /2 , beeper->period);pwm_enable (beeper->pwm); +pwm_config (beeper->pwm, beeper->period /2 , beeper->period); }return 0 ;
drivers/leds/leds-pwm.c +1 -1
@@ -42,8 +42,8 @@ static void led_pwm_set(struct led_classdev *led_cdev,pwm_config (led_dat->pwm,0 , period);pwm_disable (led_dat->pwm); }else { -pwm_config (led_dat->pwm, brightness * period / max, period);pwm_enable (led_dat->pwm); +pwm_config (led_dat->pwm, brightness * period / max, period); } }
drivers/video/backlight/pwm_bl.c +1 -1
@@ -65,8 +65,8 @@ static int pwm_backlight_update_status(struct backlight_device *bl) duty_cycle = pb->lth_brightness + (duty_cycle * (pb->period - pb->lth_brightness) / max); -pwm_config (pb->pwm, duty_cycle, pb->period);pwm_enable (pb->pwm); +pwm_config (pb->pwm, duty_cycle, pb->period); }if (pb->notify_after)
Re: [PATCH] pwm: Call pwm_enable() before pwm_config()
Quoted 9 lines · Beno?t Th?baudeau
Some PWM drivers enable the clock of the PWM peripheral in
pwm_enable(). Hence, for these drivers, a call topwm_config()does not have any effect beforepwm_enable()has been called.This patch fixes the PWM users to make sure that they call
pwm_enable()beforepwm_config().This fixes the first setting of brightness through sysfs that had no effect with leds-pwm and the i.MX PWM driver.
But isn't this a bug in the PWM peripheral driver? With this change the PWM will start with the old settings first. While this is not so much of a problem for a backlight (although it might cause a short flickering) it might cause problems for other applications, like using the PWM pin as a timing generator. In my opinion it's better to fix the PWM peripheral drivers which have this problem instead of trying to work around it in every user of the PWM API.
- Lars
Re: [PATCH] pwm: Call pwm_enable() before pwm_config()
Quoted 15 lines · Lars-Peter Clausen
Quoted 6 lines · Benoît Thébaudeau
Some PWM drivers enable the clock of the PWM peripheral in
pwm_enable(). Hence,
for these drivers, a call topwm_config()does not have any effect beforepwm_enable()has been called.Quoted 7 lines
This patch fixes the PWM users to make sure that they call
pwm_enable()beforepwm_config().This fixes the first setting of brightness through sysfs that had no effect with
leds-pwm and the i.MX PWM driver.
Quoted 12 lines
But isn't this a bug in the PWM peripheral driver? With this change the PWM
will start with the old settings first. While this is not so much of a problem
for a backlight (although it might cause a short flickering) it might cause
problems for other applications, like using the PWM pin as a timing generator.
In my opinion it's better to fix the PWM peripheral drivers which have this
problem instead of trying to work around it in every user of the PWM API.
I don't know. See my detailed description of this issue here:
http://lists.infradead.org/pipermail/linux-arm-kernel/2012-August/115667.html
Where the bug is depends on the detailed definition of the PWM API, which I don't find documented anywhere.
If pwm_enable() means "start PWM timer with the configured settings", then the bug is in the drivers. If it means "enable the PWM peripheral so that we can work with it", then the bug is in the PWM users.
I don't really have time to work on this, so I suggested this patch as a simple solution. Otherwise, it means reworking several PWM drivers for different hardware that is not available to everyone for testing.
If we decide to only change the i.MX PWM driver, the fix would be:pwm_config()
{
save passed config in private data;
if (pwm enabled)
apply passed config;
}pwm_enable()
{
if (!(pwm enabled)) {
enable pwm ip clk;
apply config from private data;
}
}If we fix only this driver, we must not forget that the same issue probably exists with several other PWM drivers.
As I said in my bug description, the PWM users set the duty cycle to 0 before calling pwm_disable(), so fixing the PWM users should not be an issue, even in the timing generator use case you're talking about.
I don't have a strong opinion about what should be fixed here.
Best regards,
Benoît
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH] pwm: Call pwm_enable() before pwm_config()
Quoted 32 lines · Beno?t Th?baudeau
Quoted 15 lines · Lars-Peter Clausen
Quoted 6 lines · Beno?t Th?baudeau
Some PWM drivers enable the clock of the PWM peripheral in
pwm_enable(). Hence,
for these drivers, a call topwm_config()does not have any effect beforepwm_enable()has been called.Quoted 7 lines
This patch fixes the PWM users to make sure that they call
pwm_enable()beforepwm_config().This fixes the first setting of brightness through sysfs that had no effect with
leds-pwm and the i.MX PWM driver.Quoted 12 lines
But isn't this a bug in the PWM peripheral driver? With this change the PWM
will start with the old settings first. While this is not so much of a problem
for a backlight (although it might cause a short flickering) it might cause
problems for other applications, like using the PWM pin as a timing generator.
In my opinion it's better to fix the PWM peripheral drivers which have this
problem instead of trying to work around it in every user of the PWM API.I don't know. See my detailed description of this issue here:
http://lists.infradead.org/pipermail/linux-arm-kernel/2012-August/115667.html
Quoted 6 lines
Where the bug is depends on the detailed definition of the PWM API, which I don't find documented anywhere.
If
pwm_enable()means "start PWM timer with the configured settings", then the bug is in the drivers. If it means "enable the PWM peripheral so that we can work with it", then the bug is in the PWM users.
It really is the former. See the description of pwm_enable() in drivers/pwm/core.c
Quoted 13 lines
I don't really have time to work on this, so I suggested this patch as a simple solution. Otherwise, it means reworking several PWM drivers for different hardware that is not available to everyone for testing.
If we decide to only change the i.MX PWM driver, the fix would be:
pwm_config(){ save passed config in private data; if (pwm enabled) apply passed config; }
Quoted 7 lines
pwm_enable(){ if (!(pwm enabled)) { enable pwm ip clk; apply config from private data; } }
Another option is to enable the clock if it is disabled when the device is configured. E.g. that's what tegra does.
Quoted 4 lines
If we fix only this driver, we must not forget that the same issue probably exists with several other PWM drivers.
Since this seems to be a common pattern in a number of PWM drivers it might make sense to simply add support for enabling/disabling a clk to the pwm core. Or maybe just use the runtime pm API for this. This probably makes even more sense and grab a reference to the pm context when the enable() is called, release it when disable() is called and also grab it before calling the device's config callback and release it afterward.
- Lars
Re: [PATCH] pwm: Call pwm_enable() before pwm_config()
Quoted 5 lines · Lars-Peter Clausen
[...]
Or maybe just use the runtime pm API for this. This probably makes even more sense and grab a reference to the pm context when theenable()is called, release it whendisable()is called and also grab it before calling the device's config callback and release it afterward.
Btw. this seems to be exactly what the pwm-tiecap and pwm-tiehrpwm drivers already do today. I'd just make that a core PWM framework feature.
Re: [PATCH] pwm: Call pwm_enable() before pwm_config()
Quoted 9 lines · Lars-Peter Clausen
Quoted 5 lines · Lars-Peter Clausen
[...]
Or maybe just use the runtime pm API for this. This probably makes even more sense and grab a reference to the pm context when theenable()is called, release it whendisable()is called and also grab it before calling the device's config callback and release it afterward.Btw. this seems to be exactly what the pwm-tiecap and pwm-tiehrpwm drivers already do today. I'd just make that a core PWM framework feature.
Using runtime PM for this sounds indeed like the most generic approach. I'm not very familiar with the API, but I thought it required explicit architecture or bus support (or the driver itself can provide hooks via pm_ops), so it might be difficult to implement for platforms that don't have working runtime PM support. I'll have to look into this some more.
Anyway, if we add this kind of support to the PWM core we should take it through next first. For drivers that are currently broken, they should be, as you said, fixed by enabling the clock before reconfiguring and disable it after (unless the PWM is enabled) like Tegra does.
Thierry
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20120823/a1ac7c74/attachment.sig>
Re: [PATCH] pwm: Call pwm_enable() before pwm_config()
Quoted 5 lines · Thierry Reding
Using runtime PM for this sounds indeed like the most generic approach. I'm not very familiar with the API, but I thought it required explicit architecture or bus support (or the driver itself can provide hooks via
pm_ops), so it might be difficult to implement for platforms that don't have working runtime PM support. I'll have to look into this some more.
It doesn't require explicit arch support, though many architectures choose to integrate their PM frameworks with it either directly or via power domains. If the architecture doesn't do anything with it then it should just work at the driver level.
Re: [PATCH] pwm: Call pwm_enable() before pwm_config()
In reply to Lars-Peter ClausenQuoted 33 lines · Lars-Peter Clausen
Quoted 32 lines · Beno?t Th?baudeau
Quoted 15 lines · Lars-Peter Clausen
Quoted 6 lines · Beno?t Th?baudeau
Some PWM drivers enable the clock of the PWM peripheral in
pwm_enable(). Hence,
for these drivers, a call topwm_config()does not have any effect beforepwm_enable()has been called.Quoted 7 lines
This patch fixes the PWM users to make sure that they call
pwm_enable()beforepwm_config().This fixes the first setting of brightness through sysfs that had no effect with
leds-pwm and the i.MX PWM driver.Quoted 12 lines
But isn't this a bug in the PWM peripheral driver? With this change the PWM
will start with the old settings first. While this is not so much of a problem
for a backlight (although it might cause a short flickering) it might cause
problems for other applications, like using the PWM pin as a timing generator.
In my opinion it's better to fix the PWM peripheral drivers which have this
problem instead of trying to work around it in every user of the PWM API.I don't know. See my detailed description of this issue here:
http://lists.infradead.org/pipermail/linux-arm-kernel/2012-August/115667.html
Quoted 8 lines
Quoted 6 lines
Where the bug is depends on the detailed definition of the PWM API, which I don't find documented anywhere.
If
pwm_enable()means "start PWM timer with the configured settings", then the bug is in the drivers. If it means "enable the PWM peripheral so that we can work with it", then the bug is in the PWM users.It really is the former. See the description of
pwm_enable()indrivers/pwm/core.c
Yes. pwm_enable() is only for starting the PWM and *not* the peripheral. I should update the documentation to make this clearer.
Quoted 20 lines
Quoted 12 lines
I don't really have time to work on this, so I suggested this patch as a simple solution. Otherwise, it means reworking several PWM drivers for different hardware that is not available to everyone for testing.
If we decide to only change the i.MX PWM driver, the fix would be:
pwm_config(){ save passed config in private data; if (pwm enabled) apply passed config; }Quoted 7 lines
pwm_enable(){ if (!(pwm enabled)) { enable pwm ip clk; apply config from private data; } }
Quoted 2 lines
Another option is to enable the clock if it is disabled when the device is configured. E.g. that's what tegra does.
Yes, that would have been my proposal as well.
Quoted 9 lines
Quoted 2 lines
If we fix only this driver, we must not forget that the same issue probably exists with several other PWM drivers.
Since this seems to be a common pattern in a number of PWM drivers it might make sense to simply add support for enabling/disabling a clk to the pwm core. Or maybe just use the runtime pm API for this. This probably makes even more sense and grab a reference to the pm context when the
enable()is called, release it whendisable()is called and also grab it before calling the device's config callback and release it afterward.
The problem with adding this kind of support in the core is that the device or platform doesn't necessarily support runtime PM. Perhaps adding a flag to mark compatible drivers would be an option. If the runtime PM API gracefully handles cases where no callbacks are implemented (and therefore assumed unneeded) things should also work.
On the other hand this really is very driver-specific stuff. A lot of hardware doesn't require an explicit clock being enabled to write registers so those wouldn't need the implicit PM calls either.
Thierry
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20120823/c9e9b436/attachment.sig>
PATCH 1/1 pwm-imx: Fix config / enable / disable
imx_pwm_config() did not enable the PWM IP clock while accessing the registers. Hence, a call to pwm_config() had no effect before pwm_enable() had been called, which does not comply to the PWM API.
Moreover, calling pwm_disable() then pwm_enable() must be a transparent operation.
This fixes the first setting of brightness through sysfs that had no effect with leds-pwm.
--- .../drivers/pwm/pwm-imx.c | 55 +++++++++++++++----- 1 file changed, 43 insertions(+), 12 deletions(-)
drivers/pwm/pwm-imx.c +43 -12
@@ -55,6 +55,16 @@ static int imx_pwm_config(struct pwm_chip *chip, {struct imx_chip *imx =to_imx_chip (chip); +/* +* If the PWM is disabled, make sure to turn on the clock before +* accessing the registers. +*/ +if (!imx->clk_enabled) { +int rc =clk_prepare_enable (imx->clk); +if (rc) +return rc; + } +if (!(cpu_is_mx1 () ||cpu_is_mx21 ())) {unsigned long long c;unsigned long period_cycles, duty_cycles, prescale;
@@ -85,8 +95,11 @@ static int imx_pwm_config(struct pwm_chip *chip,writel (period_cycles, imx->mmio_base +MX3_PWMPR ); cr =MX3_PWMCR_PRESCALER (prescale) | -MX3_PWMCR_DOZEEN |MX3_PWMCR_WAITEN | -MX3_PWMCR_DBGEN |MX3_PWMCR_EN ; +MX3_PWMCR_DOZEEN |MX3_PWMCR_WAITEN |MX3_PWMCR_DBGEN ; + +/* If the PWM is enabled, keep it so. */ +if (imx->clk_enabled) + cr |=MX3_PWMCR_EN ;if (cpu_is_mx25 ()) cr |=MX3_PWMCR_CLKSRC_IPG ;
@@ -118,32 +131,50 @@ static int imx_pwm_config(struct pwm_chip *chip,BUG (); } +/* If the PWM is disabled, turn the clock off again to save power. */ +if (!imx->clk_enabled) +clk_disable_unprepare (imx->clk); +return 0 ; }static int imx_pwm_enable (struct pwm_chip *chip,struct pwm_device *pwm) {struct imx_chip *imx =to_imx_chip (chip); -int rc =0 ; +int rc; -if (!imx->clk_enabled) { - rc =clk_prepare_enable (imx->clk); -if (!rc) - imx->clk_enabled =1 ; +if (imx->clk_enabled) +return 0 ; + + rc =clk_prepare_enable (imx->clk); +if (rc) +return rc; + +if (!(cpu_is_mx1 () ||cpu_is_mx21 ())) { +u32 cr =readl (imx->mmio_base +MX3_PWMCR ); + cr |=MX3_PWMCR_EN ; +writel (cr, imx->mmio_base +MX3_PWMCR ); } -return rc; + + imx->clk_enabled =1 ; +return 0 ; }static void imx_pwm_disable (struct pwm_chip *chip,struct pwm_device *pwm) {struct imx_chip *imx =to_imx_chip (chip); -writel (0 , imx->mmio_base +MX3_PWMCR ); +if (!imx->clk_enabled) +return ; -if (imx->clk_enabled) { -clk_disable_unprepare (imx->clk); - imx->clk_enabled =0 ; +if (!(cpu_is_mx1 () ||cpu_is_mx21 ())) { +u32 cr =readl (imx->mmio_base +MX3_PWMCR ); + cr &= ~MX3_PWMCR_EN ; +writel (cr, imx->mmio_base +MX3_PWMCR ); } + +clk_disable_unprepare (imx->clk); + imx->clk_enabled =0 ; }static struct pwm_ops imx_pwm_ops = {
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Sascha Hauer
maintainerRe: [PATCH] pwm-imx: Fix config / enable / disable
Quoted 9 lines · Beno?t Th?baudeau
imx_pwm_config()did not enable the PWM IP clock while accessing the registers. Hence, a call topwm_config()had no effect beforepwm_enable()had been called, which does not comply to the PWM API.Moreover, calling
pwm_disable()thenpwm_enable()must be a transparent operation.This fixes the first setting of brightness through sysfs that had no effect with leds-pwm.
I don't really like this patch. I'd like to have this one first, it makes further cleanups easier:
https://lkml.org/lkml/2012/8/28/24
Simililarly, we should probably introduce a imx_pwm_[en|dis]able_v[12]
Then, the pwm core already makes sure that pwm_enable/disable are called only once, so the if (imx->clk_enabled) in pwm_enable/disable is unnecessary.
Sascha
Quoted 112 lines
Cc Thierry Reding <[email protected]>Cc <[email protected]>Cc Sascha Hauer <[email protected]>Cc <[email protected]>Cc Beno?t Th?baudeau <[email protected]>Signed-off-by Beno?t Th?baudeau <[email protected]>--- .../drivers/pwm/pwm-imx.c | 55 +++++++++++++++----- 1 file changed, 43 insertions(+), 12 deletions(-)drivers/pwm/pwm-imx.c +43
-13@@ -55,6 +55,16 @@ static int imx_pwm_config(struct pwm_chip *chip, {struct imx_chip *imx =to_imx_chip (chip); +/* +* If the PWM is disabled, make sure to turn on the clock before +* accessing the registers. +*/ +if (!imx->clk_enabled) { +int rc =clk_prepare_enable (imx->clk); +if (rc) +return rc; + } +if (!(cpu_is_mx1 () ||cpu_is_mx21 ())) {unsigned long long c;unsigned long period_cycles, duty_cycles, prescale;@@ -85,8 +95,11 @@ static int imx_pwm_config(struct pwm_chip *chip,writel (period_cycles, imx->mmio_base +MX3_PWMPR ); cr =MX3_PWMCR_PRESCALER (prescale) | -MX3_PWMCR_DOZEEN |MX3_PWMCR_WAITEN | -MX3_PWMCR_DBGEN |MX3_PWMCR_EN ; +MX3_PWMCR_DOZEEN |MX3_PWMCR_WAITEN |MX3_PWMCR_DBGEN ; + +/* If the PWM is enabled, keep it so. */ +if (imx->clk_enabled) + cr |=MX3_PWMCR_EN ;if (cpu_is_mx25 ()) cr |=MX3_PWMCR_CLKSRC_IPG ;@@ -118,32 +131,50 @@ static int imx_pwm_config(struct pwm_chip *chip,BUG (); } +/* If the PWM is disabled, turn the clock off again to save power. */ +if (!imx->clk_enabled) +clk_disable_unprepare (imx->clk); +return 0 ; }static int imx_pwm_enable (struct pwm_chip *chip,struct pwm_device *pwm) {struct imx_chip *imx =to_imx_chip (chip); -int rc =0 ; +int rc; -if (!imx->clk_enabled) { - rc =clk_prepare_enable (imx->clk); -if (!rc) - imx->clk_enabled =1 ; +if (imx->clk_enabled) +return 0 ; + + rc =clk_prepare_enable (imx->clk); +if (rc) +return rc; + +if (!(cpu_is_mx1 () ||cpu_is_mx21 ())) { +u32 cr =readl (imx->mmio_base +MX3_PWMCR ); + cr |=MX3_PWMCR_EN ; +writel (cr, imx->mmio_base +MX3_PWMCR ); } -return rc; + + imx->clk_enabled =1 ; +return 0 ; }static void imx_pwm_disable (struct pwm_chip *chip,struct pwm_device *pwm) {struct imx_chip *imx =to_imx_chip (chip); -writel (0 , imx->mmio_base +MX3_PWMCR ); +if (!imx->clk_enabled) +return ; -if (imx->clk_enabled) { -clk_disable_unprepare (imx->clk); - imx->clk_enabled =0 ; +if (!(cpu_is_mx1 () ||cpu_is_mx21 ())) { +u32 cr =readl (imx->mmio_base +MX3_PWMCR ); + cr &= ~MX3_PWMCR_EN ; +writel (cr, imx->mmio_base +MX3_PWMCR ); } + +clk_disable_unprepare (imx->clk); + imx->clk_enabled =0 ; }static struct pwm_ops imx_pwm_ops = { --To unsubscribe from this list: send the line "unsubscribe linux-fbdev" in the body of a message to majordomo at vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signature · 4 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Re: [PATCH] pwm: Call pwm_enable() before pwm_config()
In reply to Lars-Peter ClausenQuoted 10 lines · Lars-Peter Clausen
Quoted 1 line · Beno??t Th??baudeau
exists with several other PWM drivers.
Since this seems to be a common pattern in a number of PWM drivers it might make sense to simply add support for enabling/disabling a clk to the pwm core. Or maybe just use the runtime pm API for this. This probably makes even more sense and grab a reference to the pm context when the
enable()is called, release it whendisable()is called and also grab it before calling the device's config callback and release it afterward.
It's a problem with IPs in general, a good proportion of modern SoCs need a clock supplying in order to interact with the registers on most of their IPs. runtime PM is the normal way forwards, Tegra recently started using regmap's cache code to handle this transparently in the driver.
Re: [PATCH] pwm: Call pwm_enable() before pwm_config()
In reply to Lars-Peter ClausenQuoted 12 lines · Lars-Peter Clausen
Quoted 9 lines · Beno?t Th?baudeau
Some PWM drivers enable the clock of the PWM peripheral in
pwm_enable(). Hence, for these drivers, a call topwm_config()does not have any effect beforepwm_enable()has been called.This patch fixes the PWM users to make sure that they call
pwm_enable()beforepwm_config().This fixes the first setting of brightness through sysfs that had no effect with leds-pwm and the i.MX PWM driver.
Quoted 6 lines
But isn't this a bug in the PWM peripheral driver? With this change the PWM will start with the old settings first. While this is not so much of a problem for a backlight (although it might cause a short flickering) it might cause problems for other applications, like using the PWM pin as a timing generator. In my opinion it's better to fix the PWM peripheral drivers which have this problem instead of trying to work around it in every user of the PWM API.
Hi Lars-Peter Clausen,
I think so.
It would be better to fix the PWM peripheral drivers.
Best regards,
Jingoo Han
Quoted 6 lines
- Lars
--
To unsubscribe from this list: send the line "unsubscribe linux-fbdev" in the body of a message to majordomo at vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html