Skip to contentSkip to conversation

atmel_nand: fix the U-Boot output information about nand flash with PMECC enable.

PATCH New Josh Wu 2 participants 2 messages Sep 10, 2012 – Sep 13, 2012

Subsystems (3)
Memory technology devices (MTD) Arm/Microchip (AT91) SoC support NAND flash
lore
Share & tools
lore

Josh Wu

author
#0 lore raw

PATCH 1/1 atmel_nand: fix the U-Boot output information about nand flash with PMECC enable.

Before the patch, it looks like:

	|U-Boot 2012.07-00441-gd578d6f-dirty (Sep 10 2012 - 16:11:06)
	|
	|CPU: AT91SAM9G35
	|Crystal frequency:       12 MHz
	|CPU clock        :      400 MHz
	|Master clock     :  133.333 MHz
	|DRAM:  128 MiB
	|WARNING: Caches not enabled
Quoted 2 lines
	|NAND:  Initialize PMECC params, cap: 2, sector: 512
	|256 MiB
	|MMC:   mci: 0
	|In:    serial
	|Out:   serial
	|Err:   serial
	|Net:   macb0
	|Hit any key to stop autoboot:  0

After the patch:

	|U-Boot 2012.07-00441-gd578d6f-dirty (Sep 10 2012 - 16:18:11)
	|
	|CPU: AT91SAM9G35
	|Crystal frequency:       12 MHz
	|CPU clock        :      400 MHz
	|Master clock     :  133.333 MHz
	|DRAM:  128 MiB
	|WARNING: Caches not enabled
Quoted 1 line
	|NAND:  256 MiB
	|	... ...
	|Hit any key to stop autoboot:  0
Signed-off-by Josh Wu <[email protected]>
---
 drivers/mtd/nand/atmel_nand.c |    5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/mtd/nand/atmel_nand.c +3 -2
index c6aa5db..994dd9f 100644
@@ -652,8 +652,9 @@ static int atmel_pmecc_nand_init_params(struct nand_chip *nand,
 	sector_size = host->pmecc_sector_size = CONFIG_PMECC_SECTOR_SIZE;
 	host->pmecc_index_table_offset = CONFIG_PMECC_INDEX_TABLE_OFFSET;
 
-	printk(KERN_INFO "Initialize PMECC params, cap: %d, sector: %d\n",
-		 cap, sector_size);
+	MTDDEBUG(MTD_DEBUG_LEVEL1,
+		"Initialize PMECC params, cap: %d, sector: %d\n",
+		cap, sector_size);
 
 	host->pmecc = (struct pmecc_regs __iomem *) ATMEL_BASE_PMECC;
 	host->pmerrloc = (struct pmecc_errloc_regs __iomem *)
Signature · 1 line
1.7.9.5
#1 lore raw

PATCH 1/1 atmel_nand: fix the U-Boot output information about nand flash with PMECC enable.

Dear Josh Wu,

Quoted 27 lines · Josh Wu

Before the patch, it looks like:

	|U-Boot 2012.07-00441-gd578d6f-dirty (Sep 10 2012 - 16:11:06)
	|
	|CPU: AT91SAM9G35
	|Crystal frequency:       12 MHz
	|CPU clock        :      400 MHz
	|Master clock     :  133.333 MHz
	|DRAM:  128 MiB
	|WARNING: Caches not enabled
Quoted 2 lines
	|NAND:  Initialize PMECC params, cap: 2, sector: 512
	|256 MiB
	|MMC:   mci: 0
	|In:    serial
	|Out:   serial
	|Err:   serial
	|Net:   macb0
	|Hit any key to stop autoboot:  0

After the patch:

	|U-Boot 2012.07-00441-gd578d6f-dirty (Sep 10 2012 - 16:18:11)
	|
	|CPU: AT91SAM9G35
	|Crystal frequency:       12 MHz
	|CPU clock        :      400 MHz
	|Master clock     :  133.333 MHz
	|DRAM:  128 MiB
	|WARNING: Caches not enabled
Quoted 6 lines
Quoted 1 line
	|NAND:  256 MiB
	|	... ...
	|Hit any key to stop autoboot:  0
Signed-off-by Josh Wu <[email protected]>

---

applied to u-boot-atmel/master, thanks!

Best regards

Andreas Bie?mann