Skip to contentSkip to conversation

sh: add support for sh7752evb board

PATCH New Shimoda 2 participants 2 messages Nov 5, 2012 – Nov 12, 2012

Subsystems (2)
SuperH Arm/actions semi architecture
lore
Share & tools
lore

Shimoda

#0 lore raw

PATCH 1/1 sh: add support for sh7752evb board

The R0P7752C00000RZ board has SH7752, 512MB DDR3-SDRAM, SPI ROM, Gigabit Ethernet, and eMMC.

This patch supports the following functions:
- 512MB DDR3-SDRAM, SCIF4, SPI ROM, Gigabit Ethernet, eMMC

Signed-off-by Yoshihiro Shimoda <[email protected]>
---
 MAINTAINERS                             |    1 +
 arch/sh/include/asm/cpu_sh4.h           |    2 +
 arch/sh/include/asm/cpu_sh7752.h        |  211 ++++++++++++++
 board/renesas/sh7752evb/Makefile        |   36 +++
 board/renesas/sh7752evb/lowlevel_init.S |  460 +++++++++++++++++++++++++++++++
 board/renesas/sh7752evb/sh7752evb.c     |  330 ++++++++++++++++++++++
 board/renesas/sh7752evb/spi-boot.c      |  116 ++++++++
 board/renesas/sh7752evb/u-boot.lds      |   97 +++++++
 boards.cfg                              |    1 +
 doc/README.sh7752evb                    |   67 +++++
 include/configs/sh7752evb.h             |  153 ++++++++++
 11 files changed, 1474 insertions(+), 0 deletions(-)
 create mode 100644 arch/sh/include/asm/cpu_sh7752.h
 create mode 100644 board/renesas/sh7752evb/Makefile
 create mode 100644 board/renesas/sh7752evb/lowlevel_init.S
 create mode 100644 board/renesas/sh7752evb/sh7752evb.c
 create mode 100644 board/renesas/sh7752evb/spi-boot.c
 create mode 100644 board/renesas/sh7752evb/u-boot.lds
 create mode 100644 doc/README.sh7752evb
 create mode 100644 include/configs/sh7752evb.h
MAINTAINERS +1 -0
index 2daee7d..d7f49e9 100644
@@ -1184,6 +1184,7 @@ Mark Jonas <[email protected]>
 Yoshihiro Shimoda <[email protected]>
 
 	MS7720SE	SH7720
+	R0P77520000RZ	SH7752
 	R0P77570030RL	SH7757
 	R0P77850011RL	SH7785
arch/sh/include/asm/cpu_sh4.h +2 -0
index f1f49fe..af5c56f 100644
@@ -48,6 +48,8 @@
 # include <asm/cpu_sh7724.h>
 #elif defined (CONFIG_CPU_SH7734)
 # include <asm/cpu_sh7734.h>
+#elif defined (CONFIG_CPU_SH7752)
+# include <asm/cpu_sh7752.h>
 #elif defined (CONFIG_CPU_SH7757)
 # include <asm/cpu_sh7757.h>
 #elif defined (CONFIG_CPU_SH7763)
arch/sh/include/asm/cpu_sh7752.h new file +211 -0

211 lines not on this page · raw message

board/renesas/sh7752evb/Makefile new file +36 -0
new file mode 100644
index 0000000..196c992
@@ -0,0 +1,36 @@
+#
+# Copyright (C) 2012  Yoshihiro Shimoda <[email protected]>
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS	:= sh7752evb.o spi-boot.o
+SOBJS	:= lowlevel_init.o
+
+$(LIB):	$(obj).depend $(COBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(COBJS) $(SOBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
board/renesas/sh7752evb/lowlevel_init.S new file +460 -0

460 lines not on this page · raw message

board/renesas/sh7752evb/sh7752evb.c new file +330 -0

330 lines not on this page · raw message

board/renesas/sh7752evb/spi-boot.c new file +116 -0

116 lines not on this page · raw message

board/renesas/sh7752evb/u-boot.lds new file +97 -0

97 lines not on this page · raw message

boards.cfg +1 -0
index 0ecd1b8..151cb2f 100644
@@ -1078,6 +1078,7 @@ ecovec                       sh          sh4         ecovec              renesas
 MigoR                        sh          sh4         MigoR               renesas        -
 r2dplus                      sh          sh4         r2dplus             renesas        -
 r7780mp                      sh          sh4         r7780mp             renesas        -
+sh7752evb                    sh          sh4         sh7752evb           renesas        -
 sh7757lcr                    sh          sh4         sh7757lcr           renesas        -
 sh7763rdp                    sh          sh4         sh7763rdp           renesas        -
 sh7785lcr                    sh          sh4         sh7785lcr           renesas        -
doc/README.sh7752evb new file +67 -0

67 lines not on this page · raw message

include/configs/sh7752evb.h new file +153 -0

153 lines not on this page · raw message

Signature · 1 line
1.7.1
Applied
#1 lore raw

PATCH 1/1 sh: add support for sh7752evb board

Applied, thanks.

Best regards,
Nobuhiro

Quoted 1,586 lines · Yoshihiro

The R0P7752C00000RZ board has SH7752, 512MB DDR3-SDRAM, SPI ROM, Gigabit Ethernet, and eMMC.

This patch supports the following functions:
- 512MB DDR3-SDRAM, SCIF4, SPI ROM, Gigabit Ethernet, eMMC

Signed-off-by Yoshihiro Shimoda <[email protected]>
---
 MAINTAINERS                             |    1 +
 arch/sh/include/asm/cpu_sh4.h           |    2 +
 arch/sh/include/asm/cpu_sh7752.h        |  211 ++++++++++++++
 board/renesas/sh7752evb/Makefile        |   36 +++
 board/renesas/sh7752evb/lowlevel_init.S |  460 +++++++++++++++++++++++++++++++
 board/renesas/sh7752evb/sh7752evb.c     |  330 ++++++++++++++++++++++
 board/renesas/sh7752evb/spi-boot.c      |  116 ++++++++
 board/renesas/sh7752evb/u-boot.lds      |   97 +++++++
 boards.cfg                              |    1 +
 doc/README.sh7752evb                    |   67 +++++
 include/configs/sh7752evb.h             |  153 ++++++++++
 11 files changed, 1474 insertions(+), 0 deletions(-)
 create mode 100644 arch/sh/include/asm/cpu_sh7752.h
 create mode 100644 board/renesas/sh7752evb/Makefile
 create mode 100644 board/renesas/sh7752evb/lowlevel_init.S
 create mode 100644 board/renesas/sh7752evb/sh7752evb.c
 create mode 100644 board/renesas/sh7752evb/spi-boot.c
 create mode 100644 board/renesas/sh7752evb/u-boot.lds
 create mode 100644 doc/README.sh7752evb
 create mode 100644 include/configs/sh7752evb.h
MAINTAINERS +1 -0
index 2daee7d..d7f49e9 100644
@@ -1184,6 +1184,7 @@ Mark Jonas <[email protected]>
 Yoshihiro Shimoda <[email protected]>
 
        MS7720SE        SH7720
+       R0P77520000RZ   SH7752
        R0P77570030RL   SH7757
        R0P77850011RL   SH7785
arch/sh/include/asm/cpu_sh4.h +2 -0
index f1f49fe..af5c56f 100644
@@ -48,6 +48,8 @@
 # include <asm/cpu_sh7724.h>
 #elif defined (CONFIG_CPU_SH7734)
 # include <asm/cpu_sh7734.h>
+#elif defined (CONFIG_CPU_SH7752)
+# include <asm/cpu_sh7752.h>
 #elif defined (CONFIG_CPU_SH7757)
 # include <asm/cpu_sh7757.h>
 #elif defined (CONFIG_CPU_SH7763)
arch/sh/include/asm/cpu_sh7752.h new file +211 -0
new file mode 100644
index 0000000..f0ad0e8
@@ -0,0 +1,211 @@
+/*
+ * Copyright (C) 2012  Renesas Solutions Corp.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#ifndef _ASM_CPU_SH7752_H_
+#define _ASM_CPU_SH7752_H_
+
+#define CCR            0xFF00001C
+#define WTCNT          0xFFCC0000
+#define CCR_CACHE_INIT 0x0000090b
+#define CACHE_OC_NUM_WAYS      1
+
+#ifndef __ASSEMBLY__           /* put C only stuff in this section */
+/* MMU */
+struct mmu_regs {
+       unsigned int    reserved[4];
+       unsigned int    mmucr;
+};
+#define MMU_BASE       ((struct mmu_regs *)0xff000000)
+
+/* Watchdog */
+#define WTCSR0         0xffcc0002
+#define WRSTCSR_R      0xffcc0003
+#define WRSTCSR_W      0xffcc0002
+#define WTCSR_PREFIX           0xa500
+#define WRSTCSR_PREFIX         0x6900
+#define WRSTCSR_WOVF_PREFIX    0x9600
+
+/* SCIF */
+#define SCIF0_BASE     0xfe4b0000      /* The real name is SCIF2 */
+#define SCIF1_BASE     0xfe4c0000      /* The real name is SCIF3 */
+#define SCIF2_BASE     0xfe4d0000      /* The real name is SCIF4 */
+
+/* TMU0 */
+#define TMU_BASE        0xFE430000
+
+/* ETHER, GETHER MAC address */
+struct ether_mac_regs {
+       unsigned int    reserved[114];
+       unsigned int    mahr;
+       unsigned int    reserved2;
+       unsigned int    malr;
+};
+#define GETHER0_MAC_BASE       ((struct ether_mac_regs *)0xfee0400)
+#define GETHER1_MAC_BASE       ((struct ether_mac_regs *)0xfee0c00)
+#define ETHER0_MAC_BASE                ((struct ether_mac_regs *)0xfef0000)
+#define ETHER1_MAC_BASE                ((struct ether_mac_regs *)0xfef0800)
+
+/* GETHER */
+struct gether_control_regs {
+       unsigned int    gbecont;
+};
+#define GETHER_CONTROL_BASE    ((struct gether_control_regs *)0xffc10100)
+#define GBECONT_RMII1          0x00020000
+#define GBECONT_RMII0          0x00010000
+
+/* SerMux */
+struct sermux_regs {
+       unsigned char   smr0;
+       unsigned char   smr1;
+       unsigned char   smr2;
+       unsigned char   smr3;
+       unsigned char   smr4;
+       unsigned char   smr5;
+};
+#define SERMUX_BASE    ((struct sermux_regs *)0xfe470000)
+
+
+/* USB0/1 */
+struct usb_common_regs {
+       unsigned short  reserved[129];
+       unsigned short  suspmode;
+};
+#define USB0_COMMON_BASE       ((struct usb_common_regs *)0xfe450000)
+#define USB1_COMMON_BASE       ((struct usb_common_regs *)0xfe4f0000)
+
+struct usb0_phy_regs {
+       unsigned short  reset;
+       unsigned short  reserved[4];
+       unsigned short  portsel;
+};
+#define USB0_PHY_BASE          ((struct usb0_phy_regs *)0xfe5f0000)
+
+struct usb1_port_regs {
+       unsigned int    port1sel;
+       unsigned int    reserved;
+       unsigned int    usb1intsts;
+};
+#define USB1_PORT_BASE         ((struct usb1_port_regs *)0xfe4f2000)
+
+struct usb1_alignment_regs {
+       unsigned int    ehcidatac;      /* 0xfe4fe018 */
+       unsigned int    reserved[63];
+       unsigned int    ohcidatac;
+};
+#define USB1_ALIGNMENT_BASE    ((struct usb1_alignment_regs *)0xfe4fe018)
+
+/* GPIO */
+struct gpio_regs {
+       unsigned short  pacr;
+       unsigned short  pbcr;
+       unsigned short  pccr;
+       unsigned short  pdcr;
+       unsigned short  pecr;
+       unsigned short  pfcr;
+       unsigned short  pgcr;
+       unsigned short  phcr;
+       unsigned short  picr;
+       unsigned short  pjcr;
+       unsigned short  pkcr;
+       unsigned short  plcr;
+       unsigned short  pmcr;
+       unsigned short  pncr;
+       unsigned short  pocr;
+       unsigned short  reserved;
+       unsigned short  pqcr;
+       unsigned short  prcr;
+       unsigned short  pscr;
+       unsigned short  ptcr;
+       unsigned short  pucr;
+       unsigned short  pvcr;
+       unsigned short  pwcr;
+       unsigned short  pxcr;
+       unsigned short  pycr;
+       unsigned short  pzcr;
+       unsigned char   padr;
+       unsigned char   reserved_a;
+       unsigned char   pbdr;
+       unsigned char   reserved_b;
+       unsigned char   pcdr;
+       unsigned char   reserved_c;
+       unsigned char   pddr;
+       unsigned char   reserved_d;
+       unsigned char   pedr;
+       unsigned char   reserved_e;
+       unsigned char   pfdr;
+       unsigned char   reserved_f;
+       unsigned char   pgdr;
+       unsigned char   reserved_g;
+       unsigned char   phdr;
+       unsigned char   reserved_h;
+       unsigned char   pidr;
+       unsigned char   reserved_i;
+       unsigned char   pjdr;
+       unsigned char   reserved_j;
+       unsigned char   pkdr;
+       unsigned char   reserved_k;
+       unsigned char   pldr;
+       unsigned char   reserved_l;
+       unsigned char   pmdr;
+       unsigned char   reserved_m;
+       unsigned char   pndr;
+       unsigned char   reserved_n;
+       unsigned char   podr;
+       unsigned char   reserved_o;
+       unsigned char   ppdr;
+       unsigned char   reserved_p;
+       unsigned char   pqdr;
+       unsigned char   reserved_q;
+       unsigned char   prdr;
+       unsigned char   reserved_r;
+       unsigned char   psdr;
+       unsigned char   reserved_s;
+       unsigned char   ptdr;
+       unsigned char   reserved_t;
+       unsigned char   pudr;
+       unsigned char   reserved_u;
+       unsigned char   pvdr;
+       unsigned char   reserved_v;
+       unsigned char   pwdr;
+       unsigned char   reserved_w;
+       unsigned char   pxdr;
+       unsigned char   reserved_x;
+       unsigned char   pydr;
+       unsigned char   reserved_y;
+       unsigned char   pzdr;
+       unsigned char   reserved_z;
+       unsigned short  ncer;
+       unsigned short  ncmcr;
+       unsigned short  nccsr;
+       unsigned char   reserved2[2];
+       unsigned short  psel0;          /* +0x70 */
+       unsigned short  psel1;
+       unsigned short  psel2;
+       unsigned short  psel3;
+       unsigned short  psel4;
+       unsigned short  psel5;
+       unsigned short  psel6;
+       unsigned short  reserved3[2];
+       unsigned short  psel7;
+};
+#define GPIO_BASE      ((struct gpio_regs *)0xffec0000)
+
+#endif /* ifndef __ASSEMBLY__ */
+#endif /* _ASM_CPU_SH7752_H_ */
board/renesas/sh7752evb/Makefile new file +36 -0
new file mode 100644
index 0000000..196c992
@@ -0,0 +1,36 @@
+#
+# Copyright (C) 2012  Yoshihiro Shimoda <[email protected]>
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+
+include $(TOPDIR)/config.mk
+
+LIB    = $(obj)lib$(BOARD).o
+
+COBJS  := sh7752evb.o spi-boot.o
+SOBJS  := lowlevel_init.o
+
+$(LIB):        $(obj).depend $(COBJS) $(SOBJS)
+       $(call cmd_link_o_target, $(COBJS) $(SOBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
board/renesas/sh7752evb/lowlevel_init.S new file +460 -0
new file mode 100644
index 0000000..73c8ac4
@@ -0,0 +1,460 @@
+/*
+ * Copyright (C) 2012  Renesas Solutions Corp.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/processor.h>
+#include <asm/macro.h>
+
+.macro or32, addr, data
+       mov.l \addr, r1
+       mov.l \data, r0
+       mov.l @r1, r2
+       or    r2, r0
+       mov.l r0, @r1
+.endm
+
+.macro wait_DBCMD
+       mov.l   DBWAIT_A, r0
+       mov.l   @r0, r1
+.endm
+
+       .global lowlevel_init
+       .section        .spiboot1.text
+       .align  2
+
+lowlevel_init:
+       /*------- GPIO -------*/
+       write16 PDCR_A, PDCR_D          ! SPI0
+       write16 PGCR_A, PGCR_D          ! SPI0, GETHER MDIO gate(PTG1)
+       write16 PJCR_A, PJCR_D          ! SCIF4
+       write16 PTCR_A, PTCR_D          ! STATUS
+       write16 PSEL1_A, PSEL1_D        ! SPI0
+       write16 PSEL2_A, PSEL2_D        ! SPI0
+       write16 PSEL5_A, PSEL5_D        ! STATUS
+
+       bra     exit_gpio
+       nop
+
+       .align  2
+
+/*------- GPIO -------*/
+PDCR_A:                .long   0xffec0006
+PGCR_A:                .long   0xffec000c
+PJCR_A:                .long   0xffec0012
+PTCR_A:                .long   0xffec0026
+PSEL1_A:       .long   0xffec0072
+PSEL2_A:       .long   0xffec0074
+PSEL5_A:       .long   0xffec007a
+
+PDCR_D:                .long   0x0000
+PGCR_D:                .long   0x0004
+PJCR_D:                .long   0x0000
+PTCR_D:                .long   0x0000
+PSEL1_D:       .long   0x0000
+PSEL2_D:       .long   0x3000
+PSEL5_D:       .long   0x0ffc
+
+       .align  2
+
+exit_gpio:
+       mov     #0, r14
+       mova    2f, r0
+       mov.l   PC_MASK, r1
+       tst     r0, r1
+       bf      2f
+
+       bra     exit_pmb
+       nop
+
+       .align  2
+
+/* If CPU runs on SDRAM (PC=0x5???????) or not. */
+PC_MASK:       .long   0x20000000
+
+2:
+       mov     #1, r14
+
+       mov.l   EXPEVT_A, r0
+       mov.l   @r0, r0
+       mov.l   EXPEVT_POWER_ON_RESET, r1
+       cmp/eq  r0, r1
+       bt      1f
+
+       /*
+        * If EXPEVT value is manual reset or tlb multipul-hit,
+        * initialization of DDR3IF is not necessary.
+        */
+       bra     exit_ddr
+       nop
+
+1:
+       /*------- Reset -------*/
+       write32 MRSTCR0_A, MRSTCR0_D
+       write32 MRSTCR1_A, MRSTCR1_D
+
+       /* For Core Reset */
+       mov.l   DBACEN_A, r0
+       mov.l   @r0, r0
+       cmp/eq  #0, r0
+       bt      3f
+
+       /*
+        * If DBACEN == 1(DBSC was already enabled), we have to avoid the
+        * initialization of DDR3-SDRAM.
+        */
+       bra     exit_ddr
+       nop
+
+3:
+       /*------- DDR3IF -------*/
+       /* oscillation stabilization time */
+       wait_timer      WAIT_OSC_TIME
+
+       /* step 3 */
+       write32 DBCMD_A, DBCMD_RSTL_VAL
+       wait_timer      WAIT_30US
+
+       /* step 4 */
+       write32 DBCMD_A, DBCMD_PDEN_VAL
+
+       /* step 5 */
+       write32 DBKIND_A, DBKIND_D
+
+       /* step 6 */
+       write32 DBCONF_A, DBCONF_D
+       write32 DBTR0_A, DBTR0_D
+       write32 DBTR1_A, DBTR1_D
+       write32 DBTR2_A, DBTR2_D
+       write32 DBTR3_A, DBTR3_D
+       write32 DBTR4_A, DBTR4_D
+       write32 DBTR5_A, DBTR5_D
+       write32 DBTR6_A, DBTR6_D
+       write32 DBTR7_A, DBTR7_D
+       write32 DBTR8_A, DBTR8_D
+       write32 DBTR9_A, DBTR9_D
+       write32 DBTR10_A, DBTR10_D
+       write32 DBTR11_A, DBTR11_D
+       write32 DBTR12_A, DBTR12_D
+       write32 DBTR13_A, DBTR13_D
+       write32 DBTR14_A, DBTR14_D
+       write32 DBTR15_A, DBTR15_D
+       write32 DBTR16_A, DBTR16_D
+       write32 DBTR17_A, DBTR17_D
+       write32 DBTR18_A, DBTR18_D
+       write32 DBTR19_A, DBTR19_D
+       write32 DBRNK0_A, DBRNK0_D
+
+       /* step 7 */
+       write32 DBPDCNT3_A, DBPDCNT3_D
+
+       /* step 8 */
+       write32 DBPDCNT1_A, DBPDCNT1_D
+       write32 DBPDCNT2_A, DBPDCNT2_D
+       write32 DBPDLCK_A, DBPDLCK_D
+       write32 DBPDRGA_A, DBPDRGA_D
+       write32 DBPDRGD_A, DBPDRGD_D
+
+       /* step 9 */
+       wait_timer      WAIT_30US
+
+       /* step 10 */
+       write32 DBPDCNT0_A, DBPDCNT0_D
+
+       /* step 11 */
+       wait_timer      WAIT_30US
+       wait_timer      WAIT_30US
+
+       /* step 12 */
+       write32 DBCMD_A, DBCMD_WAIT_VAL
+       wait_DBCMD
+
+       /* step 13 */
+       write32 DBCMD_A, DBCMD_RSTH_VAL
+       wait_DBCMD
+
+       /* step 14 */
+       write32 DBCMD_A, DBCMD_WAIT_VAL
+       write32 DBCMD_A, DBCMD_WAIT_VAL
+       write32 DBCMD_A, DBCMD_WAIT_VAL
+       write32 DBCMD_A, DBCMD_WAIT_VAL
+
+       /* step 15 */
+       write32 DBCMD_A, DBCMD_PDXT_VAL
+
+       /* step 16 */
+       write32 DBCMD_A, DBCMD_MRS2_VAL
+
+       /* step 17 */
+       write32 DBCMD_A, DBCMD_MRS3_VAL
+
+       /* step 18 */
+       write32 DBCMD_A, DBCMD_MRS1_VAL
+
+       /* step 19 */
+       write32 DBCMD_A, DBCMD_MRS0_VAL
+
+       /* step 20 */
+       write32 DBCMD_A, DBCMD_ZQCL_VAL
+
+       write32 DBCMD_A, DBCMD_REF_VAL
+       write32 DBCMD_A, DBCMD_REF_VAL
+       wait_DBCMD
+
+       /* step 21 */
+       write32 DBADJ0_A, DBADJ0_D
+       write32 DBADJ1_A, DBADJ1_D
+       write32 DBADJ2_A, DBADJ2_D
+
+       /* step 22 */
+       write32 DBRFCNF0_A, DBRFCNF0_D
+       write32 DBRFCNF1_A, DBRFCNF1_D
+       write32 DBRFCNF2_A, DBRFCNF2_D
+
+       /* step 23 */
+       write32 DBCALCNF_A, DBCALCNF_D
+
+       /* step 24 */
+       write32 DBRFEN_A, DBRFEN_D
+       write32 DBCMD_A, DBCMD_SRXT_VAL
+
+       /* step 25 */
+       write32 DBACEN_A, DBACEN_D
+
+       /* step 26 */
+       wait_DBCMD
+
+       bra     exit_ddr
+       nop
+
+       .align 2
+
+EXPEVT_A:              .long   0xff000024
+EXPEVT_POWER_ON_RESET: .long   0x00000000
+
+/*------- Reset -------*/
+MRSTCR0_A:     .long   0xffd50030
+MRSTCR0_D:     .long   0xfe1ffe7f
+MRSTCR1_A:     .long   0xffd50034
+MRSTCR1_D:     .long   0xfff3ffff
+
+/*------- DDR3IF -------*/
+DBCMD_A:       .long   0xfe800018
+DBKIND_A:      .long   0xfe800020
+DBCONF_A:      .long   0xfe800024
+DBTR0_A:       .long   0xfe800040
+DBTR1_A:       .long   0xfe800044
+DBTR2_A:       .long   0xfe800048
+DBTR3_A:       .long   0xfe800050
+DBTR4_A:       .long   0xfe800054
+DBTR5_A:       .long   0xfe800058
+DBTR6_A:       .long   0xfe80005c
+DBTR7_A:       .long   0xfe800060
+DBTR8_A:       .long   0xfe800064
+DBTR9_A:       .long   0xfe800068
+DBTR10_A:      .long   0xfe80006c
+DBTR11_A:      .long   0xfe800070
+DBTR12_A:      .long   0xfe800074
+DBTR13_A:      .long   0xfe800078
+DBTR14_A:      .long   0xfe80007c
+DBTR15_A:      .long   0xfe800080
+DBTR16_A:      .long   0xfe800084
+DBTR17_A:      .long   0xfe800088
+DBTR18_A:      .long   0xfe80008c
+DBTR19_A:      .long   0xfe800090
+DBRNK0_A:      .long   0xfe800100
+DBPDCNT0_A:    .long   0xfe800200
+DBPDCNT1_A:    .long   0xfe800204
+DBPDCNT2_A:    .long   0xfe800208
+DBPDCNT3_A:    .long   0xfe80020c
+DBPDLCK_A:     .long   0xfe800280
+DBPDRGA_A:     .long   0xfe800290
+DBPDRGD_A:     .long   0xfe8002a0
+DBADJ0_A:      .long   0xfe8000c0
+DBADJ1_A:      .long   0xfe8000c4
+DBADJ2_A:      .long   0xfe8000c8
+DBRFCNF0_A:    .long   0xfe8000e0
+DBRFCNF1_A:    .long   0xfe8000e4
+DBRFCNF2_A:    .long   0xfe8000e8
+DBCALCNF_A:    .long   0xfe8000f4
+DBRFEN_A:      .long   0xfe800014
+DBACEN_A:      .long   0xfe800010
+DBWAIT_A:      .long   0xfe80001c
+
+WAIT_OSC_TIME: .long   6000
+WAIT_30US:     .long   13333
+
+DBCMD_RSTL_VAL:        .long   0x20000000
+DBCMD_PDEN_VAL:        .long   0x1000d73c
+DBCMD_WAIT_VAL:        .long   0x0000d73c
+DBCMD_RSTH_VAL:        .long   0x2100d73c
+DBCMD_PDXT_VAL:        .long   0x110000c8
+DBCMD_MRS0_VAL:        .long   0x28000930
+DBCMD_MRS1_VAL:        .long   0x29000004
+DBCMD_MRS2_VAL:        .long   0x2a000008
+DBCMD_MRS3_VAL:        .long   0x2b000000
+DBCMD_ZQCL_VAL:        .long   0x03000200
+DBCMD_REF_VAL: .long   0x0c000000
+DBCMD_SRXT_VAL:        .long   0x19000000
+DBKIND_D:      .long   0x00000007
+DBCONF_D:      .long   0x0f030a01
+DBTR0_D:       .long   0x00000007
+DBTR1_D:       .long   0x00000006
+DBTR2_D:       .long   0x00000000
+DBTR3_D:       .long   0x00000007
+DBTR4_D:       .long   0x00070007
+DBTR5_D:       .long   0x0000001b
+DBTR6_D:       .long   0x00000014
+DBTR7_D:       .long   0x00000005
+DBTR8_D:       .long   0x00000015
+DBTR9_D:       .long   0x00000006
+DBTR10_D:      .long   0x00000008
+DBTR11_D:      .long   0x00000007
+DBTR12_D:      .long   0x0000000e
+DBTR13_D:      .long   0x00000056
+DBTR14_D:      .long   0x00000006
+DBTR15_D:      .long   0x00000004
+DBTR16_D:      .long   0x00150002
+DBTR17_D:      .long   0x000c0017
+DBTR18_D:      .long   0x00000200
+DBTR19_D:      .long   0x00000040
+DBRNK0_D:      .long   0x00000001
+DBPDCNT0_D:    .long   0x00000001
+DBPDCNT1_D:    .long   0x00000001
+DBPDCNT2_D:    .long   0x00000000
+DBPDCNT3_D:    .long   0x00004010
+DBPDLCK_D:     .long   0x0000a55a
+DBPDRGA_D:     .long   0x00000028
+DBPDRGD_D:     .long   0x00017100
+
+DBADJ0_D:      .long   0x00000000
+DBADJ1_D:      .long   0x00000000
+DBADJ2_D:      .long   0x18061806
+DBRFCNF0_D:    .long   0x000001ff
+DBRFCNF1_D:    .long   0x08001000
+DBRFCNF2_D:    .long   0x00000000
+DBCALCNF_D:    .long   0x0000ffff
+DBRFEN_D:      .long   0x00000001
+DBACEN_D:      .long   0x00000001
+
+       .align 2
+exit_ddr:
+#if defined(CONFIG_SH_32BIT)
+       /*------- set PMB -------*/
+       write32 PASCR_A,        PASCR_29BIT_D
+       write32 MMUCR_A,        MMUCR_D
+
+       /*****************************************************************
+        * ent  virt            phys            v       sz      c       wt
+        * 0    0xa0000000      0x00000000      1       128M    0       1
+        * 1    0xa8000000      0x48000000      1       128M    0       1
+        * 5    0x88000000      0x48000000      1       128M    1       1
+        */
+       write32 PMB_ADDR_SPIBOOT_A,     PMB_ADDR_SPIBOOT_D
+       write32 PMB_DATA_SPIBOOT_A,     PMB_DATA_SPIBOOT_D
+       write32 PMB_ADDR_DDR_C1_A,      PMB_ADDR_DDR_C1_D
+       write32 PMB_DATA_DDR_C1_A,      PMB_DATA_DDR_C1_D
+       write32 PMB_ADDR_DDR_N1_A,      PMB_ADDR_DDR_N1_D
+       write32 PMB_DATA_DDR_N1_A,      PMB_DATA_DDR_N1_D
+
+       write32 PMB_ADDR_ENTRY2,        PMB_ADDR_NOT_USE_D
+       write32 PMB_ADDR_ENTRY3,        PMB_ADDR_NOT_USE_D
+       write32 PMB_ADDR_ENTRY4,        PMB_ADDR_NOT_USE_D
+       write32 PMB_ADDR_ENTRY6,        PMB_ADDR_NOT_USE_D
+       write32 PMB_ADDR_ENTRY7,        PMB_ADDR_NOT_USE_D
+       write32 PMB_ADDR_ENTRY8,        PMB_ADDR_NOT_USE_D
+       write32 PMB_ADDR_ENTRY9,        PMB_ADDR_NOT_USE_D
+       write32 PMB_ADDR_ENTRY10,       PMB_ADDR_NOT_USE_D
+       write32 PMB_ADDR_ENTRY11,       PMB_ADDR_NOT_USE_D
+       write32 PMB_ADDR_ENTRY12,       PMB_ADDR_NOT_USE_D
+       write32 PMB_ADDR_ENTRY13,       PMB_ADDR_NOT_USE_D
+       write32 PMB_ADDR_ENTRY14,       PMB_ADDR_NOT_USE_D
+       write32 PMB_ADDR_ENTRY15,       PMB_ADDR_NOT_USE_D
+
+       write32 PASCR_A,        PASCR_INIT
+       mov.l   DUMMY_ADDR, r0
+       icbi    @r0
+#endif /* if defined(CONFIG_SH_32BIT) */
+
+exit_pmb:
+       /* CPU is running on ILRAM? */
+       mov     r14, r0
+       tst     #1, r0
+       bt      1f
+
+       mov.l   _stack_ilram, r15
+       mov.l   _spiboot_main, r0
+100:   bsrf    r0
+       nop
+
+       .align  2
+_spiboot_main: .long   (spiboot_main - (100b + 4))
+_stack_ilram:  .long   0xe5204000
+
+1:
+       write32 CCR_A,  CCR_D
+
+       rts
+        nop
+
+       .align 2
+
+#if defined(CONFIG_SH_32BIT)
+/*------- set PMB -------*/
+PMB_ADDR_SPIBOOT_A:    .long   PMB_ADDR_BASE(0)
+PMB_ADDR_DDR_N1_A:     .long   PMB_ADDR_BASE(1)
+PMB_ADDR_DDR_C1_A:     .long   PMB_ADDR_BASE(5)
+PMB_ADDR_ENTRY2:       .long   PMB_ADDR_BASE(2)
+PMB_ADDR_ENTRY3:       .long   PMB_ADDR_BASE(3)
+PMB_ADDR_ENTRY4:       .long   PMB_ADDR_BASE(4)
+PMB_ADDR_ENTRY6:       .long   PMB_ADDR_BASE(6)
+PMB_ADDR_ENTRY7:       .long   PMB_ADDR_BASE(7)
+PMB_ADDR_ENTRY8:       .long   PMB_ADDR_BASE(8)
+PMB_ADDR_ENTRY9:       .long   PMB_ADDR_BASE(9)
+PMB_ADDR_ENTRY10:      .long   PMB_ADDR_BASE(10)
+PMB_ADDR_ENTRY11:      .long   PMB_ADDR_BASE(11)
+PMB_ADDR_ENTRY12:      .long   PMB_ADDR_BASE(12)
+PMB_ADDR_ENTRY13:      .long   PMB_ADDR_BASE(13)
+PMB_ADDR_ENTRY14:      .long   PMB_ADDR_BASE(14)
+PMB_ADDR_ENTRY15:      .long   PMB_ADDR_BASE(15)
+
+PMB_ADDR_SPIBOOT_D:    .long   mk_pmb_addr_val(0xa0)
+PMB_ADDR_DDR_C1_D:     .long   mk_pmb_addr_val(0x88)
+PMB_ADDR_DDR_N1_D:     .long   mk_pmb_addr_val(0xa8)
+PMB_ADDR_NOT_USE_D:    .long   0x00000000
+
+PMB_DATA_SPIBOOT_A:    .long   PMB_DATA_BASE(0)
+PMB_DATA_DDR_N1_A:     .long   PMB_DATA_BASE(1)
+PMB_DATA_DDR_C1_A:     .long   PMB_DATA_BASE(5)
+
+/*                                             ppn   ub v s1 s0  c  wt */
+PMB_DATA_SPIBOOT_D:    .long   mk_pmb_data_val(0x00, 0, 1, 1, 0, 0, 1)
+PMB_DATA_DDR_C1_D:     .long   mk_pmb_data_val(0x48, 0, 1, 1, 0, 1, 1)
+PMB_DATA_DDR_N1_D:     .long   mk_pmb_data_val(0x48, 1, 1, 1, 0, 0, 1)
+
+PASCR_A:               .long   0xff000070
+DUMMY_ADDR:            .long   0xa0000000
+PASCR_29BIT_D:         .long   0x00000000
+PASCR_INIT:            .long   0x80000080
+MMUCR_A:               .long   0xff000010
+MMUCR_D:               .long   0x00000004      /* clear ITLB */
+#endif /* CONFIG_SH_32BIT */
+
+CCR_A:         .long   CCR
+CCR_D:         .long   CCR_CACHE_INIT
board/renesas/sh7752evb/sh7752evb.c new file +330 -0
new file mode 100644
index 0000000..e996593
@@ -0,0 +1,330 @@
+/*
+ * Copyright (C) 2012  Renesas Solutions Corp.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <asm/mmc.h>
+#include <spi_flash.h>
+
+int checkboard(void)
+{
+       puts("BOARD: SH7752 evaluation board (R0P7752C00000RZ)\n");
+
+       return 0;
+}
+
+static void init_gpio(void)
+{
+       struct gpio_regs *gpio = GPIO_BASE;
+       struct sermux_regs *sermux = SERMUX_BASE;
+
+       /* GPIO */
+       writew(0x0000, &gpio->pacr);    /* GETHER */
+       writew(0x0001, &gpio->pbcr);    /* INTC */
+       writew(0x0000, &gpio->pccr);    /* PWMU, INTC */
+       writew(0xeaff, &gpio->pecr);    /* GPIO */
+       writew(0x0000, &gpio->pfcr);    /* WDT */
+       writew(0x0000, &gpio->phcr);    /* SPI1 */
+       writew(0x0000, &gpio->picr);    /* SDHI */
+       writew(0x0003, &gpio->pkcr);    /* SerMux */
+       writew(0x0000, &gpio->plcr);    /* SerMux */
+       writew(0x0000, &gpio->pmcr);    /* RIIC */
+       writew(0x0000, &gpio->pncr);    /* USB, SGPIO */
+       writew(0x0000, &gpio->pocr);    /* SGPIO */
+       writew(0xd555, &gpio->pqcr);    /* GPIO */
+       writew(0x0000, &gpio->prcr);    /* RIIC */
+       writew(0x0000, &gpio->pscr);    /* RIIC */
+       writeb(0x00, &gpio->pudr);
+       writew(0x5555, &gpio->pucr);    /* Debug LED */
+       writew(0x0000, &gpio->pvcr);    /* RSPI */
+       writew(0x0000, &gpio->pwcr);    /* EVC */
+       writew(0x0000, &gpio->pxcr);    /* LBSC */
+       writew(0x0000, &gpio->pycr);    /* LBSC */
+       writew(0x0000, &gpio->pzcr);    /* eMMC */
+       writew(0xfe00, &gpio->psel0);
+       writew(0xff00, &gpio->psel3);
+       writew(0x771f, &gpio->psel4);
+       writew(0x00ff, &gpio->psel6);
+       writew(0xfc00, &gpio->psel7);
+
+       writeb(0x10, &sermux->smr0);    /* SMR0: SerMux mode 0 */
+}
+
+static void init_usb_phy(void)
+{
+       struct usb_common_regs *common0 = USB0_COMMON_BASE;
+       struct usb_common_regs *common1 = USB1_COMMON_BASE;
+       struct usb0_phy_regs *phy = USB0_PHY_BASE;
+       struct usb1_port_regs *port = USB1_PORT_BASE;
+       struct usb1_alignment_regs *align = USB1_ALIGNMENT_BASE;
+
+       writew(0x0100, &phy->reset);            /* set reset */
+       /* port0 = USB0, port1 = USB1 */
+       writew(0x0002, &phy->portsel);
+       writel(0x0001, &port->port1sel);        /* port1 = Host */
+       writew(0x0111, &phy->reset);            /* clear reset */
+
+       writew(0x4000, &common0->suspmode);
+       writew(0x4000, &common1->suspmode);
+
+#if defined(__LITTLE_ENDIAN)
+       writel(0x00000000, &align->ehcidatac);
+       writel(0x00000000, &align->ohcidatac);
+#endif
+}
+
+static void init_gether_mdio(void)
+{
+       struct gpio_regs *gpio = GPIO_BASE;
+
+       writew(readw(&gpio->pgcr) | 0x0004, &gpio->pgcr);
+       writeb(readb(&gpio->pgdr) | 0x02, &gpio->pgdr); /* Use ET0-MDIO */
+}
+
+static void set_mac_to_sh_giga_eth_register(int channel, char *mac_string)
+{
+       struct ether_mac_regs *ether;
+       unsigned char mac[6];
+       unsigned long val;
+
+       eth_parse_enetaddr(mac_string, mac);
+
+       if (!channel)
+               ether = GETHER0_MAC_BASE;
+       else
+               ether = GETHER1_MAC_BASE;
+
+       val = (mac[0] << 24) | (mac[1] << 16) | (mac[2] << 8) | mac[3];
+       writel(val, &ether->mahr);
+       val = (mac[4] << 8) | mac[5];
+       writel(val, &ether->malr);
+}
+
+/*****************************************************************
+ * This PMB must be set on this timing. The lowlevel_init is run on
+ * Area 0(phys 0x00000000), so we have to map it.
+ *
+ * The new PMB table is following:
+ * ent virt            phys            v       sz      c       wt
+ * 0   0xa0000000      0x40000000      1       128M    0       1
+ * 1   0xa8000000      0x48000000      1       128M    0       1
+ * 2   0xb0000000      0x50000000      1       128M    0       1
+ * 3   0xb8000000      0x58000000      1       128M    0       1
+ * 4   0x80000000      0x40000000      1       128M    1       1
+ * 5   0x88000000      0x48000000      1       128M    1       1
+ * 6   0x90000000      0x50000000      1       128M    1       1
+ * 7   0x98000000      0x58000000      1       128M    1       1
+ */
+static void set_pmb_on_board_init(void)
+{
+       struct mmu_regs *mmu = MMU_BASE;
+
+       /* clear ITLB */
+       writel(0x00000004, &mmu->mmucr);
+
+       /* delete PMB for SPIBOOT */
+       writel(0, PMB_ADDR_BASE(0));
+       writel(0, PMB_DATA_BASE(0));
+
+       /* add PMB for SDRAM(0x40000000 - 0x47ffffff) */
+       /*                      ppn  ub v s1 s0  c  wt */
+       writel(mk_pmb_addr_val(0xa0), PMB_ADDR_BASE(0));
+       writel(mk_pmb_data_val(0x40, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(0));
+       writel(mk_pmb_addr_val(0xb0), PMB_ADDR_BASE(2));
+       writel(mk_pmb_data_val(0x50, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(2));
+       writel(mk_pmb_addr_val(0xb8), PMB_ADDR_BASE(3));
+       writel(mk_pmb_data_val(0x58, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(3));
+       writel(mk_pmb_addr_val(0x80), PMB_ADDR_BASE(4));
+       writel(mk_pmb_data_val(0x40, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(4));
+       writel(mk_pmb_addr_val(0x90), PMB_ADDR_BASE(6));
+       writel(mk_pmb_data_val(0x50, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(6));
+       writel(mk_pmb_addr_val(0x98), PMB_ADDR_BASE(7));
+       writel(mk_pmb_data_val(0x58, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(7));
+}
+
+int board_init(void)
+{
+       init_gpio();
+       set_pmb_on_board_init();
+
+       init_usb_phy();
+       init_gether_mdio();
+
+       return 0;
+}
+
+int dram_init(void)
+{
+       DECLARE_GLOBAL_DATA_PTR;
+
+       gd->bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;
+       gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;
+       printf("DRAM:  %dMB\n", CONFIG_SYS_SDRAM_SIZE / (1024 * 1024));
+
+       return 0;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+       struct gpio_regs *gpio = GPIO_BASE;
+
+       writew(readw(&gpio->pgcr) | 0x0040, &gpio->pgcr);
+       writeb(readb(&gpio->pgdr) & ~0x08, &gpio->pgdr); /* Reset */
+       udelay(1);
+       writeb(readb(&gpio->pgdr) | 0x08, &gpio->pgdr); /* Release reset */
+       udelay(200);
+
+       return mmcif_mmc_init();
+}
+
+static int get_sh_eth_mac_raw(unsigned char *buf, int size)
+{
+       struct spi_flash *spi;
+       int ret;
+
+       spi = spi_flash_probe(0, 0, 1000000, SPI_MODE_3);
+       if (spi == NULL) {
+               printf("%s: spi_flash probe failed.\n", __func__);
+               return 1;
+       }
+
+       ret = spi_flash_read(spi, SH7752EVB_ETHERNET_MAC_BASE, size, buf);
+       if (ret) {
+               printf("%s: spi_flash read failed.\n", __func__);
+               spi_flash_free(spi);
+               return 1;
+       }
+       spi_flash_free(spi);
+
+       return 0;
+}
+
+static int get_sh_eth_mac(int channel, char *mac_string, unsigned char *buf)
+{
+       memcpy(mac_string, &buf[channel * (SH7752EVB_ETHERNET_MAC_SIZE + 1)],
+               SH7752EVB_ETHERNET_MAC_SIZE);
+       mac_string[SH7752EVB_ETHERNET_MAC_SIZE] = 0x00; /* terminate */
+
+       return 0;
+}
+
+static void init_ethernet_mac(void)
+{
+       char mac_string[64];
+       char env_string[64];
+       int i;
+       unsigned char *buf;
+
+       buf = malloc(256);
+       if (!buf) {
+               printf("%s: malloc failed.\n", __func__);
+               return;
+       }
+       get_sh_eth_mac_raw(buf, 256);
+
+       /* Gigabit Ethernet */
+       for (i = 0; i < SH7752EVB_ETHERNET_NUM_CH; i++) {
+               get_sh_eth_mac(i, mac_string, buf);
+               if (i == 0)
+                       setenv("ethaddr", mac_string);
+               else {
+                       sprintf(env_string, "eth%daddr", i);
+                       setenv(env_string, mac_string);
+               }
+               set_mac_to_sh_giga_eth_register(i, mac_string);
+       }
+
+       free(buf);
+}
+
+int board_late_init(void)
+{
+       init_ethernet_mac();
+
+       return 0;
+}
+
+int do_write_mac(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+       int i, ret;
+       char mac_string[256];
+       struct spi_flash *spi;
+       unsigned char *buf;
+
+       if (argc != 3) {
+               buf = malloc(256);
+               if (!buf) {
+                       printf("%s: malloc failed.\n", __func__);
+                       return 1;
+               }
+
+               get_sh_eth_mac_raw(buf, 256);
+
+               /* print current MAC address */
+               for (i = 0; i < SH7752EVB_ETHERNET_NUM_CH; i++) {
+                       get_sh_eth_mac(i, mac_string, buf);
+                       printf("GETHERC ch%d = %s\n", i, mac_string);
+               }
+               free(buf);
+               return 0;
+       }
+
+       /* new setting */
+       memset(mac_string, 0xff, sizeof(mac_string));
+       sprintf(mac_string, "%s\t%s",
+               argv[1], argv[2]);
+
+       /* write MAC data to SPI rom */
+       spi = spi_flash_probe(0, 0, 1000000, SPI_MODE_3);
+       if (!spi) {
+               printf("%s: spi_flash probe failed.\n", __func__);
+               return 1;
+       }
+
+       ret = spi_flash_erase(spi, SH7752EVB_ETHERNET_MAC_BASE_SPI,
+                               SH7752EVB_SPI_SECTOR_SIZE);
+       if (ret) {
+               printf("%s: spi_flash erase failed.\n", __func__);
+               return 1;
+       }
+
+       ret = spi_flash_write(spi, SH7752EVB_ETHERNET_MAC_BASE_SPI,
+                               sizeof(mac_string), mac_string);
+       if (ret) {
+               printf("%s: spi_flash write failed.\n", __func__);
+               spi_flash_free(spi);
+               return 1;
+       }
+       spi_flash_free(spi);
+
+       puts("The writing of the MAC address to SPI ROM was completed.\n");
+
+       return 0;
+}
+
+U_BOOT_CMD(
+       write_mac,      3,      1,      do_write_mac,
+       "write MAC address for GETHERC",
+       "[GETHERC ch0] [GETHERC ch1]\n"
+);
board/renesas/sh7752evb/spi-boot.c new file +116 -0
new file mode 100644
index 0000000..91565d4
@@ -0,0 +1,116 @@
+/*
+ * Copyright (C) 2012  Renesas Solutions Corp.
+ *
+ * This file is subject to the terms and conditions of the GNU Lesser
+ * General Public License.  See the file "COPYING.LIB" in the main
+ * directory of this archive for more details.
+ */
+
+#include <common.h>
+
+#define CONFIG_RAM_BOOT_PHYS   CONFIG_SYS_TEXT_BASE
+#define CONFIG_SPI_ADDR                0x00000000
+#define CONFIG_SPI_LENGTH      CONFIG_SYS_MONITOR_LEN
+#define CONFIG_RAM_BOOT                CONFIG_SYS_TEXT_BASE
+
+#define SPIWDMADR      0xFE001018
+#define SPIWDMCNTR     0xFE001020
+#define SPIDMCOR       0xFE001028
+#define SPIDMINTSR     0xFE001188
+#define SPIDMINTMR     0xFE001190
+
+#define SPIDMINTSR_DMEND       0x00000004
+
+#define TBR    0xFE002000
+#define RBR    0xFE002000
+
+#define CR1    0xFE002008
+#define CR2    0xFE002010
+#define CR3    0xFE002018
+#define CR4    0xFE002020
+
+/* CR1 */
+#define SPI_TBE                0x80
+#define SPI_TBF                0x40
+#define SPI_RBE                0x20
+#define SPI_RBF                0x10
+#define SPI_PFONRD     0x08
+#define SPI_SSDB       0x04
+#define SPI_SSD                0x02
+#define SPI_SSA                0x01
+
+/* CR2 */
+#define SPI_RSTF       0x80
+#define SPI_LOOPBK     0x40
+#define SPI_CPOL       0x20
+#define SPI_CPHA       0x10
+#define SPI_L1M0       0x08
+
+/* CR4 */
+#define SPI_TBEI       0x80
+#define SPI_TBFI       0x40
+#define SPI_RBEI       0x20
+#define SPI_RBFI       0x10
+#define SPI_SpiS0      0x02
+#define SPI_SSS                0x01
+
+#define spi_write(val, addr)   (*(volatile unsigned long *)(addr)) = val
+#define spi_read(addr)         (*(volatile unsigned long *)(addr))
+
+/* M25P80 */
+#define M25_READ       0x03
+
+#define __uses_spiboot2        __attribute__((section(".spiboot2.text")))
+static void __uses_spiboot2 spi_reset(void)
+{
+       int timeout = 0x00100000;
+
+       /* Make sure the last transaction is finalized */
+       spi_write(0x00, CR3);
+       spi_write(0x02, CR1);
+       while (!(spi_read(CR4) & SPI_SpiS0)) {
+               if (timeout-- < 0)
+                       break;
+       }
+       spi_write(0x00, CR1);
+
+       spi_write(spi_read(CR2) | SPI_RSTF, CR2);       /* fifo reset */
+       spi_write(spi_read(CR2) & ~SPI_RSTF, CR2);
+
+       spi_write(0, SPIDMCOR);
+}
+
+static void __uses_spiboot2 spi_read_flash(void *buf, unsigned long addr,
+                                          unsigned long len)
+{
+       spi_write(M25_READ, TBR);
+       spi_write((addr >> 16) & 0xFF, TBR);
+       spi_write((addr >> 8) & 0xFF, TBR);
+       spi_write(addr & 0xFF, TBR);
+
+       spi_write(SPIDMINTSR_DMEND, SPIDMINTSR);
+       spi_write((unsigned long)buf, SPIWDMADR);
+       spi_write(len & 0xFFFFFFE0, SPIWDMCNTR);
+       spi_write(1, SPIDMCOR);
+
+       spi_write(0xff, CR3);
+       spi_write(spi_read(CR1) | SPI_SSDB, CR1);
+       spi_write(spi_read(CR1) | SPI_SSA, CR1);
+
+       while (!(spi_read(SPIDMINTSR) & SPIDMINTSR_DMEND))
+               ;
+
+       /* Nagate SP0-SS0 */
+       spi_write(0, CR1);
+}
+
+void __uses_spiboot2 spiboot_main(void)
+{
+       void (*_start)(void) = (void *)CONFIG_SYS_TEXT_BASE;
+
+       spi_reset();
+       spi_read_flash((void *)CONFIG_RAM_BOOT_PHYS, CONFIG_SPI_ADDR,
+                       CONFIG_SPI_LENGTH);
+
+       _start();
+}
board/renesas/sh7752evb/u-boot.lds new file +97 -0
new file mode 100644
index 0000000..28449b6
@@ -0,0 +1,97 @@
+/*
+ * Copyright (C) 2007
+ * Nobuhiro Iwamatsu <[email protected]>
+ *
+ * Copyright (C) 2012
+ * Yoshihiro Shimoda <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-sh-linux", "elf32-sh-linux", "elf32-sh-linux")
+OUTPUT_ARCH(sh)
+ENTRY(_start)
+
+SECTIONS
+{
+       /*
+        * entry and reloct_dst will be provided via ldflags
+        */
+       . = .;
+
+       PROVIDE (_ftext = .);
+       PROVIDE (_fcode = .);
+       PROVIDE (_start = .);
+
+       .text :
+       {
+               KEEP(arch/sh/cpu/sh4/start.o            (.text))
+               *(.spiboot1.text)
+               *(.spiboot2.text)
+               . = ALIGN(8192);
+               common/env_embedded.o   (.ppcenv)
+               . = ALIGN(8192);
+               common/env_embedded.o   (.ppcenvr)
+               . = ALIGN(8192);
+               *(.text)
+               . = ALIGN(4);
+       } =0xFF
+       PROVIDE (_ecode = .);
+       .rodata :
+       {
+               *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
+               . = ALIGN(4);
+       }
+       PROVIDE (_etext = .);
+
+
+       PROVIDE (_fdata = .);
+       .data :
+       {
+               *(.data)
+               . = ALIGN(4);
+       }
+       PROVIDE (_edata = .);
+
+       PROVIDE (_fgot = .);
+       .got :
+       {
+               *(.got)
+               . = ALIGN(4);
+       }
+       PROVIDE (_egot = .);
+
+       .u_boot_list : {
+               #include <u-boot.lst>
+       }
+
+       PROVIDE (reloc_dst_end = .);
+       /* _reloc_dst_end = .; */
+
+       PROVIDE (bss_start = .);
+       PROVIDE (__bss_start = .);
+       .bss (NOLOAD) :
+       {
+               *(.bss)
+               . = ALIGN(4);
+       }
+       PROVIDE (bss_end = .);
+
+       PROVIDE (__bss_end__ = .);
+}
boards.cfg +1 -0
index 0ecd1b8..151cb2f 100644
@@ -1078,6 +1078,7 @@ ecovec                       sh          sh4         ecovec              renesas
 MigoR                        sh          sh4         MigoR               renesas        -
 r2dplus                      sh          sh4         r2dplus             renesas        -
 r7780mp                      sh          sh4         r7780mp             renesas        -
+sh7752evb                    sh          sh4         sh7752evb           renesas        -
 sh7757lcr                    sh          sh4         sh7757lcr           renesas        -
 sh7763rdp                    sh          sh4         sh7763rdp           renesas        -
 sh7785lcr                    sh          sh4         sh7785lcr           renesas        -
doc/README.sh7752evb new file +67 -0
new file mode 100644
index 0000000..c1fb54c
@@ -0,0 +1,67 @@
+========================================
+Renesas R0P7752C00000RZ board
+========================================
+
+This board specification:
+=========================
+
+The R0P7752C00000RZ(board config name:sh7752evb) has the following device:
+
+ - SH7752 (SH-4A)
+ - DDR3-SDRAM 512MB
+ - SPI ROM 8MB
+ - Gigabit Ethernet controllers
+ - eMMC 4GB
+
+
+Configuration for This board:
+=============================
+
+You can select the configuration as follows:
+
+ - make sh7752evb_config
+
+
+This board specific command:
+============================
+
+This board has the following its specific command:
+
+ - write_mac
+
+
+1. write_mac
+
+You can write MAC address to SPI ROM.
+
+ Usage 1) Write MAC address
+
+   write_mac [GETHERC ch0] [GETHERC ch1]
+
+       For example)
+        => write_mac 74:90:50:00:33:9e 74:90:50:00:33:9f
+               *) We have to input the command as a single line
+                  (without carriage return)
+               *) We have to reset after input the command.
+
+ Usage 2) Show current data
+
+   write_mac
+
+       For example)
+               => write_mac
+               GETHERC ch0 = 74:90:50:00:33:9e
+               GETHERC ch1 = 74:90:50:00:33:9f
+
+
+Update SPI ROM:
+============================
+
+1. Copy u-boot image to RAM area.
+2. Probe SPI device.
+   => sf probe 0
+   SF: Detected MX25L6405D with page size 64KiB, total 8 MiB
+3. Erase SPI ROM.
+   => sf erase 0 80000
+4. Write u-boot image to SPI ROM.
+   => sf write 0x48000000 0 80000
include/configs/sh7752evb.h new file +153 -1
new file mode 100644
index 0000000..bf6bd4d
@@ -0,0 +1,153 @@
+/*
+ * Configuation settings for the sh7752evb board
+ *
+ * Copyright (C) 2012 Renesas Solutions Corp.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __SH7752EVB_H
+#define __SH7752EVB_H
+
+#undef DEBUG
+#define CONFIG_SH              1
+#define CONFIG_SH4A            1
+#define CONFIG_SH_32BIT                1
+#define CONFIG_CPU_SH7752      1
+#define CONFIG_SH7752EVB       1
+
+#define CONFIG_SYS_TEXT_BASE   0x5ff80000
+#define CONFIG_SYS_LDSCRIPT    "board/renesas/sh7752evb/u-boot.lds"
+
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_DFL
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_MD5SUM
+#define CONFIG_MD5
+#define CONFIG_CMD_LOADS
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_DOS_PARTITION
+#define CONFIG_MAC_PARTITION
+
+#define CONFIG_BAUDRATE                115200
+#define CONFIG_BOOTDELAY       3
+#define CONFIG_BOOTARGS                "console=ttySC2,115200 root=/dev/nfs ip=dhcp"
+
+#define CONFIG_VERSION_VARIABLE
+#undef CONFIG_SHOW_BOOT_PROGRESS
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_AUTO_COMPLETE
+
+/* MEMORY */
+#define SH7752EVB_SDRAM_BASE           (0x40000000)
+#define SH7752EVB_SDRAM_SIZE           (512 * 1024 * 1024)
+
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_PROMPT              "=> "
+#define CONFIG_SYS_CBSIZE              256
+#define CONFIG_SYS_PBSIZE              256
+#define CONFIG_SYS_MAXARGS             16
+#define CONFIG_SYS_BARGSIZE            512
+#define CONFIG_SYS_BAUDRATE_TABLE      { 115200 }
+
+/* SCIF */
+#define CONFIG_SCIF_CONSOLE    1
+#define CONFIG_CONS_SCIF2      1
+#undef CONFIG_SYS_CONSOLE_INFO_QUIET
+#undef CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE
+
+#define CONFIG_SYS_MEMTEST_START       (SH7752EVB_SDRAM_BASE)
+#define CONFIG_SYS_MEMTEST_END         (CONFIG_SYS_MEMTEST_START + \
+                                        480 * 1024 * 1024)
+#undef CONFIG_SYS_ALT_MEMTEST
+#undef CONFIG_SYS_MEMTEST_SCRATCH
+#undef CONFIG_SYS_LOADS_BAUD_CHANGE
+
+#define CONFIG_SYS_SDRAM_BASE          (SH7752EVB_SDRAM_BASE)
+#define CONFIG_SYS_SDRAM_SIZE          (SH7752EVB_SDRAM_SIZE)
+#define CONFIG_SYS_LOAD_ADDR           (CONFIG_SYS_SDRAM_BASE + \
+                                        128 * 1024 * 1024)
+
+#define CONFIG_SYS_MONITOR_BASE                0x00000000
+#define CONFIG_SYS_MONITOR_LEN         (512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN          (4 * 1024 * 1024)
+#define CONFIG_SYS_BOOTMAPSZ           (8 * 1024 * 1024)
+
+/* FLASH */
+#define CONFIG_SYS_NO_FLASH
+
+/* Ether */
+#define CONFIG_SH_ETHER                        1
+#define CONFIG_SH_ETHER_USE_PORT       0
+#define CONFIG_SH_ETHER_PHY_ADDR       18
+#define CONFIG_SH_ETHER_CACHE_WRITEBACK        1
+#define CONFIG_SH_ETHER_USE_GETHER     1
+#define CONFIG_PHYLIB
+#define CONFIG_BITBANGMII
+#define CONFIG_BITBANGMII_MULTI
+#define CONFIG_SH_ETHER_PHY_MODE PHY_INTERFACE_MODE_RGMII
+#define CONFIG_PHY_VITESSE
+
+#define SH7752EVB_ETHERNET_MAC_BASE_SPI        0x00090000
+#define SH7752EVB_SPI_SECTOR_SIZE      (64 * 1024)
+#define SH7752EVB_ETHERNET_MAC_BASE    SH7752EVB_ETHERNET_MAC_BASE_SPI
+#define SH7752EVB_ETHERNET_MAC_SIZE    17
+#define SH7752EVB_ETHERNET_NUM_CH      2
+#define CONFIG_BOARD_LATE_INIT
+
+/* SPI */
+#define CONFIG_SH_SPI                  1
+#define CONFIG_SH_SPI_BASE             0xfe002000
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO       1
+#define CONFIG_SPI_FLASH_MACRONIX      1
+
+/* MMCIF */
+#define CONFIG_MMC                     1
+#define CONFIG_GENERIC_MMC             1
+#define CONFIG_SH_MMCIF                        1
+#define CONFIG_SH_MMCIF_ADDR           0xffcb0000
+#define CONFIG_SH_MMCIF_CLK            48000000
+
+/* ENV setting */
+#define CONFIG_ENV_IS_EMBEDDED
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SECT_SIZE   (64 * 1024)
+#define CONFIG_ENV_ADDR                (0x00080000)
+#define CONFIG_ENV_OFFSET      (CONFIG_ENV_ADDR)
+#define CONFIG_ENV_OVERWRITE   1
+#define CONFIG_ENV_SIZE                (CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE)
+#define CONFIG_EXTRA_ENV_SETTINGS                              \
+               "netboot=bootp; bootm\0"
+
+/* Board Clock */
+#define CONFIG_SYS_CLK_FREQ    48000000
+#define CONFIG_SYS_TMU_CLK_DIV 4
+#define CONFIG_SYS_HZ          1000
+#endif /* __SH7752EVB_H */
--

1.7.1

Signature · 3 lines
Nobuhiro Iwamatsu
   iwamatsu at {nigauri.org / debian.org}
   GPG ID: 40AD1FA6