Add support for the snowball board

index 5d9783a..54cc841 100644
@@ -250,6 +250,7 @@ source "package/sane-backends/Config.in"
 source "package/sdparm/Config.in"
 source "package/setserial/Config.in"
 source "package/smartmontools/Config.in"
+source "package/snowball-hdmiservice/Config.in"
 source "package/sredird/Config.in"
 source "package/statserial/Config.in"
 source "package/sysstat/Config.in"

new file mode 100644
index 0000000..0ea7c81
@@ -0,0 +1,10 @@
+config BR2_PACKAGE_SNOWBALL_HDMISERVICE
+	bool "snowball-hdmiservice"
+	depends on BR2_TOOLCHAIN_HAS_THREADS	
+	help
+	  HDMI userspace control daemon
+
+	  This package contains the HDMI userspace control daemon for the 
+	  snowball board
+	  
+	  http://www.igloocommunity.org

41 lines not on this page · raw message

index 54cc841..d1c197a 100644
@@ -261,6 +261,7 @@ source "package/usb_modeswitch/Config.in"
 source "package/usb_modeswitch_data/Config.in"
 source "package/usbmount/Config.in"
 source "package/usbutils/Config.in"
+source "package/ux500-firmware/Config.in"
 source "package/wipe/Config.in"
 endmenu
 

new file mode 100644
index 0000000..7e8a94b
@@ -0,0 +1,7 @@
+config BR2_PACKAGE_UX500_FIRMWARE
+	bool "ux500-firmware"
+	help
+	  This package provides various binary firmware files (closed binary blobs)
+	  for the Azurewave AW-NH580 combo module (wifi, bt, gps).
+
+	  https://launchpad.net/~igloocommunity-maintainers/+archive/snowball/+files/

new file mode 100644
index 0000000..d354468
@@ -0,0 +1,22 @@
+#############################################################
+#
+# ux500-firmware
+#
+#############################################################
+UX500_FIRMWARE_VERSION = 1.1.3-6
+UX500_FIRMWARE_SOURCE = ux500-firmware_$(UX500_FIRMWARE_VERSION)linaro1.tar.gz
+UX500_FIRMWARE_SITE = https://launchpad.net/~igloocommunity-maintainers/+archive/snowball/+files/
+UX500_FIRMWARE_LICENSE = Snowball click-wrap license
+UX500_FIRMWARE_LICENSE_FILES = license.txt 
+UX500_FIRMWARE_REDISTRIBUTE = NO
+
+# The CG2900 linux driver has to load firmware named CG29XX_* but the firmware
+# filenames contained in this package are CG2900_* hence the code below
+define UX500_FIRMWARE_INSTALL_TARGET_CMDS
+	$(MAKE) -C $(@D) DESTDIR=$(TARGET_DIR) install
+	for f in $(TARGET_DIR)/lib/firmware/CG2900* ; do \
+		mv $$f $${f/CG2900/CG29XX}; \
+	done
+endef
+
+$(eval $(generic-package))

new file mode 100644
index 0000000..4e6fb51
@@ -0,0 +1,45 @@
+From 3d1a9b44b9dcd2c0f5d54c09596c96c0524d8340 Mon Sep 17 00:00:00 2001
+From: Gregory Hermant <[email protected]>
+Date: Tue, 13 Nov 2012 11:47:41 +0100
+Subject: [PATCH] trace-debug[stm]: Fix for BT/WLAN instability
+
+Pins under mop500_ske_pins array are used for different
+functionalities in snowball. Ex: GPIO161 pin configured
+for keypad here must stay configured as GPIO alternate
+function for operating PMU_EN pin of BT/WLAN chip in snowball.
+So forbid configuring these pins, for snowball
+
+Signed-off-by: Rajanikanth H.V <[email protected]>
+Signed-off-by: Gregory Hermant <[email protected]>
+---
+ arch/arm/mach-ux500/board-mop500-stm.c |    7 +++++--
+ 1 file changed, 5 insertions(+), 2 deletions(-)
+
+diff --git a/arch/arm/mach-ux500/board-mop500-stm.c b/arch/arm/mach-ux500/board-mop500-stm.c
+index 1bef2a0..532fb9e 100644
+--- a/arch/arm/mach-ux500/board-mop500-stm.c
++++ b/arch/arm/mach-ux500/board-mop500-stm.c
+@@ -121,7 +121,9 @@ static int stm_ste_disable_ape_on_mipi60(void)
+ 	if (retval)
+ 		STM_ERR("Failed to disable MIPI60\n");
+ 	else {
+-		retval = nmk_config_pins(ARRAY_AND_SIZE(mop500_ske_pins));
++		if (!machine_is_snowball())
++			retval = nmk_config_pins(
++				ARRAY_AND_SIZE(mop500_ske_pins));
+ 		if (retval)
+ 			STM_ERR("Failed to enable SKE gpio\n");
+ 	}
+@@ -314,7 +316,8 @@ static int stm_ste_connection(enum stm_connection_type con_type)
+ 		/* Enable altC3 on GPIO70-74 (STMMOD) and GPIO75-76 (UARTMOD) */
+ 		prcmu_enable_stm_mod_uart();
+ 		/* Enable APE on MIPI60 */
+-		retval = nmk_config_pins_sleep(ARRAY_AND_SIZE(mop500_ske_pins));
++		if (!machine_is_snowball())
++			retval = nmk_config_pins_sleep(ARRAY_AND_SIZE(mop500_ske_pins));
+ 		if (retval)
+ 			STM_ERR("Failed to disable SKE GPIO\n");
+ 		else {
+-- 
+1.7.9.5
+

index d1c197a..69f3056 100644
@@ -551,6 +551,7 @@ source "package/empty/Config.in"
 source "package/googlefontdirectory/Config.in"
 source "package/mobile-broadband-provider-info/Config.in"
 source "package/shared-mime-info/Config.in"
+source "package/snowball-init/Config.in"
 source "package/sound-theme-borealis/Config.in"
 source "package/sound-theme-freedesktop/Config.in"
 endmenu

new file mode 100644
index 0000000..906ff2d
@@ -0,0 +1,10 @@
+config BR2_PACKAGE_SNOWBALL_INIT
+	bool "snowball-init"
+	# Runtime dependency, needed by snowball startup script
+	select BR2_PACKAGE_BLUEZ_UTILS
+	select BR2_PACKAGE_UX500_FIRMWARE
+	help
+	  Snowball init scripts
+
+	  http://www.igloocommunity.org
+

new file mode 100644
index 0000000..278cacb
@@ -0,0 +1,15 @@
+#############################################################
+#
+# snowball-init
+#
+#############################################################
+SNOWBALL_INIT_VERSION = b064be21de25729039e5e54037bbdd2e25cfd5b7
+SNOWBALL_INIT_SITE = git://igloocommunity.org/git/bsp/snowball-init.git
+SNOWBALL_INIT_LICENSE = BSD-4c
+SNOWBALL_INIT_LICENSE_FILES = debian/copyright
+
+define SNOWBALL_INIT_INSTALL_TARGET_CMDS
+	$(INSTALL) -D -m 0755 $(@D)/snowball $(TARGET_DIR)/etc/init.d/S50snowball
+endef
+
+$(eval $(generic-package))

new file mode 100644
index 0000000..e80af5f
@@ -0,0 +1,106 @@
+From ac7992081abba87627c9e91735b3309584b48585 Mon Sep 17 00:00:00 2001
+From: Gregory Hermant <[email protected]>
+Date: Wed, 14 Nov 2012 14:27:02 +0100
+Subject: [PATCH] add support for the ST-Ericsson CG2900 GPS FM Bluetooth
+ combo controller
+
+
+Signed-off-by: Gregory Hermant <[email protected]>
+---
+ tools/hciattach.c |   22 +++++++++++++++-------
+ tools/hciattach.h |    1 +
+ 2 files changed, 16 insertions(+), 7 deletions(-)
+
+diff --git a/tools/hciattach.c b/tools/hciattach.c
+index e4d5aa1..7f08243 100644
+--- a/tools/hciattach.c
++++ b/tools/hciattach.c
+@@ -1066,6 +1066,11 @@ struct uart_t uart[] = {
+ 	{ "texasalt",   0x0000, 0x0000, HCI_UART_LL,   115200, 115200,
+ 				FLOW_CTL, DISABLE_PM, NULL, texasalt, NULL   },
+ 
++	/* ST-Ericsson CG2900 GPS FM Bluetooth combo controller */
++	{ "cg2900",     0x0000, 0x0000, HCI_UART_STE,  115200, 115200,
++				FLOW_CTL, DISABLE_PM, NULL, NULL     },
++
++
+ 	/* ST Microelectronics minikits based on STLC2410/STLC2415 */
+ 	{ "st",         0x0000, 0x0000, HCI_UART_H4,    57600, 115200,
+ 				FLOW_CTL, DISABLE_PM,  NULL, st       },
+@@ -1157,10 +1162,10 @@ static struct uart_t * get_by_type(char *type)
+ }
+ 
+ /* Initialize UART driver */
+-static int init_uart(char *dev, struct uart_t *u, int send_break, int raw)
++static int init_uart(char *dev, struct uart_t *u, int send_break, int raw, int line_disc)
+ {
+ 	struct termios ti;
+-	int fd, i;
++	int fd;
+ 	unsigned long flags = 0;
+ 
+ 	if (raw)
+@@ -1217,8 +1222,7 @@ static int init_uart(char *dev, struct uart_t *u, int send_break, int raw)
+ 	}
+ 
+ 	/* Set TTY to N_HCI line discipline */
+-	i = N_HCI;
+-	if (ioctl(fd, TIOCSETD, &i) < 0) {
++	if (ioctl(fd, TIOCSETD, &line_disc) < 0) {
+ 		perror("Can't set line discipline");
+ 		return -1;
+ 	}
+@@ -1243,7 +1247,7 @@ static void usage(void)
+ {
+ 	printf("hciattach - HCI UART driver initialization utility\n");
+ 	printf("Usage:\n");
+-	printf("\thciattach [-n] [-p] [-b] [-r] [-t timeout] [-s initial_speed] <tty> <type | id> [speed] [flow|noflow] [bdaddr]\n");
++	printf("\thciattach [-n] [-p] [-a line_disc_nr] [-b] [-r] [-t timeout] [-s initial_speed] <tty> <type | id> [speed] [flow|noflow] [bdaddr]\n");
+ 	printf("\thciattach -l\n");
+ }
+ 
+@@ -1252,6 +1256,7 @@ int main(int argc, char *argv[])
+ 	struct uart_t *u = NULL;
+ 	int detach, printpid, raw, opt, i, n, ld, err;
+ 	int to = 10;
++	int line_disc = N_HCI;
+ 	int init_speed = 0;
+ 	int send_break = 0;
+ 	pid_t pid;
+@@ -1264,8 +1269,11 @@ int main(int argc, char *argv[])
+ 	printpid = 0;
+ 	raw = 0;
+ 
+-	while ((opt=getopt(argc, argv, "bnpt:s:lr")) != EOF) {
++	while ((opt=getopt(argc, argv, "bnpt:s:lra:")) != EOF) {
+ 		switch(opt) {
++		case 'a':
++                        line_disc = atoi(optarg);
++                        break;
+ 		case 'b':
+ 			send_break = 1;
+ 			break;
+@@ -1381,7 +1389,7 @@ int main(int argc, char *argv[])
+ 	alarm(to);
+ 	bcsp_max_retries = to;
+ 
+-	n = init_uart(dev, u, send_break, raw);
++	n = init_uart(dev, u, send_break, raw, line_disc);
+ 	if (n < 0) {
+ 		perror("Can't initialize device");
+ 		exit(1);
+diff --git a/tools/hciattach.h b/tools/hciattach.h
+index fed0d11..09b534d 100644
+--- a/tools/hciattach.h
++++ b/tools/hciattach.h
+@@ -39,6 +39,7 @@
+ #define HCI_UART_H4DS	3
+ #define HCI_UART_LL	4
+ #define HCI_UART_ATH3K  5
++#define HCI_UART_STE	6
+ 
+ #define HCI_UART_RAW_DEVICE	0
+ 
+-- 
+1.7.9.5
+

new file mode 100644
index 0000000..700be5d
@@ -0,0 +1,28 @@
+BR2_arm=y
+BR2_cortex_a9=y
+BR2_GCC_VERSION_4_7_X=y
+# BR2_SOFT_FLOAT is not set
+BR2_TOOLCHAIN_BUILDROOT_LARGEFILE=y
+BR2_TOOLCHAIN_BUILDROOT_INET_IPV6=y
+BR2_TOOLCHAIN_BUILDROOT_INET_RPC=y
+BR2_TOOLCHAIN_BUILDROOT_LOCALE=y
+BR2_TOOLCHAIN_BUILDROOT_CXX=y
+BR2_VFP_FLOAT=y
+BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_MDEV=y
+BR2_TARGET_GENERIC_GETTY_PORT="ttyAMA2"
+BR2_PACKAGE_BUSYBOX_SHOW_OTHERS=y
+BR2_PACKAGE_FBSET=y
+BR2_PACKAGE_SNOWBALL_HDMISERVICE=y
+BR2_PACKAGE_LIBNL=y
+BR2_PACKAGE_SNOWBALL_INIT=y
+BR2_PACKAGE_WPA_SUPPLICANT=y
+BR2_TARGET_ROOTFS_TAR_GZIP=y
+BR2_TARGET_UBOOT=y
+BR2_TARGET_UBOOT_BOARDNAME="snowball"
+BR2_LINUX_KERNEL=y
+BR2_LINUX_KERNEL_CUSTOM_GIT=y
+BR2_LINUX_KERNEL_CUSTOM_GIT_REPO_URL="git://igloocommunity.org/git/kernel/igloo-kernel.git"
+BR2_LINUX_KERNEL_CUSTOM_GIT_VERSION="stable-linux-ux500-3.4"
+BR2_LINUX_KERNEL_PATCH="board/calao/snowball/"
+BR2_LINUX_KERNEL_DEFCONFIG="u8500"
+BR2_LINUX_KERNEL_INSTALL_TARGET=y