Add support for the OLED in the CFA10036
Subsystems (3)
v6 cover Add support for the OLED in the CFA10036
Hi everyone,
This patchset adds support for the solomon SSD1307 OLED controller present in the CFA-10036 board.
It first adds the framebuffer driver for this controller, and then the needed bits to enable it in the cfa10036 dts.
Considering that the driver has been around since almost three months now, and I have not received any comments on the framebuffer part, I'd very much like it to be included in 3.8 if possible.
Thanks,
Maxime
Changes from v5:
* Fixed bogus reset code
Maxime Ripard (2):
video: Add support for the Solomon SSD1307 OLED Controller
ARM: dts: mxs: add oled support for the cfa-10036
.../devicetree/bindings/video/ssd1307fb.txt | 24 ++ arch/arm/boot/dts/imx28-cfa10036.dts | 19 + drivers/video/Kconfig | 13 + drivers/video/Makefile | 1 + drivers/video/ssd1307fb.c | 407 ++++++++++++++++++++ 5 files changed, 464 insertions(+) create mode 100644 Documentation/devicetree/bindings/video/ssd1307fb.txt create mode 100644 drivers/video/ssd1307fb.c
Signature · 1 line
1.7.9.5
PATCH v6 1/2 video: Add support for the Solomon SSD1307 OLED Controller
This patch adds support for the Solomon SSD1307 OLED controller found on the Crystalfontz CFA10036 board.
This controller can drive a display with a resolution up to 128x39 and can operate over I2C or SPI.
The current driver has only been tested on the CFA-10036, that is using this controller over I2C to driver a 96x16 OLED screen.
--- .../devicetree/bindings/video/ssd1307fb.txt | 24 ++ drivers/video/Kconfig | 13 + drivers/video/Makefile | 1 + drivers/video/ssd1307fb.c | 407 ++++++++++++++++++++ 4 files changed, 445 insertions(+) create mode 100644 Documentation/devicetree/bindings/video/ssd1307fb.txt create mode 100644 drivers/video/ssd1307fb.c
Documentation/devicetree/bindings/video/ssd1307fb.txt new file +24 -0
@@ -0,0 +1,24 @@ +* Solomon SSD1307 Framebuffer Driver + +Required properties: + - compatible: Should be "solomon,ssd1307fb-<bus>". The only supported bus for + now is i2c. + - reg: Should contain address of the controller on the I2C bus. Most likely + 0x3c or 0x3d + - pwm: Should contain the pwm to use according to the OF device tree PWM + specification [0] + - reset-gpios: Should contain the GPIO used to reset the OLED display + +Optional properties: + - reset-active-low: Is the reset gpio is active on physical low? + +[0]: Documentation/devicetree/bindings/pwm/pwm.txt + +Examples: +ssd1307: oled at 3c { + compatible = "solomon,ssd1307fb-i2c"; + reg = <0x3c>; + pwms = <&pwm 4 3000>; + reset-gpios = <&gpio2 7>; + reset-active-low; +};
drivers/video/Kconfig +13 -0
@@ -2442,4 +2442,17 @@ config FB_SH_MOBILE_MERAM Up to 4 memory channels can be configured, allowing 4 RGB or 2 YCbCr framebuffers to be configured. +config FB_SSD1307 + tristate "Solomon SSD1307 framebuffer support" + depends on FB && I2C + select FB_SYS_FOPS + select FB_SYS_FILLRECT + select FB_SYS_COPYAREA + select FB_SYS_IMAGEBLIT + select FB_DEFERRED_IO + select PWM + help + This driver implements support for the Solomon SSD1307 + OLED controller over I2C. + endmenu
drivers/video/Makefile +1 -0
@@ -161,6 +161,7 @@ obj-$(CONFIG_FB_BFIN_7393) += bfin_adv7393fb.o obj-$(CONFIG_FB_MX3) += mx3fb.o obj-$(CONFIG_FB_DA8XX) += da8xx-fb.o obj-$(CONFIG_FB_MXS) += mxsfb.o +obj-$(CONFIG_FB_SSD1307) += ssd1307fb.o # the test framebuffer is last obj-$(CONFIG_FB_VIRTUAL) += vfb.o
drivers/video/ssd1307fb.c new file +407 -0
407 lines not on this page · raw message
Signature · 1 line
1.7.9.5
PATCH v6 2/2 ARM: dts: mxs: add oled support for the cfa-10036
In reply to Maxime Ripard--- arch/arm/boot/dts/imx28-cfa10036.dts | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)
arch/arm/boot/dts/imx28-cfa10036.dts +19 -0
@@ -33,11 +33,30 @@ }; apbx at 80040000 { + pwm: pwm at 80064000 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm4_pins_a>; + status = "okay"; + }; + duart: serial at 80074000 { pinctrl-names = "default"; pinctrl-0 = <&duart_pins_b>; status = "okay"; }; + + i2c0: i2c at 80058000 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_b>; + status = "okay"; + + ssd1307: oled at 3c { + compatible = "solomon,ssd1307fb-i2c"; + reg = <0x3c>; + pwms = <&pwm 4 3000>; + reset-gpios = <&gpio2 7 0>; + }; + }; }; };
Signature · 1 line
1.7.9.5
PATCH v6 2/2 ARM: dts: mxs: add oled support for the cfa-10036
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hi Shawn,
Le 31/10/2012 10:12, Maxime Ripard a ?crit :
Quoted 10 lines
Signed-off-by Maxime Ripard <[email protected]> Cc:Brian Lilly <[email protected]> ---
arch/arm/boot/dts/imx28-cfa10036.dts| 19 +++++++++++++++++++ 1
file changed, 19 insertions(+)(quoted diff) +0
-0
b/arch/arm/boot/dts/imx28-cfa10036.dtsindex c03a577..816cae9 100644 ---a/arch/arm/boot/dts/imx28-cfa10036.dts+++b/arch/arm/boot/dts/imx28-cfa10036.dts@@ -33,11 +33,30 @@ };
Quoted 8 lines
apbx at 80040000 { + pwm: pwm at 80064000 { + pinctrl-names =
"default"; + pinctrl-0 = <&pwm4_pins_a>; + status = "okay"; +
}; + duart: serial at 80074000 { pinctrl-names = "default"; pinctrl-0
= <&duart_pins_b>; status = "okay"; }; + + i2c0: i2c at 80058000 { +
pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_b>; +
status = "okay"; + + ssd1307: oled at 3c { + compatible =
"solomon,ssd1307fb-i2c"; + reg = <0x3c>; + pwms = <&pwm 4
3000>; + reset-gpios = <&gpio2 7 0>; + }; + }; }; };
Would you consider merging this patch? Andrew Morton merged the driver into its tree
(http://marc.info/?l=linux-fbdev&m=135336761530731&w=2)
Thanks,
Maxime
- --
Maxime Ripard, Free Electrons
Kernel, drivers, real-time and embedded Linux development, consulting, training and support.
http://free-electrons.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Mozilla - http://www.enigmail.net/
iEYEARECAAYFAlCsl7MACgkQGxsu9jQV9nZtJwCfR9c2SnwK1hzAU2F+xptFqg9x 2+0An3YrhNMXSZaPwPcJwc3Bnwy+FSqe
=mjpV
-----END PGP SIGNATURE-----
PATCH 2/2 ARM: dts: mxs: add oled support for the cfa-10036
Quoted 4 lines · Maxime Ripard
Would you consider merging this patch?
Andrew Morton merged the driver into its tree
(http://marc.info/?l=linux-fbdev&m=135336761530731&w=2)
Just applied, thanks.
v6 cover Add support for the OLED in the CFA10036
In reply to Maxime RipardPing?
Le 31/10/2012 10:12, Maxime Ripard a ?crit :
Quoted 31 lines
Hi everyone,
This patchset adds support for the solomon SSD1307 OLED controller present in the CFA-10036 board.
It first adds the framebuffer driver for this controller, and then the needed bits to enable it in the
cfa10036dts.Considering that the driver has been around since almost three months now, and I have not received any comments on the framebuffer part, I'd very much like it to be included in 3.8 if possible.
Thanks,
MaximeChanges from v5:
* Fixed bogus reset codeMaxime Ripard (2):
video: Add support for the Solomon SSD1307 OLED Controller
ARM: dts: mxs: add oled support for the cfa-10036.../devicetree/bindings/video/ssd1307fb.txt | 24 ++ arch/arm/boot/dts/imx28-cfa10036.dts | 19 + drivers/video/Kconfig | 13 + drivers/video/Makefile | 1 + drivers/video/ssd1307fb.c | 407 ++++++++++++++++++++ 5 files changed, 464 insertions(+) create mode 100644 Documentation/devicetree/bindings/video/ssd1307fb.txt create mode 100644 drivers/video/ssd1307fb.c
Signature · 4 lines
Maxime Ripard, Free Electrons Kernel, drivers, real-time and embedded Linux development, consulting, training and support. http://free-electrons.com