tda8290 regression fix

Hi,

Ever since 2.6.26 or so (where there was a code reorg) I had to carry this patch. Without it the received signal is noisy, and the card worked fine prior to the code reorg. This patch is a hack, mostly as a result of my inability to follow the code paths (and bisect failing). I'd be more than willing to test whatever the proper patch might be prior to any mainlining.

Thanks,
/Anders

$ cat /TV_CARD.diff

index 064d14c..498cc7b 100644
@@ -635,7 +635,11 @@ static int tda829x_find_tuner(struct dvb_frontend *fe)
 
                dvb_attach(tda827x_attach, fe, priv->tda827x_addr,
                           priv->i2c_props.adap, &priv->cfg);
+               tuner_info("ANDERS: setting switch_addr. was 0x%02x, new 0x%02x\n",priv->cfg.switch_addr,priv->i2c_props.addr);
                priv->cfg.switch_addr = priv->i2c_props.addr;
+               priv->cfg.switch_addr = 0xc2 / 2;
+               tuner_info("ANDERS: new 0x%02x\n",priv->cfg.switch_addr);
+
        }
        if (fe->ops.tuner_ops.init)
                fe->ops.tuner_ops.init(fe);

Em Thu, 30 Aug 2012 13:27:21 +0200
Anders Thomson <[email protected]> escreveu:

Regards,
Mauro

lspci -vv:
03:06.0 Multimedia controller: Philips Semiconductors SAA7131/SAA7133/SAA7135 Video Broadcast Decoder (rev d1)
Subsystem: Pinnacle Systems Inc. Device 002f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium

Latency: 64 (21000ns min, 8000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fdeff000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Kernel driver in use: saa7134
Kernel modules: saa7134

Without the patch I get a layer of noise added. Kind of like a weak aerial signal to an old analogue TV set.

-Anders

...and here's the modules I'm using

Module                  Size  Used by
hid_sunplus             1321  0
usbhid                 29765  0
uinput                  6426  2
saa7134_alsa            9359  0
tda1004x               12639  1
saa7134_dvb            22092  0
videobuf_dvb            4106  1 saa7134_dvb
dvb_core               78773  1 videobuf_dvb
ir_kbd_i2c              4473  0
tda827x                 8291  2
tda8290                11906  1
tuner                  13649  1
uvcvideo               54515  0
videobuf2_core         15467  1 uvcvideo
snd_hda_codec_realtek    46581  1
saa7134               149350  2 saa7134_alsa,saa7134_dvb
videobuf_dma_sg         6504  3 saa7134_alsa,saa7134_dvb,saa7134
videobuf_core          12866  3 videobuf_dvb,saa7134,videobuf_dma_sg
snd_hda_intel          20144  1
snd_hda_codec          59409  2 snd_hda_codec_realtek,snd_hda_intel
v4l2_common             4558  2 tuner,saa7134
videodev               68383  4 tuner,uvcvideo,saa7134,v4l2_common
snd_usb_audio          81087  0
lirc_dev                9954  0
ir_mce_kbd_decoder      2838  0
parport_pc             27310  0
rc_imon_mce             1349  0
v4l2_compat_ioctl32     6796  1 videodev
ir_rc6_decoder          1946  0
videobuf2_vmalloc       1812  1 uvcvideo
snd_usbmidi_lib        15516  1 snd_usb_audio
tveeprom               12721  1 saa7134
snd_hwdep               5006  2 snd_hda_codec,snd_usb_audio
asus_atk0110            7054  0
parport                24807  1 parport_pc
i2c_piix4               7680  0
videobuf2_memops        1638  1 videobuf2_vmalloc
ir_rc5_decoder          1433  0
imon                   18432  1
rc_core                10749  8 ir_kbd_i2c,saa7134,ir_mce_kbd_decoder,rc_imon_mce,ir_rc6_decoder,ir_rc5_decoder,imon
pcspkr                  1659  0
atiixp                  2404  0
rtc_cmos                7570  0
sg                     20980  0
snd_rawmidi            14984  1 snd_usbmidi_lib

Em Sat, 15 Sep 2012 19:39:31 +0200
Anders Thomson <[email protected]> escreveu:

There are lots of Pinnacle device supported by saa7134 driver. Without its PCI ID that's not much we can do.

Also, please post the dmesg showing what happens without and with your patch.

Regards,
Mauro

That here, right?
lspci -nvv:
03:06.0 0480: 1131:7133 (rev d1)
Subsystem: 11bd:002f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium

Latency: 64 (21000ns min, 8000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fdeff000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Kernel driver in use: saa7134
Kernel modules: saa7134

Coming. Hold on...

Em Sat, 15 Sep 2012 20:12:49 +0200
Anders Thomson <[email protected]> escreveu:

Thanks!

Please try the enclosed patch.

-

[PATCH] tda8290: Fix lna switch address

When LNA is configured with config 1 or config 2, tda827x driver will use the LNA switch_addr. However, this is not happening for all devices using such config, as reported by Anders. According to him, he is experiencing bad tuning with this code since Kenrel 2.6.26.

index 8c48521..bedc6ce 100644
@@ -627,6 +627,9 @@ static int tda829x_find_tuner(struct dvb_frontend *fe)
 		return -EREMOTEIO;
 	}
 
+	if (priv->cfg.config == 1 || priv->cfg.config == 2)
+		priv->cfg.switch_addr = priv->i2c_props.addr;
+
 	if ((data == 0x83) || (data == 0x84)) {
 		priv->ver |= TDA18271;
 		tda829x_tda18271_config.config = priv->cfg.config;

@@ -640,7 +643,6 @@ static int tda829x_find_tuner(struct dvb_frontend *fe)
 
 		dvb_attach(tda827x_attach, fe, priv->tda827x_addr,
 			   priv->i2c_props.adap, &priv->cfg);
-		priv->cfg.switch_addr = priv->i2c_props.addr;
 	}
 	if (fe->ops.tuner_ops.init)
 		fe->ops.tuner_ops.init(fe);

Regards,
Mauro

Em 16-09-2012 05:48, Anders Thomson escreveu:

I'm always using the very latest development tree:
http://git.linuxtv.org/media_tree.git

You can use the media_build.git tree to compile it against an older Kernel.

That's weird. Hmm... perhaps priv->cfg.config is being initialized latter. Maybe you can then do, instead:

                 return -EREMOTEIO;
         }

+        priv->cfg.switch_addr = priv->i2c_props.addr;
         if ((data == 0x83) || (data == 0x84)) {
                 priv->ver |= TDA18271;
                 tda829x_tda18271_config.config = priv->cfg.config;

This shouldn't cause any harm for tuners with config 0 or 3, as the switch address will never be used, anyway.

Regards,
Mauro

No dice:

 $ git diff | cat

index 8c48521..16d7ff7 100644
@@ -627,6 +627,9 @@ static int tda829x_find_tuner(struct dvb_frontend *fe)
                return -EREMOTEIO;
        }
 
+       tuner_info("ANDERS: old priv->cfg.switch_addr %x\n", priv->cfg.switch_addr);
+       priv->cfg.switch_addr = priv->i2c_props.addr;
+       tuner_info("ANDERS: new priv->cfg.switch_addr %x\n", priv->cfg.switch_addr);
        if ((data == 0x83) || (data == 0x84)) {
                priv->ver |= TDA18271;
                tda829x_tda18271_config.config = priv->cfg.config;

@@ -640,7 +643,6 @@ static int tda829x_find_tuner(struct dvb_frontend *fe)
 
                dvb_attach(tda827x_attach, fe, priv->tda827x_addr,
                           priv->i2c_props.adap, &priv->cfg);
-               priv->cfg.switch_addr = priv->i2c_props.addr;
        }
        if (fe->ops.tuner_ops.init)
                fe->ops.tuner_ops.init(fe);

anders@tv /usr/src/linux $ dmesg | grep ANDERS

[    5.667022] tda829x 4-004b: ANDERS: old priv->cfg.switch_addr 0
[    5.667025] tda829x 4-004b: ANDERS: new priv->cfg.switch_addr 4b

Whereas to work, I need:
anders@tv /usr/src/linux $ grep ANDERS /3.3.8-d.patched

[    6.565254] tda829x 5-004b: ANDERS: setting switch_addr. was 0x00, new 0x4b
[    6.565265] tda829x 5-004b: ANDERS: new 0x61

The right data should come from some i2d property I gather...
Is there any i2c CONFIG I need to have enabled to have this working automagically?

here's what I have:

$ zgrep I2C /proc/config.gz
# CONFIG_BMP085_I2C is not set
CONFIG_SENSORS_LIS3_I2C=y
# CONFIG_MOUSE_SYNAPTICS_I2C is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=m
# CONFIG_I2C_MUX is not set
CONFIG_I2C_HELPER_AUTO=y
CONFIG_I2C_SMBUS=m
CONFIG_I2C_ALGOBIT=y
# I2C Hardware Bus support
CONFIG_I2C_ALI1535=m
CONFIG_I2C_ALI1563=m
CONFIG_I2C_ALI15X3=m
CONFIG_I2C_AMD756=m
CONFIG_I2C_AMD756_S4882=m
CONFIG_I2C_AMD8111=m
CONFIG_I2C_I801=m
# CONFIG_I2C_ISCH is not set
CONFIG_I2C_PIIX4=m
CONFIG_I2C_NFORCE2=m
# CONFIG_I2C_NFORCE2_S4985 is not set
CONFIG_I2C_SIS5595=m
CONFIG_I2C_SIS630=m
CONFIG_I2C_SIS96X=m
CONFIG_I2C_VIA=m
CONFIG_I2C_VIAPRO=m
CONFIG_I2C_SCMI=m
# I2C system bus drivers (mostly embedded / system-on-chip)
# CONFIG_I2C_DESIGNWARE_PCI is not set
# CONFIG_I2C_EG20T is not set
# CONFIG_I2C_INTEL_MID is not set
CONFIG_I2C_OCORES=m
# CONFIG_I2C_PCA_PLATFORM is not set
# CONFIG_I2C_PXA_PCI is not set
CONFIG_I2C_SIMTEC=m
# CONFIG_I2C_XILINX is not set
# External I2C/SMBus adapter drivers
# CONFIG_I2C_DIOLAN_U2C is not set
CONFIG_I2C_PARPORT=m
CONFIG_I2C_PARPORT_LIGHT=m
CONFIG_I2C_TAOS_EVM=m
CONFIG_I2C_TINY_USB=m
# Other I2C/SMBus bus drivers
CONFIG_I2C_STUB=m
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_MFD_DA9052_I2C is not set
# CONFIG_MFD_WM831X_I2C is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_MC13XXX_I2C is not set
CONFIG_VIDEO_IR_I2C=m
# CONFIG_I2C_SI4713 is not set
# I2C encoder or helper chips
# CONFIG_DRM_I2C_CH7006 is not set
# CONFIG_DRM_I2C_SIL164 is not set
CONFIG_FB_RADEON_I2C=y
# I2C RTC drivers

Em 19-09-2012 10:01, Anders Thomson escreveu:

switch_addr got properly filled here.

What looks weird here is that the device number changed from 4 to 5.

Do you have more than one board on your machine?

The 0x61 address should be filled already by the existing code, otherwise you wouldn't be able to switch from one channel to another one.

If you're in doubt, you could add an extra printk at the initialization code, in order to see what's happening there.

Well, it got filled with 4b, but that it not what is needed. Recall my own patch:

# cat /TV_CARD.diff

index 064d14c..498cc7b 100644
@@ -635,7 +635,11 @@ static int tda829x_find_tuner(struct dvb_frontend *fe)
 
                dvb_attach(tda827x_attach, fe, priv->tda827x_addr,
                           priv->i2c_props.adap, &priv->cfg);
+               tuner_info("ANDERS: setting switch_addr. was 0x%02x, new 0x%02x\n",priv->cfg.switch_addr,priv->i2c_props.addr);
                priv->cfg.switch_addr = priv->i2c_props.addr;
+               priv->cfg.switch_addr = 0xc2 / 2;
+               tuner_info("ANDERS: new 0x%02x\n",priv->cfg.switch_addr);
+
        }
        if (fe->ops.tuner_ops.init)
                fe->ops.tuner_ops.init(fe);

It needs to be filled with 0xc2 / 2. I'm not sure where I got that expression from, but it is the sum of my efforts tracing code changes around 2.6.26.

I have a webcam permanently on USB, so it ends up as two v4l2 devices (with device enumeration changing between boots)

Not sure I follow here. Which code should set the ox61 address? I'd be more than happy to add printks. Where? I recall getting lost in how this stuff uses the i2c code in the past.

Em 21-09-2012 10:59, Anders Eriksson escreveu:

Are you using the active antena that came with this device[1]?

[1] http://www.mail-archive.com/[email protected]/msg07234.html

Em 22-09-2012 11:32, Anders Eriksson escreveu:

(please, don't top-post - it makes harder to preserve the history of the
discussions)

Then, maybe that's the reason why you're having troubles with this board.

The tda8290-based devices have two components:

1) a tda8275 tuner, at address 0x61 at the 7-bit I2C address notation (or 0xc2, at the 8-bit notation);
2) a tda8290 analog demod at address 0x4b (7-bit notation).

Some devices provide a way to send power to a low noise amplifier located at the antenna or at the device itself (called LNA). The way to activate the LNA is board-dependent.

On some devices the tda8290 can also be used to enable/disable a linear amplifier (LNA). Enabling/disabling the LNA and its gain affects the quality of the signal.

In the case of tda8275/tda8290 based devices, the LNA setup type is stored at priv->cfg->config, where:

	0 - means no LNA control at all - device won't use it;
	1, 2 - LNA is via a pin at tda8290 (GPIO 0):
		When config is 1, LNA high gain happens writing a 0;
		When config is 2, LNA high gain happens writing a 1;
	3 - The LNA gain control is via a pin at saa713x.

For modes 1 and 2, the switch_addr should be equal to 0x4b, as the commands sent to the device are for the tda8290 chip; sending them to tda8275 will likely produce no results or would affect something else there.

I suspect that, in the case of your board, the LNA is at the antenna bundled together with the device. If I'm right, by enabling LNA, your board is sending some voltage through the cabling (you could easily check it with a voltmeter).

What I think that your patch is actually doing is to disable LNA. As such, it should be equivalent to:

index bc08f1d..98b482e 100644
@@ -3288,13 +3288,13 @@ struct saa7134_board saa7134_boards[] = {
 		.name           = "Pinnacle PCTV 310i",
 		.audio_clock    = 0x00187de7,
 		.tuner_type     = TUNER_PHILIPS_TDA8290,
 		.radio_type     = UNSET,
 		.tuner_addr     = ADDR_UNSET,
 		.radio_addr     = ADDR_UNSET,
-		.tuner_config   = 1,
+		.tuner_config   = 0,
 		.mpeg           = SAA7134_MPEG_DVB,
 		.gpiomask       = 0x000200000,
 		.inputs         = {{
 			.name = name_tv,
 			.vmux = 4,
 			.amux = TV,

Please test if the above patch fixes the issue you're suffering[1]. If so, then we'll need to add a modprobe parameter to allow disabling LNA for saa7134 devices with LNA.

[1] Note: the above is not the fix, as some users of this board may be using the original antenna, and changing tuner_config will break things for them; the right fix is likely to allow controlling the LNA via userspace.

Regards,
Mauro

Sorry about that. I was using my notsosmartphone.

I actually have a multimeter somewhere. We're talking about the antenna-in (unconnected) on the card, right? And what voltages should I expect?

Tried that patch on 3.5.3. No improvement, unfortunately.

Regards,
/Anders

Em 23-09-2012 14:54, Anders Thomson escreveu:

zero (or close to zero) if LNA is disabled; some volts when LNA is enabled ;) According with Wikipedia[1]:

Usually LNA require less operating voltage in the range of 2 .. 10 V. MAX 2640 operate at +2.7 .. +5.5 V.

[1] http://en.wikipedia.org/wiki/Low-noise_amplifier

(Satellites amplifiers are typically 13V-18V - I never actually tried to use LNA for
terrestrial systems).

That's weird. Well, then we need to read tda827x datasheets and to try get information data from Pinnacle about this specific device configuration.

I have to retract that. It turns out that there is some strange interaction between the cabletv box and the card. When I rebooted into 'my' patch I still got the noisy signal. I then power cycled the cabletv box, and voila, I got a good signal on my own patch. Wondering what I had actually tested with your patch, I tested it again, and indeed it works!

So, 1) you're on to something, that's for sure, and 2) there is _something_ in the cabletv box which can make all this fall into a bad state too.

Cheers,
/Anders

Awfully sorry about this. After having had the familty sit in and check the differences, I must say that the patch does not fix the issue. This time around I have x11grabs with ffmpeg to show if you want.

I'll be away from the card until the end of the coming week. Then, I'll bring out the multimeter...

Best regards,
/Anders

So, I got the multimeter working over the weekend and pretty much no results there. :-(
I tested vanilla 3.5.3, w/ my patch, w/ your "tuner" patch. All three gave a (DC) reading of 0 to 30 mV (yes milli-). Given that the wiki page you referred to spoke of a few volts, I guess this is just noise. Coming to think of it, shouldn't any signal amplification done work on HF, so I'd have to measure the AC on the carrier freq or something? This multimeter is useless in the MHz range...

While at it, I created these 20 sec snippets:
http://pickup.famthomson.se/output-vanilla.avi
vanilla 3.5.3

http://pickup.famthomson.se/output-test3.avi
This patch:

 # cat /TV_TEST3.diff

index bc08f1d..98b482e 100644
@@ -3291,7 +3291,7 @@ struct saa7134_board saa7134_boards[] = {
                .radio_type     = UNSET,
                .tuner_addr     = ADDR_UNSET,
                .radio_addr     = ADDR_UNSET,
-               .tuner_config   = 1,
+               .tuner_config   = 0,
                .mpeg           = SAA7134_MPEG_DVB,
                .gpiomask       = 0x000200000,
                .inputs         = {{

http://pickup.famthomson.se/output-card.avi
This patch:

 # cat /TV_CARD.diff

index 064d14c..498cc7b 100644
@@ -635,7 +635,11 @@ static int tda829x_find_tuner(struct dvb_frontend *fe)
 
                dvb_attach(tda827x_attach, fe, priv->tda827x_addr,
                           priv->i2c_props.adap, &priv->cfg);
+               tuner_info("ANDERS: setting switch_addr. was 0x%02x, new 0x%02x\n",priv->cfg.switch_addr,priv->i2c_props.addr);
                priv->cfg.switch_addr = priv->i2c_props.addr;
+               priv->cfg.switch_addr = 0xc2 / 2;
+               tuner_info("ANDERS: new 0x%02x\n",priv->cfg.switch_addr);
+
        }
        if (fe->ops.tuner_ops.init)
                fe->ops.tuner_ops.init(fe);

Would looking again at the specifics on the 2.6.25->26 transition be of any help? I expect some pain to go to such old kernel, but if I can add some printks somewhere, maybe that could help?

Cheers,
-Anders

Hi Mauro,

Picking up this thread again. Did you have chance to look into this?

/Anders

Hi Mauro,

Any chance we can make progress on this one? As indicated, the patches you've proposed do not work. I have no idea why mine does though....

/Anders

dmesg, vanilla 3.3.8:

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.3.8 (root@tv) (gcc version 4.5.3 (Gentoo 4.5.3-r2 p1.1, pie-0.4.7) ) #70 SMP PREEMPT Sat Sep 15 20:22:03 CEST 2012
[    0.000000] Command line: root=/dev/sda3 hpet=disable crashkernel=128M
[    0.000000] KERNEL supported cpus:
[    0.000000]   AMD AuthenticAMD
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[    0.000000]  BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 0000000077ee0000 (usable)
[    0.000000]  BIOS-e820: 0000000077ee0000 - 0000000077ee3000 (ACPI NVS)
[    0.000000]  BIOS-e820: 0000000077ee3000 - 0000000077ef0000 (ACPI data)
[    0.000000]  BIOS-e820: 0000000077ef0000 - 0000000077f00000 (reserved)
[    0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] DMI 2.4 present.
[    0.000000] DMI: System manufacturer System Product Name/M2A-VM HDMI, BIOS ASUS M2A-VM HDMI ACPI BIOS Revision 2201 10/22/2008
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] No AGP bridge found
[    0.000000] last_pfn = 0x77ee0 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-C7FFF write-protect
[    0.000000]   C8000-FFFFF uncachable
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 0000000000 mask FFC0000000 write-back
[    0.000000]   1 base 0040000000 mask FFE0000000 write-back
[    0.000000]   2 base 0060000000 mask FFF0000000 write-back
[    0.000000]   3 base 0070000000 mask FFF8000000 write-back
[    0.000000]   4 base 0077F00000 mask FFFFF00000 uncachable
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] found SMP MP-table at [ffff8800000f6560] f6560
[    0.000000] initial memory mapped : 0 - 20000000
[    0.000000] Base memory trampoline at [ffff88000009a000] 9a000 size 20480
[    0.000000] init_memory_mapping: 0000000000000000-0000000077ee0000
[    0.000000]  0000000000 - 0077e00000 page 2M
[    0.000000]  0077e00000 - 0077ee0000 page 4k
[    0.000000] kernel direct mapping tables up to 77ee0000 @ 1fffc000-20000000
[    0.000000] Reserving 128MB of memory at 768MB for crashkernel (System RAM: 1918MB)
[    0.000000] ACPI: RSDP 00000000000f8210 00024 (v02 ATI   )
[    0.000000] ACPI: XSDT 0000000077ee3100 00044 (v01 ATI    ASUSACPI 42302E31 AWRD 00000000)
[    0.000000] ACPI: FACP 0000000077ee8500 000F4 (v03 ATI    ASUSACPI 42302E31 AWRD 00000000)
[    0.000000] ACPI: DSDT 0000000077ee3280 05210 (v01 ATI    ASUSACPI 00001000 MSFT 03000000)
[    0.000000] ACPI: FACS 0000000077ee0000 00040
[    0.000000] ACPI: SSDT 0000000077ee8740 002CC (v01 PTLTD  POWERNOW 00000001  LTP 00000001)
[    0.000000] ACPI: MCFG 0000000077ee8b00 0003C (v01 ATI    ASUSACPI 42302E31 AWRD 00000000)
[    0.000000] ACPI: APIC 0000000077ee8640 00084 (v01 ATI    ASUSACPI 42302E31 AWRD 00000000)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000]  [ffffea0000000000-ffffea0001bfffff] PMD -> [ffff880075800000-ffff8800773fffff] on node 0
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   empty
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x00077ee0
[    0.000000] On node 0 totalpages: 491119
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 5 pages reserved
[    0.000000]   DMA zone: 3922 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 6661 pages used for memmap
[    0.000000]   DMA32 zone: 480475 pages, LIFO batch:31
[    0.000000] Detected use of extended apic ids on hypertransport bus
[    0.000000] ACPI: PM-Timer IO Port: 0x4008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[    0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at 77f00000 (gap: 77f00000:68100000)
[    0.000000] setup_percpu: NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 25 pages/cpu @ffff880077c00000 s71424 r8192 d22784 u524288
[    0.000000] pcpu-alloc: s71424 r8192 d22784 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 484397
[    0.000000] Kernel command line: root=/dev/sda3 hpet=disable crashkernel=128M
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Node 0: aperture @ 1066000000 size 32 MB
[    0.000000] Aperture beyond 4GB. Ignoring.
[    0.000000] Memory: 1791420k/1964928k available (5100k kernel code, 452k absent, 173056k reserved, 3466k data, 456k init)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  CONFIG_RCU_FANOUT set to non-default value of 32
[    0.000000] NR_IRQS:4352 nr_irqs:712 16
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] allocated 7864320 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 2799.741 MHz processor.
[    0.000000] Marking TSC unstable due to TSCs unsynchronized
[    0.002038] Calibrating delay loop (skipped), value calculated using timer frequency.. 5599.48 BogoMIPS (lpj=2799741)
[    0.002109] pid_max: default: 32768 minimum: 301
[    0.002215] Mount-cache hash table entries: 256
[    0.002390] Initializing cgroup subsys cpuacct
[    0.002426] Initializing cgroup subsys memory
[    0.002474] Initializing cgroup subsys devices
[    0.003003] Initializing cgroup subsys freezer
[    0.003038] Initializing cgroup subsys blkio
[    0.003108] tseg: 0077f00000
[    0.003110] CPU: Physical Processor ID: 0
[    0.003145] CPU: Processor Core ID: 0
[    0.003180] mce: CPU supports 5 MCE banks
[    0.003226] using AMD E400 aware idle routine
[    0.003299] ACPI: Core revision 20120111
[    0.006535] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.016582] CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 5600+ stepping 03
[    0.016998] Performance Events: AMD PMU driver.
[    0.016998] ... version:                0
[    0.016998] ... bit width:              48
[    0.016998] ... generic registers:      4
[    0.016998] ... value mask:             0000ffffffffffff
[    0.016998] ... max period:             00007fffffffffff
[    0.016998] ... fixed-purpose events:   0
[    0.016998] ... event mask:             000000000000000f
[    0.028011] Booting Node   0, Processors  #1
[    0.028073] smpboot cpu 1: start_ip = 9a000
[    0.099087] Brought up 2 CPUs
[    0.099121] Total of 2 processors activated (11198.19 BogoMIPS).
[    0.099618] PM: Registering ACPI NVS region at 77ee0000 (12288 bytes)
[    0.100061] NET: Registered protocol family 16
[    0.100114] node 0 link 0: io port [c000, ffff]
[    0.100114] TOM: 0000000080000000 aka 2048M
[    0.100114] node 0 link 0: mmio [a0000, bffff]
[    0.100114] node 0 link 0: mmio [80000000, dfffffff]
[    0.100114] node 0 link 0: mmio [f0000000, fe02ffff]
[    0.100114] node 0 link 0: mmio [e0000000, e03fffff]
[    0.100114] bus: [00, 03] on node 0 link 0
[    0.100114] bus: 00 index 0 [io  0x0000-0xffff]
[    0.100114] bus: 00 index 1 [mem 0x000a0000-0x000bffff]
[    0.100114] bus: 00 index 2 [mem 0x80000000-0xefffffff]
[    0.100114] bus: 00 index 3 [mem 0xf0000000-0xfcffffffff]
[    0.100114] ACPI: bus type pci registered
[    0.100121] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.100121] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[    0.118731] PCI: Using configuration type 1 for base access
[    0.126068] bio: create slab <bio-0> at 0
[    0.126123] ACPI: Added _OSI(Module Device)
[    0.126123] ACPI: Added _OSI(Processor Device)
[    0.126123] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.126125] ACPI: Added _OSI(Processor Aggregator Device)
[    0.127242] ACPI: EC: Look up EC in DSDT
[    0.130804] ACPI: Interpreter enabled
[    0.130842] ACPI: (supports S0 S1 S3 S4 S5)
[    0.131024] ACPI: Using IOAPIC for interrupt routing
[    0.136096] ACPI: No dock devices found.
[    0.136139] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.136238] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.136344] pci_root PNP0A03:00: host bridge window [io  0x0000-0x0cf7]
[    0.136381] pci_root PNP0A03:00: host bridge window [io  0x0d00-0xffff]
[    0.136418] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
[    0.136457] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000dffff]
[    0.136497] pci_root PNP0A03:00: host bridge window [mem 0x80000000-0xfebfffff]
[    0.137066] PCI host bridge to bus 0000:00
[    0.137066] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.137078] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff]
[    0.137114] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.137150] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff]
[    0.137187] pci_bus 0000:00: root bus resource [mem 0x80000000-0xfebfffff]
[    0.137233] pci 0000:00:00.0: [1002:7910] type 0 class 0x000600
[    0.137262] pci 0000:00:01.0: [1002:7912] type 1 class 0x000604
[    0.137299] pci 0000:00:07.0: [1002:7917] type 1 class 0x000604
[    0.137328] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
[    0.137358] pci 0000:00:12.0: [1002:4380] type 0 class 0x000101
[    0.137377] pci 0000:00:12.0: reg 10: [io  0xff00-0xff07]
[    0.137387] pci 0000:00:12.0: reg 14: [io  0xfe00-0xfe03]
[    0.137398] pci 0000:00:12.0: reg 18: [io  0xfd00-0xfd07]
[    0.137408] pci 0000:00:12.0: reg 1c: [io  0xfc00-0xfc03]
[    0.137418] pci 0000:00:12.0: reg 20: [io  0xfb00-0xfb0f]
[    0.137429] pci 0000:00:12.0: reg 24: [mem 0xfe02f000-0xfe02f3ff]
[    0.137450] pci 0000:00:12.0: set SATA to AHCI mode
[    0.137522] pci 0000:00:13.0: [1002:4387] type 0 class 0x000c03
[    0.137536] pci 0000:00:13.0: reg 10: [mem 0xfe02e000-0xfe02efff]
[    0.137604] pci 0000:00:13.1: [1002:4388] type 0 class 0x000c03
[    0.137619] pci 0000:00:13.1: reg 10: [mem 0xfe02d000-0xfe02dfff]
[    0.137687] pci 0000:00:13.2: [1002:4389] type 0 class 0x000c03
[    0.137702] pci 0000:00:13.2: reg 10: [mem 0xfe02c000-0xfe02cfff]
[    0.137770] pci 0000:00:13.3: [1002:438a] type 0 class 0x000c03
[    0.137784] pci 0000:00:13.3: reg 10: [mem 0xfe02b000-0xfe02bfff]
[    0.137854] pci 0000:00:13.4: [1002:438b] type 0 class 0x000c03
[    0.137868] pci 0000:00:13.4: reg 10: [mem 0xfe02a000-0xfe02afff]
[    0.138040] pci 0000:00:13.5: [1002:4386] type 0 class 0x000c03
[    0.138060] pci 0000:00:13.5: reg 10: [mem 0xfe029000-0xfe0290ff]
[    0.138147] pci 0000:00:13.5: supports D1 D2
[    0.138149] pci 0000:00:13.5: PME# supported from D0 D1 D2 D3hot
[    0.138174] pci 0000:00:14.0: [1002:4385] type 0 class 0x000c05
[    0.138197] pci 0000:00:14.0: reg 10: [io  0x0b00-0x0b0f]
[    0.138284] pci 0000:00:14.1: [1002:438c] type 0 class 0x000101
[    0.138298] pci 0000:00:14.1: reg 10: [io  0x0000-0x0007]
[    0.138309] pci 0000:00:14.1: reg 14: [io  0x0000-0x0003]
[    0.138319] pci 0000:00:14.1: reg 18: [io  0x0000-0x0007]
[    0.138329] pci 0000:00:14.1: reg 1c: [io  0x0000-0x0003]
[    0.138340] pci 0000:00:14.1: reg 20: [io  0xf900-0xf90f]
[    0.138380] pci 0000:00:14.2: [1002:4383] type 0 class 0x000403
[    0.138403] pci 0000:00:14.2: reg 10: [mem 0xfe020000-0xfe023fff 64bit]
[    0.138473] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[    0.138489] pci 0000:00:14.3: [1002:438d] type 0 class 0x000601
[    0.138567] pci 0000:00:14.4: [1002:4384] type 1 class 0x000604
[    0.138616] pci 0000:00:18.0: [1022:1100] type 0 class 0x000600
[    0.138634] pci 0000:00:18.1: [1022:1101] type 0 class 0x000600
[    0.138647] pci 0000:00:18.2: [1022:1102] type 0 class 0x000600
[    0.138662] pci 0000:00:18.3: [1022:1103] type 0 class 0x000600
[    0.138705] pci 0000:01:05.0: [1002:791e] type 0 class 0x000300
[    0.138713] pci 0000:01:05.0: reg 10: [mem 0xf0000000-0xf7ffffff 64bit pref]
[    0.138719] pci 0000:01:05.0: reg 18: [mem 0xfdbe0000-0xfdbeffff 64bit]
[    0.138724] pci 0000:01:05.0: reg 20: [io  0xde00-0xdeff]
[    0.138729] pci 0000:01:05.0: reg 24: [mem 0xfda00000-0xfdafffff]
[    0.138744] pci 0000:01:05.0: supports D1 D2
[    0.138755] pci 0000:01:05.2: [1002:7919] type 0 class 0x000403
[    0.138763] pci 0000:01:05.2: reg 10: [mem 0xfdbfc000-0xfdbfffff 64bit]
[    0.138799] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.138836] pci 0000:00:01.0:   bridge window [io  0xd000-0xdfff]
[    0.138839] pci 0000:00:01.0:   bridge window [mem 0xfda00000-0xfdbfffff]
[    0.138843] pci 0000:00:01.0:   bridge window [mem 0xf0000000-0xf7ffffff 64bit pref]
[    0.138883] pci 0000:02:00.0: [10ec:8168] type 0 class 0x000200
[    0.138897] pci 0000:02:00.0: reg 10: [io  0xee00-0xeeff]
[    0.138921] pci 0000:02:00.0: reg 18: [mem 0xfdfff000-0xfdffffff 64bit]
[    0.138950] pci 0000:02:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[    0.139028] pci 0000:02:00.0: supports D1 D2
[    0.139030] pci 0000:02:00.0: PME# supported from D1 D2 D3hot D3cold
[    0.139047] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.139094] pci 0000:00:07.0: PCI bridge to [bus 02-02]
[    0.139131] pci 0000:00:07.0:   bridge window [io  0xe000-0xefff]
[    0.139134] pci 0000:00:07.0:   bridge window [mem 0xfdf00000-0xfdffffff]
[    0.139138] pci 0000:00:07.0:   bridge window [mem 0xfdc00000-0xfdcfffff 64bit pref]
[    0.139175] pci 0000:03:06.0: [1131:7133] type 0 class 0x000480
[    0.139200] pci 0000:03:06.0: reg 10: [mem 0xfdeff000-0xfdeff7ff]
[    0.139302] pci 0000:03:06.0: supports D1 D2
[    0.139325] pci 0000:03:07.0: [1106:3044] type 0 class 0x000c00
[    0.139348] pci 0000:03:07.0: reg 10: [mem 0xfdefe000-0xfdefe7ff]
[    0.139362] pci 0000:03:07.0: reg 14: [io  0xcf00-0xcf7f]
[    0.139457] pci 0000:03:07.0: supports D2
[    0.139459] pci 0000:03:07.0: PME# supported from D2 D3hot D3cold
[    0.139509] pci 0000:00:14.4: PCI bridge to [bus 03-03] (subtractive decode)
[    0.139547] pci 0000:00:14.4:   bridge window [io  0xc000-0xcfff]
[    0.139552] pci 0000:00:14.4:   bridge window [mem 0xfde00000-0xfdefffff]
[    0.139556] pci 0000:00:14.4:   bridge window [mem 0xfdd00000-0xfddfffff pref]
[    0.139559] pci 0000:00:14.4:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.139562] pci 0000:00:14.4:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.139564] pci 0000:00:14.4:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.139567] pci 0000:00:14.4:   bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[    0.139570] pci 0000:00:14.4:   bridge window [mem 0x80000000-0xfebfffff] (subtractive decode)
[    0.139581] pci_bus 0000:00: on NUMA node 0
[    0.139584] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.139730] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[    0.139801] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE7._PRT]
[    0.139828] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[    0.139859]  pci0000:00: Requesting ACPI _OSC control (0x1d)
[    0.139897]  pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
[    0.139936] ACPI _OSC control for PCIe not granted, disabling ASPM
[    0.154048] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[    0.154443] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[    0.155085] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[    0.155482] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[    0.155877] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[    0.156289] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[    0.156683] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 *11)
[    0.157033] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[    0.157418] vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks=none
[    0.157418] vgaarb: loaded
[    0.157418] vgaarb: bridge control possible 0000:01:05.0
[    0.157418] SCSI subsystem initialized
[    0.158009] libata version 3.00 loaded.
[    0.158021] usbcore: registered new interface driver usbfs
[    0.158051] usbcore: registered new interface driver hub
[    0.158051] usbcore: registered new device driver usb
[    0.158051] Advanced Linux Sound Architecture Driver Version 1.0.24.
[    0.158051] PCI: Using ACPI for IRQ routing
[    0.167908] PCI: pci_cache_line_size set to 64 bytes
[    0.167992] reserve RAM buffer: 000000000009f000 - 000000000009ffff
[    0.167994] reserve RAM buffer: 0000000077ee0000 - 0000000077ffffff
[    0.168064] Bluetooth: Core ver 2.16
[    0.168068] NET: Registered protocol family 31
[    0.168068] Bluetooth: HCI device and connection manager initialized
[    0.168070] Bluetooth: HCI socket layer initialized
[    0.168105] Bluetooth: L2CAP socket layer initialized
[    0.168985] Bluetooth: SCO socket layer initialized
[    0.169090] pnp: PnP ACPI init
[    0.169090] ACPI: bus type pnp registered
[    0.169150] pnp 00:00: [bus 00-ff]
[    0.169153] pnp 00:00: [io  0x0cf8-0x0cff]
[    0.169155] pnp 00:00: [io  0x0000-0x0cf7 window]
[    0.169157] pnp 00:00: [io  0x0d00-0xffff window]
[    0.169160] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    0.169162] pnp 00:00: [mem 0x000c0000-0x000dffff window]
[    0.169165] pnp 00:00: [mem 0x80000000-0xfebfffff window]
[    0.169222] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
[    0.169222] pnp 00:01: [io  0x4100-0x411f]
[    0.169222] pnp 00:01: [io  0x0228-0x022f]
[    0.169222] pnp 00:01: [io  0x040b]
[    0.169222] pnp 00:01: [io  0x04d6]
[    0.169222] pnp 00:01: [io  0x0c00-0x0c01]
[    0.169222] pnp 00:01: [io  0x0c14]
[    0.169222] pnp 00:01: [io  0x0c50-0x0c52]
[    0.169222] pnp 00:01: [io  0x0c6c-0x0c6d]
[    0.169222] pnp 00:01: [io  0x0c6f]
[    0.169222] pnp 00:01: [io  0x0cd0-0x0cd1]
[    0.169222] pnp 00:01: [io  0x0cd2-0x0cd3]
[    0.169222] pnp 00:01: [io  0x0cd4-0x0cdf]
[    0.169222] pnp 00:01: [io  0x4000-0x40fe]
[    0.169222] pnp 00:01: [io  0x4210-0x4217]
[    0.169222] pnp 00:01: [io  0x0b10-0x0b1f]
[    0.169222] pnp 00:01: [mem 0x00000000-0x00000fff window]
[    0.169222] pnp 00:01: [mem 0xfee00400-0xfee00fff window]
[    0.169222] pnp 00:01: disabling [mem 0x00000000-0x00000fff window] because it overlaps 0000:02:00.0 BAR 6 [mem 0x00000000-0x0001ffff pref]
[    0.169222] system 00:01: [io  0x4100-0x411f] has been reserved
[    0.169222] system 00:01: [io  0x0228-0x022f] has been reserved
[    0.169985] system 00:01: [io  0x040b] has been reserved
[    0.170022] system 00:01: [io  0x04d6] has been reserved
[    0.170058] system 00:01: [io  0x0c00-0x0c01] has been reserved
[    0.170094] system 00:01: [io  0x0c14] has been reserved
[    0.170130] system 00:01: [io  0x0c50-0x0c52] has been reserved
[    0.170166] system 00:01: [io  0x0c6c-0x0c6d] has been reserved
[    0.170201] system 00:01: [io  0x0c6f] has been reserved
[    0.170237] system 00:01: [io  0x0cd0-0x0cd1] has been reserved
[    0.170273] system 00:01: [io  0x0cd2-0x0cd3] has been reserved
[    0.170309] system 00:01: [io  0x0cd4-0x0cdf] has been reserved
[    0.170345] system 00:01: [io  0x4000-0x40fe] has been reserved
[    0.170381] system 00:01: [io  0x4210-0x4217] has been reserved
[    0.170417] system 00:01: [io  0x0b10-0x0b1f] has been reserved
[    0.170454] system 00:01: [mem 0xfee00400-0xfee00fff window] has been reserved
[    0.170494] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.170587] pnp 00:02: [dma 4]
[    0.170589] pnp 00:02: [io  0x0000-0x000f]
[    0.170592] pnp 00:02: [io  0x0080-0x0090]
[    0.170594] pnp 00:02: [io  0x0094-0x009f]
[    0.170596] pnp 00:02: [io  0x00c0-0x00df]
[    0.170634] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.170634] pnp 00:03: [io  0x0070-0x0073]
[    0.170634] pnp 00:03: [irq 8]
[    0.170634] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.170634] pnp 00:04: [io  0x0061]
[    0.170634] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.170634] pnp 00:05: [io  0x00f0-0x00ff]
[    0.170634] pnp 00:05: [irq 13]
[    0.170634] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.170634] pnp 00:06: [io  0x0010-0x001f]
[    0.170634] pnp 00:06: [io  0x0022-0x003f]
[    0.170634] pnp 00:06: [io  0x0044-0x005f]
[    0.170634] pnp 00:06: [io  0x0062-0x0063]
[    0.170634] pnp 00:06: [io  0x0065-0x006f]
[    0.170634] pnp 00:06: [io  0x0074-0x007f]
[    0.170634] pnp 00:06: [io  0x0091-0x0093]
[    0.170634] pnp 00:06: [io  0x00a2-0x00bf]
[    0.170634] pnp 00:06: [io  0x00e0-0x00ef]
[    0.170634] pnp 00:06: [io  0x04d0-0x04d1]
[    0.170984] pnp 00:06: [io  0x0220-0x0225]
[    0.171042] system 00:06: [io  0x04d0-0x04d1] has been reserved
[    0.171042] system 00:06: [io  0x0220-0x0225] has been reserved
[    0.171076] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.171200] pnp 00:07: [io  0x03f0-0x03f5]
[    0.171203] pnp 00:07: [io  0x03f7]
[    0.171212] pnp 00:07: [irq 6]
[    0.171214] pnp 00:07: [dma 2]
[    0.171262] pnp 00:07: Plug and Play ACPI device, IDs PNP0700 (active)
[    0.171262] pnp 00:08: [io  0x03f8-0x03ff]
[    0.171262] pnp 00:08: [irq 4]
[    0.171262] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.171262] pnp 00:09: [io  0x0378-0x037f]
[    0.171265] pnp 00:09: [irq 7]
[    0.171320] pnp 00:09: Plug and Play ACPI device, IDs PNP0400 (active)
[    0.172084] pnp 00:0a: [mem 0xe0000000-0xefffffff]
[    0.172138] system 00:0a: [mem 0xe0000000-0xefffffff] has been reserved
[    0.172138] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.172162] pnp 00:0b: [mem 0x000cd600-0x000cffff]
[    0.172165] pnp 00:0b: [mem 0x000f0000-0x000f7fff]
[    0.172167] pnp 00:0b: [mem 0x000f8000-0x000fbfff]
[    0.172169] pnp 00:0b: [mem 0x000fc000-0x000fffff]
[    0.172171] pnp 00:0b: [mem 0x77ef0000-0x77feffff]
[    0.172174] pnp 00:0b: [mem 0xfed00000-0xfed000ff]
[    0.172176] pnp 00:0b: [mem 0x77ee0000-0x77efffff]
[    0.172179] pnp 00:0b: [mem 0xffff0000-0xffffffff]
[    0.172181] pnp 00:0b: [mem 0x00000000-0x0009ffff]
[    0.172183] pnp 00:0b: [mem 0x00100000-0x77edffff]
[    0.172185] pnp 00:0b: [mem 0x77ff0000-0x7ffeffff]
[    0.172188] pnp 00:0b: [mem 0xfec00000-0xfec00fff]
[    0.172190] pnp 00:0b: [mem 0xfee00000-0xfee00fff]
[    0.172192] pnp 00:0b: [mem 0xfff80000-0xfffeffff]
[    0.172259] system 00:0b: [mem 0x000cd600-0x000cffff] has been reserved
[    0.172259] system 00:0b: [mem 0x000f0000-0x000f7fff] could not be reserved
[    0.172259] system 00:0b: [mem 0x000f8000-0x000fbfff] could not be reserved
[    0.172259] system 00:0b: [mem 0x000fc000-0x000fffff] could not be reserved
[    0.172259] system 00:0b: [mem 0x77ef0000-0x77feffff] could not be reserved
[    0.172259] system 00:0b: [mem 0xfed00000-0xfed000ff] has been reserved
[    0.172259] system 00:0b: [mem 0x77ee0000-0x77efffff] could not be reserved
[    0.172260] system 00:0b: [mem 0xffff0000-0xffffffff] has been reserved
[    0.172297] system 00:0b: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.172334] system 00:0b: [mem 0x00100000-0x77edffff] could not be reserved
[    0.172371] system 00:0b: [mem 0x77ff0000-0x7ffeffff] could not be reserved
[    0.172407] system 00:0b: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.172444] system 00:0b: [mem 0xfee00000-0xfee00fff] could not be reserved
[    0.172480] system 00:0b: [mem 0xfff80000-0xfffeffff] has been reserved
[    0.172517] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.172524] pnp: PnP ACPI: found 12 devices
[    0.172984] ACPI: ACPI bus type pnp unregistered
[    0.181330] Switching to clocksource acpi_pm
[    0.181399] PCI: max bus depth: 1 pci_try_num: 2
[    0.181419] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.181455] pci 0000:00:01.0:   bridge window [io  0xd000-0xdfff]
[    0.181492] pci 0000:00:01.0:   bridge window [mem 0xfda00000-0xfdbfffff]
[    0.181529] pci 0000:00:01.0:   bridge window [mem 0xf0000000-0xf7ffffff 64bit pref]
[    0.181573] pci 0000:02:00.0: BAR 6: assigned [mem 0xfdc00000-0xfdc1ffff pref]
[    0.181612] pci 0000:00:07.0: PCI bridge to [bus 02-02]
[    0.181648] pci 0000:00:07.0:   bridge window [io  0xe000-0xefff]
[    0.181684] pci 0000:00:07.0:   bridge window [mem 0xfdf00000-0xfdffffff]
[    0.181721] pci 0000:00:07.0:   bridge window [mem 0xfdc00000-0xfdcfffff 64bit pref]
[    0.181762] pci 0000:00:14.4: PCI bridge to [bus 03-03]
[    0.181799] pci 0000:00:14.4:   bridge window [io  0xc000-0xcfff]
[    0.181838] pci 0000:00:14.4:   bridge window [mem 0xfde00000-0xfdefffff]
[    0.181877] pci 0000:00:14.4:   bridge window [mem 0xfdd00000-0xfddfffff pref]
[    0.181933] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.181935] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.181937] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.181940] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff]
[    0.181943] pci_bus 0000:00: resource 8 [mem 0x80000000-0xfebfffff]
[    0.181945] pci_bus 0000:01: resource 0 [io  0xd000-0xdfff]
[    0.181948] pci_bus 0000:01: resource 1 [mem 0xfda00000-0xfdbfffff]
[    0.181950] pci_bus 0000:01: resource 2 [mem 0xf0000000-0xf7ffffff 64bit pref]
[    0.181953] pci_bus 0000:02: resource 0 [io  0xe000-0xefff]
[    0.181955] pci_bus 0000:02: resource 1 [mem 0xfdf00000-0xfdffffff]
[    0.181958] pci_bus 0000:02: resource 2 [mem 0xfdc00000-0xfdcfffff 64bit pref]
[    0.181960] pci_bus 0000:03: resource 0 [io  0xc000-0xcfff]
[    0.181963] pci_bus 0000:03: resource 1 [mem 0xfde00000-0xfdefffff]
[    0.181965] pci_bus 0000:03: resource 2 [mem 0xfdd00000-0xfddfffff pref]
[    0.181968] pci_bus 0000:03: resource 4 [io  0x0000-0x0cf7]
[    0.181970] pci_bus 0000:03: resource 5 [io  0x0d00-0xffff]
[    0.181972] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]
[    0.181975] pci_bus 0000:03: resource 7 [mem 0x000c0000-0x000dffff]
[    0.181977] pci_bus 0000:03: resource 8 [mem 0x80000000-0xfebfffff]
[    0.181977] NET: Registered protocol family 2
[    0.181977] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.182269] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[    0.184768] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.185422] TCP: Hash tables configured (established 262144 bind 65536)
[    0.185459] TCP reno registered
[    0.185497] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[    0.185551] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[    0.185695] NET: Registered protocol family 1
[    0.185858] RPC: Registered named UNIX socket transport module.
[    0.185904] RPC: Registered udp transport module.
[    0.185939] RPC: Registered tcp transport module.
[    0.185973] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.463071] pci 0000:01:05.0: Boot video device
[    0.463083] PCI: CLS 32 bytes, default 64
[    0.463218] kvm: Nested Virtualization enabled
[    0.464192] audit: initializing netlink socket (disabled)
[    0.464241] type=2000 audit(1347733502.464:1): initialized
[    0.465367] Installing knfsd (copyright (C) 1996 [email protected]).
[    0.465695] msgmni has been set to 3498
[    0.466202] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.466245] io scheduler noop registered
[    0.466306] io scheduler cfq registered (default)
[    0.466502] pcieport 0000:00:07.0: irq 40 for MSI/MSI-X
[    0.467202] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[    0.467246] ACPI: Power Button [PWRB]
[    0.467394] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    0.467436] ACPI: Power Button [PWRF]
[    0.467614] ACPI: Fan [FAN] (on)
[    0.469243] ACPI Warning: For \_TZ_.THRM._PSL: Return Package has no elements (empty) (20120111/nspredef-463)
[    0.469346] ACPI: [Package] has zero elements (ffff880074b6ae80)
[    0.469381] ACPI: Invalid passive threshold
[    0.469659] thermal LNXTHERM:00: registered as thermal_zone0
[    0.469695] ACPI: Thermal Zone [THRM] (40 C)
[    0.469960] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.490721] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.511850] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.512309] [drm] Initialized drm 1.1.0 20060810
[    0.512402] [drm] radeon defaulting to kernel modesetting.
[    0.512438] [drm] radeon kernel modesetting enabled.
[    0.512724] [drm] initializing kernel modesetting (RS690 0x1002:0x791E 0x1043:0x826D).
[    0.512780] [drm] register mmio base: 0xFDBE0000
[    0.512814] [drm] register mmio size: 65536
[    0.514392] ATOM BIOS: ATI
[    0.514444] radeon 0000:01:05.0: VRAM: 128M 0x0000000078000000 - 0x000000007FFFFFFF (128M used)
[    0.514486] radeon 0000:01:05.0: GTT: 512M 0x0000000080000000 - 0x000000009FFFFFFF
[    0.514526] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    0.514562] [drm] Driver supports precise vblank timestamp query.
[    0.514623] [drm] radeon: irq initialized.
[    0.515278] [drm] Detected VRAM RAM=128M, BAR=128M
[    0.515318] [drm] RAM width 128bits DDR
[    0.515437] [TTM] Zone  kernel: Available graphics memory: 895710 kiB.
[    0.515477] [TTM] Initializing pool allocator.
[    0.515519] [TTM] Initializing DMA pool allocator.
[    0.515583] [drm] radeon: 128M of VRAM memory ready
[    0.515618] [drm] radeon: 512M of GTT memory ready.
[    0.515655] [drm] GART: num cpu pages 131072, num gpu pages 131072
[    0.522364] [drm] radeon: ib pool ready.
[    0.523410] [drm] radeon: 1 quad pipes, 1 z pipes initialized.
[    0.529504] [drm] PCIE GART of 512M enabled (table at 0x0000000074680000).
[    0.529559] radeon 0000:01:05.0: WB enabled
[    0.529595] [drm] fence driver on ring 0 use gpu addr 0x80000000 and cpu addr 0xffff8800744c8000
[    0.529754] [drm] Loading RS690/RS740 Microcode
[    0.529971] [drm] radeon: ring at 0x0000000080001000
[    0.530031] [drm] ring test succeeded in 1 usecs
[    0.530178] [drm] ib test succeeded in 0 usecs
[    0.530978] [drm] Radeon Display Connectors
[    0.531023] [drm] Connector 0:
[    0.531058] [drm]   VGA
[    0.531092] [drm]   DDC: 0x7e50 0x7e40 0x7e54 0x7e44 0x7e58 0x7e48 0x7e5c 0x7e4c
[    0.531130] [drm]   Encoders:
[    0.531164] [drm]     CRT1: INTERNAL_KLDSCP_DAC1
[    0.531199] [drm] Connector 1:
[    0.531232] [drm]   S-video
[    0.531265] [drm]   Encoders:
[    0.531299] [drm]     TV1: INTERNAL_KLDSCP_DAC1
[    0.531333] [drm] Connector 2:
[    0.531367] [drm]   HDMI-A
[    0.531400] [drm]   HPD2
[    0.531434] [drm]   DDC: 0x7e40 0x7e60 0x7e44 0x7e64 0x7e48 0x7e68 0x7e4c 0x7e6c
[    0.531472] [drm]   Encoders:
[    0.531506] [drm]     DFP2: INTERNAL_DDI
[    0.531539] [drm] Connector 3:
[    0.531573] [drm]   DVI-D
[    0.531607] [drm]   DDC: 0x7e40 0x7e50 0x7e44 0x7e54 0x7e48 0x7e58 0x7e4c 0x7e5c
[    0.531645] [drm]   Encoders:
[    0.531678] [drm]     DFP3: INTERNAL_LVTM1
[    0.788240] [drm] fb mappable at 0xF0040000
[    0.788275] [drm] vram apper at 0xF0000000
[    0.788309] [drm] size 8294400
[    0.788343] [drm] fb depth is 24
[    0.788376] [drm]    pitch is 7680
[    0.788497] fbcon: radeondrmfb (fb0) is primary device
[    0.816768] Console: switching to colour frame buffer device 240x67
[    0.826047] fb0: radeondrmfb frame buffer device
[    0.826081] drm: registered panic notifier
[    0.826115] [drm] Initialized radeon 2.13.0 20080528 for 0000:01:05.0 on minor 0
[    0.829054] brd: module loaded
[    0.830587] loop: module loaded
[    0.830669] Uniform Multi-Platform E-IDE driver
[    0.830841] ide-gd driver 1.18
[    0.831164] ahci 0000:00:12.0: version 3.0
[    0.831213] ahci 0000:00:12.0: ASUS M2A-VM: enabling 64bit DMA
[    0.831378] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[    0.831442] ahci 0000:00:12.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc
[    0.833119] scsi0 : ahci
[    0.833451] scsi1 : ahci
[    0.833680] scsi2 : ahci
[    0.833903] scsi3 : ahci
[    0.834164] ata1: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100 irq 22
[    0.834221] ata2: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180 irq 22
[    0.834277] ata3: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200 irq 22
[    0.834333] ata4: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280 irq 22
[    0.834643] tun: Universal TUN/TAP device driver, 1.6
[    0.834682] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[    0.834813] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    0.834948] r8169 0000:02:00.0: irq 41 for MSI/MSI-X
[    0.835349] r8169 0000:02:00.0: eth0: RTL8168b/8111b at 0xffffc9000000c000, 00:1b:fc:89:fa:a2, XID 18000000 IRQ 41
[    0.835427] r8169 0000:02:00.0: eth0: jumbo features [frames: 4080 bytes, tx checksumming: ko]
[    0.835552] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.835624] ehci_hcd 0000:00:13.5: EHCI Host Controller
[    0.835669] ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 1
[    0.835749] ehci_hcd 0000:00:13.5: applying AMD SB600/SB700 USB freeze workaround
[    0.835819] ehci_hcd 0000:00:13.5: debug port 1
[    0.835883] ehci_hcd 0000:00:13.5: irq 19, io mem 0xfe029000
[    0.841023] ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00
[    0.841309] hub 1-0:1.0: USB hub found
[    0.841343] hub 1-0:1.0: 10 ports detected
[    0.841527] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.841596] ohci_hcd 0000:00:13.0: OHCI Host Controller
[    0.841638] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
[    0.841726] ohci_hcd 0000:00:13.0: irq 16, io mem 0xfe02e000
[    0.896247] hub 2-0:1.0: USB hub found
[    0.896282] hub 2-0:1.0: 2 ports detected
[    0.896386] ohci_hcd 0000:00:13.1: OHCI Host Controller
[    0.896429] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
[    0.896515] ohci_hcd 0000:00:13.1: irq 17, io mem 0xfe02d000
[    0.951240] hub 3-0:1.0: USB hub found
[    0.953009] hub 3-0:1.0: 2 ports detected
[    0.954826] ohci_hcd 0000:00:13.2: OHCI Host Controller
[    0.956591] ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4
[    0.958365] ohci_hcd 0000:00:13.2: irq 18, io mem 0xfe02c000
[    1.015242] hub 4-0:1.0: USB hub found
[    1.016984] hub 4-0:1.0: 2 ports detected
[    1.018772] ohci_hcd 0000:00:13.3: OHCI Host Controller
[    1.020537] ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 5
[    1.022346] ohci_hcd 0000:00:13.3: irq 17, io mem 0xfe02b000
[    1.079252] hub 5-0:1.0: USB hub found
[    1.080925] hub 5-0:1.0: 2 ports detected
[    1.082754] ohci_hcd 0000:00:13.4: OHCI Host Controller
[    1.084523] ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 6
[    1.086322] ohci_hcd 0000:00:13.4: irq 18, io mem 0xfe02a000
[    1.143028] usb 1-3: new high-speed USB device number 2 using ehci_hcd
[    1.143252] hub 6-0:1.0: USB hub found
[    1.143260] hub 6-0:1.0: 2 ports detected
[    1.143525] i8042: PNP: No PS/2 controller found. Probing ports directly.
[    1.143978] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.143983] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.144220] mousedev: PS/2 mouse device common for all mice
[    1.144450] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
[    1.144564] md: linear personality registered for level -1
[    1.158755] device-mapper: uevent: version 1.0.3
[    1.160668] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected]
[    1.162540] usbcore: registered new interface driver btusb
[    1.164313] cpuidle: using governor ladder
[    1.166130] cpuidle: using governor menu
[    1.168397] ALSA device list:
[    1.170193]   No soundcards found.
[    1.171953] TCP cubic registered
[    1.173781] NET: Registered protocol family 10
[    1.175735] NET: Registered protocol family 17
[    1.177491] Bridge firewalling registered
[    1.179277] Bluetooth: RFCOMM TTY layer initialized
[    1.180977] Bluetooth: RFCOMM socket layer initialized
[    1.182769] Bluetooth: RFCOMM ver 1.11
[    1.184554] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    1.186338] Bluetooth: BNEP filters: protocol multicast
[    1.188111] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    1.189953] 8021q: 802.1Q VLAN Support v1.8
[    1.191910] PM: Checking hibernation image partition /dev/sda2
[    1.309022] ata4: softreset failed (device not ready)
[    1.310741] ata4: applying PMP SRST workaround and retrying
[    1.312429] ata3: softreset failed (device not ready)
[    1.314065] ata3: applying PMP SRST workaround and retrying
[    1.315762] ata1: softreset failed (device not ready)
[    1.317498] ata1: applying PMP SRST workaround and retrying
[    1.319217] ata2: softreset failed (device not ready)
[    1.320928] ata2: applying PMP SRST workaround and retrying
[    1.473036] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.474818] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.476574] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.478232] ata4.00: ATAPI: TSSTcorp CDDVDW SH-S203P, SB00, max UDMA/100
[    1.479949] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd
[    1.481558] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.483860] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd
[    1.485565] ata4.00: configured for UDMA/100
[    1.487445] ata2.00: ATA-8: WDC WD15EADS-00P8B0, 01.00A01, max UDMA/133
[    1.489196] ata2.00: 2930277168 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
[    1.490948] ata2.00: SB600 AHCI: limiting to 255 sectors per cmd
[    1.496101] ata2.00: SB600 AHCI: limiting to 255 sectors per cmd
[    1.497742] ata2.00: configured for UDMA/133
[    1.499609] ata1.00: ATA-8: SAMSUNG HD501LJ, CR100-11, max UDMA7
[    1.501364] ata1.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
[    1.503116] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[    1.504975] ata3.00: ATA-8: WDC WD3200BEVT-00ZCT0, 11.01A11, max UDMA/133
[    1.506724] ata3.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[    1.508508] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
[    1.510425] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[    1.512150] ata1.00: configured for UDMA/133
[    1.513976] scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HD501LJ  CR10 PQ: 0 ANSI: 5
[    1.514166] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
[    1.514168] ata3.00: configured for UDMA/133
[    1.519607] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[    1.521549] scsi 1:0:0:0: Direct-Access     ATA      WDC WD15EADS-00P 01.0 PQ: 0 ANSI: 5
[    1.521559] sd 0:0:0:0: [sda] Write Protect is off
[    1.521562] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.521578] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.527299] sd 1:0:0:0: [sdb] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
[    1.529178] sd 1:0:0:0: [sdb] Write Protect is off
[    1.529275] scsi 2:0:0:0: Direct-Access     ATA      WDC WD3200BEVT-0 11.0 PQ: 0 ANSI: 5
[    1.529521] sd 2:0:0:0: [sdc] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[    1.529560] sd 2:0:0:0: [sdc] Write Protect is off
[    1.529562] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[    1.529580] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.530467] scsi 3:0:0:0: CD-ROM            TSSTcorp CDDVDW SH-S203P  SB00 PQ: 0 ANSI: 5
[    1.532395] sr0: scsi3-mmc drive: 8x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.532397] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.532538] sr 3:0:0:0: Attached scsi CD-ROM sr0
[    1.541566]  sda: sda1 sda2 sda3 sda4
[    1.545999] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    1.546031] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.546295] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.560610]  sdb: sdb1 sdb2 sdb3 sdb4
[    1.562828] sd 1:0:0:0: [sdb] Attached SCSI disk
[    1.597293]  sdc: sdc1 sdc2 sdc3 sdc4 < sdc5 sdc6 sdc7 sdc8 >
[    1.600228] sd 2:0:0:0: [sdc] Attached SCSI disk
[    1.602242] PM: Hibernation image partition 8:2 present
[    1.602244] PM: Looking for hibernation image.
[    1.602378] PM: Image not found (code -22)
[    1.602380] PM: Hibernation image not present or could not be loaded.
[    1.602388] registered taskstats version 1
[    1.604688] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.606693] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 5600+ (2 cpu cores) (version 2.20.00)
[    1.608823] powernow-k8: fid 0x14 (2800 MHz), vid 0x8
[    1.610873] powernow-k8: fid 0x12 (2600 MHz), vid 0xa
[    1.612849] powernow-k8: fid 0x10 (2400 MHz), vid 0xc
[    1.614800] powernow-k8: fid 0xe (2200 MHz), vid 0xe
[    1.616810] powernow-k8: fid 0xc (2000 MHz), vid 0x10
[    1.618809] powernow-k8: fid 0xa (1800 MHz), vid 0x10
[    1.620776] powernow-k8: fid 0x2 (1000 MHz), vid 0x12
[    1.622869] md: Skipping autodetection of RAID arrays. (raid=autodetect will force)
[    1.648118] kjournald starting.  Commit interval 5 seconds
[    1.648148] EXT3-fs (sda3): mounted filesystem with writeback data mode
[    1.648165] VFS: Mounted root (ext3 filesystem) readonly on device 8:3.
[    1.654755] Freeing unused kernel memory: 456k freed
[    1.657047] Write protecting the kernel read-only data: 8192k
[    1.662058] Freeing unused kernel memory: 1024k freed
[    1.673039] usb 3-2: new full-speed USB device number 2 using ohci_hcd
[    2.075047] usb 5-1: new low-speed USB device number 2 using ohci_hcd
[    3.986226] udevd[871]: starting version 171
[    5.003771] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    5.003859] sd 1:0:0:0: Attached scsi generic sg1 type 0
[    5.003945] sd 2:0:0:0: Attached scsi generic sg2 type 0
[    5.004051] sr 3:0:0:0: Attached scsi generic sg3 type 5
[    5.137890] input: PC Speaker as /devices/platform/pcspkr/input/input2
[    5.166303] rtc_cmos 00:03: RTC can wake from S4
[    5.166425] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    5.166460] rtc0: alarms up to one month, 242 bytes nvram
[    5.227481] atiixp 0000:00:14.1: IDE controller (0x1002:0x438c rev 0x00)
[    5.227511] atiixp 0000:00:14.1: not 100% native mode: will probe irqs later
[    5.227517]     ide0: BM-DMA at 0xf900-0xf907
[    5.227523] Probing IDE interface ide0...
[    5.323772] input: iMON Panel, Knob and Mouse(15c2:ffdc) as /devices/pci0000:00/0000:00:13.3/usb5/5-1/5-1:1.0/input/input3
[    5.330528] IR RC5(x) protocol handler initialized
[    5.345028] imon 5-1:1.0: 0xffdc iMON VFD, MCE IR (id 0x9e)
[    5.356252] IR RC6 protocol handler initialized
[    5.488675] IR MCE Keyboard/mouse protocol handler initialized
[    5.500657] IT8716 SuperIO detected.
[    5.501152] parport_pc 00:09: reported by Plug and Play ACPI
[    5.501198] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
[    5.514421] lirc_dev: IR Remote Control driver registered, major 252
[    5.521282] IR LIRC bridge handler initialized
[    5.534033] Registered IR keymap rc-imon-mce
[    5.534336] input: iMON Remote (15c2:ffdc) as /devices/pci0000:00/0000:00:13.3/usb5/5-1/5-1:1.0/rc/rc0/input4
[    5.534437] rc0: iMON Remote (15c2:ffdc) as /devices/pci0000:00/0000:00:13.3/usb5/5-1/5-1:1.0/rc/rc0
[    5.545139] imon 5-1:1.0: iMON device (15c2:ffdc, intf0) on usb<5:2> initialized
[    5.545196] usbcore: registered new interface driver imon
[    5.679564] Linux video capture interface: v2.00
[    5.742627] saa7130/34: v4l2 driver version 0, 2, 17 loaded
[    5.742791] saa7133[0]: found at 0000:03:06.0, rev: 209, irq: 21, latency: 64, mmio: 0xfdeff000
[    5.742807] saa7133[0]: subsystem: 11bd:002f, board: Pinnacle PCTV 310i [card=101,autodetected]
[    5.742852] saa7133[0]: board init: gpio is 600c000
[    5.743251] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[    5.743445] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[    5.752592] uvcvideo: Unable to create debugfs directory
[    5.773782] usbcore: registered new interface driver snd-usb-audio
[    5.773797] uvcvideo: Found UVC 1.00 device VF0700 Live! Cam Chat HD (041e:4088)
[    5.778989] input: VF0700 Live! Cam Chat HD as /devices/pci0000:00/0000:00:13.5/usb1/1-3/1-3:1.0/input/input5
[    5.779228] usbcore: registered new interface driver uvcvideo
[    5.779234] USB Video Class driver (1.1.1)
[    5.845168] saa7133[0]: i2c eeprom read error (err=-5)
[    6.030890] hda_codec: ALC883: BIOS auto-probing.
[    6.052822] input: HDA ATI SB Line as /devices/pci0000:00/0000:00:14.2/sound/card1/input6
[    6.053095] input: HDA ATI SB Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input7
[    6.053321] input: HDA ATI SB Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input8
[    6.053550] input: HDA ATI SB Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card1/input9
[    6.053785] input: HDA ATI SB Line Out as /devices/pci0000:00/0000:00:14.2/sound/card1/input10
[    6.055663] snd_hda_intel 0000:01:05.2: irq 42 for MSI/MSI-X
[    6.062440] i2c-core: driver [tuner] using legacy suspend method
[    6.062447] i2c-core: driver [tuner] using legacy resume method
[    6.149032] tuner 5-004b: Tuner -1 found with type(s) Radio TV.
[    6.184028] tda829x 5-004b: setting tuner address to 61
[    6.435025] tda829x 5-004b: type set to tda8290+75a
[    9.067029] hda-intel: azx_get_response timeout, switching to polling mode: last cmd=0x000f0000
[    9.456159] saa7133[0]: registered device video1 [v4l2]
[    9.456234] saa7133[0]: registered device vbi0
[    9.456305] saa7133[0]: registered device radio0
[    9.510095] dvb_init() allocating 1 frontend
[    9.532052] DVB: registering new adapter (saa7133[0])
[    9.532064] DVB: registering adapter 0 frontend 0 (Philips TDA10046H DVB-T)...
[    9.574037] tda1004x: setting up plls for 48MHz sampling clock
[    9.780038] tda1004x: found firmware revision 0 -- invalid
[    9.780048] tda1004x: trying to boot from eeprom
[   10.068029] hda-intel: No response from codec, disabling MSI: last cmd=0x000f0000
[   11.069045] hda-intel: Codec #0 probe error; disabling it...
[   12.087023] tda1004x: timeout waiting for DSP ready
[   12.097024] tda1004x: found firmware revision 0 -- invalid
[   12.097029] tda1004x: waiting for firmware upload...
[   13.180031] hda_intel: azx_get_response timeout, switching to single_cmd mode: last cmd=0x00070503
[   13.185372] hda-codec: No codec parser is available
[   19.706153] EXT3-fs (sda3): using internal journal
[   19.904880] kjournald starting.  Commit interval 5 seconds
[   19.905091] EXT3-fs (sda1): using internal journal
[   19.905098] EXT3-fs (sda1): mounted filesystem with writeback data mode
[   19.939997] kjournald starting.  Commit interval 5 seconds
[   19.940128] EXT3-fs (dm-2): using internal journal
[   19.940134] EXT3-fs (dm-2): mounted filesystem with writeback data mode
[   20.028599] kjournald starting.  Commit interval 5 seconds
[   20.028823] EXT3-fs (dm-3): using internal journal
[   20.028830] EXT3-fs (dm-3): mounted filesystem with writeback data mode
[   20.052466] kjournald starting.  Commit interval 5 seconds
[   20.052772] EXT3-fs (dm-4): using internal journal
[   20.052778] EXT3-fs (dm-4): mounted filesystem with writeback data mode
[   20.099494] EXT4-fs (dm-5): mounted filesystem with ordered data mode. Opts: (null)
[   20.223180] EXT4-fs (dm-8): mounted filesystem with ordered data mode. Opts: (null)
[   20.254644] kjournald starting.  Commit interval 5 seconds
[   20.254973] EXT3-fs (dm-6): using internal journal
[   20.254980] EXT3-fs (dm-6): mounted filesystem with writeback data mode
[   20.304321] EXT4-fs (dm-7): mounted filesystem with ordered data mode. Opts: (null)
[   20.368320] EXT4-fs (dm-0): mounted filesystem without journal. Opts: (null)
[   20.477077] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
[   22.181037] tda1004x: timeout waiting for DSP ready
[   22.191051] tda1004x: found firmware revision 0 -- invalid
[   22.191059] tda1004x: firmware upload failed
[   22.316459] saa7134 ALSA driver for DMA sound loaded
[   22.316521] saa7133[0]/alsa: saa7133[0] at 0xfdeff000 irq 21 registered as card -1
[   22.954074] Adding 10490440k swap on /dev/sda2.  Priority:-1 extents:1 across:10490440k
[   24.137485] r8169 0000:02:00.0: eth0: link down
[   24.138371] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   24.636526] ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   25.888644] r8169 0000:02:00.0: eth0: link up
[   25.889461] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   25.890216] ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   32.921380] input: lircmd as /devices/virtual/input/input11
[   36.226025] eth0.2: no IPv6 routers present
[   36.810028] eth0: no IPv6 routers present
[   37.025048] input: iMON Panel, Knob and Mouse(15c2:ffdc) (lircd bypass) as /devices/virtual/input/input12

dmesg, patched:

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.3.8-dirty (anders@tv) (gcc version 4.5.3 (Gentoo 4.5.3-r2 p1.1, pie-0.4.7) ) #68 SMP PREEMPT Fri Jul 6 19:39:29 CEST 2012
[    0.000000] Command line: root=/dev/sda3 hpet=disable crashkernel=128M
[    0.000000] KERNEL supported cpus:
[    0.000000]   AMD AuthenticAMD
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[    0.000000]  BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 0000000077ee0000 (usable)
[    0.000000]  BIOS-e820: 0000000077ee0000 - 0000000077ee3000 (ACPI NVS)
[    0.000000]  BIOS-e820: 0000000077ee3000 - 0000000077ef0000 (ACPI data)
[    0.000000]  BIOS-e820: 0000000077ef0000 - 0000000077f00000 (reserved)
[    0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] DMI 2.4 present.
[    0.000000] DMI: System manufacturer System Product Name/M2A-VM HDMI, BIOS ASUS M2A-VM HDMI ACPI BIOS Revision 2201 10/22/2008
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] No AGP bridge found
[    0.000000] last_pfn = 0x77ee0 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-C7FFF write-protect
[    0.000000]   C8000-FFFFF uncachable
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 0000000000 mask FFC0000000 write-back
[    0.000000]   1 base 0040000000 mask FFE0000000 write-back
[    0.000000]   2 base 0060000000 mask FFF0000000 write-back
[    0.000000]   3 base 0070000000 mask FFF8000000 write-back
[    0.000000]   4 base 0077F00000 mask FFFFF00000 uncachable
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] found SMP MP-table at [ffff8800000f6560] f6560
[    0.000000] initial memory mapped : 0 - 20000000
[    0.000000] Base memory trampoline at [ffff88000009a000] 9a000 size 20480
[    0.000000] init_memory_mapping: 0000000000000000-0000000077ee0000
[    0.000000]  0000000000 - 0077e00000 page 2M
[    0.000000]  0077e00000 - 0077ee0000 page 4k
[    0.000000] kernel direct mapping tables up to 77ee0000 @ 1fffc000-20000000
[    0.000000] Reserving 128MB of memory at 768MB for crashkernel (System RAM: 1918MB)
[    0.000000] ACPI: RSDP 00000000000f8210 00024 (v02 ATI   )
[    0.000000] ACPI: XSDT 0000000077ee3100 00044 (v01 ATI    ASUSACPI 42302E31 AWRD 00000000)
[    0.000000] ACPI: FACP 0000000077ee8500 000F4 (v03 ATI    ASUSACPI 42302E31 AWRD 00000000)
[    0.000000] ACPI: DSDT 0000000077ee3280 05210 (v01 ATI    ASUSACPI 00001000 MSFT 03000000)
[    0.000000] ACPI: FACS 0000000077ee0000 00040
[    0.000000] ACPI: SSDT 0000000077ee8740 002CC (v01 PTLTD  POWERNOW 00000001  LTP 00000001)
[    0.000000] ACPI: MCFG 0000000077ee8b00 0003C (v01 ATI    ASUSACPI 42302E31 AWRD 00000000)
[    0.000000] ACPI: APIC 0000000077ee8640 00084 (v01 ATI    ASUSACPI 42302E31 AWRD 00000000)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000]  [ffffea0000000000-ffffea0001bfffff] PMD -> [ffff880075800000-ffff8800773fffff] on node 0
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   empty
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x00077ee0
[    0.000000] On node 0 totalpages: 491119
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 5 pages reserved
[    0.000000]   DMA zone: 3922 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 6661 pages used for memmap
[    0.000000]   DMA32 zone: 480475 pages, LIFO batch:31
[    0.000000] Detected use of extended apic ids on hypertransport bus
[    0.000000] ACPI: PM-Timer IO Port: 0x4008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[    0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at 77f00000 (gap: 77f00000:68100000)
[    0.000000] setup_percpu: NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 25 pages/cpu @ffff880077c00000 s71424 r8192 d22784 u524288
[    0.000000] pcpu-alloc: s71424 r8192 d22784 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 484397
[    0.000000] Kernel command line: root=/dev/sda3 hpet=disable crashkernel=128M
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Node 0: aperture @ 1066000000 size 32 MB
[    0.000000] Aperture beyond 4GB. Ignoring.
[    0.000000] Memory: 1791420k/1964928k available (5100k kernel code, 452k absent, 173056k reserved, 3466k data, 456k init)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  CONFIG_RCU_FANOUT set to non-default value of 32
[    0.000000] NR_IRQS:4352 nr_irqs:712 16
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] allocated 7864320 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 2799.805 MHz processor.
[    0.000000] Marking TSC unstable due to TSCs unsynchronized
[    0.002039] Calibrating delay loop (skipped), value calculated using timer frequency.. 5599.61 BogoMIPS (lpj=2799805)
[    0.002110] pid_max: default: 32768 minimum: 301
[    0.002216] Mount-cache hash table entries: 256
[    0.003098] Initializing cgroup subsys cpuacct
[    0.003134] Initializing cgroup subsys memory
[    0.003180] Initializing cgroup subsys devices
[    0.003214] Initializing cgroup subsys freezer
[    0.003250] Initializing cgroup subsys blkio
[    0.003313] tseg: 0077f00000
[    0.003315] CPU: Physical Processor ID: 0
[    0.003349] CPU: Processor Core ID: 0
[    0.003384] mce: CPU supports 5 MCE banks
[    0.003427] using AMD E400 aware idle routine
[    0.003490] ACPI: Core revision 20120111
[    0.006669] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.016866] CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 5600+ stepping 03
[    0.016998] Performance Events: AMD PMU driver.
[    0.016998] ... version:                0
[    0.016998] ... bit width:              48
[    0.016998] ... generic registers:      4
[    0.016998] ... value mask:             0000ffffffffffff
[    0.016998] ... max period:             00007fffffffffff
[    0.016998] ... fixed-purpose events:   0
[    0.016998] ... event mask:             000000000000000f
[    0.028011] Booting Node   0, Processors  #1
[    0.028072] smpboot cpu 1: start_ip = 9a000
[    0.099086] Brought up 2 CPUs
[    0.099121] Total of 2 processors activated (11198.38 BogoMIPS).
[    0.099618] PM: Registering ACPI NVS region at 77ee0000 (12288 bytes)
[    0.100060] NET: Registered protocol family 16
[    0.100113] node 0 link 0: io port [c000, ffff]
[    0.100113] TOM: 0000000080000000 aka 2048M
[    0.100113] node 0 link 0: mmio [a0000, bffff]
[    0.100113] node 0 link 0: mmio [80000000, dfffffff]
[    0.100113] node 0 link 0: mmio [f0000000, fe02ffff]
[    0.100113] node 0 link 0: mmio [e0000000, e03fffff]
[    0.100113] bus: [00, 03] on node 0 link 0
[    0.100113] bus: 00 index 0 [io  0x0000-0xffff]
[    0.100113] bus: 00 index 1 [mem 0x000a0000-0x000bffff]
[    0.100113] bus: 00 index 2 [mem 0x80000000-0xefffffff]
[    0.100113] bus: 00 index 3 [mem 0xf0000000-0xfcffffffff]
[    0.100113] ACPI: bus type pci registered
[    0.100126] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.100126] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[    0.118729] PCI: Using configuration type 1 for base access
[    0.126035] bio: create slab <bio-0> at 0
[    0.126133] ACPI: Added _OSI(Module Device)
[    0.126133] ACPI: Added _OSI(Processor Device)
[    0.126133] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.126133] ACPI: Added _OSI(Processor Aggregator Device)
[    0.127170] ACPI: EC: Look up EC in DSDT
[    0.130793] ACPI: Interpreter enabled
[    0.130833] ACPI: (supports S0 S1 S3 S4 S5)
[    0.131029] ACPI: Using IOAPIC for interrupt routing
[    0.136087] ACPI: No dock devices found.
[    0.136126] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.136218] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.136323] pci_root PNP0A03:00: host bridge window [io  0x0000-0x0cf7]
[    0.136359] pci_root PNP0A03:00: host bridge window [io  0x0d00-0xffff]
[    0.136395] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
[    0.136435] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000dffff]
[    0.136474] pci_root PNP0A03:00: host bridge window [mem 0x80000000-0xfebfffff]
[    0.137057] PCI host bridge to bus 0000:00
[    0.137057] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.137073] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff]
[    0.137109] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.137144] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff]
[    0.137180] pci_bus 0000:00: root bus resource [mem 0x80000000-0xfebfffff]
[    0.137224] pci 0000:00:00.0: [1002:7910] type 0 class 0x000600
[    0.137249] pci 0000:00:01.0: [1002:7912] type 1 class 0x000604
[    0.137285] pci 0000:00:07.0: [1002:7917] type 1 class 0x000604
[    0.137314] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
[    0.137344] pci 0000:00:12.0: [1002:4380] type 0 class 0x000101
[    0.137362] pci 0000:00:12.0: reg 10: [io  0xff00-0xff07]
[    0.137373] pci 0000:00:12.0: reg 14: [io  0xfe00-0xfe03]
[    0.137383] pci 0000:00:12.0: reg 18: [io  0xfd00-0xfd07]
[    0.137393] pci 0000:00:12.0: reg 1c: [io  0xfc00-0xfc03]
[    0.137403] pci 0000:00:12.0: reg 20: [io  0xfb00-0xfb0f]
[    0.137414] pci 0000:00:12.0: reg 24: [mem 0xfe02f000-0xfe02f3ff]
[    0.137435] pci 0000:00:12.0: set SATA to AHCI mode
[    0.137508] pci 0000:00:13.0: [1002:4387] type 0 class 0x000c03
[    0.137523] pci 0000:00:13.0: reg 10: [mem 0xfe02e000-0xfe02efff]
[    0.137590] pci 0000:00:13.1: [1002:4388] type 0 class 0x000c03
[    0.137605] pci 0000:00:13.1: reg 10: [mem 0xfe02d000-0xfe02dfff]
[    0.137673] pci 0000:00:13.2: [1002:4389] type 0 class 0x000c03
[    0.137687] pci 0000:00:13.2: reg 10: [mem 0xfe02c000-0xfe02cfff]
[    0.137755] pci 0000:00:13.3: [1002:438a] type 0 class 0x000c03
[    0.137769] pci 0000:00:13.3: reg 10: [mem 0xfe02b000-0xfe02bfff]
[    0.137840] pci 0000:00:13.4: [1002:438b] type 0 class 0x000c03
[    0.137854] pci 0000:00:13.4: reg 10: [mem 0xfe02a000-0xfe02afff]
[    0.138006] pci 0000:00:13.5: [1002:4386] type 0 class 0x000c03
[    0.138026] pci 0000:00:13.5: reg 10: [mem 0xfe029000-0xfe0290ff]
[    0.138113] pci 0000:00:13.5: supports D1 D2
[    0.138115] pci 0000:00:13.5: PME# supported from D0 D1 D2 D3hot
[    0.138140] pci 0000:00:14.0: [1002:4385] type 0 class 0x000c05
[    0.138163] pci 0000:00:14.0: reg 10: [io  0x0b00-0x0b0f]
[    0.138250] pci 0000:00:14.1: [1002:438c] type 0 class 0x000101
[    0.138264] pci 0000:00:14.1: reg 10: [io  0x0000-0x0007]
[    0.138274] pci 0000:00:14.1: reg 14: [io  0x0000-0x0003]
[    0.138285] pci 0000:00:14.1: reg 18: [io  0x0000-0x0007]
[    0.138295] pci 0000:00:14.1: reg 1c: [io  0x0000-0x0003]
[    0.138306] pci 0000:00:14.1: reg 20: [io  0xf900-0xf90f]
[    0.138346] pci 0000:00:14.2: [1002:4383] type 0 class 0x000403
[    0.138369] pci 0000:00:14.2: reg 10: [mem 0xfe020000-0xfe023fff 64bit]
[    0.138438] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[    0.138455] pci 0000:00:14.3: [1002:438d] type 0 class 0x000601
[    0.138533] pci 0000:00:14.4: [1002:4384] type 1 class 0x000604
[    0.138581] pci 0000:00:18.0: [1022:1100] type 0 class 0x000600
[    0.138598] pci 0000:00:18.1: [1022:1101] type 0 class 0x000600
[    0.138612] pci 0000:00:18.2: [1022:1102] type 0 class 0x000600
[    0.138628] pci 0000:00:18.3: [1022:1103] type 0 class 0x000600
[    0.138669] pci 0000:01:05.0: [1002:791e] type 0 class 0x000300
[    0.138678] pci 0000:01:05.0: reg 10: [mem 0xf0000000-0xf7ffffff 64bit pref]
[    0.138684] pci 0000:01:05.0: reg 18: [mem 0xfdbe0000-0xfdbeffff 64bit]
[    0.138689] pci 0000:01:05.0: reg 20: [io  0xde00-0xdeff]
[    0.138693] pci 0000:01:05.0: reg 24: [mem 0xfda00000-0xfdafffff]
[    0.138708] pci 0000:01:05.0: supports D1 D2
[    0.138718] pci 0000:01:05.2: [1002:7919] type 0 class 0x000403
[    0.138726] pci 0000:01:05.2: reg 10: [mem 0xfdbfc000-0xfdbfffff 64bit]
[    0.138762] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.138799] pci 0000:00:01.0:   bridge window [io  0xd000-0xdfff]
[    0.138802] pci 0000:00:01.0:   bridge window [mem 0xfda00000-0xfdbfffff]
[    0.138806] pci 0000:00:01.0:   bridge window [mem 0xf0000000-0xf7ffffff 64bit pref]
[    0.138845] pci 0000:02:00.0: [10ec:8168] type 0 class 0x000200
[    0.138860] pci 0000:02:00.0: reg 10: [io  0xee00-0xeeff]
[    0.138884] pci 0000:02:00.0: reg 18: [mem 0xfdfff000-0xfdffffff 64bit]
[    0.138912] pci 0000:02:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[    0.138973] pci 0000:02:00.0: supports D1 D2
[    0.138975] pci 0000:02:00.0: PME# supported from D1 D2 D3hot D3cold
[    0.139017] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.139064] pci 0000:00:07.0: PCI bridge to [bus 02-02]
[    0.139100] pci 0000:00:07.0:   bridge window [io  0xe000-0xefff]
[    0.139103] pci 0000:00:07.0:   bridge window [mem 0xfdf00000-0xfdffffff]
[    0.139107] pci 0000:00:07.0:   bridge window [mem 0xfdc00000-0xfdcfffff 64bit pref]
[    0.139142] pci 0000:03:06.0: [1131:7133] type 0 class 0x000480
[    0.139165] pci 0000:03:06.0: reg 10: [mem 0xfdeff000-0xfdeff7ff]
[    0.139266] pci 0000:03:06.0: supports D1 D2
[    0.139289] pci 0000:03:07.0: [1106:3044] type 0 class 0x000c00
[    0.139313] pci 0000:03:07.0: reg 10: [mem 0xfdefe000-0xfdefe7ff]
[    0.139326] pci 0000:03:07.0: reg 14: [io  0xcf00-0xcf7f]
[    0.139422] pci 0000:03:07.0: supports D2
[    0.139424] pci 0000:03:07.0: PME# supported from D2 D3hot D3cold
[    0.139473] pci 0000:00:14.4: PCI bridge to [bus 03-03] (subtractive decode)
[    0.139511] pci 0000:00:14.4:   bridge window [io  0xc000-0xcfff]
[    0.139516] pci 0000:00:14.4:   bridge window [mem 0xfde00000-0xfdefffff]
[    0.139521] pci 0000:00:14.4:   bridge window [mem 0xfdd00000-0xfddfffff pref]
[    0.139523] pci 0000:00:14.4:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.139526] pci 0000:00:14.4:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.139529] pci 0000:00:14.4:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.139532] pci 0000:00:14.4:   bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[    0.139534] pci 0000:00:14.4:   bridge window [mem 0x80000000-0xfebfffff] (subtractive decode)
[    0.139546] pci_bus 0000:00: on NUMA node 0
[    0.139548] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.139698] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[    0.139769] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE7._PRT]
[    0.139796] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[    0.139825]  pci0000:00: Requesting ACPI _OSC control (0x1d)
[    0.139861]  pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
[    0.139901] ACPI _OSC control for PCIe not granted, disabling ASPM
[    0.154036] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[    0.154429] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[    0.154820] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[    0.155318] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[    0.155709] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[    0.156112] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[    0.156504] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 *11)
[    0.156833] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[    0.157228] vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks=none
[    0.157228] vgaarb: loaded
[    0.157228] vgaarb: bridge control possible 0000:01:05.0
[    0.157228] SCSI subsystem initialized
[    0.157228] libata version 3.00 loaded.
[    0.157228] usbcore: registered new interface driver usbfs
[    0.157997] usbcore: registered new interface driver hub
[    0.158037] usbcore: registered new device driver usb
[    0.158049] Advanced Linux Sound Architecture Driver Version 1.0.24.
[    0.158049] PCI: Using ACPI for IRQ routing
[    0.167425] PCI: pci_cache_line_size set to 64 bytes
[    0.167512] reserve RAM buffer: 000000000009f000 - 000000000009ffff
[    0.167514] reserve RAM buffer: 0000000077ee0000 - 0000000077ffffff
[    0.167533] Bluetooth: Core ver 2.16
[    0.167533] NET: Registered protocol family 31
[    0.167533] Bluetooth: HCI device and connection manager initialized
[    0.167533] Bluetooth: HCI socket layer initialized
[    0.167533] Bluetooth: L2CAP socket layer initialized
[    0.169985] Bluetooth: SCO socket layer initialized
[    0.170997] pnp: PnP ACPI init
[    0.170997] ACPI: bus type pnp registered
[    0.171109] pnp 00:00: [bus 00-ff]
[    0.171111] pnp 00:00: [io  0x0cf8-0x0cff]
[    0.171114] pnp 00:00: [io  0x0000-0x0cf7 window]
[    0.171116] pnp 00:00: [io  0x0d00-0xffff window]
[    0.171119] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    0.171121] pnp 00:00: [mem 0x000c0000-0x000dffff window]
[    0.171124] pnp 00:00: [mem 0x80000000-0xfebfffff window]
[    0.171181] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
[    0.171181] pnp 00:01: [io  0x4100-0x411f]
[    0.171181] pnp 00:01: [io  0x0228-0x022f]
[    0.171181] pnp 00:01: [io  0x040b]
[    0.171181] pnp 00:01: [io  0x04d6]
[    0.171181] pnp 00:01: [io  0x0c00-0x0c01]
[    0.171181] pnp 00:01: [io  0x0c14]
[    0.171181] pnp 00:01: [io  0x0c50-0x0c52]
[    0.171181] pnp 00:01: [io  0x0c6c-0x0c6d]
[    0.171181] pnp 00:01: [io  0x0c6f]
[    0.171181] pnp 00:01: [io  0x0cd0-0x0cd1]
[    0.171181] pnp 00:01: [io  0x0cd2-0x0cd3]
[    0.171181] pnp 00:01: [io  0x0cd4-0x0cdf]
[    0.171181] pnp 00:01: [io  0x4000-0x40fe]
[    0.171181] pnp 00:01: [io  0x4210-0x4217]
[    0.171181] pnp 00:01: [io  0x0b10-0x0b1f]
[    0.171181] pnp 00:01: [mem 0x00000000-0x00000fff window]
[    0.171181] pnp 00:01: [mem 0xfee00400-0xfee00fff window]
[    0.171181] pnp 00:01: disabling [mem 0x00000000-0x00000fff window] because it overlaps 0000:02:00.0 BAR 6 [mem 0x00000000-0x0001ffff pref]
[    0.171203] system 00:01: [io  0x4100-0x411f] has been reserved
[    0.171203] system 00:01: [io  0x0228-0x022f] has been reserved
[    0.171203] system 00:01: [io  0x040b] has been reserved
[    0.171203] system 00:01: [io  0x04d6] has been reserved
[    0.171203] system 00:01: [io  0x0c00-0x0c01] has been reserved
[    0.171203] system 00:01: [io  0x0c14] has been reserved
[    0.171219] system 00:01: [io  0x0c50-0x0c52] has been reserved
[    0.171256] system 00:01: [io  0x0c6c-0x0c6d] has been reserved
[    0.171291] system 00:01: [io  0x0c6f] has been reserved
[    0.171327] system 00:01: [io  0x0cd0-0x0cd1] has been reserved
[    0.171363] system 00:01: [io  0x0cd2-0x0cd3] has been reserved
[    0.171399] system 00:01: [io  0x0cd4-0x0cdf] has been reserved
[    0.171434] system 00:01: [io  0x4000-0x40fe] has been reserved
[    0.171470] system 00:01: [io  0x4210-0x4217] has been reserved
[    0.171506] system 00:01: [io  0x0b10-0x0b1f] has been reserved
[    0.171993] system 00:01: [mem 0xfee00400-0xfee00fff window] has been reserved
[    0.172033] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.172125] pnp 00:02: [dma 4]
[    0.172127] pnp 00:02: [io  0x0000-0x000f]
[    0.172130] pnp 00:02: [io  0x0080-0x0090]
[    0.172132] pnp 00:02: [io  0x0094-0x009f]
[    0.172134] pnp 00:02: [io  0x00c0-0x00df]
[    0.172171] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.172171] pnp 00:03: [io  0x0070-0x0073]
[    0.172171] pnp 00:03: [irq 8]
[    0.172171] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.172171] pnp 00:04: [io  0x0061]
[    0.172171] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.172171] pnp 00:05: [io  0x00f0-0x00ff]
[    0.172171] pnp 00:05: [irq 13]
[    0.172171] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.172171] pnp 00:06: [io  0x0010-0x001f]
[    0.172171] pnp 00:06: [io  0x0022-0x003f]
[    0.172171] pnp 00:06: [io  0x0044-0x005f]
[    0.172171] pnp 00:06: [io  0x0062-0x0063]
[    0.172171] pnp 00:06: [io  0x0065-0x006f]
[    0.172171] pnp 00:06: [io  0x0074-0x007f]
[    0.172171] pnp 00:06: [io  0x0091-0x0093]
[    0.172171] pnp 00:06: [io  0x00a2-0x00bf]
[    0.172171] pnp 00:06: [io  0x00e0-0x00ef]
[    0.172171] pnp 00:06: [io  0x04d0-0x04d1]
[    0.172171] pnp 00:06: [io  0x0220-0x0225]
[    0.172171] system 00:06: [io  0x04d0-0x04d1] has been reserved
[    0.172171] system 00:06: [io  0x0220-0x0225] has been reserved
[    0.172171] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.172198] pnp 00:07: [io  0x03f0-0x03f5]
[    0.172200] pnp 00:07: [io  0x03f7]
[    0.172208] pnp 00:07: [irq 6]
[    0.172210] pnp 00:07: [dma 2]
[    0.172259] pnp 00:07: Plug and Play ACPI device, IDs PNP0700 (active)
[    0.173030] pnp 00:08: [io  0x03f8-0x03ff]
[    0.173038] pnp 00:08: [irq 4]
[    0.173103] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.173256] pnp 00:09: [io  0x0378-0x037f]
[    0.173264] pnp 00:09: [irq 7]
[    0.173321] pnp 00:09: Plug and Play ACPI device, IDs PNP0400 (active)
[    0.173321] pnp 00:0a: [mem 0xe0000000-0xefffffff]
[    0.173321] system 00:0a: [mem 0xe0000000-0xefffffff] has been reserved
[    0.173321] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.173321] pnp 00:0b: [mem 0x000cd600-0x000cffff]
[    0.173321] pnp 00:0b: [mem 0x000f0000-0x000f7fff]
[    0.173321] pnp 00:0b: [mem 0x000f8000-0x000fbfff]
[    0.173321] pnp 00:0b: [mem 0x000fc000-0x000fffff]
[    0.173321] pnp 00:0b: [mem 0x77ef0000-0x77feffff]
[    0.173321] pnp 00:0b: [mem 0xfed00000-0xfed000ff]
[    0.173321] pnp 00:0b: [mem 0x77ee0000-0x77efffff]
[    0.173321] pnp 00:0b: [mem 0xffff0000-0xffffffff]
[    0.173321] pnp 00:0b: [mem 0x00000000-0x0009ffff]
[    0.173321] pnp 00:0b: [mem 0x00100000-0x77edffff]
[    0.173321] pnp 00:0b: [mem 0x77ff0000-0x7ffeffff]
[    0.173321] pnp 00:0b: [mem 0xfec00000-0xfec00fff]
[    0.173321] pnp 00:0b: [mem 0xfee00000-0xfee00fff]
[    0.173321] pnp 00:0b: [mem 0xfff80000-0xfffeffff]
[    0.174001] system 00:0b: [mem 0x000cd600-0x000cffff] has been reserved
[    0.174001] system 00:0b: [mem 0x000f0000-0x000f7fff] could not be reserved
[    0.174030] system 00:0b: [mem 0x000f8000-0x000fbfff] could not be reserved
[    0.174066] system 00:0b: [mem 0x000fc000-0x000fffff] could not be reserved
[    0.174103] system 00:0b: [mem 0x77ef0000-0x77feffff] could not be reserved
[    0.174140] system 00:0b: [mem 0xfed00000-0xfed000ff] has been reserved
[    0.174176] system 00:0b: [mem 0x77ee0000-0x77efffff] could not be reserved
[    0.174212] system 00:0b: [mem 0xffff0000-0xffffffff] has been reserved
[    0.174248] system 00:0b: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.174285] system 00:0b: [mem 0x00100000-0x77edffff] could not be reserved
[    0.174321] system 00:0b: [mem 0x77ff0000-0x7ffeffff] could not be reserved
[    0.174357] system 00:0b: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.174393] system 00:0b: [mem 0xfee00000-0xfee00fff] could not be reserved
[    0.174430] system 00:0b: [mem 0xfff80000-0xfffeffff] has been reserved
[    0.174466] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.174474] pnp: PnP ACPI: found 12 devices
[    0.174508] ACPI: ACPI bus type pnp unregistered
[    0.182882] Switching to clocksource acpi_pm
[    0.182959] PCI: max bus depth: 1 pci_try_num: 2
[    0.182979] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.182979] pci 0000:00:01.0:   bridge window [io  0xd000-0xdfff]
[    0.182979] pci 0000:00:01.0:   bridge window [mem 0xfda00000-0xfdbfffff]
[    0.182979] pci 0000:00:01.0:   bridge window [mem 0xf0000000-0xf7ffffff 64bit pref]
[    0.182979] pci 0000:02:00.0: BAR 6: assigned [mem 0xfdc00000-0xfdc1ffff pref]
[    0.182979] pci 0000:00:07.0: PCI bridge to [bus 02-02]
[    0.182979] pci 0000:00:07.0:   bridge window [io  0xe000-0xefff]
[    0.182979] pci 0000:00:07.0:   bridge window [mem 0xfdf00000-0xfdffffff]
[    0.182979] pci 0000:00:07.0:   bridge window [mem 0xfdc00000-0xfdcfffff 64bit pref]
[    0.182979] pci 0000:00:14.4: PCI bridge to [bus 03-03]
[    0.182979] pci 0000:00:14.4:   bridge window [io  0xc000-0xcfff]
[    0.182979] pci 0000:00:14.4:   bridge window [mem 0xfde00000-0xfdefffff]
[    0.182979] pci 0000:00:14.4:   bridge window [mem 0xfdd00000-0xfddfffff pref]
[    0.182979] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.182979] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.182979] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.182979] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff]
[    0.182979] pci_bus 0000:00: resource 8 [mem 0x80000000-0xfebfffff]
[    0.182979] pci_bus 0000:01: resource 0 [io  0xd000-0xdfff]
[    0.182979] pci_bus 0000:01: resource 1 [mem 0xfda00000-0xfdbfffff]
[    0.182979] pci_bus 0000:01: resource 2 [mem 0xf0000000-0xf7ffffff 64bit pref]
[    0.182979] pci_bus 0000:02: resource 0 [io  0xe000-0xefff]
[    0.182979] pci_bus 0000:02: resource 1 [mem 0xfdf00000-0xfdffffff]
[    0.182979] pci_bus 0000:02: resource 2 [mem 0xfdc00000-0xfdcfffff 64bit pref]
[    0.182979] pci_bus 0000:03: resource 0 [io  0xc000-0xcfff]
[    0.182979] pci_bus 0000:03: resource 1 [mem 0xfde00000-0xfdefffff]
[    0.182979] pci_bus 0000:03: resource 2 [mem 0xfdd00000-0xfddfffff pref]
[    0.182979] pci_bus 0000:03: resource 4 [io  0x0000-0x0cf7]
[    0.182979] pci_bus 0000:03: resource 5 [io  0x0d00-0xffff]
[    0.182979] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]
[    0.182979] pci_bus 0000:03: resource 7 [mem 0x000c0000-0x000dffff]
[    0.182979] pci_bus 0000:03: resource 8 [mem 0x80000000-0xfebfffff]
[    0.182979] NET: Registered protocol family 2
[    0.182979] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.183272] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[    0.185158] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.185689] TCP: Hash tables configured (established 262144 bind 65536)
[    0.185727] TCP reno registered
[    0.185763] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[    0.185816] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[    0.185961] NET: Registered protocol family 1
[    0.186147] RPC: Registered named UNIX socket transport module.
[    0.186193] RPC: Registered udp transport module.
[    0.186227] RPC: Registered tcp transport module.
[    0.186262] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.463080] pci 0000:01:05.0: Boot video device
[    0.463092] PCI: CLS 32 bytes, default 64
[    0.463220] kvm: Nested Virtualization enabled
[    0.464180] audit: initializing netlink socket (disabled)
[    0.464227] type=2000 audit(1347732948.463:1): initialized
[    0.465327] Installing knfsd (copyright (C) 1996 [email protected]).
[    0.465646] msgmni has been set to 3498
[    0.466119] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.466162] io scheduler noop registered
[    0.466220] io scheduler cfq registered (default)
[    0.466402] pcieport 0000:00:07.0: irq 40 for MSI/MSI-X
[    0.467042] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[    0.467085] ACPI: Power Button [PWRB]
[    0.467222] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    0.467262] ACPI: Power Button [PWRF]
[    0.467426] ACPI: Fan [FAN] (on)
[    0.469041] ACPI Warning: For \_TZ_.THRM._PSL: Return Package has no elements (empty) (20120111/nspredef-463)
[    0.469143] ACPI: [Package] has zero elements (ffff880074b409c0)
[    0.469178] ACPI: Invalid passive threshold
[    0.469443] thermal LNXTHERM:00: registered as thermal_zone0
[    0.469479] ACPI: Thermal Zone [THRM] (40 C)
[    0.469742] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.490475] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.511604] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.512070] [drm] Initialized drm 1.1.0 20060810
[    0.512162] [drm] radeon defaulting to kernel modesetting.
[    0.512198] [drm] radeon kernel modesetting enabled.
[    0.512484] [drm] initializing kernel modesetting (RS690 0x1002:0x791E 0x1043:0x826D).
[    0.512538] [drm] register mmio base: 0xFDBE0000
[    0.512572] [drm] register mmio size: 65536
[    0.514171] ATOM BIOS: ATI
[    0.514224] radeon 0000:01:05.0: VRAM: 128M 0x0000000078000000 - 0x000000007FFFFFFF (128M used)
[    0.514264] radeon 0000:01:05.0: GTT: 512M 0x0000000080000000 - 0x000000009FFFFFFF
[    0.514306] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    0.514342] [drm] Driver supports precise vblank timestamp query.
[    0.514403] [drm] radeon: irq initialized.
[    0.515085] [drm] Detected VRAM RAM=128M, BAR=128M
[    0.515124] [drm] RAM width 128bits DDR
[    0.515235] [TTM] Zone  kernel: Available graphics memory: 895710 kiB.
[    0.515275] [TTM] Initializing pool allocator.
[    0.515313] [TTM] Initializing DMA pool allocator.
[    0.515381] [drm] radeon: 128M of VRAM memory ready
[    0.515417] [drm] radeon: 512M of GTT memory ready.
[    0.515454] [drm] GART: num cpu pages 131072, num gpu pages 131072
[    0.522330] [drm] radeon: ib pool ready.
[    0.523376] [drm] radeon: 1 quad pipes, 1 z pipes initialized.
[    0.529478] [drm] PCIE GART of 512M enabled (table at 0x0000000074680000).
[    0.529532] radeon 0000:01:05.0: WB enabled
[    0.529568] [drm] fence driver on ring 0 use gpu addr 0x80000000 and cpu addr 0xffff880074b46000
[    0.529724] [drm] Loading RS690/RS740 Microcode
[    0.529940] [drm] radeon: ring at 0x0000000080001000
[    0.529989] [drm] ring test succeeded in 1 usecs
[    0.530147] [drm] ib test succeeded in 0 usecs
[    0.530935] [drm] Radeon Display Connectors
[    0.530970] [drm] Connector 0:
[    0.531013] [drm]   VGA
[    0.531047] [drm]   DDC: 0x7e50 0x7e40 0x7e54 0x7e44 0x7e58 0x7e48 0x7e5c 0x7e4c
[    0.531085] [drm]   Encoders:
[    0.531119] [drm]     CRT1: INTERNAL_KLDSCP_DAC1
[    0.531153] [drm] Connector 1:
[    0.531186] [drm]   S-video
[    0.531219] [drm]   Encoders:
[    0.531252] [drm]     TV1: INTERNAL_KLDSCP_DAC1
[    0.531286] [drm] Connector 2:
[    0.531319] [drm]   HDMI-A
[    0.531352] [drm]   HPD2
[    0.531386] [drm]   DDC: 0x7e40 0x7e60 0x7e44 0x7e64 0x7e48 0x7e68 0x7e4c 0x7e6c
[    0.531424] [drm]   Encoders:
[    0.531457] [drm]     DFP2: INTERNAL_DDI
[    0.531490] [drm] Connector 3:
[    0.531524] [drm]   DVI-D
[    0.531558] [drm]   DDC: 0x7e40 0x7e50 0x7e44 0x7e54 0x7e48 0x7e58 0x7e4c 0x7e5c
[    0.531596] [drm]   Encoders:
[    0.531629] [drm]     DFP3: INTERNAL_LVTM1
[    0.788229] [drm] fb mappable at 0xF0040000
[    0.788263] [drm] vram apper at 0xF0000000
[    0.788297] [drm] size 8294400
[    0.788330] [drm] fb depth is 24
[    0.788364] [drm]    pitch is 7680
[    0.788487] fbcon: radeondrmfb (fb0) is primary device
[    0.816877] Console: switching to colour frame buffer device 240x67
[    0.826222] fb0: radeondrmfb frame buffer device
[    0.826256] drm: registered panic notifier
[    0.826291] [drm] Initialized radeon 2.13.0 20080528 for 0000:01:05.0 on minor 0
[    0.829192] brd: module loaded
[    0.830680] loop: module loaded
[    0.830760] Uniform Multi-Platform E-IDE driver
[    0.830928] ide-gd driver 1.18
[    0.831250] ahci 0000:00:12.0: version 3.0
[    0.831301] ahci 0000:00:12.0: ASUS M2A-VM: enabling 64bit DMA
[    0.831468] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[    0.831531] ahci 0000:00:12.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc
[    0.833190] scsi0 : ahci
[    0.833520] scsi1 : ahci
[    0.833748] scsi2 : ahci
[    0.833973] scsi3 : ahci
[    0.834237] ata1: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100 irq 22
[    0.834296] ata2: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180 irq 22
[    0.834354] ata3: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200 irq 22
[    0.834411] ata4: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280 irq 22
[    0.834699] tun: Universal TUN/TAP device driver, 1.6
[    0.834738] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[    0.834874] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    0.835051] r8169 0000:02:00.0: irq 41 for MSI/MSI-X
[    0.835336] r8169 0000:02:00.0: eth0: RTL8168b/8111b at 0xffffc9000000c000, 00:1b:fc:89:fa:a2, XID 18000000 IRQ 41
[    0.835415] r8169 0000:02:00.0: eth0: jumbo features [frames: 4080 bytes, tx checksumming: ko]
[    0.835551] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.835624] ehci_hcd 0000:00:13.5: EHCI Host Controller
[    0.835670] ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 1
[    0.835748] ehci_hcd 0000:00:13.5: applying AMD SB600/SB700 USB freeze workaround
[    0.835818] ehci_hcd 0000:00:13.5: debug port 1
[    0.835882] ehci_hcd 0000:00:13.5: irq 19, io mem 0xfe029000
[    0.841024] ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00
[    0.841320] hub 1-0:1.0: USB hub found
[    0.841351] hub 1-0:1.0: 10 ports detected
[    0.841536] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.841607] ohci_hcd 0000:00:13.0: OHCI Host Controller
[    0.841649] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
[    0.841737] ohci_hcd 0000:00:13.0: irq 16, io mem 0xfe02e000
[    0.896251] hub 2-0:1.0: USB hub found
[    0.896291] hub 2-0:1.0: 2 ports detected
[    0.896439] ohci_hcd 0000:00:13.1: OHCI Host Controller
[    0.896486] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
[    0.896580] ohci_hcd 0000:00:13.1: irq 17, io mem 0xfe02d000
[    0.951252] hub 3-0:1.0: USB hub found
[    0.953016] hub 3-0:1.0: 2 ports detected
[    0.954833] ohci_hcd 0000:00:13.2: OHCI Host Controller
[    0.956599] ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4
[    0.958385] ohci_hcd 0000:00:13.2: irq 18, io mem 0xfe02c000
[    1.015230] hub 4-0:1.0: USB hub found
[    1.016980] hub 4-0:1.0: 2 ports detected
[    1.018802] ohci_hcd 0000:00:13.3: OHCI Host Controller
[    1.020562] ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 5
[    1.022370] ohci_hcd 0000:00:13.3: irq 17, io mem 0xfe02b000
[    1.079228] hub 5-0:1.0: USB hub found
[    1.080897] hub 5-0:1.0: 2 ports detected
[    1.082725] ohci_hcd 0000:00:13.4: OHCI Host Controller
[    1.084501] ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 6
[    1.086279] ohci_hcd 0000:00:13.4: irq 18, io mem 0xfe02a000
[    1.143032] usb 1-3: new high-speed USB device number 2 using ehci_hcd
[    1.143185] hub 6-0:1.0: USB hub found
[    1.143191] hub 6-0:1.0: 2 ports detected
[    1.143437] i8042: PNP: No PS/2 controller found. Probing ports directly.
[    1.150211] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.152106] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.154048] mousedev: PS/2 mouse device common for all mice
[    1.156117] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
[    1.158076] md: linear personality registered for level -1
[    1.159986] device-mapper: uevent: version 1.0.3
[    1.161805] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected]
[    1.163693] usbcore: registered new interface driver btusb
[    1.165442] cpuidle: using governor ladder
[    1.167252] cpuidle: using governor menu
[    1.169525] ALSA device list:
[    1.171312]   No soundcards found.
[    1.173092] TCP cubic registered
[    1.174949] NET: Registered protocol family 10
[    1.176904] NET: Registered protocol family 17
[    1.178629] Bridge firewalling registered
[    1.180410] Bluetooth: RFCOMM TTY layer initialized
[    1.182144] Bluetooth: RFCOMM socket layer initialized
[    1.183937] Bluetooth: RFCOMM ver 1.11
[    1.185721] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    1.187521] Bluetooth: BNEP filters: protocol multicast
[    1.189319] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    1.191179] 8021q: 802.1Q VLAN Support v1.8
[    1.193154] PM: Checking hibernation image partition /dev/sda2
[    1.294030] ata1: softreset failed (device not ready)
[    1.295711] ata1: applying PMP SRST workaround and retrying
[    1.297355] ata3: softreset failed (device not ready)
[    1.299075] ata3: applying PMP SRST workaround and retrying
[    1.300850] ata4: softreset failed (device not ready)
[    1.302563] ata4: applying PMP SRST workaround and retrying
[    1.304269] ata2: softreset failed (device not ready)
[    1.305988] ata2: applying PMP SRST workaround and retrying
[    1.458035] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.459802] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.461490] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.463265] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.464860] ata4.00: ATAPI: TSSTcorp CDDVDW SH-S203P, SB00, max UDMA/100
[    1.466559] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd
[    1.468262] ata1.00: ATA-8: SAMSUNG HD501LJ, CR100-11, max UDMA7
[    1.469961] ata1.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
[    1.471668] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[    1.473555] ata2.00: ATA-8: WDC WD15EADS-00P8B0, 01.00A01, max UDMA/133
[    1.475331] ata2.00: 2930277168 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
[    1.477072] ata2.00: SB600 AHCI: limiting to 255 sectors per cmd
[    1.478752] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd
[    1.480460] ata4.00: configured for UDMA/100
[    1.482198] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[    1.483912] ata1.00: configured for UDMA/133
[    1.485770] scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HD501LJ  CR10 PQ: 0 ANSI: 5
[    1.485983] ata2.00: SB600 AHCI: limiting to 255 sectors per cmd
[    1.485986] ata2.00: configured for UDMA/133
[    1.491337] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[    1.492329] ata3.00: ATA-8: WDC WD3200BEVT-00ZCT0, 11.01A11, max UDMA/133
[    1.492331] ata3.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[    1.492335] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
[    1.493287] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
[    1.493290] ata3.00: configured for UDMA/133
[    1.496102] scsi 1:0:0:0: Direct-Access     ATA      WDC WD15EADS-00P 01.0 PQ: 0 ANSI: 5
[    1.496315] sd 1:0:0:0: [sdb] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
[    1.496355] sd 1:0:0:0: [sdb] Write Protect is off
[    1.496358] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    1.496374] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.506240]  sdb: sdb1 sdb2 sdb3 sdb4
[    1.511092] sd 0:0:0:0: [sda] Write Protect is off
[    1.511124] scsi 2:0:0:0: Direct-Access     ATA      WDC WD3200BEVT-0 11.0 PQ: 0 ANSI: 5
[    1.511419] sd 2:0:0:0: [sdc] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[    1.511456] sd 2:0:0:0: [sdc] Write Protect is off
[    1.511458] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[    1.511474] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.520249] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.520285] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.520638] sd 1:0:0:0: [sdb] Attached SCSI disk
[    1.524200] scsi 3:0:0:0: CD-ROM            TSSTcorp CDDVDW SH-S203P  SB00 PQ: 0 ANSI: 5
[    1.528046] sr0: scsi3-mmc drive: 8x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.529903] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.530825]  sda: sda1 sda2 sda3 sda4
[    1.533742] sr 3:0:0:0: Attached scsi CD-ROM sr0
[    1.534035] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.596783]  sdc: sdc1 sdc2 sdc3 sdc4 < sdc5 sdc6 sdc7 sdc8 >
[    1.599583] sd 2:0:0:0: [sdc] Attached SCSI disk
[    1.601542] PM: Hibernation image partition 8:2 present
[    1.601544] PM: Looking for hibernation image.
[    1.601676] PM: Image not found (code -22)
[    1.601678] PM: Hibernation image not present or could not be loaded.
[    1.601687] registered taskstats version 1
[    1.603907] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.605848] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 5600+ (2 cpu cores) (version 2.20.00)
[    1.607910] powernow-k8: fid 0x14 (2800 MHz), vid 0x8
[    1.609904] powernow-k8: fid 0x12 (2600 MHz), vid 0xa
[    1.611836] powernow-k8: fid 0x10 (2400 MHz), vid 0xc
[    1.613752] powernow-k8: fid 0xe (2200 MHz), vid 0xe
[    1.615692] powernow-k8: fid 0xc (2000 MHz), vid 0x10
[    1.617646] powernow-k8: fid 0xa (1800 MHz), vid 0x10
[    1.619578] powernow-k8: fid 0x2 (1000 MHz), vid 0x12
[    1.621622] md: Skipping autodetection of RAID arrays. (raid=autodetect will force)
[    1.645665] kjournald starting.  Commit interval 5 seconds
[    1.645699] EXT3-fs (sda3): mounted filesystem with writeback data mode
[    1.645715] VFS: Mounted root (ext3 filesystem) readonly on device 8:3.
[    1.652041] Freeing unused kernel memory: 456k freed
[    1.654290] Write protecting the kernel read-only data: 8192k
[    1.659253] Freeing unused kernel memory: 1024k freed
[    1.669040] usb 3-2: new full-speed USB device number 2 using ohci_hcd
[    2.072042] usb 5-1: new low-speed USB device number 2 using ohci_hcd
[    3.979588] udevd[872]: starting version 171
[    5.070436] atiixp 0000:00:14.1: IDE controller (0x1002:0x438c rev 0x00)
[    5.070502] atiixp 0000:00:14.1: not 100% native mode: will probe irqs later
[    5.070520]     ide0: BM-DMA at 0xf900-0xf907
[    5.070534] Probing IDE interface ide0...
[    5.195189] input: PC Speaker as /devices/platform/pcspkr/input/input2
[    5.223764] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    5.223850] sd 1:0:0:0: Attached scsi generic sg1 type 0
[    5.223928] sd 2:0:0:0: Attached scsi generic sg2 type 0
[    5.224032] sr 3:0:0:0: Attached scsi generic sg3 type 5
[    5.237442] input: iMON Panel, Knob and Mouse(15c2:ffdc) as /devices/pci0000:00/0000:00:13.3/usb5/5-1/5-1:1.0/input/input3
[    5.257039] imon 5-1:1.0: 0xffdc iMON VFD, MCE IR (id 0x9e)
[    5.308271] IT8716 SuperIO detected.
[    5.309299] parport_pc 00:09: reported by Plug and Play ACPI
[    5.309344] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
[    5.348300] IR RC5(x) protocol handler initialized
[    5.391188] rtc_cmos 00:03: RTC can wake from S4
[    5.391501] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    5.391554] rtc0: alarms up to one month, 242 bytes nvram
[    5.404400] Linux video capture interface: v2.00
[    5.406857] IR RC6 protocol handler initialized
[    5.429034] Registered IR keymap rc-imon-mce
[    5.429339] input: iMON Remote (15c2:ffdc) as /devices/pci0000:00/0000:00:13.3/usb5/5-1/5-1:1.0/rc/rc0/input4
[    5.429441] rc0: iMON Remote (15c2:ffdc) as /devices/pci0000:00/0000:00:13.3/usb5/5-1/5-1:1.0/rc/rc0
[    5.441151] imon 5-1:1.0: iMON device (15c2:ffdc, intf0) on usb<5:2> initialized
[    5.441212] usbcore: registered new interface driver imon
[    5.445549] uvcvideo: Unable to create debugfs directory
[    5.583247] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[    5.583447] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[    5.587445] IR MCE Keyboard/mouse protocol handler initialized
[    5.612856] lirc_dev: IR Remote Control driver registered, major 61
[    5.617640] ir_lirc_codec: disagrees about version of symbol lirc_dev_fop_poll
[    5.617648] ir_lirc_codec: Unknown symbol lirc_dev_fop_poll (err -22)
[    5.617664] ir_lirc_codec: disagrees about version of symbol lirc_dev_fop_open
[    5.617671] ir_lirc_codec: Unknown symbol lirc_dev_fop_open (err -22)
[    5.617683] ir_lirc_codec: disagrees about version of symbol lirc_get_pdata
[    5.617689] ir_lirc_codec: Unknown symbol lirc_get_pdata (err -22)
[    5.617703] ir_lirc_codec: disagrees about version of symbol lirc_dev_fop_close
[    5.617709] ir_lirc_codec: Unknown symbol lirc_dev_fop_close (err -22)
[    5.617720] ir_lirc_codec: disagrees about version of symbol lirc_dev_fop_read
[    5.617726] ir_lirc_codec: Unknown symbol lirc_dev_fop_read (err -22)
[    5.617734] ir_lirc_codec: disagrees about version of symbol lirc_register_driver
[    5.617740] ir_lirc_codec: Unknown symbol lirc_register_driver (err -22)
[    5.617769] ir_lirc_codec: disagrees about version of symbol lirc_dev_fop_ioctl
[    5.617775] ir_lirc_codec: Unknown symbol lirc_dev_fop_ioctl (err -22)
[    5.678523] hda_codec: ALC883: BIOS auto-probing.
[    5.701422] input: HDA ATI SB Line as /devices/pci0000:00/0000:00:14.2/sound/card1/input5
[    5.701660] input: HDA ATI SB Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input6
[    5.701870] input: HDA ATI SB Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input7
[    5.702100] input: HDA ATI SB Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card1/input8
[    5.702345] input: HDA ATI SB Line Out as /devices/pci0000:00/0000:00:14.2/sound/card1/input9
[    5.704117] snd_hda_intel 0000:01:05.2: irq 42 for MSI/MSI-X
[    5.733517] usbcore: registered new interface driver snd-usb-audio
[    5.733529] uvcvideo: Found UVC 1.00 device VF0700 Live! Cam Chat HD (041e:4088)
[    5.735727] input: VF0700 Live! Cam Chat HD as /devices/pci0000:00/0000:00:13.5/usb1/1-3/1-3:1.0/input/input10
[    5.735866] usbcore: registered new interface driver uvcvideo
[    5.735871] USB Video Class driver (1.1.1)
[    5.758334] saa7130/34: v4l2 driver version 0, 2, 17 loaded
[    5.758498] saa7133[0]: found at 0000:03:06.0, rev: 209, irq: 21, latency: 64, mmio: 0xfdeff000
[    5.758514] saa7133[0]: subsystem: 11bd:002f, board: Pinnacle PCTV 310i [card=101,autodetected]
[    5.758569] saa7133[0]: board init: gpio is 600c000
[    5.861175] saa7133[0]: i2c eeprom read error (err=-5)
[    6.063369] i2c-core: driver [tuner] using legacy suspend method
[    6.063382] i2c-core: driver [tuner] using legacy resume method
[    6.487041] tuner 5-004b: Tuner -1 found with type(s) Radio TV.
[    6.523079] tda829x 5-004b: setting tuner address to 61
[    6.565254] tda829x 5-004b: ANDERS: setting switch_addr. was 0x00, new 0x4b
[    6.565265] tda829x 5-004b: ANDERS: new 0x61
[    6.571031] tda829x 5-004b: type set to tda8290+75a
[    8.715040] hda-intel: azx_get_response timeout, switching to polling mode: last cmd=0x000f0000
[    9.568135] saa7133[0]: registered device video1 [v4l2]
[    9.568213] saa7133[0]: registered device vbi0
[    9.568285] saa7133[0]: registered device radio0
[    9.597534] dvb_init() allocating 1 frontend
[    9.615047] DVB: registering new adapter (saa7133[0])
[    9.615060] DVB: registering adapter 0 frontend 0 (Philips TDA10046H DVB-T)...
[    9.667056] tda1004x: setting up plls for 48MHz sampling clock
[    9.716022] hda-intel: No response from codec, disabling MSI: last cmd=0x000f0000
[   10.717036] hda-intel: Codec #0 probe error; disabling it...
[   11.851032] tda1004x: timeout waiting for DSP ready
[   11.861026] tda1004x: found firmware revision 0 -- invalid
[   11.861032] tda1004x: trying to boot from eeprom
[   12.828031] hda_intel: azx_get_response timeout, switching to single_cmd mode: last cmd=0x00070503
[   12.833029] hda-codec: No codec parser is available
[   14.169029] tda1004x: timeout waiting for DSP ready
[   14.179024] tda1004x: found firmware revision 0 -- invalid
[   14.179047] tda1004x: waiting for firmware upload...
[   24.195035] tda1004x: timeout waiting for DSP ready
[   24.205025] tda1004x: found firmware revision 0 -- invalid
[   24.205031] tda1004x: firmware upload failed
[   24.327099] saa7134 ALSA driver for DMA sound loaded
[   24.327166] saa7133[0]/alsa: saa7133[0] at 0xfdeff000 irq 21 registered as card -1
[   86.067258] EXT3-fs (sda3): using internal journal
[   86.282706] kjournald starting.  Commit interval 5 seconds
[   86.283033] EXT3-fs (sda1): using internal journal
[   86.283057] EXT3-fs (sda1): mounted filesystem with writeback data mode
[   86.317804] kjournald starting.  Commit interval 5 seconds
[   86.318048] EXT3-fs (dm-2): using internal journal
[   86.318055] EXT3-fs (dm-2): mounted filesystem with writeback data mode
[   86.414727] kjournald starting.  Commit interval 5 seconds
[   86.415075] EXT3-fs (dm-3): using internal journal
[   86.415082] EXT3-fs (dm-3): mounted filesystem with writeback data mode
[   86.439344] kjournald starting.  Commit interval 5 seconds
[   86.439857] EXT3-fs (dm-4): using internal journal
[   86.439864] EXT3-fs (dm-4): mounted filesystem with writeback data mode
[   86.502842] EXT4-fs (dm-5): mounted filesystem with ordered data mode. Opts: (null)
[   86.664276] EXT4-fs (dm-8): mounted filesystem with ordered data mode. Opts: (null)
[   86.719547] kjournald starting.  Commit interval 5 seconds
[   86.719916] EXT3-fs (dm-6): using internal journal
[   86.719924] EXT3-fs (dm-6): mounted filesystem with writeback data mode
[   86.745408] EXT4-fs (dm-7): mounted filesystem with ordered data mode. Opts: (null)
[   86.805303] EXT4-fs (dm-0): mounted filesystem without journal. Opts: (null)
[   86.892045] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
[   89.622234] Adding 10490440k swap on /dev/sda2.  Priority:-1 extents:1 across:10490440k
[   90.770896] r8169 0000:02:00.0: eth0: link down
[   90.771780] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   91.263841] ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   92.469649] r8169 0000:02:00.0: eth0: link up
[   92.470545] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   92.471305] ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   99.765095] input: lircmd as /devices/virtual/input/input11
[  102.962022] eth0: no IPv6 routers present
[  102.962033] eth0.2: no IPv6 routers present
[  103.857743] input: iMON Panel, Knob and Mouse(15c2:ffdc) (lircd bypass) as /devices/virtual/input/input12