mx6q: Add basic support for mx6qsabreauto
PATCH 1/1 mx6q: Add basic support for mx6qsabreauto
mx6qsabreauto is a board based on mx6q SoC with the following features:
- 2GB of DDR3
- 2 USB ports
- 1 HDMI output port
- SPI NOR
- 2 LVDS LCD ports
- Gigabit Ethernet
- Camera
- eMMC and SD card slot
- Multichannel Audio
- CAN
- SATA
- NAND
- PCIE
- Video Input
Add very basic support for it.
--- MAINTAINERS | 1 + board/freescale/mx6qsabreauto/Makefile | 41 ++++++ board/freescale/mx6qsabreauto/imximage.cfg | 159 +++++++++++++++++++++++ board/freescale/mx6qsabreauto/mx6qsabreauto.c | 117 +++++++++++++++++ boards.cfg | 1 + include/configs/mx6qsabreauto.h | 166 +++++++++++++++++++++++++ 6 files changed, 485 insertions(+) create mode 100644 board/freescale/mx6qsabreauto/Makefile create mode 100644 board/freescale/mx6qsabreauto/imximage.cfg create mode 100644 board/freescale/mx6qsabreauto/mx6qsabreauto.c create mode 100644 include/configs/mx6qsabreauto.h
MAINTAINERS +1 -0
@@ -655,6 +655,7 @@ Fabio Estevam <[email protected]> mx53ard i.MX53 mx53smd i.MX53 mx6qsabresd i.MX6Q + mx6qsabreauto i.MX6Q Daniel Gorsulowski <[email protected]>
board/freescale/mx6qsabreauto/Makefile new file +41 -0
41 lines not on this page · raw message
board/freescale/mx6qsabreauto/imximage.cfg new file +159 -0
159 lines not on this page · raw message
board/freescale/mx6qsabreauto/mx6qsabreauto.c new file +117 -0
117 lines not on this page · raw message
boards.cfg +1 -0
@@ -231,6 +231,7 @@ mx53smd arm armv7 mx53smd freesca ima3-mx53 arm armv7 ima3-mx53 esg mx5 ima3-mx53:IMX_CONFIG=board/esg/ima3-mx53/imximage.cfg vision2 arm armv7 vision2 ttcontrol mx5 vision2:IMX_CONFIG=board/ttcontrol/vision2/imximage_hynix.cfg mx6qarm2 arm armv7 mx6qarm2 freescale mx6 mx6qarm2:IMX_CONFIG=board/freescale/mx6qarm2/imximage.cfg +mx6qsabreauto arm armv7 mx6qsabreauto freescale mx6 mx6qsabreauto:IMX_CONFIG=board/freescale/mx6qsabreauto/imximage.cfg mx6qsabrelite arm armv7 mx6qsabrelite freescale mx6 mx6qsabrelite:IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg mx6qsabresd arm armv7 mx6qsabresd freescale mx6 mx6qsabresd:IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg cm_t35 arm armv7 cm_t35 - omap3
include/configs/mx6qsabreauto.h new file +166 -0
166 lines not on this page · raw message
Signature · 1 line
1.7.9.5
PATCH 1/1 mx6q: Add basic support for mx6qsabreauto
Quoted 16 lines · Fabio Estevam
mx6qsabreauto is a board based on mx6q SoC with the following features:
- 2GB of DDR3
- 2 USB ports
- 1 HDMI output port
- SPI NOR
- 2 LVDS LCD ports
- Gigabit Ethernet
- Camera
- eMMC and SD card slot
- Multichannel Audio
- CAN
- SATA
- NAND
- PCIE
- Video Input
Quoted 1 line
Add very basic support for it.
Hi Fabio,
Quoted 20 lines
Signed-off-by Fabio Estevam <[email protected]>--- MAINTAINERS | 1 + board/freescale/mx6qsabreauto/Makefile | 41 ++++++ board/freescale/mx6qsabreauto/imximage.cfg | 159 +++++++++++++++++++++++ board/freescale/mx6qsabreauto/mx6qsabreauto.c | 117 +++++++++++++++++ boards.cfg | 1 + include/configs/mx6qsabreauto.h | 166 +++++++++++++++++++++++++ 6 files changed, 485 insertions(+) create mode 100644 board/freescale/mx6qsabreauto/Makefile create mode 100644 board/freescale/mx6qsabreauto/imximage.cfg create mode 100644 board/freescale/mx6qsabreauto/mx6qsabreauto.c create mode 100644 include/configs/mx6qsabreauto.hMAINTAINERS +0
-0
MAINTAINERS Fabio Estevam <[email protected]> · line 659
Quoted 5 lines
MAINTAINERS +1
-0@@ -655,6 +655,7 @@ Fabio Estevam <[email protected]> mx53ard i.MX53 mx53smd i.MX53 mx6qsabresd i.MX6Q + mx6qsabreauto i.MX6Q
I see that at least the config file is very similar to my6qsabresd. Is it only now due to a draft support or are the two boards similar ? In last case, what about to set a common include file, that both boards can include ?
Best regards,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================