Skip to contentSkip to conversation

powerpc/mpc85xx: Add BSC9132/BSC9232 processor support

PATCH Superseded Prabhakar Kushwaha 2 participants 3 messages Jan 15, 2013 – Jan 24, 2013 PowerPC

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 powerpc/mpc85xx: Add BSC9132/BSC9232 processor support

The BSC9132 is a highly integrated device that targets the evolving Microcell, Picocell, and Enterprise-Femto base station market subsegments.

The BSC9132 device combines Power Architecture e500 and DSP StarCore SC3850 core technologies with MAPLE-B2P baseband acceleration processing elements to address the need for a high performance, low cost, integrated solution that handles all required processing layers without the need for an external device except for an RF transceiver or, in a Micro base station configuration, a host device that handles the L3/L4 and handover between sectors.

The BSC9132 SoC includes the following function and features:
- Power Architecture subsystem including two e500 processors with 512-Kbyte shared L2 cache
- Two StarCore SC3850 DSP subsystems, each with a 512-Kbyte private L2 cache
- 32 Kbyte of shared M3 memory
- The Multi Accelerator Platform Engine for Pico BaseStation Baseband Processing (MAPLE-B2P)
- Two DDR3/3L memory interfaces with 32-bit data width (40 bits including ECC), up to 1333 MHz data rate
- Dedicated security engine featuring trusted boot
- Two DMA controllers
- OCNDMA with four bidirectional channels
- SysDMA with sixteen bidirectional channels
- Interfaces
- Four-lane SerDes PHY
- PCI Express controller complies with the PEX Specification-Rev 2.0
- Two Common Public Radio Interface (CPRI) controller lanes
- High-speed USB 2.0 host and device controller with ULPI interface
- Enhanced secure digital (SD/MMC) host controller (eSDHC)
- Antenna interface controller (AIC), supporting four industry standard JESD207/four custom ADI RF interfaces
- ADI lanes support both full duplex FDD support & half duplex TDD
- Universal Subscriber Identity Module (USIM) interface that facilitates communication to SIM cards or Eurochip pre-paid phone cards
- Two DUART, two eSPI, and two I2C controllers
- Integrated Flash memory controller (IFC)
- GPIO
- Sixteen 32-bit timers

---
Changes for v2: Incorporated Timur's review comments
- Removed SVR_9132_E as it is not required as part of

	following commit
	48f6a5c348453fc3ab33aaa91e5e4198a28678ff
 arch/powerpc/cpu/mpc85xx/Makefile         |    2 +
 arch/powerpc/cpu/mpc85xx/bsc9132_serdes.c |   96 +++++++++++++++++++++++++++++
 arch/powerpc/cpu/mpc8xxx/cpu.c            |    3 +
 arch/powerpc/include/asm/config_mpc85xx.h |   15 +++++
 arch/powerpc/include/asm/immap_85xx.h     |   25 +++++++-
 arch/powerpc/include/asm/processor.h      |    2 +
 6 files changed, 141 insertions(+), 2 deletions(-)
 create mode 100644 arch/powerpc/cpu/mpc85xx/bsc9132_serdes.c
arch/powerpc/cpu/mpc85xx/Makefile +2 -0
index 4c2b104..cb1f604 100644
@@ -85,6 +85,7 @@ COBJS-$(CONFIG_PPC_P5040)	+= ddr-gen3.o
 COBJS-$(CONFIG_PPC_T4240)	+= ddr-gen3.o
 COBJS-$(CONFIG_PPC_B4860)	+= ddr-gen3.o
 COBJS-$(CONFIG_BSC9131)		+= ddr-gen3.o
+COBJS-$(CONFIG_BSC9132)		+= ddr-gen3.o
 
 COBJS-$(CONFIG_CPM2)	+= ether_fcc.o
 COBJS-$(CONFIG_OF_LIBFDT) += fdt.o
@@ -135,6 +136,7 @@ COBJS-$(CONFIG_PPC_P5020) += p5020_serdes.o
 COBJS-$(CONFIG_PPC_P5040) += p5040_serdes.o
 COBJS-$(CONFIG_PPC_T4240) += t4240_serdes.o
 COBJS-$(CONFIG_PPC_B4860) += b4860_serdes.o
+COBJS-$(CONFIG_BSC9132) += bsc9132_serdes.o
 
 COBJS-y	+= cpu.o
 COBJS-y	+= cpu_init.o
arch/powerpc/cpu/mpc85xx/bsc9132_serdes.c new file +96 -0

96 lines not on this page · raw message

arch/powerpc/cpu/mpc8xxx/cpu.c +3 -0
index e8613be..03fd2fb 100644
@@ -86,6 +86,9 @@ static struct cpu_type cpu_type_list[] = {
 	CPU_TYPE_ENTRY(B4220, B4220, 0),
 	CPU_TYPE_ENTRY(BSC9130, 9130, 1),
 	CPU_TYPE_ENTRY(BSC9131, 9131, 1),
+	CPU_TYPE_ENTRY(BSC9132, 9132, 2),
+	CPU_TYPE_ENTRY(BSC9132, 9132_E, 2),
+	CPU_TYPE_ENTRY(BSC9232, 9232, 2),
 #elif defined(CONFIG_MPC86xx)
 	CPU_TYPE_ENTRY(8610, 8610, 1),
 	CPU_TYPE_ENTRY(8641, 8641, 2),
arch/powerpc/include/asm/config_mpc85xx.h +15 -0
index 0b9638b..4b6c172 100644
@@ -493,6 +493,21 @@
 #define CONFIG_SYS_FSL_ERRATUM_IFC_A003399
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
 
+#elif defined(CONFIG_BSC9132)
+#define CONFIG_MAX_CPUS			2
+#define CONFIG_SYS_PPC_E500_DEBUG_TLB	3
+#define CONFIG_FSL_SDHC_V2_3
+#define CONFIG_SYS_FSL_NUM_LAWS		12
+#define CONFIG_TSECV2
+#define CONFIG_SYS_FSL_SEC_COMPAT	4
+#define CONFIG_NUM_DDR_CONTROLLERS	2
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_FSL_ERRATUM_IFC_A003399
+#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
+#define CONFIG_SYS_FSL_ESDHC_P1010_BROKEN_SDCLK
+#define CONFIG_SYS_FSL_PCIE_COMPAT	"fsl,qoriq-pcie-v2.2"
+
 #elif defined(CONFIG_PPC_T4240)
 #define CONFIG_SYS_PPC64		/* 64-bit core */
 #define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
arch/powerpc/include/asm/immap_85xx.h +23 -2
index 296b549..ab4abc2 100644
@@ -2150,7 +2150,7 @@ typedef struct ccsr_gur {
 #define MPC85xx_PORPLLSR_DDR_RATIO	0x3e000000
 #define MPC85xx_PORPLLSR_DDR_RATIO_SHIFT	25
 #else
-#ifdef CONFIG_BSC9131
+#if defined(CONFIG_BSC9131) || defined(CONFIG_BSC9132)
 #define MPC85xx_PORPLLSR_DDR_RATIO	0x00003f00
 #else
 #define MPC85xx_PORPLLSR_DDR_RATIO	0x00003e00
@@ -2164,6 +2164,11 @@ typedef struct ccsr_gur {
 	u32	porbmsr;	/* POR boot mode status */
 #define MPC85xx_PORBMSR_HA		0x00070000
 #define MPC85xx_PORBMSR_HA_SHIFT	16
+#define MPC85XX_PORBMSR_ROMLOC_SHIFT	24
+#define PORBMSR_ROMLOC_SPI	0x6
+#define PORBMSR_ROMLOC_SDHC	0x7
+#define PORBMSR_ROMLOC_NAND_2K	0x9
+#define PORBMSR_ROMLOC_NOR	0xf
 	u32	porimpscr;	/* POR I/O impedance status & control */
 	u32	pordevsr;	/* POR I/O device status regsiter */
 #if defined(CONFIG_P1017) || defined(CONFIG_P1023)
@@ -2188,6 +2193,9 @@ typedef struct ccsr_gur {
 #if defined(CONFIG_P1010)
 #define MPC85xx_PORDEVSR_IO_SEL		0x00600000
 #define MPC85xx_PORDEVSR_IO_SEL_SHIFT	21
+#elif defined(CONFIG_BSC9132)
+#define MPC85xx_PORDEVSR_IO_SEL		0x00FE0000
+#define MPC85xx_PORDEVSR_IO_SEL_SHIFT	17
 #else
 #define MPC85xx_PORDEVSR_IO_SEL		0x00780000
 #define MPC85xx_PORDEVSR_IO_SEL_SHIFT	19
@@ -2345,6 +2353,10 @@ typedef struct ccsr_gur {
 #define MPC85xx_PMUXCR_SPI1_CS3_dbg_adi2_rxen	0x00000002
 #define MPC85xx_PMUXCR_SPI1_CS3_GPO76		0x00000003
 #endif
+#ifdef CONFIG_BSC9132
+#define MPC85xx_PMUXCR0_SIM_SEL_MASK	0x0003b000
+#define MPC85xx_PMUXCR0_SIM_SEL		0x00014000
+#endif
 	u32	pmuxcr2;	/* Alt. function signal multiplex control 2 */
 #if defined(CONFIG_P1010) || defined(CONFIG_P1014)
 #define MPC85xx_PMUXCR2_UART_GPIO		0x40000000
@@ -2375,6 +2387,7 @@ typedef struct ccsr_gur {
 #define MPC85xx_PMUXCR2_ETSECUSB_MASK	0x001f8000
 #define MPC85xx_PMUXCR2_USB		0x00150000
 #endif
+#if defined(CONFIG_BSC9131) || defined(CONFIG_BSC9132)
 #if defined(CONFIG_BSC9131)
 #define MPC85xx_PMUXCR2_UART_CTS_B0_SIM_PD		0X40000000
 #define MPC85xx_PMUXCR2_UART_CTS_B0_DSP_TMS		0X80000000
@@ -2418,8 +2431,9 @@ typedef struct ccsr_gur {
 #define MPC85xx_PMUXCR2_ANT3_AGC_GPO53			0x00000004
 #define MPC85xx_PMUXCR2_ANT3_DO_TDM			0x00000001
 #define MPC85xx_PMUXCR2_ANT3_DO_GPIO46_49		0x00000002
+#endif
 	u32	pmuxcr3;
-
+#if defined(CONFIG_BSC9131)
 #define MPC85xx_PMUXCR3_ANT3_DO4_5_TDM			0x40000000
 #define MPC85xx_PMUXCR3_ANT3_DO4_5_GPIO_50_51		0x80000000
 #define MPC85xx_PMUXCR3_ANT3_DO6_7_TRIG_IN_SRESET_B	0x10000000
@@ -2434,6 +2448,13 @@ typedef struct ccsr_gur {
 #define MPC85xx_PMUXCR3_SPI2_CS3_GPO94			0x00040000
 #define MPC85xx_PMUXCR3_ANT2_AGC_RSVD			0x00010000
 #define MPC85xx_PMUXCR3_ANT2_GPO89			0x00030000
+#endif
+#ifdef CONFIG_BSC9132
+#define MPC85xx_PMUXCR3_USB_SEL_MASK	0x0000ff00
+#define MPC85xx_PMUXCR3_UART2_SEL	0x00005000
+#define MPC85xx_PMUXCR3_UART3_SEL_MASK	0xc0000000
+#define MPC85xx_PMUXCR3_UART3_SEL	0x40000000
+#endif
 	u32 pmuxcr4;
 #else
 	u8	res6[8];
arch/powerpc/include/asm/processor.h +2 -0
index 19fe250..8c91f08 100644
@@ -1113,6 +1113,8 @@
 
 #define SVR_9130	0x860001
 #define SVR_9131	0x860000
+#define SVR_9132	0x861000
+#define SVR_9232	0x861400
 
 #define SVR_Unknown	0xFFFFFF
 
Signature · 1 line
1.7.9.5
#1 lore raw

PATCH v2 1/1 powerpc/mpc85xx: Add BSC9132/BSC9232 processor support

Quoted 50 lines · Prabhakar Kushwaha

The BSC9132 is a highly integrated device that targets the evolving Microcell, Picocell, and Enterprise-Femto base station market subsegments.

The BSC9132 device combines Power Architecture e500 and DSP StarCore
SC3850
core technologies with MAPLE-B2P baseband acceleration processing elements to address the need for a high performance, low cost, integrated solution that handles all required processing layers without the need for an external device except for an RF transceiver or, in a Micro base station configuration, a host device that handles the L3/L4 and handover between sectors.

The BSC9132 SoC includes the following function and features:
- Power Architecture subsystem including two e500 processors with 512-Kbyte shared L2 cache
- Two StarCore SC3850 DSP subsystems, each with a 512-Kbyte private L2 cache
- 32 Kbyte of shared M3 memory
- The Multi Accelerator Platform Engine for Pico BaseStation Baseband Processing (MAPLE-B2P)
- Two DDR3/3L memory interfaces with 32-bit data width (40 bits
including
ECC), up to 1333 MHz data rate
- Dedicated security engine featuring trusted boot
- Two DMA controllers
- OCNDMA with four bidirectional channels
- SysDMA with sixteen bidirectional channels
- Interfaces
- Four-lane SerDes PHY
- PCI Express controller complies with the PEX
Specification-Rev 2.0
- Two Common Public Radio Interface (CPRI) controller lanes
- High-speed USB 2.0 host and device controller with ULPI
interface
- Enhanced secure digital (SD/MMC) host controller (eSDHC)
- Antenna interface controller (AIC), supporting four industry standard JESD207/four custom ADI RF interfaces
- ADI lanes support both full duplex FDD support & half duplex TDD
- Universal Subscriber Identity Module (USIM) interface that facilitates communication to SIM cards or Eurochip pre-paid
phone
cards
- Two DUART, two eSPI, and two I2C controllers
- Integrated Flash memory controller (IFC)
- GPIO
- Sixteen 32-bit timers

Signed-off-by Naveen Burmi <[email protected] <javascript:;>>
Signed-off-by Poonam Aggrwal <[email protected] <javascript:;>
Quoted 1 line
Quoted 6 lines
Signed-off-by Prabhakar Kushwaha <[email protected] <javascript:;>>

---
Changes for v2: Incorporated Timur's review comments
- Removed SVR_9132_E as it is not required as part of following commit 48f6a5c348453fc3ab33aaa91e5e4198a28678ff

You didn't test after you did this, did you? This breaks the build.

arch/powerpc/cpu/mpc8xxx/cpu.c static struct cpu_type cpu_type_list[] = { · line 90

Quoted 12 lines
arch/powerpc/cpu/mpc8xxx/cpu.c +2 -0
index e8613be..03fd2fb 100644
@@ -86,6 +86,9 @@ static struct cpu_type cpu_type_list[] = {
        CPU_TYPE_ENTRY(B4220, B4220, 0),
        CPU_TYPE_ENTRY(BSC9130, 9130, 1),
        CPU_TYPE_ENTRY(BSC9131, 9131, 1),
+       CPU_TYPE_ENTRY(BSC9132, 9132, 2),
+       CPU_TYPE_ENTRY(BSC9132, 9132_E, 2),

You removed the declaration, but not the consumer. Please build-test before you submit.

Andy

Quoted 1 line
arch/powerpc/cpu/mpc8xxx/cpu.c +0 -0
 <http://lists.denx.de/mailman/listinfo/u-boot>
#2 lore raw

PATCH v2 1/1 powerpc/mpc85xx: Add BSC9132/BSC9232 processor support

Quoted 92 lines · Andy Fleming

On Monday, January 14, 2013, Prabhakar Kushwaha wrote:

The BSC9132 is a highly integrated device that targets the evolving Microcell, Picocell, and Enterprise-Femto base station market
subsegments.

The BSC9132 device combines Power Architecture e500 and DSP
StarCore SC3850
core technologies with MAPLE-B2P baseband acceleration processing
elements
to address the need for a high performance, low cost, integrated
solution
that handles all required processing layers without the need for an external device except for an RF transceiver or, in a Micro base
station
configuration, a host device that handles the L3/L4 and handover
between
sectors.

The BSC9132 SoC includes the following function and features:
- Power Architecture subsystem including two e500 processors with 512-Kbyte shared L2 cache
- Two StarCore SC3850 DSP subsystems, each with a 512-Kbyte
private L2
cache
- 32 Kbyte of shared M3 memory
- The Multi Accelerator Platform Engine for Pico BaseStation
Baseband
Processing (MAPLE-B2P)
- Two DDR3/3L memory interfaces with 32-bit data width (40
bits including
ECC), up to 1333 MHz data rate
- Dedicated security engine featuring trusted boot
- Two DMA controllers
- OCNDMA with four bidirectional channels
- SysDMA with sixteen bidirectional channels
- Interfaces
- Four-lane SerDes PHY
- PCI Express controller complies with the PEX
Specification-Rev 2.0
- Two Common Public Radio Interface (CPRI) controller lanes
- High-speed USB 2.0 host and device controller with
ULPI interface
- Enhanced secure digital (SD/MMC) host controller (eSDHC)
- Antenna interface controller (AIC), supporting four
industry
standard JESD207/four custom ADI RF interfaces
- ADI lanes support both full duplex FDD support & half
duplex TDD
- Universal Subscriber Identity Module (USIM) interface that facilitates communication to SIM cards or Eurochip
pre-paid phone
cards
- Two DUART, two eSPI, and two I2C controllers
- Integrated Flash memory controller (IFC)
- GPIO
- Sixteen 32-bit timers

Signed-off-by Naveen Burmi <[email protected] <javascript:;>>

<javascript:;>>

<javascript:;>>
---
Changes for v2: Incorporated Timur's review comments
- Removed SVR_9132_E as it is not required as part of following commit 48f6a5c348453fc3ab33aaa91e5e4198a28678ff

You didn't test after you did this, did you? This breaks the build.

    diff --git a/arch/powerpc/cpu/mpc8xxx/cpu.c
    b/arch/powerpc/cpu/mpc8xxx/cpu.c
    index e8613be..03fd2fb 100644
    --- a/arch/powerpc/cpu/mpc8xxx/cpu.c
    +++ b/arch/powerpc/cpu/mpc8xxx/cpu.c
    @@ -86,6 +86,9 @@ static struct cpu_type cpu_type_list[] = {
            CPU_TYPE_ENTRY(B4220, B4220, 0),
            CPU_TYPE_ENTRY(BSC9130, 9130, 1),
            CPU_TYPE_ENTRY(BSC9131, 9131, 1),
    +       CPU_TYPE_ENTRY(BSC9132, 9132, 2),
    +       CPU_TYPE_ENTRY(BSC9132, 9132_E, 2),
Quoted 3 lines

You removed the declaration, but not the consumer. Please build-test before you submit.

Sorry for this mistake.
I will take care this in near future.

Regards,
Prabhakar