grub problems since upgrading build host to CentOS 6.3
We updated our build host to CentOS 6.3 which apparently has a newer host gcc.
Our crosstools are set for x86_64 target, and we know about grub not being supported for 64-bit compiler (Bug 5024). This newer gcc and/or binutils might be to blame.
The problem shows when we try to install it - we see this:
grub> device (hd0) /dev/sdb
grub> root (hd0,1)
Filesystem type is ext2fs, partition type 0x83
grub> setup (hd0)
Checking if "/boot/grub/stage1" exists... no
Checking if "/grub/stage1" exists... no
Error 15: File not found
grub>
But 'stage1' and all the others are indeed present on the root partition at /boot/grub/.
It's important to us to be able to build grub as needed in case we have to modify any networking hardware support, so falling back to using older binaries is not optimal. We're wondering if anyone else has gotten around this in a CentOS 6.3 build environment.
-Joe
Quoted 14 lines · Joe Lorenz
We updated our build host to CentOS 6.3 which apparently has a newer host gcc.
Our crosstools are set for
x86_64target, and we know about grub not being supported for 64-bit compiler (Bug 5024). This newer gcc and/or binutils might be to blame.The problem shows when we try to install it - we see this:
grub> device (hd0)
/dev/sdb
grub> root (hd0,1)
Filesystem type is ext2fs, partition type0x83
grub> setup (hd0)
Checking if "/boot/grub/stage1" exists... no
Checking if "/grub/stage1" exists... no
Quoted 4 lines
Error 15: File not found
grub>But 'stage1' and all the others are indeed present on the root partition at
/boot/grub/.
Let me try to understand what you're doing.
- You have a buildroot config that includes grub.
- You build on a pre-6.3 machine, boot the resulting image, run grub.
- grub finds /boot/grub/stage1 on /dev/sdb
- You build on a 6.3 machine, boot the resulting image, run grub.
- grub doesn't find /boot/grub/stage1 on /dev/sdb
Is that correct? Sounds weird... Can grub find any files on
(hd0,1)?
Quoted 4 lines
It's important to us to be able to build grub as needed in case we have to modify any networking hardware support, so falling back to using older binaries is not optimal. We're wondering if anyone else has gotten around this in a CentOS 6.3 build environment.
You could add grub2 to your local buildroot - see
http://patchwork.ozlabs.org/patch/191813/
Needs work, of course, but worked for me. grub2 is much better at cross-
compiling than grub.
Regards,
Arnout
Signature · 6 lines
Arnout Vandecappelle arnout at mind be Senior Embedded Software Architect +32-16-286540 Essensium/Mind http://www.mind.be G.Geenslaan 9, 3001 Leuven, Belgium BE 872 984 063 RPR Leuven LinkedIn profile: http://www.linkedin.com/in/arnoutvandecappelle GPG fingerprint: 7CB5 E4CC 6C2E EFD4 6E3D A754 F963 ECAB 2450 2F1F
Quoted 31 lines · Arnout Vandecappelle
Quoted 17 lines · Joe Lorenz
We updated our build host to CentOS 6.3 which apparently has a newer host gcc.
Our crosstools are set for
x86_64target, and we know about grub not being supported for 64-bit compiler (Bug 5024).
This newer gcc and/or binutils might be to blame.The problem shows when we try to install it - we see this:
grub> device (hd0)
/dev/sdb
grub> root (hd0,1)
Filesystem type is ext2fs, partition type0x83
grub> setup (hd0)
Checking if "/boot/grub/stage1" exists... no
Checking if "/grub/stage1" exists... noQuoted 5 lines
Error 15: File not found
grub>But 'stage1' and all the others are indeed present on the root partition at
/boot/grub/.Let me try to understand what you're doing.
- You have a buildroot config that includes grub.
- You build on a pre-6.3 machine, boot the resulting image, run grub.
- grub finds/boot/grub/stage1on/dev/sdb
Quoted 7 lines
- You build on a 6.3 machine, boot the resulting image, run grub.
- grub doesn't find/boot/grub/stage1on/dev/sdbIs that correct? Sounds weird... Can grub find any files on
(hd0,1)?
Close. Grub is not finding files in /dev/sda2, when it did just fine when built on pre-6.3. In another setting we have /dev/sda1 (hd0,0) as the root partition and it does the same thing.
It is extremely weird. And to top it off, I'd say about once every 30 or so attempts, it *does* find the files and installs OK. I'm not a grub expert and haven't yet tried to trace or step through to see why this is happening.
We did have to make a change to the objcopy flags because the objcopy in the 6.3 binutils was somehow creating HUGE files (several hundred MB) when objcopy'ing the stage* files and grub binary itself. That seems resolved (I don't have the link to where we found that solution), but now we're left with this. I was hoping somebody out there is using CentOS 6.3 and might have run into this.
Quoted 8 lines
Quoted 6 lines
It's important to us to be able to build grub as needed in case we have to modify any networking hardware support, so
falling back to using older binaries is not optimal. We're wondering if anyone else has gotten around this in a CentOS
6.3 build environment.
Quoted 6 lines
You could add grub2 to your local buildroot - see
http://patchwork.ozlabs.org/patch/191813/Needs work, of course, but worked for me. grub2 is much better at cross-
compiling than grub.
Yes, we're considering that as a possibility. Grub fits our needs though - just wish it would work :-/
Thanks for the response - let me know if you think of anything to try.
Quoted 11 lines
Regards,
Arnout--
Arnout Vandecappelle arnout at mind be Senior Embedded Software Architect +32-16-286540 Essensium/Mind http://www.mind.be G.Geenslaan 9, 3001 Leuven, Belgium BE 872 984 063 RPR Leuven LinkedIn profile: http://www.linkedin.com/in/arnoutvandecappelle GPG fingerprint: 7CB5 E4CC 6C2E EFD4 6E3D A754 F963 ECAB 2450 2F1F