rtc: omap dt support (for am33xx)
Subsystems (5)
v4 cover rtc: omap dt support (for am33xx)
Hi Andrew,
This series enhances rtc-omap driver so as to be usable on am33xx SoC by adding DT support (Beagle Bone uses am33xx). This is a revised version of series that was posted on 27th July 2012 with the subject,
"omap-am33xx rtc dt support".
It seems rtc maintainer in inactive and hence sending it you.
Please help this reach mainline.
Brief:
Enhance rtc-omap driver to make it DT capable. This is required to support boards that boot only with DT like Beagle Bone. rtc-omap driver is used in DaVinci platforms and they are also now going DT way, and these changes make their DT migration easier. rtc-omap driver is made intelligent enough to handle kicker mechanism. This also helps in removing kicker mechanism support done for DaVinci at platform level.
This series has been made over 3.7-rc1
This has been tested on Beaglebone (am33xx platform) and on DaVinci da850 evm.
Regards
Afzal
v4:
Resolve build error during module build
Improve DT documentation
v3:
Remove unit address in DT node
Use readb/writeb instead of __raw_* variants
Remove unnecessary parens
v2:
Use device name da830-rtc instead of am1808-rtc, similar change in compatible for DT
Newly added register name made similar to that existing in the driver Better commit message description
Modify Kconfig help, resolve checkpatch warning
Afzal Mohammed (4):
rtc: omap: kicker mechanism support
ARM: davinci: remove rtc kicker release
rtc: omap: dt support
rtc: omap: depend on am33xx
Vaibhav Hiremath (1):
rtc: omap: Add runtime pm support
Documentation/devicetree/bindings/rtc/rtc-omap.txt | 17 +++++ arch/arm/mach-davinci/devices-da8xx.c | 13 +--- drivers/rtc/Kconfig | 10 +-- drivers/rtc/rtc-omap.c | 80 +++++++++++++++++++++- 4 files changed, 101 insertions(+), 19 deletions(-) create mode 100644 Documentation/devicetree/bindings/rtc/rtc-omap.txt
Signature · 1 line
1.7.12
PATCH v4 1/5 rtc: omap: kicker mechanism support
OMAP RTC IP can have kicker feature. This prevents spurious writes to register. To write to registers kicker lock has to be released. Procedure to do it as follows,
1. write to kick0 register, 0x83e70b13
2. write to kick1 register, 0x95a4f1e0
Writing value other than 0x83e70b13 to kick0 enables write locking, more details about kicker mechanism can be found in section 20.3.3.5.3 of AM335X TRM @www.ti.com/am335x
Here id table information is added and is used to distinguish those that require kicker handling and the ones that doesn't need it. There are more features in the newer IP's compared to legacy ones other than kicker, which driver currently doesn't handle, supporting additional features would be easier with the addition of id table.
Older IP (of OMAP1) doesn't have revision register as per TRM, so revision register can't be relied always to find features, hence id table is being used.
While at it, replace __raw_writeb/__raw_readb with writeb/readb; this driver is used on ARMv7 (AM335X SoC)
---
v4:
Resolve build error during module build
v3:
Use readb/writeb instead of __raw_* variants
Remove unnecessary parens
v2:
Use device name da830-rtc instead of am1808-rtc
Newly added register name made similar to that existing in the driver Better commit message description
drivers/rtc/rtc-omap.c | 44 +++++++++++++++++++++++++++++++++++++++++--- 1 file changed, 41 insertions(+), 3 deletions(-)
drivers/rtc/rtc-omap.c +41 -3
@@ -38,6 +38,8 @@* the SoC). See the BOARD-SPECIFIC CUSTOMIZATION comment. */ +#define DRIVER_NAME "omap_rtc" +#define OMAP_RTC_BASE 0xfffb4800/* RTC registers */
@@ -64,6 +66,9 @@#define OMAP_RTC_COMP_MSB_REG 0x50#define OMAP_RTC_OSC_REG 0x54 +#define OMAP_RTC_KICK0_REG 0x6c +#define OMAP_RTC_KICK1_REG 0x70 +/* OMAP_RTC_CTRL_REG bit fields: */ #define OMAP_RTC_CTRL_SPLIT (1<<7)#define OMAP_RTC_CTRL_DISABLE (1<<6)
@@ -88,10 +93,18 @@#define OMAP_RTC_INTERRUPTS_IT_ALARM (1<<3)#define OMAP_RTC_INTERRUPTS_IT_TIMER (1<<2) +/* OMAP_RTC_KICKER values */ +#define KICK0_VALUE 0x83e70b13 +#define KICK1_VALUE 0x95a4f1e0 + +#define OMAP_RTC_HAS_KICKER 0x1 +static void __iomem *rtc_base; -#define rtc_read (addr) __raw_readb(rtc_base + (addr)) -#define rtc_write (val, addr) __raw_writeb(val, rtc_base + (addr)) +#define rtc_read (addr) readb(rtc_base + (addr)) +#define rtc_write (val, addr) writeb(val, rtc_base + (addr)) + +#define rtc_writel (val, addr) writel(val, rtc_base + (addr))/* we rely on the rtc framework to handle locking (rtc->ops_lock),
@@ -285,11 +298,23 @@ static struct rtc_class_ops omap_rtc_ops = {static int omap_rtc_alarm;static int omap_rtc_timer; +static struct platform_device_id omap_rtc_devtype[] = { + { + .name =DRIVER_NAME , + }, { + .name ="da830-rtc" , + .driver_data =OMAP_RTC_HAS_KICKER , + }, + {}, +}; +MODULE_DEVICE_TABLE (platform, omap_rtc_devtype); +static int __init omap_rtc_probe (struct platform_device *pdev) {struct resource *res, *mem;struct rtc_device *rtc;u8 reg, new_ctrl; +const struct platform_device_id *id_entry; omap_rtc_timer =platform_get_irq (pdev,0 );if (omap_rtc_timer <=0 ) {
@@ -322,6 +347,12 @@ static int __init omap_rtc_probe(struct platform_device *pdev) goto fail; } + id_entry =platform_get_device_id (pdev); +if (id_entry && (id_entry->driver_data &OMAP_RTC_HAS_KICKER )) { +rtc_writel (KICK0_VALUE ,OMAP_RTC_KICK0_REG ); +rtc_writel (KICK1_VALUE ,OMAP_RTC_KICK1_REG ); + } + rtc =rtc_device_register (pdev->name, &pdev->dev, &omap_rtc_ops,THIS_MODULE );if (IS_ERR (rtc)) {
@@ -398,6 +429,8 @@ fail2: fail1:rtc_device_unregister (rtc); fail0: +if (id_entry && (id_entry->driver_data &OMAP_RTC_HAS_KICKER )) +rtc_writel (0 ,OMAP_RTC_KICK0_REG );iounmap (rtc_base); fail:release_mem_region (mem->start,resource_size (mem));
@@ -408,6 +441,8 @@ static int __exit omap_rtc_remove(struct platform_device *pdev) {struct rtc_device *rtc =platform_get_drvdata (pdev);struct resource *mem =dev_get_drvdata (&rtc->dev); +const struct platform_device_id *id_entry = +platform_get_device_id (pdev);device_init_wakeup (&pdev->dev,0 );
@@ -420,6 +455,8 @@ static int __exit omap_rtc_remove(struct platform_device *pdev)free_irq (omap_rtc_alarm, rtc);rtc_device_unregister (rtc); +if (id_entry && (id_entry->driver_data &OMAP_RTC_HAS_KICKER )) +rtc_writel (0 ,OMAP_RTC_KICK0_REG );iounmap (rtc_base);release_mem_region (mem->start,resource_size (mem));return 0 ;
@@ -471,9 +508,10 @@ static struct platform_driver omap_rtc_driver = { .resume = omap_rtc_resume, .shutdown = omap_rtc_shutdown, .driver = { - .name = "omap_rtc", + .name = DRIVER_NAME, .owner = THIS_MODULE, }, + .id_table = omap_rtc_devtype, };static int __init rtc_init (void )
Signature · 1 line
1.7.12
PATCH v4 2/5 ARM: davinci: remove rtc kicker release
In reply to Afzal Mohammedrtc-omap driver is now capable of handling kicker mechanism, hence remove kicker handling at platform level, instead provide proper device name so that driver can handle kicker mechanism by itself
---
v2:
Use device name da830-rtc instead of am1808-rtc
arch/arm/mach-davinci/devices-da8xx.c | 13 +------------ 1 file changed, 1 insertion(+), 12 deletions(-)
arch/arm/mach-davinci/devices-da8xx.c +1 -12
@@ -674,7 +674,7 @@ static struct resource da8xx_rtc_resources[] = { };static struct platform_device da8xx_rtc_device = { - .name ="omap_rtc" , + .name ="da830-rtc" , .id =-1 , .num_resources =ARRAY_SIZE (da8xx_rtc_resources), .resource = da8xx_rtc_resources,
@@ -683,17 +683,6 @@ static struct platform_device da8xx_rtc_device = {int da8xx_register_rtc (void ) {int ret; -void __iomem *base; - - base =ioremap (DA8XX_RTC_BASE ,SZ_4K ); -if (WARN_ON (!base)) -return -ENOMEM ; - -/* Unlock the rtc's registers */ -__raw_writel (0x83e70b13 , base +0x6c ); -__raw_writel (0x95a4f1e0 , base +0x70 ); - -iounmap (base); ret =platform_device_register (&da8xx_rtc_device);if (!ret)
Signature · 1 line
1.7.12
PATCH v4 3/5 rtc: omap: dt support
In reply to Afzal Mohammedenhance rtc-omap driver with DT capability
---
v4:
Proper devicetree documentation
v2:
Use compatible as ti,da830-rtc instead of ti,am1808-rtc
Documentation/devicetree/bindings/rtc/rtc-omap.txt | 17 +++++++++++++++++ drivers/rtc/rtc-omap.c | 18 ++++++++++++++++++ 2 files changed, 35 insertions(+) create mode 100644 Documentation/devicetree/bindings/rtc/rtc-omap.txt
Documentation/devicetree/bindings/rtc/rtc-omap.txt new file +17 -0
@@ -0,0 +1,17 @@ +TI Real Time Clock + +Required properties: +- compatible: "ti,da830-rtc" +- reg: Address range of rtc register set +- interrupts: rtc timer, alarm interrupts in order +- interrupt-parent: phandle for the interrupt controller + +Example: + +rtc at 1c23000 { + compatible = "ti,da830-rtc"; + reg = <0x23000 0x1000>; + interrupts = <19 + 19>; + interrupt-parent = <&intc>; +};
drivers/rtc/rtc-omap.c +18 -0
@@ -20,6 +20,8 @@#include <linux/rtc.h> #include <linux/bcd.h> #include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_device.h> #include <asm/io.h>
@@ -298,6 +300,8 @@ static struct rtc_class_ops omap_rtc_ops = {static int omap_rtc_alarm;static int omap_rtc_timer; +#define OMAP_RTC_DATA_DA830_IDX 1 +static struct platform_device_id omap_rtc_devtype[] = { { .name =DRIVER_NAME ,
@@ -309,12 +313,25 @@ static struct platform_device_id omap_rtc_devtype[] = { };MODULE_DEVICE_TABLE (platform, omap_rtc_devtype); +static const struct of_device_id omap_rtc_of_match[] = { + { .compatible ="ti,da830-rtc" , + .data = &omap_rtc_devtype[OMAP_RTC_DATA_DA830_IDX ], + }, + {}, +}; +MODULE_DEVICE_TABLE (of, omap_rtc_of_match); +static int __init omap_rtc_probe (struct platform_device *pdev) {struct resource *res, *mem;struct rtc_device *rtc;u8 reg, new_ctrl;const struct platform_device_id *id_entry; +const struct of_device_id *of_id; + + of_id =of_match_device (omap_rtc_of_match, &pdev->dev); +if (of_id) + pdev->id_entry = of_id->data; omap_rtc_timer =platform_get_irq (pdev,0 );if (omap_rtc_timer <=0 ) {
@@ -510,6 +527,7 @@ static struct platform_driver omap_rtc_driver = { .driver = { .name = DRIVER_NAME, .owner = THIS_MODULE, + .of_match_table = of_match_ptr(omap_rtc_of_match), }, .id_table = omap_rtc_devtype, };
Signature · 1 line
1.7.12
Re: [PATCH v4 3/5] rtc: omap: dt support
Quoted 63 lines · Afzal Mohammed
enhance rtc-omap driver with DT capability
Signed-off-by Afzal Mohammed <[email protected]>Acked-by Sekhar Nori <[email protected]>---
v4:
Proper devicetree documentationv2:
Use compatible as ti,da830-rtc instead of ti,am1808-rtcDocumentation/devicetree/bindings/rtc/rtc-omap.txt | 17 +++++++++++++++++ drivers/rtc/rtc-omap.c | 18 ++++++++++++++++++ 2 files changed, 35 insertions(+) create mode 100644 Documentation/devicetree/bindings/rtc/rtc-omap.txtDocumentation/devicetree/bindings/rtc/rtc-omap.txt new file +17
-0@@ -0,0 +1,17 @@ +TI Real Time Clock + +Required properties: +- compatible: "ti,da830-rtc" +- reg: Address range of rtc register set +- interrupts: rtc timer, alarm interrupts in order +- interrupt-parent: phandle for the interrupt controller + +Example: + +rtc at 1c23000 { + compatible = "ti,da830-rtc"; + reg = <0x23000 0x1000>; + interrupts = <19 + 19>; + interrupt-parent = <&intc>; +};drivers/rtc/rtc-omap.c +4
-0@@ -20,6 +20,8 @@#include <linux/rtc.h> #include <linux/bcd.h> #include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_device.h> #include <asm/io.h> @@ -298,6 +300,8 @@ static struct rtc_class_ops omap_rtc_ops = {static int omap_rtc_alarm;static int omap_rtc_timer; +#define OMAP_RTC_DATA_DA830_IDX 1 +static struct platform_device_id omap_rtc_devtype[] = { { .name =DRIVER_NAME ,
drivers/rtc/rtc-omap.c static struct platform_device_id omap_rtc_devtype[] = { · line 318
Quoted 6 lines
drivers/rtc/rtc-omap.c +3
-0@@ -309,12 +313,25 @@ static struct platform_device_id omap_rtc_devtype[] = { };MODULE_DEVICE_TABLE (platform, omap_rtc_devtype); +static const struct of_device_id omap_rtc_of_match[] = { + { .compatible ="ti,da830-rtc" , + .data = &omap_rtc_devtype[OMAP_RTC_DATA_DA830_IDX ],
Wouldn't it make sense to list all the compatible models here? The advantage of a compatible list is that we can name the models explicitly, or maybe at least "davinci-rtc". Is there any reason for this particular name?
Daniel
Quoted 28 lines
drivers/rtc/rtc-omap.c +11
-0+ }, + {}, +}; +MODULE_DEVICE_TABLE (of, omap_rtc_of_match); +static int __init omap_rtc_probe (struct platform_device *pdev) {struct resource *res, *mem;struct rtc_device *rtc;u8 reg, new_ctrl;const struct platform_device_id *id_entry; +const struct of_device_id *of_id; + + of_id =of_match_device (omap_rtc_of_match, &pdev->dev); +if (of_id) + pdev->id_entry = of_id->data; omap_rtc_timer =platform_get_irq (pdev,0 );if (omap_rtc_timer <=0 ) {@@ -510,6 +527,7 @@ static struct platform_driver omap_rtc_driver = { .driver = { .name = DRIVER_NAME, .owner = THIS_MODULE, + .of_match_table = of_match_ptr(omap_rtc_of_match), }, .id_table = omap_rtc_devtype, };
Re: [PATCH v4 3/5] rtc: omap: dt support
Hi Daniel,
Quoted 10 lines · Daniel Mack
drivers/rtc/rtc-omap.c static struct platform_device_id omap_rtc_devtype[] = {
Quoted 3 lines · Afzal Mohammed
drivers/rtc/rtc-omap.c +3
-0+static const struct of_device_id omap_rtc_of_match[] = { + { .compatible ="ti,da830-rtc" , + .data =&omap_rtc_devtype[OMAP_RTC_DATA_DA830_IDX ],Wouldn't it make sense to list all the compatible models here? The advantage of a compatible list is that we can name the models explicitly, or maybe at least "davinci-rtc". Is there any reason for this particular name?
Exact name followed by compatible models needs to be specified in DT node only, right ? (when driver for the first variant can handle it)
And when additional features of newer IP's has to be leveraged, new entries can be added in the driver match table.
First known variant of SoC for DT is da830 (exact name), hence it was used.
Regards
Afzal
PATCH v4 4/5 rtc: omap: depend on am33xx
In reply to Afzal Mohammedrtc-omap driver can be reused for AM33xx RTC.
Provide dependency in Kconfig.
---
v2:
Modify Kconfig help, resolve checkpatch warning
drivers/rtc/Kconfig | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-)
drivers/rtc/Kconfig +6 -4
@@ -777,11 +777,13 @@ config RTC_DRV_IMXDI config RTC_DRV_OMAP tristate "TI OMAP1" - depends on ARCH_OMAP15XX || ARCH_OMAP16XX || ARCH_OMAP730 || ARCH_DAVINCI_DA8XX + depends on ARCH_OMAP15XX || ARCH_OMAP16XX || ARCH_OMAP730 || ARCH_DAVINCI_DA8XX || SOC_AM33XX help - Say "yes" here to support the real time clock on TI OMAP1 and - DA8xx/OMAP-L13x chips. This driver can also be built as a - module called rtc-omap. + Say "yes" here to support the on chip real time clock + present on TI OMAP1, AM33xx and DA8xx/OMAP-L13x. + + This driver can also be built as a module, if so, module + will be called rtc-omap. config HAVE_S3C_RTC bool
Signature · 1 line
1.7.12
PATCH v4 5/5 rtc: omap: Add runtime pm support
In reply to Afzal MohammedFrom: Vaibhav Hiremath <[email protected]>
OMAP1 RTC driver is used in multiple devices like,
OMAPL138 and AM33XX. Driver currently doesn't handle any clocks, which may be right for OMAP1 architecture but in case of AM33XX, the clock/module needs to be enabled in order to access the registers.
So covert this driver to runtime pm, which internally handles rest.
afzal at ti.com: handle error path
--- drivers/rtc/rtc-omap.c | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)
drivers/rtc/rtc-omap.c +18 -0
@@ -22,6 +22,7 @@#include <linux/platform_device.h> #include <linux/of.h> #include <linux/of_device.h> +#include <linux/pm_runtime.h> #include <asm/io.h>
@@ -364,6 +365,10 @@ static int __init omap_rtc_probe(struct platform_device *pdev) goto fail; } +/* Enable the clock/module so that we can access the registers */ +pm_runtime_enable (&pdev->dev); +pm_runtime_get_sync (&pdev->dev); + id_entry =platform_get_device_id (pdev);if (id_entry && (id_entry->driver_data &OMAP_RTC_HAS_KICKER )) {rtc_writel (KICK0_VALUE ,OMAP_RTC_KICK0_REG );
@@ -448,6 +453,8 @@ fail1: fail0:if (id_entry && (id_entry->driver_data &OMAP_RTC_HAS_KICKER ))rtc_writel (0 ,OMAP_RTC_KICK0_REG ); +pm_runtime_put_sync (&pdev->dev); +pm_runtime_disable (&pdev->dev);iounmap (rtc_base); fail:release_mem_region (mem->start,resource_size (mem));
@@ -474,6 +481,11 @@ static int __exit omap_rtc_remove(struct platform_device *pdev)rtc_device_unregister (rtc);if (id_entry && (id_entry->driver_data &OMAP_RTC_HAS_KICKER ))rtc_writel (0 ,OMAP_RTC_KICK0_REG ); + +/* Disable the clock/module */ +pm_runtime_put_sync (&pdev->dev); +pm_runtime_disable (&pdev->dev); +iounmap (rtc_base);release_mem_region (mem->start,resource_size (mem));return 0 ;
@@ -496,11 +508,17 @@ static int omap_rtc_suspend(struct platform_device *pdev, pm_message_t state)else rtc_write (0 ,OMAP_RTC_INTERRUPTS_REG ); +/* Disable the clock/module */ +pm_runtime_put_sync (&pdev->dev); +return 0 ; }static int omap_rtc_resume (struct platform_device *pdev) { +/* Enable the clock/module so that we can access the registers */ +pm_runtime_get_sync (&pdev->dev); +if (device_may_wakeup (&pdev->dev))disable_irq_wake (omap_rtc_alarm);else
Signature · 1 line
1.7.12