r8169: fix rtl8168h wol fail
PATCH 1/1 r8169: fix rtl8168h wol fail
rtl8168h has an application that it will connect to rtl8211fs through mdi interface. And rtl8211fs will connect to fiber through serdes interface. In this application, rtl8168h revision id will be set to 0x2a.
Because rtl8211fs's firmware will set link capability to 100M and GIGA when link is from off to on. So when system suspend and wol is enabled, rtl8168h will speed down to 100M (because rtl8211fs advertise 100M and GIGA to rtl8168h). If the link speed between rtl81211fs and fiber is GIGA. The link speed between rtl8168h and fiber will mismatch. That will cause wol fail.
In this patch, if rtl8168h is in this kind of application, driver will not speed down phy when wol is enabled.
--- drivers/net/ethernet/realtek/r8169_main.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)
drivers/net/ethernet/realtek/r8169_main.c +8 -1
@@ -1199,6 +1199,12 @@ static enum rtl_dash_type rtl_check_dash(struct rtl8169_private *tp) } } +static bool rtl_mdi_connect_to_phy (struct rtl8169_private *tp) +{ +return tp->mac_version ==RTL_GIGA_MAC_VER_46 && + tp->pci_dev->revision ==0x2a ; +} +static void rtl_set_d3_pll_down (struct rtl8169_private *tp,bool enable) {switch (tp->mac_version) {
@@ -2453,7 +2459,8 @@ static void rtl_prepare_power_down(struct rtl8169_private *tp)rtl_ephy_write (tp,0x19 ,0xff64 );if (device_may_wakeup (tp_to_dev (tp))) { -phy_speed_down (tp->phydev, false); +if (!rtl_mdi_connect_to_phy (tp)) +phy_speed_down (tp->phydev, false);rtl_wol_enable_rx (tp); } }
Signature · 1 line
2.39.0
Heiner Kallweit
maintainerQuoted 11 lines · Chunhao Lin
rtl8168h has an application that it will connect to rtl8211fs through mdi interface. And rtl8211fs will connect to fiber through serdes interface. In this application, rtl8168h revision id will be set to
0x2a.Because rtl8211fs's firmware will set link capability to 100M and GIGA when link is from off to on. So when system suspend and wol is enabled, rtl8168h will speed down to 100M (because rtl8211fs advertise 100M and GIGA to rtl8168h). If the link speed between rtl81211fs and fiber is GIGA. The link speed between rtl8168h and fiber will mismatch. That will cause wol fail.
Quoted 3 lines
In this patch, if rtl8168h is in this kind of application, driver will not speed down phy when wol is enabled.
I think the patch title is inappropriate because WoL works normally on RTL8168h in the standard setup.
What you add isn't a fix but a workaround for a firmware bug in RTL8211FS. As mentioned in a previous review comment: if speed on fibre side is 1Gbps then RTL8211FS shouldn't advertise 100Mbps on MDI/UTP side.
Last but not least the user can still use e.g. ethtool to change the speed to 100Mbps thus breaking the link.
Quoted 10 lines
Signed-off-by Chunhao Lin <[email protected]>--- drivers/net/ethernet/realtek/r8169_main.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)drivers/net/ethernet/realtek/r8169_main.c +0
-0
drivers/net/ethernet/realtek/r8169_main.c static enum rtl_dash_type rtl_check_dash(struct rtl8169_private *tp) · line 1202
Quoted 4 lines
drivers/net/ethernet/realtek/r8169_main.c +1
-0@@ -1199,6 +1199,12 @@ static enum rtl_dash_type rtl_check_dash(struct rtl8169_private *tp) } } +static bool rtl_mdi_connect_to_phy (struct rtl8169_private *tp)
A comment would be helpful so that a reader of the code knows what it's good for. A brief description of the non-standard setup with the internal PHY connected to another PHY in media converter mode would be good.
Quoted 18 lines
drivers/net/ethernet/realtek/r8169_main.c +7
-1+{ +return tp->mac_version ==RTL_GIGA_MAC_VER_46 && + tp->pci_dev->revision ==0x2a ; +} +static void rtl_set_d3_pll_down (struct rtl8169_private *tp,bool enable) {switch (tp->mac_version) {@@ -2453,7 +2459,8 @@ static void rtl_prepare_power_down(struct rtl8169_private *tp)rtl_ephy_write (tp,0x19 ,0xff64 );if (device_may_wakeup (tp_to_dev (tp))) { -phy_speed_down (tp->phydev, false); +if (!rtl_mdi_connect_to_phy (tp)) +phy_speed_down (tp->phydev, false);rtl_wol_enable_rx (tp); } }
Quoted 15 lines · Heiner Kallweit
Quoted 11 lines · Chunhao Lin
rtl8168h has an application that it will connect to rtl8211fs through mdi interface. And rtl8211fs will connect to fiber through serdes interface. In this application, rtl8168h revision id will be set to
0x2a.Because rtl8211fs's firmware will set link capability to 100M and GIGA when link is from off to on. So when system suspend and wol is enabled, rtl8168h will speed down to 100M (because rtl8211fs advertise 100M and GIGA to rtl8168h). If the link speed between rtl81211fs and fiber is GIGA. The link speed between rtl8168h and fiber will mismatch. That will cause wol fail.
Quoted 3 lines
In this patch, if rtl8168h is in this kind of application, driver will not speed down phy when wol is enabled.
Quoted 8 lines
I think the patch title is inappropriate because WoL works normally on RTL8168h in the standard setup.
What you add isn't a fix but a workaround for a firmware bug in RTL8211FS. As mentioned in a previous review comment: if speed on fibre side is 1Gbps then RTL8211FS shouldn't advertise 100Mbps on MDI/UTP side.Last but not least the user can still use e.g. ethtool to change the speed to 100Mbps thus breaking the link.
I agree with Heiner here. I assume you cannot fix the firmware?
So can we detect the broken firmware and correctly set phydev->advertising? That will fix WoL and should prevent the user from using ethtool to select a slower speed.
Andrew
Quoted 24 lines
Quoted 2 lines
Quoted 2 lines
rtl8168h has an application that it will connect to rtl8211fs through mdi interface. And rtl8211fs will connect to fiber through serdes
interface.
Quoted 6 lines
Quoted 6 lines
In this application, rtl8168h revision id will be set to
0x2a.Because rtl8211fs's firmware will set link capability to 100M and GIGA when link is from off to on. So when system suspend and wol is enabled, rtl8168h will speed down to 100M (because rtl8211fs advertise 100M and GIGA to rtl8168h). If the link speed between
rtl81211fs and fiber is GIGA.
Quoted 6 lines
Quoted 6 lines
The link speed between rtl8168h and fiber will mismatch. That will cause wol fail.
In this patch, if rtl8168h is in this kind of application, driver will not speed down phy when wol is enabled.
Quoted 7 lines
I think the patch title is inappropriate because WoL works normally on RTL8168h in the standard setup.
What you add isn't a fix but a workaround for a firmware bug in RTL8211FS. As mentioned in a previous review comment: if speed on fibre side is 1Gbps then RTL8211FS shouldn't advertise 100Mbps on MDI/UTP side. Last but not least the user can still use e.g. ethtool to change the speed to 100Mbps thus breaking the link.
Quoted 6 lines
I agree with Heiner here. I assume you cannot fix the firmware?
So can we detect the broken firmware and correctly set
phydev->advertising? That will fix WoL and should prevent the user from using ethtool to select a slower speed.
It is a rtl8211fs's firmware bug. Because in this application it will support both 100M and GIGA fiber module, so it cannot just set phydev->advertising to 100M or GIGA. We may need to use bit-bang MDIO to detect fiber link speed and set phydev->advertising properly. But it will let this patch become more complicated.
------Please consider the environment before printing this e-mail.
Quoted 26 lines · Hau
Quoted 26 lines
Quoted 2 lines
Quoted 2 lines
rtl8168h has an application that it will connect to rtl8211fs through mdi interface. And rtl8211fs will connect to fiber through serdes
interface.
Quoted 6 lines
Quoted 6 lines
In this application, rtl8168h revision id will be set to
0x2a.Because rtl8211fs's firmware will set link capability to 100M and GIGA when link is from off to on. So when system suspend and wol is enabled, rtl8168h will speed down to 100M (because rtl8211fs advertise 100M and GIGA to rtl8168h). If the link speed between
rtl81211fs and fiber is GIGA.
Quoted 6 lines
Quoted 6 lines
The link speed between rtl8168h and fiber will mismatch. That will cause wol fail.
In this patch, if rtl8168h is in this kind of application, driver will not speed down phy when wol is enabled.
Quoted 7 lines
I think the patch title is inappropriate because WoL works normally on RTL8168h in the standard setup.
What you add isn't a fix but a workaround for a firmware bug in RTL8211FS. As mentioned in a previous review comment: if speed on fibre side is 1Gbps then RTL8211FS shouldn't advertise 100Mbps on MDI/UTP side. Last but not least the user can still use e.g. ethtool to change the speed to 100Mbps thus breaking the link.I agree with Heiner here. I assume you cannot fix the firmware?
Quoted 8 lines
Quoted 4 lines
So can we detect the broken firmware and correctly set
phydev->advertising? That will fix WoL and should prevent the user from using ethtool to select a slower speed.It is a rtl8211fs's firmware bug. Because in this application it will support both 100M and GIGA fiber module, so it cannot just set
phydev->advertisingto 100M or GIGA. We may need to use bit-bang MDIO to detect fiber link speed and setphydev->advertisingproperly. But it will let this patch become more complicated.
You mean you will read the EEPROM in the SFP to determine what it supports? If so, please use phylink, and the SFP driver, which will do this for you.
Andrew
Heiner Kallweit
maintainerQuoted 26 lines · Hau
Quoted 26 lines
Quoted 2 lines
Quoted 2 lines
rtl8168h has an application that it will connect to rtl8211fs through mdi interface. And rtl8211fs will connect to fiber through serdes
interface.
Quoted 6 lines
Quoted 6 lines
In this application, rtl8168h revision id will be set to
0x2a.Because rtl8211fs's firmware will set link capability to 100M and GIGA when link is from off to on. So when system suspend and wol is enabled, rtl8168h will speed down to 100M (because rtl8211fs advertise 100M and GIGA to rtl8168h). If the link speed between
rtl81211fs and fiber is GIGA.
Quoted 6 lines
Quoted 6 lines
The link speed between rtl8168h and fiber will mismatch. That will cause wol fail.
In this patch, if rtl8168h is in this kind of application, driver will not speed down phy when wol is enabled.
Quoted 7 lines
I think the patch title is inappropriate because WoL works normally on RTL8168h in the standard setup.
What you add isn't a fix but a workaround for a firmware bug in RTL8211FS. As mentioned in a previous review comment: if speed on fibre side is 1Gbps then RTL8211FS shouldn't advertise 100Mbps on MDI/UTP side. Last but not least the user can still use e.g. ethtool to change the speed to 100Mbps thus breaking the link.I agree with Heiner here. I assume you cannot fix the firmware?
Quoted 9 lines
Quoted 4 lines
So can we detect the broken firmware and correctly set
phydev->advertising? That will fix WoL and should prevent the user from using ethtool to select a slower speed.It is a rtl8211fs's firmware bug. Because in this application it will support both 100M and GIGA fiber module, so it cannot just set
phydev->advertisingto 100M or GIGA. We may need to use bit-bang MDIO to detect fiber link speed and setphydev->advertisingproperly. But it will let this patch become more complicated.
I think there's also a userspace workaround for your problem.
You can use "ethtool -s <if> advertise .." to adjust what the internal PHY advertises. phy_speed_down() considers only modes that are currently advertised.
In your case with a 1Gbps fibre module you could set the advertisement to 1Gbps/full only. Then phy_speed_down() wouldn't change the speed.
Quoted 40 lines · Hau
Quoted 14 lines
Quoted 14 lines
Quoted 3 lines
Quoted 3 lines
rtl8168h has an application that it will connect to rtl8211fs through mdi interface. And rtl8211fs will connect to fiber through serdes
interface.
Quoted 6 lines
Quoted 6 lines
In this application, rtl8168h revision id will be set to
0x2a.Because rtl8211fs's firmware will set link capability to 100M and GIGA when link is from off to on. So when system suspend and wol is enabled, rtl8168h will speed down to 100M (because rtl8211fs advertise 100M and GIGA to rtl8168h). If the link speed between
rtl81211fs and fiber is GIGA.
Quoted 3 lines
Quoted 3 lines
The link speed between rtl8168h and fiber will mismatch. That will cause wol fail.
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 3 lines
In this patch, if rtl8168h is in this kind of application, driver will not speed down phy when wol is enabled.
I think the patch title is inappropriate because WoL works normally on RTL8168h in the standard setup.
What you add isn't a fix but a workaround for a firmware bug inRTL8211FS.
Quoted 7 lines
Quoted 7 lines
Quoted 4 lines
As mentioned in a previous review comment: if speed on fibre side is 1Gbps then RTL8211FS shouldn't advertise 100Mbps on MDI/UTP side. Last but not least the user can still use e.g. ethtool to change the speed to 100Mbps thus breaking the link.
I agree with Heiner here. I assume you cannot fix the firmware?
Quoted 7 lines
Quoted 4 lines
So can we detect the broken firmware and correctly set
phydev->advertising? That will fix WoL and should prevent the user from using ethtool to select a slower speed.It is a rtl8211fs's firmware bug. Because in this application it will support both 100M and GIGA fiber module, so it cannot just set
phydev->advertisingto 100M or GIGA. We may need to use bit-bangMDIO
Quoted 1 line
to detect fiber link speed and set
phydev->advertisingproperly. But it willlet this patch become more complicated.
Quoted 1 line
Quoted 9 lines
I think there's also a userspace workaround for your problem. You can use "ethtool -s <if> advertise .." to adjust what the internal PHY advertises.
phy_speed_down()considers only modes that are currently advertised.In your case with a 1Gbps fibre module you could set the advertisement to 1Gbps/full only.
Thenphy_speed_down()wouldn't change the speed.
In this application(rtl8168h + rtl8211fs) it also supports 100Mbps fiber module. So userspace workaround is good but it may not always work for this issue. Not speed down during system suspend may be the simplest workaround for this issue.
------Please consider the environment before printing this e-mail.
Heiner Kallweit
maintainerQuoted 45 lines · Hau
Quoted 45 lines · Hau
Quoted 14 lines
Quoted 14 lines
Quoted 3 lines
Quoted 3 lines
rtl8168h has an application that it will connect to rtl8211fs through mdi interface. And rtl8211fs will connect to fiber through serdes
interface.
Quoted 6 lines
Quoted 6 lines
In this application, rtl8168h revision id will be set to
0x2a.Because rtl8211fs's firmware will set link capability to 100M and GIGA when link is from off to on. So when system suspend and wol is enabled, rtl8168h will speed down to 100M (because rtl8211fs advertise 100M and GIGA to rtl8168h). If the link speed between
rtl81211fs and fiber is GIGA.
Quoted 3 lines
Quoted 3 lines
The link speed between rtl8168h and fiber will mismatch. That will cause wol fail.
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 3 lines
In this patch, if rtl8168h is in this kind of application, driver will not speed down phy when wol is enabled.
I think the patch title is inappropriate because WoL works normally on RTL8168h in the standard setup.
What you add isn't a fix but a workaround for a firmware bug inRTL8211FS.
Quoted 7 lines
Quoted 7 lines
Quoted 4 lines
As mentioned in a previous review comment: if speed on fibre side is 1Gbps then RTL8211FS shouldn't advertise 100Mbps on MDI/UTP side. Last but not least the user can still use e.g. ethtool to change the speed to 100Mbps thus breaking the link.
I agree with Heiner here. I assume you cannot fix the firmware?
Quoted 7 lines
Quoted 4 lines
So can we detect the broken firmware and correctly set
phydev->advertising? That will fix WoL and should prevent the user from using ethtool to select a slower speed.It is a rtl8211fs's firmware bug. Because in this application it will support both 100M and GIGA fiber module, so it cannot just set
phydev->advertisingto 100M or GIGA. We may need to use bit-bangMDIO
Quoted 1 line
to detect fiber link speed and set
phydev->advertisingproperly. But it willlet this patch become more complicated.
Quoted 1 line
I think there's also a userspace workaround for your problem. You can use "ethtool -s <if> advertise .." to adjust what the internal PHY advertises.
phy_speed_down()considers only modes that are currently advertised.
Quoted 5 lines
Quoted 4 lines
In your case with a 1Gbps fibre module you could set the advertisement to 1Gbps/full only.
Thenphy_speed_down()wouldn't change the speed.In this application(rtl8168h + rtl8211fs) it also supports 100Mbps fiber module.
Does RTL8211FS advertise 100Mbps and 1Gbps on the UTP/MDI side in case of a 100Mbps fiber module?
Quoted 1 line
So userspace workaround is good but it may not always work for this issue.
When would it not work? If you know the fiber module speed you can set the advertisement accordingly.
Quoted 2 lines
Not speed down during system suspend may be the simplest workaround for this issue.
Quoted 53 lines · Hau
Quoted 18 lines
Quoted 18 lines · Hau
Quoted 17 lines
Quoted 17 lines
Quoted 3 lines
Quoted 3 lines
rtl8168h has an application that it will connect to rtl8211fs through mdi interface. And rtl8211fs will connect to fiber through serdes
interface.
Quoted 6 lines
Quoted 6 lines
In this application, rtl8168h revision id will be set to
0x2a.Because rtl8211fs's firmware will set link capability to 100M and GIGA when link is from off to on. So when system suspend and wol is enabled, rtl8168h will speed down to 100M (because rtl8211fs advertise 100M and GIGA to rtl8168h). If the link speed between
rtl81211fs and fiber is GIGA.
Quoted 6 lines
Quoted 6 lines
The link speed between rtl8168h and fiber will mismatch. That will cause wol fail.
In this patch, if rtl8168h is in this kind of application, driver will not speed down phy when wol is enabled.
Quoted 6 lines
Quoted 6 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
I think the patch title is inappropriate because WoL works normally on RTL8168h in the standard setup.
What you add isn't a fix but a workaround for a firmware bug inRTL8211FS.
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
As mentioned in a previous review comment: if speed on fibre side is 1Gbps then RTL8211FS shouldn't advertise 100Mbps on MDI/UTP
side.
Quoted 26 lines
Quoted 26 lines
Quoted 5 lines
Quoted 5 lines
Quoted 2 lines
Last but not least the user can still use e.g. ethtool to change the speed to 100Mbps thus breaking the link.
I agree with Heiner here. I assume you cannot fix the firmware?
Quoted 7 lines
Quoted 4 lines
So can we detect the broken firmware and correctly set
phydev->advertising? That will fix WoL and should prevent the user from using ethtool to select a slower speed.It is a rtl8211fs's firmware bug. Because in this application it will support both 100M and GIGA fiber module, so it cannot just set
phydev->advertisingto 100M or GIGA. We may need to use bit-bangMDIO
Quoted 2 lines
to detect fiber link speed and set
phydev->advertisingproperly. But it willlet this patch become more complicated.
Quoted 1 line
I think there's also a userspace workaround for your problem. You can use "ethtool -s <if> advertise .." to adjust what the internal PHY advertises.
phy_speed_down()considers only modes that are currently advertised.In your case with a 1Gbps fibre module you could set the advertisement to 1Gbps/full only.
Thenphy_speed_down()wouldn't change the speed.
Quoted 5 lines
Quoted 1 line
In this application(rtl8168h + rtl8211fs) it also supports 100Mbps fiber
module.
Does RTL8211FS advertise 100Mbps and 1Gbps on the UTP/MDI side in case of a 100Mbps fiber module?
Yes.
Quoted 4 lines
Quoted 1 line
So userspace workaround is good but it may not always work for this issue.
When would it not work? If you know the fiber module speed you can set the advertisement accordingly.
Sure, user can set internal PHY advertisement according to fiber module speed. But we would like to have a solution that does not need user to do anything. So this userspace workaround may not meet our need.
Quoted 3 lines
Quoted 1 line
Not speed down during system suspend may be the simplest workaround
for this issue.
Quoted 1 line
------Please consider the environment before printing this e-mail.
Heiner Kallweit
maintainerQuoted 53 lines · Hau
Quoted 53 lines · Hau
Quoted 18 lines
Quoted 18 lines · Hau
Quoted 17 lines
Quoted 17 lines
Quoted 3 lines
Quoted 3 lines
rtl8168h has an application that it will connect to rtl8211fs through mdi interface. And rtl8211fs will connect to fiber through serdes
interface.
Quoted 6 lines
Quoted 6 lines
In this application, rtl8168h revision id will be set to
0x2a.Because rtl8211fs's firmware will set link capability to 100M and GIGA when link is from off to on. So when system suspend and wol is enabled, rtl8168h will speed down to 100M (because rtl8211fs advertise 100M and GIGA to rtl8168h). If the link speed between
rtl81211fs and fiber is GIGA.
Quoted 6 lines
Quoted 6 lines
The link speed between rtl8168h and fiber will mismatch. That will cause wol fail.
In this patch, if rtl8168h is in this kind of application, driver will not speed down phy when wol is enabled.
Quoted 6 lines
Quoted 6 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
I think the patch title is inappropriate because WoL works normally on RTL8168h in the standard setup.
What you add isn't a fix but a workaround for a firmware bug inRTL8211FS.
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
As mentioned in a previous review comment: if speed on fibre side is 1Gbps then RTL8211FS shouldn't advertise 100Mbps on MDI/UTP
side.
Quoted 26 lines
Quoted 26 lines
Quoted 5 lines
Quoted 5 lines
Quoted 2 lines
Last but not least the user can still use e.g. ethtool to change the speed to 100Mbps thus breaking the link.
I agree with Heiner here. I assume you cannot fix the firmware?
Quoted 7 lines
Quoted 4 lines
So can we detect the broken firmware and correctly set
phydev->advertising? That will fix WoL and should prevent the user from using ethtool to select a slower speed.It is a rtl8211fs's firmware bug. Because in this application it will support both 100M and GIGA fiber module, so it cannot just set
phydev->advertisingto 100M or GIGA. We may need to use bit-bangMDIO
Quoted 2 lines
to detect fiber link speed and set
phydev->advertisingproperly. But it willlet this patch become more complicated.
Quoted 1 line
I think there's also a userspace workaround for your problem. You can use "ethtool -s <if> advertise .." to adjust what the internal PHY advertises.
phy_speed_down()considers only modes that are currently advertised.In your case with a 1Gbps fibre module you could set the advertisement to 1Gbps/full only.
Thenphy_speed_down()wouldn't change the speed.
Quoted 7 lines
Quoted 5 lines
Quoted 1 line
In this application(rtl8168h + rtl8211fs) it also supports 100Mbps fiber
module.
Does RTL8211FS advertise 100Mbps and 1Gbps on the UTP/MDI side in case of a 100Mbps fiber module?
Yes.
I think in this case internal PHY and RTL8211FS would negotiate 1Gbps, not matching the speed of the 100Mbps fiber module.
How does this work?
Quoted 11 lines
Quoted 4 lines
Quoted 1 line
So userspace workaround is good but it may not always work for this issue.
When would it not work? If you know the fiber module speed you can set the advertisement accordingly.
Sure, user can set internal PHY advertisement according to fiber module speed. But we would like to have a solution that does not need user to do anything. So this userspace workaround may not meet our need.
Quoted 3 lines
Quoted 1 line
Not speed down during system suspend may be the simplest workaround
for this issue.
Quoted 1 line
Quoted 10 lines
Quoted 7 lines
Quoted 5 lines
Quoted 1 line
In this application(rtl8168h + rtl8211fs) it also supports 100Mbps fiber
module.
Does RTL8211FS advertise 100Mbps and 1Gbps on the UTP/MDI side in case of a 100Mbps fiber module?
Yes.
I think in this case internal PHY and RTL8211FS would negotiate 1Gbps, not matching the speed of the 100Mbps fiber module.
How does this work?
Fibre line side has no autoneg. Both ends need to be using the same speed, or the SERDES does not synchronise and does not establish link.
You can ask the SFP module what baud rate it supports, and then use anything up to that baud rate. I've got systems where the SFP is fast enough to support a 2.5Gbps link, so the MAC indicates both 2.5G and 1G, defaults to 2.5G, and fails to connect to a 1G link peer. You need to use ethtool to force it to the lower speed before the link works.
But from what i understand, you cannot use a 1000Base-X SFP, set the MAC to 100Mbps, and expect it to connect to a 100Base-FX SFP. So for me, the RTL8211FS should not be advertise 100Mbps and 1Gbps, it needs to talk to the SFP figure out exactly what it is, and only advertise the one mode which is supported.
Andrew
Quoted 11 lines
Quoted 11 lines
Quoted 8 lines
Quoted 6 lines
Quoted 2 lines
In this application(rtl8168h + rtl8211fs) it also supports 100Mbps fiber
module.
Does RTL8211FS advertise 100Mbps and 1Gbps on the UTP/MDI side in case of a 100Mbps fiber module?
Yes.
I think in this case internal PHY and RTL8211FS would negotiate 1Gbps, not matching the speed of the 100Mbps fiber module.
How does this work?
My mistake. With 100Mbps fiber module RTL8211FS will only advertise 100Mbps on the UTP/MDI side. With 1Gbps fiber module it will advertise both 100Mbps and 1Gbps. So issue will only happen with 1Gbps fiber module.
Quoted 9 lines
Fibre line side has no autoneg. Both ends need to be using the same speed, or the SERDES does not synchronise and does not establish link.
You can ask the SFP module what baud rate it supports, and then use anything up to that baud rate. I've got systems where the SFP is fast enough to support a 2.5Gbps link, so the MAC indicates both 2.5G and 1G, defaults to 2.5G, and fails to connect to a 1G link peer. You need to use ethtool to force it to the lower speed before the link works.
Quoted 5 lines
But from what i understand, you cannot use a 1000Base-X SFP, set the MAC to 100Mbps, and expect it to connect to a 100Base-FX SFP. So for me, the RTL8211FS should not be advertise 100Mbps and 1Gbps, it needs to talk to the SFP figure out exactly what it is, and only advertise the one mode which is supported.
It is the RTL8211FS firmware bug. This patch is for workaround this issue.
------Please consider the environment before printing this e-mail.
Quoted 25 lines · Hau
Quoted 11 lines
Quoted 11 lines
Quoted 8 lines
Quoted 6 lines
Quoted 2 lines
In this application(rtl8168h + rtl8211fs) it also supports 100Mbps fiber
module.
Does RTL8211FS advertise 100Mbps and 1Gbps on the UTP/MDI side in case of a 100Mbps fiber module?
Yes.
I think in this case internal PHY and RTL8211FS would negotiate 1Gbps, not matching the speed of the 100Mbps fiber module.
How does this work?My mistake. With 100Mbps fiber module RTL8211FS will only advertise 100Mbps on the UTP/MDI side. With 1Gbps fiber module it will advertise both 100Mbps and 1Gbps. So issue will only happen with 1Gbps fiber module.
Quoted 9 lines
Fibre line side has no autoneg. Both ends need to be using the same speed, or the SERDES does not synchronise and does not establish link.
You can ask the SFP module what baud rate it supports, and then use anything up to that baud rate. I've got systems where the SFP is fast enough to support a 2.5Gbps link, so the MAC indicates both 2.5G and 1G, defaults to 2.5G, and fails to connect to a 1G link peer. You need to use ethtool to force it to the lower speed before the link works.
Quoted 7 lines
Quoted 5 lines
But from what i understand, you cannot use a 1000Base-X SFP, set the MAC to 100Mbps, and expect it to connect to a 100Base-FX SFP. So for me, the RTL8211FS should not be advertise 100Mbps and 1Gbps, it needs to talk to the SFP figure out exactly what it is, and only advertise the one mode which is supported.
It is the RTL8211FS firmware bug. This patch is for workaround this issue.
So if it is advertising both 100Mbps and 1Gbps, we know the SFP is actually 1G, and we can remove the 100Mbps advertisement? That should then solve all the problems?
Andrew
Heiner Kallweit
maintainerQuoted 32 lines · Andrew Lunn
Quoted 31 lines · Hau
Quoted 11 lines
Quoted 11 lines
Quoted 8 lines
Quoted 6 lines
Quoted 2 lines
In this application(rtl8168h + rtl8211fs) it also supports 100Mbps fiber
module.
Does RTL8211FS advertise 100Mbps and 1Gbps on the UTP/MDI side in case of a 100Mbps fiber module?
Yes.
I think in this case internal PHY and RTL8211FS would negotiate 1Gbps, not matching the speed of the 100Mbps fiber module.
How does this work?My mistake. With 100Mbps fiber module RTL8211FS will only advertise 100Mbps on the UTP/MDI side. With 1Gbps fiber module it will advertise both 100Mbps and 1Gbps. So issue will only happen with 1Gbps fiber module.
Quoted 14 lines
Fibre line side has no autoneg. Both ends need to be using the same speed, or the SERDES does not synchronise and does not establish link.
You can ask the SFP module what baud rate it supports, and then use anything up to that baud rate. I've got systems where the SFP is fast enough to support a 2.5Gbps link, so the MAC indicates both 2.5G and 1G, defaults to 2.5G, and fails to connect to a 1G link peer. You need to use ethtool to force it to the lower speed before the link works.
But from what i understand, you cannot use a 1000Base-X SFP, set the MAC to 100Mbps, and expect it to connect to a 100Base-FX SFP. So for me, the RTL8211FS should not be advertise 100Mbps and 1Gbps, it needs to talk to the SFP figure out exactly what it is, and only advertise the one mode which is supported.
Quoted 6 lines
Quoted 1 line
It is the RTL8211FS firmware bug. This patch is for workaround this issue.
So if it is advertising both 100Mbps and 1Gbps, we know the SFP is actually 1G, and we can remove the 100Mbps advertisement? That should then solve all the problems?
Right, that's what I proposed too, removing 1Gbps advertisement of the RTL8168H-internal PHY via userspace tool, e.g. ethtool. For me this is the cleanest solution. Adding a workaround for a firmware bug of a specific external PHY to the r8169 MAC driver would be somewhat hacky.
Quoted 1 line
Andrew
Quoted 38 lines · Andrew Lunn
Quoted 6 lines · Hau
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 2 lines
In this application(rtl8168h + rtl8211fs) it also supports 100Mbps fiber
module.
Does RTL8211FS advertise 100Mbps and 1Gbps on the UTP/MDI side
in
Quoted 10 lines
Quoted 10 lines
Quoted 6 lines
Quoted 6 lines
Quoted 3 lines
Quoted 1 line
case of a 100Mbps fiber module?
Yes.
I think in this case internal PHY and RTL8211FS would negotiate 1Gbps, not matching the speed of the 100Mbps fiber module. How does this work?
My mistake. With 100Mbps fiber module RTL8211FS will only advertise 100Mbps on the UTP/MDI side. With 1Gbps fiber module it will advertise both 100Mbps and 1Gbps. So issue will only happen with 1Gbps
fiber module.
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
Fibre line side has no autoneg. Both ends need to be using the same speed, or the SERDES does not synchronise and does not establish link.
You can ask the SFP module what baud rate it supports, and then use anything up to that baud rate. I've got systems where the SFP is fast enough to support a 2.5Gbps link, so the MAC indicates both 2.5G and 1G, defaults to 2.5G, and fails to connect to a 1G link peer. You need to use ethtool to force it to the lower speed before the
link works.
Quoted 9 lines
Quoted 8 lines
Quoted 6 lines
But from what i understand, you cannot use a 1000Base-X SFP, set the MAC to 100Mbps, and expect it to connect to a 100Base-FX SFP. So for me, the RTL8211FS should not be advertise 100Mbps and 1Gbps, it needs to talk to the SFP figure out exactly what it is, and only advertise the one mode which is supported.
It is the RTL8211FS firmware bug. This patch is for workaround this issue.
Quoted 9 lines
Quoted 4 lines
So if it is advertising both 100Mbps and 1Gbps, we know the SFP is actually 1G, and we can remove the 100Mbps advertisement? That should then solve all the problems?
Right, that's what I proposed too, removing 1Gbps advertisement of the RTL8168H-internal PHY via userspace tool, e.g. ethtool. For me this is the cleanest solution. Adding a workaround for a firmware bug of a specific external PHY to the r8169 MAC driver would be somewhat hacky.
Thanks for your suggestions. But because it needs user to execute userspace tool. This workaround may not be accepted by our customer
------Please consider the environment before printing this e-mail.
Heiner Kallweit
maintainerQuoted 42 lines · Hau
Quoted 42 lines · Andrew Lunn
Quoted 6 lines · Hau
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 2 lines
In this application(rtl8168h + rtl8211fs) it also supports 100Mbps fiber
module.
Does RTL8211FS advertise 100Mbps and 1Gbps on the UTP/MDI side
in
Quoted 10 lines
Quoted 10 lines
Quoted 6 lines
Quoted 6 lines
Quoted 3 lines
Quoted 1 line
case of a 100Mbps fiber module?
Yes.
I think in this case internal PHY and RTL8211FS would negotiate 1Gbps, not matching the speed of the 100Mbps fiber module. How does this work?
My mistake. With 100Mbps fiber module RTL8211FS will only advertise 100Mbps on the UTP/MDI side. With 1Gbps fiber module it will advertise both 100Mbps and 1Gbps. So issue will only happen with 1Gbps
fiber module.
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
Fibre line side has no autoneg. Both ends need to be using the same speed, or the SERDES does not synchronise and does not establish link.
You can ask the SFP module what baud rate it supports, and then use anything up to that baud rate. I've got systems where the SFP is fast enough to support a 2.5Gbps link, so the MAC indicates both 2.5G and 1G, defaults to 2.5G, and fails to connect to a 1G link peer. You need to use ethtool to force it to the lower speed before the
link works.
Quoted 13 lines
Quoted 8 lines
Quoted 6 lines
But from what i understand, you cannot use a 1000Base-X SFP, set the MAC to 100Mbps, and expect it to connect to a 100Base-FX SFP. So for me, the RTL8211FS should not be advertise 100Mbps and 1Gbps, it needs to talk to the SFP figure out exactly what it is, and only advertise the one mode which is supported.
It is the RTL8211FS firmware bug. This patch is for workaround this issue.
So if it is advertising both 100Mbps and 1Gbps, we know the SFP is actually 1G, and we can remove the 100Mbps advertisement? That should then solve all the problems?
Quoted 8 lines
Quoted 5 lines
Right, that's what I proposed too, removing 1Gbps advertisement of the RTL8168H-internal PHY via userspace tool, e.g. ethtool. For me this is the cleanest solution. Adding a workaround for a firmware bug of a specific external PHY to the r8169 MAC driver would be somewhat hacky.
Thanks for your suggestions. But because it needs user to execute userspace tool. This workaround may not be accepted by our customer
In this case you can provide your customer with a downstream kernel including your patch.
Quoted 53 lines · Hau
Quoted 7 lines
Quoted 7 lines · Andrew Lunn
Quoted 6 lines · Hau
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 2 lines
In this application(rtl8168h + rtl8211fs) it also supports 100Mbps fiber
module.
Does RTL8211FS advertise 100Mbps and 1Gbps on the UTP/MDI
side
Quoted 8 lines
Quoted 8 lines
in
Quoted 7 lines
Quoted 7 lines
Quoted 6 lines
Quoted 6 lines
Quoted 3 lines
Quoted 1 line
case of a 100Mbps fiber module?
Yes.
I think in this case internal PHY and RTL8211FS would negotiate 1Gbps, not matching the speed of the 100Mbps fiber module. How does this work?
Quoted 8 lines
Quoted 8 lines
Quoted 4 lines
Quoted 4 lines
My mistake. With 100Mbps fiber module RTL8211FS will only advertise 100Mbps on the UTP/MDI side. With 1Gbps fiber module it will advertise both 100Mbps and 1Gbps. So issue will only happen with 1Gbps
fiber module.
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Fibre line side has no autoneg. Both ends need to be using the same speed, or the SERDES does not synchronise and does not
establish link.
Quoted 17 lines
Quoted 17 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
You can ask the SFP module what baud rate it supports, and then use anything up to that baud rate. I've got systems where the SFP is fast enough to support a 2.5Gbps link, so the MAC indicates both 2.5G and 1G, defaults to 2.5G, and fails to connect to a 1G link peer. You need to use ethtool to force it to the lower speed before the
link works.
Quoted 9 lines
Quoted 8 lines
Quoted 6 lines
But from what i understand, you cannot use a 1000Base-X SFP, set the MAC to 100Mbps, and expect it to connect to a 100Base-FX SFP. So for me, the RTL8211FS should not be advertise 100Mbps and 1Gbps, it needs to talk to the SFP figure out exactly what it is, and only advertise the one mode which is supported.
It is the RTL8211FS firmware bug. This patch is for workaround this issue.
Quoted 8 lines
Quoted 8 lines
Quoted 4 lines
So if it is advertising both 100Mbps and 1Gbps, we know the SFP is actually 1G, and we can remove the 100Mbps advertisement? That should then solve all the problems?
Right, that's what I proposed too, removing 1Gbps advertisement of the RTL8168H-internal PHY via userspace tool, e.g. ethtool. For me this is the cleanest solution. Adding a workaround for a firmware bug of a specific external PHY to the r8169 MAC driver would be somewhat
hacky.
Quoted 1 line
Quoted 1 line
Quoted 8 lines
Quoted 1 line
Thanks for your suggestions. But because it needs user to execute
userspace tool.
Quoted 2 lines
This workaround may not be accepted by our customer
In this case you can provide your customer with a downstream kernel including your patch.
Thanks. We will include it as one of the options.
------Please consider the environment before printing this e-mail.