0bda:819a RTL8188CUS WLAN doesn't work out of the box in downstream and upstreamkernel
Quoted 8 lines · Larry Finger
You are likely crashing more than X.
That is very good evidence that rtl8192cu is *NOT* the correct driver for that device. As I recall Xose found that USB ID in a Windows driver, but who knows what changes are inside that driver?
I have what I think is a complete collection of Realtek drivers for Linux, and none of them have 0bda:819a as a USB ID.
He's using the RTL8188C_8192C_USB_linux driver.
Therefore, there are only two possibilities:
- it's a 8192_du device, or
- it's a 8192_cu device, and there is a bug in rtlwifi.
Thomas, could you put "dmesg" output after loading 8192cu.ko (realtek driver) ? and "lsusb -v -d 0bda:819a" output.
A message that is not in the archive (sent off-list or not yet received): CAOAX8-k-Nbx4Om8fkEHRW2jmZCxKpsMY6oEZMAvdEQpXWn9Mdw@mail.gmail.com
Quoted 3 lines · Thomas Rosenkranz
btw. if I do:
$ sudo modprobe -r 8192cu the system crashes
That is a bug in the Realtek driver.
Larry
Quoted 5 lines · Thomas Rosenkranz
btw. if I do:
$ sudo modprobe -r 8192cu the system crashes[ 183.369324] rtw driver version=v3.4.4_xxxx.20120730
That release is a bit old. Try:
ftp://WebUser:[email protected]/cn/wlan/RTL8192xC_USB_linux_v3.4.4_4749.20121105.zip
A message that is not in the archive (sent off-list or not yet received): CAOAX8-kFtWuwEvz9v7hBzOwtohJx0NezrDHC0iVwXF29YYSCgQ@mail.gmail.com
your link didn't work, got driver from realtek homepage
tommy@Tommy-AIO:~$ modinfo 8192cu | egrep 'versi|filen|819' filename: /lib/modules/3.2.0-37-generic/kernel/drivers/net/wireless/8192cu.ko version: v3.4.4_4749.20121105 srcversion: 657E53E8FE213B566819C54
alias: usb:v0BDAp8191d*dc*dsc*dp*ic*isc*ip* vermagic: 3.2.0-37-generic SMP mod_unload modversions parm: rtw_chip_version:int
still the crash after trying to remove the modul
Quoted 16 lines
2013/2/5 Xose Vazquez Perez <[email protected]>
Quoted 12 lines · Thomas Rosenkranz
Quoted 6 lines
btw. if I do:
$ sudo modprobe -r 8192cu the system crashes[ 183.369324] rtw driver version=v3.4.4_xxxx.20120730That release is a bit old. Try:
ftp://WebUser:[email protected]/cn/wlan/RTL8192xC_USB_linux_v3.4.4_4749.20121105.zip
Quoted 11 lines · Thomas Rosenkranz
your link didn't work, got driver from realtek homepage
tommy@Tommy-AIO:~$ modinfo 8192cu | egrep 'versi|filen|819' filename: /lib/modules/3.2.0-37-generic/kernel/drivers/net/wireless/8192cu.ko version: v3.4.4_4749.20121105 srcversion: 657E53E8FE213B566819C54 alias: usb:v0BDAp8191d*dc*dsc*dp*ic*isc*ip* vermagic: 3.2.0-37-generic SMP mod_unload modversions parm: rtw_chip_version:intstill the crash after trying to removethe modul
Sorry, but I do not debug the vendor drivers.
Larry
A message that is not in the archive (sent off-list or not yet received): CAOAX8-mMsXu5h-7q2EJEc9SehWS=yqAb4YvbfOVBQKhdH+LqTQ@mail.gmail.com
---------- Forwarded message ----------
From: Thomas Rosenkranz <[email protected]>
Date: 2013/2/5
Subject: Re: FW: 0bda:819a RTL8188CUS WLAN doesn't work out of the box in downstream and upstreamkernel
To: linux-wireless <[email protected]>
Am 05.02.2013 00:00 schrieb "Thomas Rosenkranz" <[email protected]>:
Quoted 1,485 lines
btw. if I do:
$ sudo modprobe -r 8192cu the system crashesIn this case I did a kernel update and fresh installation of the realtek driver
here some output
Quoted 1,406 lines
tommy@Tommy-AIO:~$ modinfo 8192cu | egrep 'versi|filen|819' filename: /lib/modules/3.2.0-37-generic/kernel/drivers/net/wireless/8192cu.ko version: v3.4.4_xxxx.20120730 srcversion: FBF2DAF9D4C1BB74C28D37F alias: usb:v0BDAp8191d*dc*dsc*dp*ic*isc*ip* vermagic: 3.2.0-37-generic SMP mod_unload modversions parm: rtw_chip_version:inttommy@Tommy-AIO:~$ echo 'install 8192cu modprobe --ignore-install 8192cu ; /bin/echo "0bda 819a" > /sys/bus/usb/drivers/rtl8192cu/new_id' | sudo tee /etc/modprobe.d/8192cu.confinstall 8192cu modprobe --ignore-install 8192cu ;
/bin/echo"0bda 819a" >/sys/bus/usb/drivers/rtl8192cu/new_idtommy@Tommy-AIO:~$ sudo modprobe -v 8192cu install modprobe --ignore-install 8192cu ; /bin/echo "0bda 819a" > /sys/bus/usb/drivers/rtl8192cu/new_id insmod /lib/modules/3.2.0-37-generic/kernel/drivers/net/wireless/8192cu.kotommy@Tommy-AIO:~$ dmesg [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.2.0-37-generic (buildd@allspice) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #58-Ubuntu SMP Thu Jan 24 15:28:10 UTC 2013 (Ubuntu 3.2.0-37.58-generic 3.2.35) [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-37-generic root=UUID=ea1671bb-6d90-4e88-8808-5a5fc1bff71c ro nopat crashkernel=384M-2G:64M,2G-:128M resume=UUID=e4918e2d-1704-43a6-93c0-93235d39768e [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] Centaur CentaurHauls [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009d800 (usable) [ 0.000000] BIOS-e820: 000000000009d800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000de814000 (usable) [ 0.000000] BIOS-e820: 00000000de814000 - 00000000dee13000 (reserved) [ 0.000000] BIOS-e820: 00000000dee13000 - 00000000df093000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000df093000 - 00000000df098000 (ACPI data) [ 0.000000] BIOS-e820: 00000000df098000 - 00000000df0db000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000df0db000 - 00000000df4ba000 (usable) [ 0.000000] BIOS-e820: 00000000df4ba000 - 00000000df7f4000 (reserved) [ 0.000000] BIOS-e820: 00000000df7f4000 - 00000000df800000 (usable) [ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) [ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed04000 (reserved) [ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 000000021f000000 (usable) [ 0.000000] PAT support disabled. [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI 2.7 present. [ 0.000000] DMI: LENOVO Lenovo A720/ChiefRiver, BIOS E5KT20AUS 03/26/2012 [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable) [ 0.000000] No AGP bridge found [ 0.000000] last_pfn = 0x21f000 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-CFFFF write-protect [ 0.000000] D0000-E7FFF uncachable [ 0.000000] E8000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000 mask E00000000 write-back [ 0.000000] 1 base 200000000 mask FF0000000 write-back [ 0.000000] 2 base 210000000 mask FF8000000 write-back [ 0.000000] 3 base 218000000 mask FFC000000 write-back [ 0.000000] 4 base 21C000000 mask FFE000000 write-back [ 0.000000] 5 base 21E000000 mask FFF000000 write-back [ 0.000000] 6 base 0E0000000 mask FE0000000 uncachable [ 0.000000] 7 disabled [ 0.000000] 8 disabled [ 0.000000] 9 disabled [ 0.000000] original variable MTRRs [ 0.000000] reg 0, base: 0GB, range: 8GB, type WB [ 0.000000] reg 1, base: 8GB, range: 256MB, type WB [ 0.000000] reg 2, base: 8448MB, range: 128MB, type WB [ 0.000000] reg 3, base: 8576MB, range: 64MB, type WB [ 0.000000] reg 4, base: 8640MB, range: 32MB, type WB [ 0.000000] reg 5, base: 8672MB, range: 16MB, type WB [ 0.000000] reg 6, base: 3584MB, range: 512MB, type UC [ 0.000000] total RAM covered: 8176M [ 0.000000] Found optimal setting for mtrr clean up [ 0.000000] gran_size: 64K chunk_size: 32M num_reg: 6 lose cover RAM: 0G [ 0.000000] New variable MTRRs [ 0.000000] reg 0, base: 0GB, range: 2GB, type WB [ 0.000000] reg 1, base: 2GB, range: 1GB, type WB [ 0.000000] reg 2, base: 3GB, range: 512MB, type WB [ 0.000000] reg 3, base: 4GB, range: 4GB, type WB [ 0.000000] reg 4, base: 8GB, range: 512MB, type WB [ 0.000000] reg 5, base: 8688MB, range: 16MB, type UC [ 0.000000] e820 update range: 00000000e0000000 - 0000000100000000 (usable) ==> (reserved) [ 0.000000] last_pfn = 0xdf800 max_arch_pfn = 0x400000000 [ 0.000000] found SMP MP-table at [ffff8800000fcca0] fcca0 [ 0.000000] initial memory mapped : 0 - 20000000 [ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 20480 [ 0.000000] init_memory_mapping: 0000000000000000-00000000df800000 [ 0.000000] 0000000000 - 00df800000 page 2M [ 0.000000] kernel direct mapping tables up to df800000 @ 1fffb000-20000000 [ 0.000000] init_memory_mapping: 0000000100000000-000000021f000000 [ 0.000000] 0100000000 - 021f000000 page 2M [ 0.000000] kernel direct mapping tables up to 21f000000 @ df7fa000-df800000 [ 0.000000] RAMDISK: 358de000 - 36c67000 [ 0.000000] Reserving 128MB of memory at 720MB for crashkernel (System RAM: 8688MB) [ 0.000000] ACPI: RSDP 00000000000f0450 00024 (v02 LENOVO) [ 0.000000] ACPI: XSDT 00000000df047078 00074 (v01 LENOVO TC-03 00000120 AMI 00010013) [ 0.000000] ACPI: FACP 00000000df04ff10 000F4 (v04 LENOVO TC-03 00000120 AMI 00010013) [ 0.000000] ACPI: DSDT 00000000df047188 08D85 (v02 LENOVO TC-03 00000120 INTL 20051117) [ 0.000000] ACPI: FACS 00000000df091f80 00040 [ 0.000000] ACPI: APIC 00000000df050008 00092 (v03 LENOVO TC-03 00000120 AMI 00010013) [ 0.000000] ACPI: ASF! 00000000df0500a0 000A5 (v32 LENOVO TC-03 00000120 TFSM 000F4240) [ 0.000000] ACPI: MCFG 00000000df050148 0003C (v01 LENOVO TC-03 00000120 MSFT 00000097) [ 0.000000] ACPI: SLIC 00000000df050188 00176 (v01 LENOVO TC-03 00000120 AMI 00010013) [ 0.000000] ACPI: HPET 00000000df050300 00038 (v01 LENOVO TC-03 00000120 AMI. 00000005) [ 0.000000] ACPI: SSDT 00000000df050338 0036D (v01 LENOVO TC-03 00000120 INTL 20091112) [ 0.000000] ACPI: SSDT 00000000df0506a8 008E4 (v01 LENOVO TC-03 00000120 INTL 20051117) [ 0.000000] ACPI: SSDT 00000000df050f90 00A92 (v01 LENOVO TC-03 00000120 INTL 20051117) [ 0.000000] ACPI: SSDT 00000000df051a28 01392 (v01 LENOVO TC-03 00000120 INTL 20091112) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at 0000000000000000-000000021f000000 [ 0.000000] Initmem setup node 0 0000000000000000-000000021f000000 [ 0.000000] NODE_DATA [000000021effb000 - 000000021effffff] [ 0.000000] [ffffea0000000000-ffffea00087fffff] PMD -> [ffff880216600000-ffff88021e5fffff] on node 0 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal 0x00100000 -> 0x0021f000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[5] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009d [ 0.000000] 0: 0x00000100 -> 0x000de814 [ 0.000000] 0: 0x000df0db -> 0x000df4ba [ 0.000000] 0: 0x000df7f4 -> 0x000df800 [ 0.000000] 0: 0x00100000 -> 0x0021f000 [ 0.000000] On node 0 totalpages: 2087820 [ 0.000000] DMA zone: 64 pages used for memmap [ 0.000000] DMA zone: 5 pages reserved [ 0.000000] DMA zone: 3912 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 16320 pages used for memmap [ 0.000000] DMA32 zone: 891967 pages, LIFO batch:31 [ 0.000000] Normal zone: 18368 pages used for memmap [ 0.000000] Normal zone: 1157184 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x03] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x05] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000 [ 0.000000] SMP: Allowing 8 CPUs, 0 hotplug CPUs [ 0.000000] nr_irqs_gsi: 40 [ 0.000000] PM: Registered nosave memory: 000000000009d000 - 000000000009e000 [ 0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 [ 0.000000] PM: Registered nosave memory: 00000000de814000 - 00000000dee13000 [ 0.000000] PM: Registered nosave memory: 00000000dee13000 - 00000000df093000 [ 0.000000] PM: Registered nosave memory: 00000000df093000 - 00000000df098000 [ 0.000000] PM: Registered nosave memory: 00000000df098000 - 00000000df0db000 [ 0.000000] PM: Registered nosave memory: 00000000df4ba000 - 00000000df7f4000 [ 0.000000] PM: Registered nosave memory: 00000000df800000 - 00000000f8000000 [ 0.000000] PM: Registered nosave memory: 00000000f8000000 - 00000000fc000000 [ 0.000000] PM: Registered nosave memory: 00000000fc000000 - 00000000fec00000 [ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000 [ 0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fed00000 [ 0.000000] PM: Registered nosave memory: 00000000fed00000 - 00000000fed04000 [ 0.000000] PM: Registered nosave memory: 00000000fed04000 - 00000000fed1c000 [ 0.000000] PM: Registered nosave memory: 00000000fed1c000 - 00000000fed20000 [ 0.000000] PM: Registered nosave memory: 00000000fed20000 - 00000000fee00000 [ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000 [ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ff000000 [ 0.000000] PM: Registered nosave memory: 00000000ff000000 - 0000000100000000 [ 0.000000] Allocating PCI resources starting at df800000 (gap: df800000:18800000) [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:8 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88021ec00000 s83136 r8192 d23360 u262144 [ 0.000000] pcpu-alloc: s83136 r8192 d23360 u262144 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2053063 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-37-generic root=UUID=ea1671bb-6d90-4e88-8808-5a5fc1bff71c ro nopat crashkernel=384M-2G:64M,2G-:128M resume=UUID=e4918e2d-1704-43a6-93c0-93235d39768e [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340 [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing! [ 0.000000] Memory: 7986328k/8896512k available (6569k kernel code, 545232k absent, 364952k reserved, 6634k data, 924k init) [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000] NR_IRQS:16640 nr_irqs:744 16 [ 0.000000] Extended CMOS year: 2000 [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] allocated 67108864 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] hpet clockevent registered [ 0.000000] Fast TSC calibration using PIT [ 0.004000] Detected 2294.705 MHz processor. [ 0.000002] Calibrating delay loop (skipped), value calculated using timer frequency.. 4589.41 BogoMIPS (lpj=9178820) [ 0.000165] pid_max: default: 32768 minimum: 301 [ 0.000263] Security Framework initialized [ 0.000351] AppArmor: AppArmor initialized [ 0.000428] Yama: becoming mindful. [ 0.001026] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.003216] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.004225] Mount-cache hash table entries: 256 [ 0.004396] Initializing cgroup subsys cpuacct [ 0.004478] Initializing cgroup subsys memory [ 0.004561] Initializing cgroup subsys devices [ 0.004641] Initializing cgroup subsys freezer [ 0.004719] Initializing cgroup subsys blkio [ 0.004799] Initializing cgroup subsys perf_event [ 0.004915] CPU: Physical Processor ID: 0 [ 0.004991] CPU: Processor Core ID: 0 [ 0.005072] ENERGY_PERF_BIAS: Set to 'normal', was 'performance' [ 0.005073] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8) [ 0.005622] mce: CPU supports 9 MCE banks [ 0.005713] CPU0: Thermal monitoring enabled (TM1) [ 0.005799] using mwait in idle threads. [ 0.007913] ACPI: Core revision 20110623 [ 0.013690] ftrace: allocating 27033 entries in 107 pages [ 0.022699] x2apic not enabled, IRQ remapping init failed [ 0.023186] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.062930] CPU0: Intel(R) Core(TM) i7-3610QM CPU @ 2.30GHz stepping 09 [ 0.168769] Performance Events: PEBS fmt1+, generic architected perfmon, Intel PMU driver. [ 0.169021] ... version: 3 [ 0.169095] ... bit width: 48 [ 0.169169] ... generic registers: 4 [ 0.169247] ... value mask: 0000ffffffffffff [ 0.169329] ... max period: 000000007fffffff [ 0.169406] ... fixed-purpose events: 3 [ 0.169483] ... event mask: 000000070000000f [ 0.169693] NMI watchdog enabled, takes one hw-pmu counter. [ 0.169841] Booting Node 0, Processors #1 [ 0.169947] smpboot cpu 1: start_ip = 98000 [ 0.281218] NMI watchdog enabled, takes one hw-pmu counter. [ 0.281371] #2 [ 0.281425] smpboot cpu 2: start_ip = 98000 [ 0.389117] NMI watchdog enabled, takes one hw-pmu counter. [ 0.389265] #3 [ 0.389316] smpboot cpu 3: start_ip = 98000 [ 0.497104] NMI watchdog enabled, takes one hw-pmu counter. [ 0.497254] #4 [ 0.497305] smpboot cpu 4: start_ip = 98000 [ 0.604999] NMI watchdog enabled, takes one hw-pmu counter. [ 0.605164] #5 [ 0.605214] smpboot cpu 5: start_ip = 98000 [ 0.720910] NMI watchdog enabled, takes one hw-pmu counter. [ 0.721061] #6 [ 0.721112] smpboot cpu 6: start_ip = 98000 [ 0.828901] NMI watchdog enabled, takes one hw-pmu counter. [ 0.829051] #7 Ok. [ 0.829123] smpboot cpu 7: start_ip = 98000 [ 0.936847] NMI watchdog enabled, takes one hw-pmu counter. [ 0.936955] Brought up 8 CPUs [ 0.937030] Total of 8 processors activated (36715.02 BogoMIPS). [ 0.945300] devtmpfs: initialized [ 0.946151] EVM: security.selinux [ 0.946227] EVM: security.SMACK64 [ 0.946302] EVM: security.capability [ 0.946395] PM: Registering ACPI NVS region at dee13000 (2621440 bytes) [ 0.946512] PM: Registering ACPI NVS region at df098000 (274432 bytes) [ 0.947316] print_constraints: dummy: [ 0.947421] RTC time: 23:42:55, date: 02/04/13 [ 0.947525] NET: Registered protocol family 16 [ 0.947687] Trying to unpack rootfs image as initramfs... [ 0.947691] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 0.947693] ACPI: bus type pci registered [ 0.947752] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000) [ 0.947755] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820 [ 0.954195] PCI: Using configuration type 1 for base access [ 0.955073] bio: create slab <bio-0> at 0 [ 0.955214] ACPI: Added _OSI(Module Device) [ 0.955292] ACPI: Added _OSI(Processor Device) [ 0.955370] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.955451] ACPI: Added _OSI(Processor Aggregator Device) [ 0.956930] ACPI: EC: Look up EC in DSDT [ 0.958266] ACPI: Executed 1 blocks of module-level executable AML code [ 1.025234] ACPI: SSDT 00000000dedbf018 0083B (v01 PmRef Cpu0Cst 00003001 INTL 20051117) [ 1.025787] ACPI: Dynamic OEM Table Load: [ 1.025958] ACPI: SSDT (null) 0083B (v01 PmRef Cpu0Cst 00003001 INTL 20051117) [ 1.052476] ACPI: SSDT 00000000dedc0a98 00303 (v01 PmRef ApIst 00003000 INTL 20051117) [ 1.053055] ACPI: Dynamic OEM Table Load: [ 1.053227] ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000 INTL 20051117) [ 1.076341] ACPI: SSDT 00000000dedc2c18 00119 (v01 PmRef ApCst 00003000 INTL 20051117) [ 1.076888] ACPI: Dynamic OEM Table Load: [ 1.077058] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20051117) [ 1.101281] ACPI: Interpreter enabled [ 1.101361] ACPI: (supports S0 S3 S4 S5) [ 1.101642] ACPI: Using IOAPIC for interrupt routing [ 1.106718] ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62 [ 1.106969] ACPI: No dock devices found. [ 1.107046] HEST: Table not found. [ 1.107124] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 1.107511] \_SB_.PCI0:_OSC invalid UUID [ 1.107512] _OSC request data:1 8 1f [ 1.107516] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e]) [ 1.108026] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7] [ 1.108110] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff] [ 1.108195] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] [ 1.108304] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000d3fff] [ 1.108410] pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff] [ 1.108517] pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff] [ 1.108622] pci_root PNP0A08:00: host bridge window [mem 0x000dc000-0x000dffff] [ 1.108729] pci_root PNP0A08:00: host bridge window [mem 0x000e0000-0x000e3fff] [ 1.108833] pci_root PNP0A08:00: host bridge window [mem 0x000e4000-0x000e7fff] [ 1.108940] pci_root PNP0A08:00: host bridge window [mem 0xe0000000-0xfeafffff] [ 1.109055] pci 0000:00:00.0: [8086:0154] type 0 class 0x000600 [ 1.109092] pci 0000:00:01.0: [8086:0151] type 1 class 0x000604 [ 1.109123] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold [ 1.109126] pci 0000:00:01.0: PME# disabled [ 1.109167] pci 0000:00:14.0: [8086:1e31] type 0 class 0x000c03 [ 1.109191] pci 0000:00:14.0: reg 10: [mem 0xf7d00000-0xf7d0ffff 64bit] [ 1.109264] pci 0000:00:14.0: PME# supported from D3hot D3cold [ 1.109268] pci 0000:00:14.0: PME# disabled [ 1.109291] pci 0000:00:16.0: [8086:1e3a] type 0 class 0x000780 [ 1.109315] pci 0000:00:16.0: reg 10: [mem 0xf7d1a000-0xf7d1a00f 64bit] [ 1.109394] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold [ 1.109398] pci 0000:00:16.0: PME# disabled [ 1.109430] pci 0000:00:1a.0: [8086:1e2d] type 0 class 0x000c03 [ 1.109452] pci 0000:00:1a.0: reg 10: [mem 0xf7d18000-0xf7d183ff] [ 1.109544] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold [ 1.109549] pci 0000:00:1a.0: PME# disabled [ 1.109575] pci 0000:00:1b.0: [8086:1e20] type 0 class 0x000403 [ 1.109590] pci 0000:00:1b.0: reg 10: [mem 0xf7d10000-0xf7d13fff 64bit] [ 1.109661] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold [ 1.109665] pci 0000:00:1b.0: PME# disabled [ 1.109688] pci 0000:00:1c.0: [8086:1e10] type 1 class 0x000604 [ 1.109769] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 1.109774] pci 0000:00:1c.0: PME# disabled [ 1.109798] pci 0000:00:1c.1: [8086:1e12] type 1 class 0x000604 [ 1.109879] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold [ 1.109883] pci 0000:00:1c.1: PME# disabled [ 1.109909] pci 0000:00:1c.2: [8086:1e14] type 1 class 0x000604 [ 1.109989] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold [ 1.109993] pci 0000:00:1c.2: PME# disabled [ 1.110027] pci 0000:00:1d.0: [8086:1e26] type 0 class 0x000c03 [ 1.110049] pci 0000:00:1d.0: reg 10: [mem 0xf7d17000-0xf7d173ff] [ 1.110141] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold [ 1.110146] pci 0000:00:1d.0: PME# disabled [ 1.110170] pci 0000:00:1f.0: [8086:1e59] type 0 class 0x000601 [ 1.110296] pci 0000:00:1f.2: [8086:1e03] type 0 class 0x000106 [ 1.110315] pci 0000:00:1f.2: reg 10: [io 0xf070-0xf077] [ 1.110324] pci 0000:00:1f.2: reg 14: [io 0xf060-0xf063] [ 1.110332] pci 0000:00:1f.2: reg 18: [io 0xf050-0xf057] [ 1.110341] pci 0000:00:1f.2: reg 1c: [io 0xf040-0xf043] [ 1.110349] pci 0000:00:1f.2: reg 20: [io 0xf020-0xf03f] [ 1.110358] pci 0000:00:1f.2: reg 24: [mem 0xf7d16000-0xf7d167ff] [ 1.110405] pci 0000:00:1f.2: PME# supported from D3hot [ 1.110409] pci 0000:00:1f.2: PME# disabled [ 1.110427] pci 0000:00:1f.3: [8086:1e22] type 0 class 0x000c05 [ 1.110443] pci 0000:00:1f.3: reg 10: [mem 0xf7d15000-0xf7d150ff 64bit] [ 1.110465] pci 0000:00:1f.3: reg 20: [io 0xf000-0xf01f] [ 1.110525] pci 0000:01:00.0: [10de:0de9] type 0 class 0x000300 [ 1.110535] pci 0000:01:00.0: reg 10: [mem 0xf6000000-0xf6ffffff] [ 1.110546] pci 0000:01:00.0: reg 14: [mem 0xe0000000-0xefffffff 64bit pref] [ 1.110557] pci 0000:01:00.0: reg 1c: [mem 0xf0000000-0xf1ffffff 64bit pref] [ 1.110565] pci 0000:01:00.0: reg 24: [io 0xe000-0xe07f] [ 1.110572] pci 0000:01:00.0: reg 30: [mem 0xf7000000-0xf707ffff pref] [ 1.110629] pci 0000:01:00.1: [10de:0bea] type 0 class 0x000403 [ 1.110639] pci 0000:01:00.1: reg 10: [mem 0xf7080000-0xf7083fff] [ 1.116247] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 1.116330] pci 0000:00:01.0: bridge window [io 0xe000-0xefff] [ 1.116333] pci 0000:00:01.0: bridge window [mem 0xf6000000-0xf70fffff] [ 1.116336] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xf1ffffff 64bit pref] [ 1.116408] pci 0000:02:00.0: [1131:7231] type 0 class 0x000480 [ 1.116448] pci 0000:02:00.0: reg 10: [mem 0xf7800000-0xf7bfffff 64bit] [ 1.116479] pci 0000:02:00.0: reg 18: [mem 0xf7400000-0xf77fffff 64bit] [ 1.116646] pci 0000:02:00.0: supports D1 D2 [ 1.116648] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot [ 1.116654] pci 0000:02:00.0: PME# disabled [ 1.124247] pci 0000:00:1c.0: PCI bridge to [bus 02-02] [ 1.124334] pci 0000:00:1c.0: bridge window [mem 0xf7400000-0xf7bfffff] [ 1.124408] pci 0000:03:00.0: [10ec:8168] type 0 class 0x000200 [ 1.124429] pci 0000:03:00.0: reg 10: [io 0xd000-0xd0ff] [ 1.124464] pci 0000:03:00.0: reg 18: [mem 0xf2104000-0xf2104fff 64bit pref] [ 1.124487] pci 0000:03:00.0: reg 20: [mem 0xf2100000-0xf2103fff 64bit pref] [ 1.124581] pci 0000:03:00.0: supports D1 D2 [ 1.124583] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.124589] pci 0000:03:00.0: PME# disabled [ 1.132241] pci 0000:00:1c.1: PCI bridge to [bus 03-03] [ 1.132326] pci 0000:00:1c.1: bridge window [io 0xd000-0xdfff] [ 1.132334] pci 0000:00:1c.1: bridge window [mem 0xf2100000-0xf21fffff 64bit pref] [ 1.132458] pci 0000:04:00.0: [10ec:5229] type 0 class 0x00ff00 [ 1.132525] pci 0000:04:00.0: reg 10: [mem 0xf7c00000-0xf7c00fff] [ 1.133017] pci 0000:04:00.0: supports D1 D2 [ 1.133019] pci 0000:04:00.0: PME# supported from D1 D2 D3hot [ 1.133030] pci 0000:04:00.0: PME# disabled [ 1.140261] pci 0000:00:1c.2: PCI bridge to [bus 04-04] [ 1.140346] pci 0000:00:1c.2: bridge window [mem 0xf7c00000-0xf7cfffff] [ 1.140371] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 1.140478] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] [ 1.140507] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT] [ 1.140542] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG0._PRT] [ 1.140577] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] [ 1.140663] \_SB_.PCI0:_OSC invalid UUID [ 1.140664] _OSC request data:1 1f 1f [ 1.140668] pci0000:00: Requesting ACPI _OSC control (0x1d) [ 1.140787] \_SB_.PCI0:_OSC invalid UUID [ 1.140788] _OSC request data:1 0 1d [ 1.140791] pci0000:00: ACPI _OSC request failed (AE_ERROR), returned control mask: 0x1d [ 1.140898] ACPI _OSC control for PCIe not granted, disabling ASPM [ 1.144339] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15) [ 1.144976] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *10 11 12 14 15) [ 1.145610] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 6 10 11 12 14 15) [ 1.146249] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 10 11 12 14 15) [ 1.146880] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled. [ 1.147623] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled. [ 1.148374] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 10 11 12 14 15) [ 1.149008] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 *11 12 14 15) [ 1.149694] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none [ 1.149804] vgaarb: loaded [ 1.149878] vgaarb: bridge control possible 0000:01:00.0 [ 1.150037] i2c-core: driver [aat2870] using legacy suspend method [ 1.150121] i2c-core: driver [aat2870] using legacy resume method [ 1.150254] SCSI subsystem initialized [ 1.150358] libata version 3.00 loaded. [ 1.150393] usbcore: registered new interface driver usbfs [ 1.150481] usbcore: registered new interface driver hub [ 1.150578] usbcore: registered new device driver usb [ 1.150719] PCI: Using ACPI for IRQ routing [ 1.152326] PCI: pci_cache_line_size set to 64 bytes [ 1.152415] reserve RAM buffer: 000000000009d800 - 000000000009ffff [ 1.152417] reserve RAM buffer: 00000000de814000 - 00000000dfffffff [ 1.152420] reserve RAM buffer: 00000000df4ba000 - 00000000dfffffff [ 1.152422] reserve RAM buffer: 00000000df800000 - 00000000dfffffff [ 1.152423] reserve RAM buffer: 000000021f000000 - 000000021fffffff [ 1.152503] NetLabel: Initializing [ 1.152576] NetLabel: domain hash size = 128 [ 1.152652] NetLabel: protocols = UNLABELED CIPSOv4 [ 1.152742] NetLabel: unlabeled traffic allowed by default [ 1.152859] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0 [ 1.153363] hpet0: 8 comparators, 64-bit 14.318180 MHz counter [ 1.155456] Switching to clocksource hpet [ 1.160455] AppArmor: AppArmor Filesystem Enabled [ 1.160550] pnp: PnP ACPI init [ 1.160632] ACPI: bus type pnp registered [ 1.160923] pnp 00:00: [bus 00-3e] [ 1.160925] pnp 00:00: [io 0x0000-0x0cf7 window] [ 1.160927] pnp 00:00: [io 0x0cf8-0x0cff] [ 1.160929] pnp 00:00: [io 0x0d00-0xffff window] [ 1.160931] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 1.160933] pnp 00:00: [mem 0x000c0000-0x000c3fff window] [ 1.160934] pnp 00:00: [mem 0x000c4000-0x000c7fff window] [ 1.160936] pnp 00:00: [mem 0x000c8000-0x000cbfff window] [ 1.160938] pnp 00:00: [mem 0x000cc000-0x000cffff window] [ 1.160939] pnp 00:00: [mem 0x000d0000-0x000d3fff window] [ 1.160941] pnp 00:00: [mem 0x000d4000-0x000d7fff window] [ 1.160943] pnp 00:00: [mem 0x000d8000-0x000dbfff window] [ 1.160944] pnp 00:00: [mem 0x000dc000-0x000dffff window] [ 1.160946] pnp 00:00: [mem 0x000e0000-0x000e3fff window] [ 1.160948] pnp 00:00: [mem 0x000e4000-0x000e7fff window] [ 1.160949] pnp 00:00: [mem 0x000e8000-0x000ebfff window] [ 1.160951] pnp 00:00: [mem 0x000ec000-0x000effff window] [ 1.160953] pnp 00:00: [mem 0x000f0000-0x000fffff window] [ 1.160956] pnp 00:00: [mem 0xe0000000-0xfeafffff window] [ 1.160958] pnp 00:00: [mem 0x00010000-0x0001ffff window] [ 1.161010] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) [ 1.161030] pnp 00:01: [mem 0xfed40000-0xfed44fff] [ 1.161061] system 00:01: [mem 0xfed40000-0xfed44fff] has been reserved [ 1.161143] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active) [ 1.161153] pnp 00:02: [io 0x0000-0x001f] [ 1.161154] pnp 00:02: [io 0x0081-0x0091] [ 1.161156] pnp 00:02: [io 0x0093-0x009f] [ 1.161157] pnp 00:02: [io 0x00c0-0x00df] [ 1.161159] pnp 00:02: [dma 4] [ 1.161177] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active) [ 1.161183] pnp 00:03: [mem 0xff000000-0xffffffff] [ 1.161199] pnp 00:03: Plug and Play ACPI device, IDs INT0800 (active) [ 1.161263] pnp 00:04: [mem 0xfed00000-0xfed003ff] [ 1.161280] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active) [ 1.161290] pnp 00:05: [io 0x002e-0x002f] [ 1.161291] pnp 00:05: [io 0x004e-0x004f] [ 1.161293] pnp 00:05: [io 0x0061] [ 1.161294] pnp 00:05: [io 0x0063] [ 1.161295] pnp 00:05: [io 0x0065] [ 1.161297] pnp 00:05: [io 0x0067] [ 1.161298] pnp 00:05: [io 0x0070] [ 1.161299] pnp 00:05: [io 0x0080] [ 1.161301] pnp 00:05: [io 0x0092] [ 1.161302] pnp 00:05: [io 0x00b2-0x00b3] [ 1.161303] pnp 00:05: [io 0x0680-0x069f] [ 1.161305] pnp 00:05: [io 0x0200-0x020f] [ 1.161306] pnp 00:05: [io 0xffff] [ 1.161308] pnp 00:05: [io 0xffff] [ 1.161309] pnp 00:05: [io 0x0400-0x0453] [ 1.161310] pnp 00:05: [io 0x0458-0x047f] [ 1.161312] pnp 00:05: [io 0x0500-0x057f] [ 1.161313] pnp 00:05: [io 0x164e-0x164f] [ 1.161346] system 00:05: [io 0x0680-0x069f] has been reserved [ 1.161429] system 00:05: [io 0x0200-0x020f] has been reserved [ 1.161512] system 00:05: [io 0xffff] has been reserved [ 1.161593] system 00:05: [io 0xffff] has been reserved [ 1.161675] system 00:05: [io 0x0400-0x0453] has been reserved [ 1.161758] system 00:05: [io 0x0458-0x047f] has been reserved [ 1.161841] system 00:05: [io 0x0500-0x057f] has been reserved [ 1.161924] system 00:05: [io 0x164e-0x164f] has been reserved [ 1.162008] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.162015] pnp 00:06: [io 0x0070-0x0077] [ 1.162023] pnp 00:06: [irq 8] [ 1.162042] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active) [ 1.162063] pnp 00:07: [io 0x0454-0x0457] [ 1.162092] system 00:07: [io 0x0454-0x0457] has been reserved [ 1.162176] system 00:07: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active) [ 1.162193] pnp 00:08: [io 0x0010-0x001f] [ 1.162195] pnp 00:08: [io 0x0022-0x003f] [ 1.162196] pnp 00:08: [io 0x0044-0x005f] [ 1.162198] pnp 00:08: [io 0x0072-0x007f] [ 1.162199] pnp 00:08: [io 0x0080] [ 1.162201] pnp 00:08: [io 0x0084-0x0086] [ 1.162202] pnp 00:08: [io 0x0088] [ 1.162203] pnp 00:08: [io 0x008c-0x008e] [ 1.162205] pnp 00:08: [io 0x0090-0x009f] [ 1.162206] pnp 00:08: [io 0x00a2-0x00bf] [ 1.162208] pnp 00:08: [io 0x00e0-0x00ef] [ 1.162210] pnp 00:08: [io 0x04d0-0x04d1] [ 1.162240] system 00:08: [io 0x04d0-0x04d1] has been reserved [ 1.162322] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.162329] pnp 00:09: [io 0x00f0-0x00ff] [ 1.162334] pnp 00:09: [irq 13] [ 1.162353] pnp 00:09: Plug and Play ACPI device, IDs PNP0c04 (active) [ 1.162543] pnp 00:0a: [mem 0xfed1c000-0xfed1ffff] [ 1.162545] pnp 00:0a: [mem 0xfed10000-0xfed17fff] [ 1.162546] pnp 00:0a: [mem 0xfed18000-0xfed18fff] [ 1.162548] pnp 00:0a: [mem 0xfed19000-0xfed19fff] [ 1.162549] pnp 00:0a: [mem 0xf8000000-0xfbffffff] [ 1.162551] pnp 00:0a: [mem 0xfed20000-0xfed3ffff] [ 1.162552] pnp 00:0a: [mem 0xfed90000-0xfed93fff] [ 1.162554] pnp 00:0a: [mem 0xfed45000-0xfed8ffff] [ 1.162555] pnp 00:0a: [mem 0xff000000-0xffffffff] [ 1.162557] pnp 00:0a: [mem 0xfee00000-0xfeefffff] [ 1.162558] pnp 00:0a: [mem 0xf2200000-0xf2200fff] [ 1.162609] system 00:0a: [mem 0xfed1c000-0xfed1ffff] has been reserved [ 1.162695] system 00:0a: [mem 0xfed10000-0xfed17fff] has been reserved [ 1.162780] system 00:0a: [mem 0xfed18000-0xfed18fff] has been reserved [ 1.162863] system 00:0a: [mem 0xfed19000-0xfed19fff] has been reserved [ 1.162947] system 00:0a: [mem 0xf8000000-0xfbffffff] has been reserved [ 1.163032] system 00:0a: [mem 0xfed20000-0xfed3ffff] has been reserved [ 1.163117] system 00:0a: [mem 0xfed90000-0xfed93fff] has been reserved [ 1.163199] system 00:0a: [mem 0xfed45000-0xfed8ffff] has been reserved [ 1.163285] system 00:0a: [mem 0xff000000-0xffffffff] has been reserved [ 1.163369] system 00:0a: [mem 0xfee00000-0xfeefffff] could not be reserved [ 1.163453] system 00:0a: [mem 0xf2200000-0xf2200fff] has been reserved [ 1.163548] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.163664] pnp: PnP ACPI: found 11 devices [ 1.163743] ACPI: ACPI bus type pnp unregistered [ 1.170051] PCI: max bus depth: 1 pci_try_num: 2 [ 1.170081] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 1.170164] pci 0000:00:01.0: bridge window [io 0xe000-0xefff] [ 1.170249] pci 0000:00:01.0: bridge window [mem 0xf6000000-0xf70fffff] [ 1.170334] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xf1ffffff 64bit pref] [ 1.170442] pci 0000:00:1c.0: PCI bridge to [bus 02-02] [ 1.170525] pci 0000:00:1c.0: bridge window [mem 0xf7400000-0xf7bfffff] [ 1.170616] pci 0000:00:1c.1: PCI bridge to [bus 03-03] [ 1.170697] pci 0000:00:1c.1: bridge window [io 0xd000-0xdfff] [ 1.170787] pci 0000:00:1c.1: bridge window [mem 0xf2100000-0xf21fffff 64bit pref] [ 1.170897] pci 0000:00:1c.2: PCI bridge to [bus 04-04] [ 1.170982] pci 0000:00:1c.2: bridge window [mem 0xf7c00000-0xf7cfffff] [ 1.171082] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.171168] pci 0000:00:01.0: setting latency timer to 64 [ 1.171175] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.171262] pci 0000:00:1c.0: setting latency timer to 64 [ 1.171272] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 1.171360] pci 0000:00:1c.1: setting latency timer to 64 [ 1.171368] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 1.171456] pci 0000:00:1c.2: setting latency timer to 64 [ 1.171460] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 1.171462] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 1.171464] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 1.171466] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff] [ 1.171468] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff] [ 1.171469] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff] [ 1.171471] pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff] [ 1.171473] pci_bus 0000:00: resource 11 [mem 0x000e0000-0x000e3fff] [ 1.171475] pci_bus 0000:00: resource 12 [mem 0x000e4000-0x000e7fff] [ 1.171477] pci_bus 0000:00: resource 13 [mem 0xe0000000-0xfeafffff] [ 1.171479] pci_bus 0000:01: resource 0 [io 0xe000-0xefff] [ 1.171480] pci_bus 0000:01: resource 1 [mem 0xf6000000-0xf70fffff] [ 1.171482] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xf1ffffff 64bit pref] [ 1.171485] pci_bus 0000:02: resource 1 [mem 0xf7400000-0xf7bfffff] [ 1.171486] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff] [ 1.171488] pci_bus 0000:03: resource 2 [mem 0xf2100000-0xf21fffff 64bit pref] [ 1.171490] pci_bus 0000:04: resource 1 [mem 0xf7c00000-0xf7cfffff] [ 1.171517] NET: Registered protocol family 2 [ 1.171757] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 1.172505] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 1.173635] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 1.173834] TCP: Hash tables configured (established 524288 bind 65536) [ 1.173918] TCP reno registered [ 1.174005] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 1.174115] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 1.174271] NET: Registered protocol family 1 [ 1.174368] pci 0000:00:14.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.176759] pci 0000:00:14.0: PCI INT A disabled [ 1.176850] pci 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.195532] pci 0000:00:1a.0: PCI INT A disabled [ 1.195635] pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 1.215518] pci 0000:00:1d.0: PCI INT A disabled [ 1.215619] pci 0000:01:00.0: Boot video device [ 1.215644] PCI: CLS 64 bytes, default 64 [ 1.215646] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 1.215731] Placing 64MB software IO TLB between ffff8800da814000 - ffff8800de814000 [ 1.215839] software IO TLB at phys 0xda814000 - 0xde814000 [ 1.216458] audit: initializing netlink socket (disabled) [ 1.216546] type=2000 audit(1360021374.988:1): initialized [ 1.239450] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 1.241242] VFS: Disk quotas dquot_6.5.2 [ 1.241358] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.241813] fuse init (API version 7.17) [ 1.241957] msgmni has been set to 15598 [ 1.247432] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 1.247570] io scheduler noop registered [ 1.247649] io scheduler deadline registered [ 1.247752] io scheduler cfq registered (default) [ 1.247897] pcieport 0000:00:01.0: setting latency timer to 64 [ 1.247920] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X [ 1.248096] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 1.248193] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 1.248315] intel_idle: MWAIT substates: 0x21120 [ 1.248317] intel_idle: v0.4 model 0x3A [ 1.248318] intel_idle: lapic_timer_reliable_states 0xffffffff [ 1.248411] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0 [ 1.248522] ACPI: Power Button [PWRB] [ 1.248629] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 1.248737] ACPI: Power Button [PWRF] [ 1.250745] thermal LNXTHERM:00: registered as thermal_zone0 [ 1.250829] ACPI: Thermal Zone [TZ00] (47 C) [ 1.252228] thermal LNXTHERM:01: registered as thermal_zone1 [ 1.252311] ACPI: Thermal Zone [TZ01] (47 C) [ 1.252423] ERST: Table is not found! [ 1.252500] GHES: HEST is not enabled! [ 1.252629] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 1.286853] Freeing initrd memory: 20004k freed [ 1.463851] Linux agpgart interface v0.103 [ 1.465049] brd: module loaded [ 1.465671] loop: module loaded [ 1.465837] ahci 0000:00:1f.2: version 3.0 [ 1.465855] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 1.465987] ahci 0000:00:1f.2: irq 41 for MSI/MSI-X [ 1.479415] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x7 impl SATA mode [ 1.479524] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems apst [ 1.479634] ahci 0000:00:1f.2: setting latency timer to 64 [ 1.495756] scsi0 : ahci [ 1.495898] scsi1 : ahci [ 1.496026] scsi2 : ahci [ 1.496154] scsi3 : ahci [ 1.496282] scsi4 : ahci [ 1.496409] scsi5 : ahci [ 1.496734] ata1: SATA max UDMA/133 abar m2048@0xf7d16000 port 0xf7d16100 irq 41 [ 1.496840] ata2: SATA max UDMA/133 abar m2048@0xf7d16000 port 0xf7d16180 irq 41 [ 1.496948] ata3: SATA max UDMA/133 abar m2048@0xf7d16000 port 0xf7d16200 irq 41 [ 1.497054] ata4: DUMMY [ 1.497127] ata5: DUMMY [ 1.497200] ata6: DUMMY [ 1.497530] Fixed MDIO Bus: probed [ 1.497619] tun: Universal TUN/TAP device driver, 1.6 [ 1.497700] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 1.497818] PPP generic driver version 2.4.2 [ 1.497968] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.498065] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.498163] ehci_hcd 0000:00:1a.0: setting latency timer to 64 [ 1.498167] ehci_hcd 0000:00:1a.0: EHCI Host Controller [ 1.498281] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 [ 1.498412] ehci_hcd 0000:00:1a.0: debug port 2 [ 1.502387] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported [ 1.502401] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xf7d18000 [ 1.515368] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00 [ 1.515557] hub 1-0:1.0: USB hub found [ 1.515637] hub 1-0:1.0: 2 ports detected [ 1.515762] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 1.515859] ehci_hcd 0000:00:1d.0: setting latency timer to 64 [ 1.515863] ehci_hcd 0000:00:1d.0: EHCI Host Controller [ 1.515977] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 1.516102] ehci_hcd 0000:00:1d.0: debug port 2 [ 1.520076] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported [ 1.520089] ehci_hcd 0000:00:1d.0: irq 23, io mem 0xf7d17000 [ 1.535358] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00 [ 1.535536] hub 2-0:1.0: USB hub found [ 1.535614] hub 2-0:1.0: 2 ports detected [ 1.535735] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.535826] uhci_hcd: USB Universal Host Controller Interface driver [ 1.535931] xhci_hcd 0000:00:14.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.536035] xhci_hcd 0000:00:14.0: setting latency timer to 64 [ 1.536039] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 1.536155] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3 [ 1.536344] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported [ 1.536348] xhci_hcd 0000:00:14.0: irq 16, io mem 0xf7d00000 [ 1.536470] xhci_hcd 0000:00:14.0: irq 42 for MSI/MSI-X [ 1.536562] xHCI xhci_add_endpoint called for root hub [ 1.536563] xHCI xhci_check_bandwidth called for root hub [ 1.536582] hub 3-0:1.0: USB hub found [ 1.536665] hub 3-0:1.0: 4 ports detected [ 1.536785] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 1.536896] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4 [ 1.537061] xHCI xhci_add_endpoint called for root hub [ 1.537063] xHCI xhci_check_bandwidth called for root hub [ 1.537080] hub 4-0:1.0: USB hub found [ 1.537162] hub 4-0:1.0: 4 ports detected [ 1.599365] usbcore: registered new interface driver libusual [ 1.599477] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 1.602881] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.602966] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 1.603144] mousedev: PS/2 mouse device common for all mice [ 1.603347] rtc_cmos 00:06: RTC can wake from S4 [ 1.603530] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0 [ 1.603640] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs [ 1.603782] device-mapper: uevent: version 1.0.3 [ 1.603911] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] [ 1.604202] cpuidle: using governor ladder [ 1.604567] cpuidle: using governor menu [ 1.604644] EFI Variables Facility v0.08 2004-May-17 [ 1.604880] TCP cubic registered [ 1.605026] NET: Registered protocol family 10 [ 1.605419] NET: Registered protocol family 17 [ 1.605501] Registering the dns_resolver key type [ 1.605697] PM: Checking hibernation image partition UUID=e4918e2d-1704-43a6-93c0-93235d39768e [ 1.610263] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2 [ 1.815251] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.815355] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.820291] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded [ 1.820295] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out [ 1.820405] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out [ 1.823244] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 1.823835] ata2.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded [ 1.823839] ata2.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out [ 1.823949] ata2.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out [ 1.824480] ata2.00: ATA-9: M4-CT128M4SSD3, 04MH, max UDMA/100 [ 1.824566] ata2.00: 250069680 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 1.825286] ata2.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded [ 1.825290] ata2.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out [ 1.825405] ata2.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out [ 1.825521] ata1.00: ATA-8: WDC WD7500BPVT-24HXZT3, 03.01A03, max UDMA/133 [ 1.825611] ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 1.825955] ata2.00: configured for UDMA/100 [ 1.827234] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 1.827539] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded [ 1.827545] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out [ 1.827654] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out [ 1.830173] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded [ 1.830176] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out [ 1.830281] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out [ 1.830395] ata3.00: ATAPI: HL-DT-ST BDDVDRW CA30N, QD01, max UDMA/133 [ 1.835436] ata1.00: configured for UDMA/133 [ 1.835518] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded [ 1.835522] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out [ 1.835634] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out [ 1.835667] scsi 0:0:0:0: Direct-Access ATA WDC WD7500BPVT-2 03.0 PQ: 0 ANSI: 5 [ 1.835868] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.835973] sd 0:0:0:0: [sda] 1465149168 512-byte logical blocks: (750 GB/698 GiB) [ 1.836080] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 1.836232] scsi 1:0:0:0: Direct-Access ATA M4-CT128M4SSD3 04MH PQ: 0 ANSI: 5 [ 1.836409] sd 0:0:0:0: [sda] Write Protect is off [ 1.836473] sd 1:0:0:0: [sdb] 250069680 512-byte logical blocks: (128 GB/119 GiB) [ 1.836505] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 1.836522] sd 1:0:0:0: [sdb] Write Protect is off [ 1.836524] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1.836538] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.836875] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.836975] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.837092] sdb: sdb1 sdb2 sdb3 [ 1.837633] sd 1:0:0:0: [sdb] Attached SCSI disk [ 1.838349] ata3.00: configured for UDMA/133 [ 1.841874] scsi 2:0:0:0: CD-ROM HL-DT-ST BDDVDRW CA30N QD01 PQ: 0 ANSI: 5 [ 1.845428] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 1.845534] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 1.845742] sr 2:0:0:0: Attached scsi CD-ROM sr0 [ 1.845833] sr 2:0:0:0: Attached scsi generic sg2 type 5 [ 1.866172] sda: sda1 sda2 sda3 [ 1.867065] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.867187] PM: Hibernation image not present or could not be loaded. [ 1.867208] registered taskstats version 1 [ 1.874616] Magic number: 1:400:756 [ 1.874707] tty ttyS7: hash matches [ 1.874880] rtc_cmos 00:06: setting system clock to 2013-02-04 23:42:56 UTC (1360021376) [ 1.876190] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 1.876271] EDD information not available. [ 1.877445] Freeing unused kernel memory: 924k freed [ 1.877601] Write protecting the kernel read-only data: 12288k [ 1.880792] Freeing unused kernel memory: 1604k freed [ 1.883430] Freeing unused kernel memory: 1196k freed [ 1.895080] udevd[126]: starting version 175 [ 1.906173] acpi device:1a: registered as cooling_device8 [ 1.906321] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:18/LNXVIDEO:00/input/input3 [ 1.912851] ACPI: Video Device [VGA] (multi-head: yes rom: yes post: no) [ 1.915835] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 1.915950] r8169 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.916090] r8169 0000:03:00.0: setting latency timer to 64 [ 1.916181] r8169 0000:03:00.0: irq 43 for MSI/MSI-X [ 1.916573] r8169 0000:03:00.0: eth0: RTL8168evl/8111evl at 0xffffc90000c7e000, 04:7d:7b:b5:bd:c0, XID 0c900800 IRQ 43 [ 1.916696] r8169 0000:03:00.0: eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 1.959812] hub 1-1:1.0: USB hub found [ 1.960028] hub 1-1:1.0: 6 ports detected [ 2.071100] usb 2-1: new high-speed USB device number 2 using ehci_hcd [ 2.203683] hub 2-1:1.0: USB hub found [ 2.203906] hub 2-1:1.0: 6 ports detected [ 2.215026] Refined TSC clocksource calibration: 2294.785 MHz. [ 2.215122] Switching to clocksource tsc [ 2.370949] usb 3-3: new full-speed USB device number 2 using xhci_hcd [ 2.394165] usbcore: registered new interface driver usbhid [ 2.394247] usbhid: USB HID core driver [ 2.399686] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-3/input2 [ 2.403088] input: Logitech Unifying Device. Wireless PID:4017 as /devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3:1.2/0003:046D:C52B.0003/input/input4 [ 2.403385] logitech-djdevice 0003:046D:C52B.0004: input,hidraw1: USB HID v1.11 Mouse [Logitech Unifying Device. Wireless PID:4017] on usb-0000:00:14.0-3:1 [ 2.463079] usb 1-1.1: new full-speed USB device number 3 using ehci_hcd [ 2.557502] hub 1-1.1:1.0: USB hub found [ 2.557717] hub 1-1.1:1.0: 3 ports detected [ 2.626984] usb 1-1.2: new full-speed USB device number 4 using ehci_hcd [ 2.725180] generic-usb 0003:2619:5610.0006: hiddev0,hidraw2: USB HID v1.10 Device [Advanced Silicon S.A. CoolTouch(TM) System ] on usb-0000:00:1a.0-1.2/input1 [ 2.794902] usb 1-1.4: new high-speed USB device number 5 using ehci_hcd [ 2.958827] usb 1-1.5: new high-speed USB device number 6 using ehci_hcd [ 3.122716] usb 2-1.5: new full-speed USB device number 3 using ehci_hcd [ 3.222338] input: Lite-On Technology Corp. Lenovo silver silk (wireless) 2.4G K&M kit as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.5/2-1.5:1.0/input/input5 [ 3.222579] generic-usb 0003:17EF:6032.0007: input,hidraw3: USB HID v1.11 Keyboard [Lite-On Technology Corp. Lenovo silver silk (wireless) 2.4G K&M kit] on usb-0000:00:1d.0-1.5/input0 [ 3.227523] input: Lite-On Technology Corp. Lenovo silver silk (wireless) 2.4G K&M kit as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.5/2-1.5:1.1/input/input6 [ 3.227815] generic-usb 0003:17EF:6032.0008: input,hiddev0,hidraw4: USB HID v1.11 Device [Lite-On Technology Corp. Lenovo silver silk (wireless) 2.4G K&M kit] on usb-0000:00:1d.0-1.5/input1 [ 3.229667] input: Lite-On Technology Corp. Lenovo silver silk (wireless) 2.4G K&M kit as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.5/2-1.5:1.2/input/input7 [ 3.229920] generic-usb 0003:17EF:6032.0009: input,hidraw5: USB HID v1.11 Mouse [Lite-On Technology Corp. Lenovo silver silk (wireless) 2.4G K&M kit] on usb-0000:00:1d.0-1.5/input2 [ 3.302629] usb 1-1.1.1: new full-speed USB device number 7 using ehci_hcd [ 3.399736] input: HID 0a5c:4502 as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.0/input/input8 [ 3.399964] generic-usb 0003:0A5C:4502.000A: input,hidraw6: USB HID v1.11 Keyboard [HID 0a5c:4502] on usb-0000:00:1a.0-1.1.1/input0 [ 3.470563] usb 1-1.1.2: new full-speed USB device number 8 using ehci_hcd [ 3.568652] input: HID 0a5c:4503 as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1/1-1.1.2/1-1.1.2:1.0/input/input9 [ 3.568876] generic-usb 0003:0A5C:4503.000B: input,hidraw7: USB HID v1.11 Mouse [HID 0a5c:4503] on usb-0000:00:1a.0-1.1.2/input0 [ 3.638426] usb 1-1.1.3: new full-speed USB device number 9 using ehci_hcd [ 3.734597] EXT4-fs (sdb3): INFO: recovery required on readonly filesystem [ 3.734621] EXT4-fs (sdb3): write access will be enabled during recovery [ 3.735745] EXT4-fs (sdb3): recovery complete [ 3.735809] EXT4-fs (sdb3): mounted filesystem with ordered data mode. Opts: (null) [ 4.120836] Adding 8396796k swap on /dev/sdb2. Priority:-1 extents:1 across:8396796k SS [ 4.155028] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 4.163108] udevd[406]: starting version 175 [ 4.194110] lp: driver loaded but no devices found [ 4.235163] EXT4-fs (sdb3): re-mounted. Opts: errors=remount-ro [ 4.245271] wmi: Mapper loaded [ 4.254460] mei: module is from the staging directory, the quality is unknown, you have been warned. [ 4.254733] mei 0000:00:16.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4.254739] mei 0000:00:16.0: setting latency timer to 64 [ 4.254795] mei 0000:00:16.0: irq 44 for MSI/MSI-X [ 4.304140] nvidia: module license 'NVIDIA' taints kernel. [ 4.304143] Disabling lock debugging due to kernel taint [ 4.306802] Bluetooth: Core ver 2.16 [ 4.308532] NET: Registered protocol family 31 [ 4.308536] Bluetooth: HCI device and connection manager initialized [ 4.308539] Bluetooth: HCI socket layer initialized [ 4.308541] Bluetooth: L2CAP socket layer initialized [ 4.308548] Bluetooth: SCO socket layer initialized [ 4.333110] input: Advanced Silicon S.A. CoolTouch(TM) System as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input10 [ 4.333328] hid-multitouch 0003:2619:5610.0005: input,hidraw8: USB HID v1.10 Device [Advanced Silicon S.A. CoolTouch(TM) System ] on usb-0000:00:1a.0-1.2/input0 [ 4.337521] Linux video capture interface: v2.00 [ 4.340386] Bluetooth: Generic Bluetooth USB driver ver 0.6 [ 4.341558] nvidia 0000:01:00.0: power state changed by ACPI to D0 [ 4.341571] nvidia 0000:01:00.0: power state changed by ACPI to D0 [ 4.341601] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4.341621] nvidia 0000:01:00.0: setting latency timer to 64 [ 4.341632] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem [ 4.341772] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 310.14 Tue Oct 9 11:52:41 PDT 2012 [ 4.343377] uvcvideo: Found UVC 1.00 device Lenovo H264 720P Camera (17ef:4820) [ 4.344083] usbcore: registered new interface driver btusb [ 4.344086] uvcvideo: No streaming interface found for terminal 9. [ 4.344134] input: Lenovo H264 720P Camera as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.4/1-1.4:1.0/input/input11 [ 4.344200] usbcore: registered new interface driver uvcvideo [ 4.344202] USB Video Class driver (1.1.1) [ 4.380336] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 4.380382] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X [ 4.380406] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 4.425111] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 4.425198] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13 [ 4.425373] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 4.425375] hda_intel: Disabling MSI [ 4.425429] snd_hda_intel 0000:01:00.1: setting latency timer to 64 [ 5.216459] init: failsafe main process (982) killed by TERM signal [ 5.237454] HDMI status: Codec=0 Pin=5 Presence_Detect=0 ELD_Valid=0 [ 5.261442] HDMI status: Codec=1 Pin=5 Presence_Detect=0 ELD_Valid=0 [ 5.270394] ppdev: user-space parallel port driver [ 5.285461] HDMI status: Codec=2 Pin=5 Presence_Detect=0 ELD_Valid=0 [ 5.309427] HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0 [ 5.309548] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input14 [ 5.309644] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input15 [ 5.309750] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input16 [ 5.309847] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input17 [ 5.331530] init: alsa-restore main process (1033) terminated with status 99 [ 5.347185] Bluetooth: RFCOMM TTY layer initialized [ 5.347188] Bluetooth: RFCOMM socket layer initialized [ 5.347189] Bluetooth: RFCOMM ver 1.11 [ 5.349937] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 5.349939] Bluetooth: BNEP filters: protocol multicast [ 5.506343] init: udev-fallback-graphics main process (1135) terminated with status 1 [ 5.512231] init: kdm main process (1153) killed by TERM signal [ 5.514305] r8169 0000:03:00.0: eth0: link down [ 5.514593] init: gdm main process (1157) killed by TERM signal [ 5.514725] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 5.514912] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 6.183254] NVRM: GPU at 0000:01:00: GPU-01a21cf4-41d4-a898-dee1-10943c5d4112 [ 15.440075] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 183.369324] rtw driver version=v3.4.4_xxxx.20120730 [ 183.369330] Build at: Feb 4 2013 23:44:44 [ 183.369400] usbcore: registered new interface driver rtl8192cu [ 183.370696] register rtw_netdev_ops to netdev_ops [ 183.370702] CHIP TYPE: RTL8188C_8192C [ 183.370706] [ 183.370707] usb_endpoint_descriptor(0): [ 183.370710] bLength=7 [ 183.370711] bDescriptorType=5 [ 183.370713] bEndpointAddress=81 [ 183.370715] wMaxPacketSize=200 [ 183.370717] bInterval=0 [ 183.370719] RT_usb_endpoint_is_bulk_in = 1 [ 183.370721] [ 183.370722] usb_endpoint_descriptor(1): [ 183.370724] bLength=7 [ 183.370726] bDescriptorType=5 [ 183.370727] bEndpointAddress=2 [ 183.370729] wMaxPacketSize=200 [ 183.370731] bInterval=0 [ 183.370733] RT_usb_endpoint_is_bulk_out = 2 [ 183.370735] [ 183.370736] usb_endpoint_descriptor(2): [ 183.370738] bLength=7 [ 183.370739] bDescriptorType=5 [ 183.370741] bEndpointAddress=3 [ 183.370743] wMaxPacketSize=200 [ 183.370744] bInterval=0 [ 183.370746] RT_usb_endpoint_is_bulk_out = 3 [ 183.370748] [ 183.370749] usb_endpoint_descriptor(3): [ 183.370751] bLength=7 [ 183.370752] bDescriptorType=5 [ 183.370754] bEndpointAddress=84 [ 183.370756] wMaxPacketSize=40 [ 183.370758] bInterval=1 [ 183.370760] RT_usb_endpoint_is_int_in = 4, Interval = 1 [ 183.370762] nr_endpoint=4, in_num=2, out_num=2 [ 183.370764] [ 183.370765] USB_SPEED_HIGH [ 183.370905] Chip Version ID: VERSION_NORMAL_TSMC_CHIP_88C. [ 183.370912] RF_Type is 3!! [ 183.371259] EEPROM type is E-FUSE [ 183.371263] ====> ReadAdapterInfo8192C [ 183.371385] Boot from EFUSE, Autoload OK ! [ 183.556146] EEPROMVID = 0x0bda [ 183.556150] EEPROMPID = 0x819a [ 183.556152] EEPROMCustomerID : 0x00 [ 183.556154] EEPROMSubCustomerID: 0x00 [ 183.556156] RT_CustomerID: 0x00 [ 183.556159] _ReadMACAddress MAC Address from EFUSE = 00:1c:7b:a8:a8:f3 [ 183.556163] EEPROMRegulatory = 0x1 [ 183.556165] _ReadBoardType(3) [ 183.556167] BT Coexistance = disable [ 183.556170] RT_ChannelPlan: 0x0a [ 183.556172] _ReadPSSetting...bHWPwrPindetect(0)-bHWPowerdown(10) ,bSupportRemoteWakeup(0) [ 183.556176] ### PS params=> power_mgnt(1),usbss_enable(0) ### [ 183.556178] ### AntDivCfg(0) [ 183.556180] readAdapterInfo_8192CU(): REPLACEMENT = 1 [ 183.556184] <==== ReadAdapterInfo8192C in 184 ms [ 183.556432] rtw_macaddr_cfg MAC Address = 00:1c:7b:a8:a8:f3 [ 183.556436] MAC Address from pnetdev->dev_addr= 00:1c:7b:a8:a8:f3 [ 183.557231] bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0 [ 183.571360] bDriverStopped=1 [ 183.572190] +871x_drv - drv_open, bup=0 [ 183.576780] ===> FirmwareDownload91C() fw:Rtl819XFwImageArray_TSMC [ 183.576786] FirmwareDownload92C accquire FW from embedded image [ 183.576790] fw_ver=v80, fw_subver=0, sig=0x88c0 [ 183.608627] fw download ok! [ 183.608631] Set RF Chip ID to RF_6052 and RF type to 1T1R. [ 183.984930] IQK:Start!!! [ 183.996309] Path A IQK Success!! [ 184.004034] Path A IQK Success!! [ 184.008907] IQK: final_candidate is 0 [ 184.008911] IQK: RegE94=ff RegE9C=d RegEA4=fd RegEAC=3fd RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0 [ 184.008914] Path A IQ Calibration Success ! [ 184.122503] pdmpriv->TxPowerTrackControl = 1 [ 184.127472] MAC Address from REG_MACID = 00:1c:7b:a8:a8:f3 [ 184.127476] rtl8192cu_hal_init in 556ms [ 184.127480] MAC Address = 00:1c:7b:a8:a8:f3 [ 184.132257] -871x_drv - drv_open, bup=1 [ 184.133354] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 184.133824] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 184.133854] set_mode = IW_MODE_INFRA [ 184.150748] [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! [ 184.150763] set_mode = IW_MODE_INFRA [ 184.193691] [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! [ 185.543612] survey done event(25) [ 185.593007] IW_SCAN_THIS_ESSID, ssid=nicht dein WLAN, len=15 [ 186.942758] survey done event(2d) [ 186.943996] wpa_set_auth_algs, AUTH_ALG_OPEN_SYSTEM [ 186.944003] set_mode = IW_MODE_INFRA [ 186.944019] [ 186.944020] wpa_ie(length:22): [ 186.944024] 0x30 0x14 0x01 0x00 0x00 0x0f 0xac 0x02 [ 186.944028] 0x01 0x00 0x00 0x0f 0xac 0x04 0x01 0x00 [ 186.944031] 0x00 0x0f 0xac 0x02 0x00 0x00 0x00 0x00 [ 186.944045] =>rtw_wx_set_essid [ 186.944047] ssid=nicht dein WLAN, len=15 [ 186.944052] Set SSID under fw_state=0x00000008 [ 186.944058] [by_bssid:0][assoc_ssid:nicht dein WLAN][to_roaming:0] new candidate: nicht dein WLAN(00:15:0c:f1:0d:d0) rssi:-32 [ 186.944077] rtw_select_and_join_from_scanned_queue: candidate: nicht dein WLAN(00:15:0c:f1:0d:d0) [ 186.944090] link to new AP [ 186.944100] <=rtw_wx_set_essid, ret 0 [ 186.944110] Set BSSID under fw_state=0x00000088 [ 187.125476] link to new AP [ 187.125484] issue_deauth to 00:15:0c:f1:0d:d0 [ 187.129338] OnAuthClient [ 187.129349] network.SupportedRates[0]=82 [ 187.129351] network.SupportedRates[1]=84 [ 187.129353] network.SupportedRates[2]=8B [ 187.129356] network.SupportedRates[3]=96 [ 187.129358] network.SupportedRates[4]=2C [ 187.129360] network.SupportedRates[5]=0C [ 187.129362] network.SupportedRates[6]=12 [ 187.129364] network.SupportedRates[7]=18 [ 187.129366] network.SupportedRates[8]=24 [ 187.129368] network.SupportedRates[9]=30 [ 187.129370] network.SupportedRates[10]=48 [ 187.129372] network.SupportedRates[11]=60 [ 187.129374] network.SupportedRates[12]=6C [ 187.129377] issue_assocreq(): the rate[4]=2C is not supported by STA! [ 187.129380] bssrate_len = 12 [ 187.135954] OnAssocRsp [ 187.135977] report_join_res(1) [ 187.135983] rtw_joinbss_update_network [ 187.135994] rtw_joinbss_update_stainfo [ 187.136060] HW_VAR_BASIC_RATE: BrateCfg(0x15d) [ 187.137196] HTOnAssocRsp [ 187.137334] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 187.142408] update raid entry, mask=0x40000fff, arg=0x80 [ 187.143905] rtl8192c_set_FwJoinBssReport_cmd mstatus(1) [ 187.144776] SetFwRsvdPagePkt [ 187.144787] Set RSVD page location to Fw. [ 187.145453] [ 187.145455] ~~~~stastakey:unicastkey [ 187.145524] [ 187.145525] ~~~~stastakey:groupkey [ 187.145529] ==> rtw_set_key algorithm(2),keyid(2),key_mask(4) [ 187.145903] =>mlmeext_joinbss_event_callback [ 187.811595] rx bc/mc packets, to perform sw rtw_tkip_decrypt [ 188.141761] rtl8192c_dm_RF_Saving(): RF_Save [ 197.538636] wlan0: no IPv6 routers presenttommy@Tommy-AIO:~$ lsusb -v -d 0bda:819aBus 001 Device 006: ID 0bda:819a Realtek Semiconductor Corp. Couldn't open device, some information will be missing Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0bda Realtek Semiconductor Corp. idProduct 0x819a bcdDevice 2.00 iManufacturer 1 iProduct 2 iSerial 3 bNumConfigurations 1Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 46
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes0xa0
(Bus Powered)
Remote Wakeup
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 4
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress0x81EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize0x02001x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress0x02EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize0x02001x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress0x03EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize0x02001x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5Quoted 8 lines
bEndpointAddress
0x84EP 4 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize0x00401x 64 bytes
bInterval 1
tommy@Tommy-AIO:~$2013/2/4 Xose Vazquez Perez <[email protected]>:
Quoted 17 lines
Quoted 11 lines · Larry Finger
You are likely crashing more than X.
That is very good evidence that rtl8192cu is *NOT* the correct driver for that
device. As I recall Xose found that USB ID in a Windows driver, but who knows
what changes are inside that driver?I have what I think is a complete collection of Realtek drivers for Linux, and
none of them have 0bda:819a as a USB ID.He's using the
RTL8188C_8192C_USB_linuxdriver.
Therefore, there are only two possibilities:Quoted 7 lines
- it's a 8192_du device, or
- it's a 8192_cu device, and there is a bug in rtlwifi.Thomas, could you put "dmesg" output after loading 8192cu.ko (realtek driver) ?
and "lsusb -v -d 0bda:819a" output.2013/2/4 Xose Vazquez Perez <[email protected]>
Quoted 25 lines
Quoted 11 lines · Larry Finger
You are likely crashing more than X.
That is very good evidence that rtl8192cu is *NOT* the correct driver for that
device. As I recall Xose found that USB ID in a Windows driver, but who knows
what changes are inside that driver?I have what I think is a complete collection of Realtek drivers for Linux, and
none of them have 0bda:819a as a USB ID.He's using the
RTL8188C_8192C_USB_linuxdriver.
Therefore, there are only two possibilities:- it's a 8192_du device, or
- it's a 8192_cu device, and there is a bug in rtlwifi.Thomas, could you put "dmesg" output after loading 8192cu.ko (realtek driver) ?
and "lsusb -v -d 0bda:819a" output.
On 02/05/2013 12:00 AM, Thomas Rosenkranz wrote:
Larry, are you able to identify the chip of that device with the 8192cu output ?
what should he do ? open the device to see the chip ??
Quoted 225 lines
[ 183.369324] rtw driver version=v3.4.4_xxxx.20120730 [ 183.369330] Build at: Feb 4 2013 23:44:44 [ 183.369400] usbcore: registered new interface driver rtl8192cu [ 183.370696] register rtw_netdev_ops to netdev_ops [ 183.370702] CHIP TYPE: RTL8188C_8192C [ 183.370706] [ 183.370707] usb_endpoint_descriptor(0): [ 183.370710] bLength=7 [ 183.370711] bDescriptorType=5 [ 183.370713] bEndpointAddress=81 [ 183.370715] wMaxPacketSize=200 [ 183.370717] bInterval=0 [ 183.370719] RT_usb_endpoint_is_bulk_in = 1 [ 183.370721] [ 183.370722] usb_endpoint_descriptor(1): [ 183.370724] bLength=7 [ 183.370726] bDescriptorType=5 [ 183.370727] bEndpointAddress=2 [ 183.370729] wMaxPacketSize=200 [ 183.370731] bInterval=0 [ 183.370733] RT_usb_endpoint_is_bulk_out = 2 [ 183.370735] [ 183.370736] usb_endpoint_descriptor(2): [ 183.370738] bLength=7 [ 183.370739] bDescriptorType=5 [ 183.370741] bEndpointAddress=3 [ 183.370743] wMaxPacketSize=200 [ 183.370744] bInterval=0 [ 183.370746] RT_usb_endpoint_is_bulk_out = 3 [ 183.370748] [ 183.370749] usb_endpoint_descriptor(3): [ 183.370751] bLength=7 [ 183.370752] bDescriptorType=5 [ 183.370754] bEndpointAddress=84 [ 183.370756] wMaxPacketSize=40 [ 183.370758] bInterval=1 [ 183.370760] RT_usb_endpoint_is_int_in = 4, Interval = 1 [ 183.370762] nr_endpoint=4, in_num=2, out_num=2 [ 183.370764] [ 183.370765] USB_SPEED_HIGH [ 183.370905] Chip Version ID: VERSION_NORMAL_TSMC_CHIP_88C. [ 183.370912] RF_Type is 3!! [ 183.371259] EEPROM type is E-FUSE [ 183.371263] ====> ReadAdapterInfo8192C [ 183.371385] Boot from EFUSE, Autoload OK ! [ 183.556146] EEPROMVID = 0x0bda [ 183.556150] EEPROMPID = 0x819a [ 183.556152] EEPROMCustomerID : 0x00 [ 183.556154] EEPROMSubCustomerID: 0x00 [ 183.556156] RT_CustomerID: 0x00 [ 183.556159] _ReadMACAddress MAC Address from EFUSE = 00:1c:7b:a8:a8:f3 [ 183.556163] EEPROMRegulatory = 0x1 [ 183.556165] _ReadBoardType(3) [ 183.556167] BT Coexistance = disable [ 183.556170] RT_ChannelPlan: 0x0a [ 183.556172] _ReadPSSetting...bHWPwrPindetect(0)-bHWPowerdown(10) ,bSupportRemoteWakeup(0) [ 183.556176] ### PS params=> power_mgnt(1),usbss_enable(0) ### [ 183.556178] ### AntDivCfg(0) [ 183.556180] readAdapterInfo_8192CU(): REPLACEMENT = 1 [ 183.556184] <==== ReadAdapterInfo8192C in 184 ms [ 183.556432] rtw_macaddr_cfg MAC Address = 00:1c:7b:a8:a8:f3 [ 183.556436] MAC Address from pnetdev->dev_addr= 00:1c:7b:a8:a8:f3 [ 183.557231] bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0 [ 183.571360] bDriverStopped=1 [ 183.572190] +871x_drv - drv_open, bup=0 [ 183.576780] ===> FirmwareDownload91C() fw:Rtl819XFwImageArray_TSMC [ 183.576786] FirmwareDownload92C accquire FW from embedded image [ 183.576790] fw_ver=v80, fw_subver=0, sig=0x88c0 [ 183.608627] fw download ok! [ 183.608631] Set RF Chip ID to RF_6052 and RF type to 1T1R. [ 183.984930] IQK:Start!!! [ 183.996309] Path A IQK Success!! [ 184.004034] Path A IQK Success!! [ 184.008907] IQK: final_candidate is 0 [ 184.008911] IQK: RegE94=ff RegE9C=d RegEA4=fd RegEAC=3fd RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0 [ 184.008914] Path A IQ Calibration Success ! [ 184.122503] pdmpriv->TxPowerTrackControl = 1 [ 184.127472] MAC Address from REG_MACID = 00:1c:7b:a8:a8:f3 [ 184.127476] rtl8192cu_hal_init in 556ms [ 184.127480] MAC Address = 00:1c:7b:a8:a8:f3 [ 184.132257] -871x_drv - drv_open, bup=1 [ 184.133354] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 184.133824] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 184.133854] set_mode = IW_MODE_INFRA [ 184.150748] [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! [ 184.150763] set_mode = IW_MODE_INFRA [ 184.193691] [rtw_wx_set_pmkid] IW_PMKSA_FLUSH! [ 185.543612] survey done event(25) [ 185.593007] IW_SCAN_THIS_ESSID, ssid=nicht dein WLAN, len=15 [ 186.942758] survey done event(2d) [ 186.943996] wpa_set_auth_algs, AUTH_ALG_OPEN_SYSTEM [ 186.944003] set_mode = IW_MODE_INFRA [ 186.944019] [ 186.944020] wpa_ie(length:22): [ 186.944024] 0x30 0x14 0x01 0x00 0x00 0x0f 0xac 0x02 [ 186.944028] 0x01 0x00 0x00 0x0f 0xac 0x04 0x01 0x00 [ 186.944031] 0x00 0x0f 0xac 0x02 0x00 0x00 0x00 0x00 [ 186.944045] =>rtw_wx_set_essid [ 186.944047] ssid=nicht dein WLAN, len=15 [ 186.944052] Set SSID under fw_state=0x00000008 [ 186.944058] [by_bssid:0][assoc_ssid:nicht dein WLAN][to_roaming:0] new candidate: nicht dein WLAN(00:15:0c:f1:0d:d0) rssi:-32 [ 186.944077] rtw_select_and_join_from_scanned_queue: candidate: nicht dein WLAN(00:15:0c:f1:0d:d0) [ 186.944090] link to new AP [ 186.944100] <=rtw_wx_set_essid, ret 0 [ 186.944110] Set BSSID under fw_state=0x00000088 [ 187.125476] link to new AP [ 187.125484] issue_deauth to 00:15:0c:f1:0d:d0 [ 187.129338] OnAuthClient [ 187.129349] network.SupportedRates[0]=82 [ 187.129351] network.SupportedRates[1]=84 [ 187.129353] network.SupportedRates[2]=8B [ 187.129356] network.SupportedRates[3]=96 [ 187.129358] network.SupportedRates[4]=2C [ 187.129360] network.SupportedRates[5]=0C [ 187.129362] network.SupportedRates[6]=12 [ 187.129364] network.SupportedRates[7]=18 [ 187.129366] network.SupportedRates[8]=24 [ 187.129368] network.SupportedRates[9]=30 [ 187.129370] network.SupportedRates[10]=48 [ 187.129372] network.SupportedRates[11]=60 [ 187.129374] network.SupportedRates[12]=6C [ 187.129377] issue_assocreq(): the rate[4]=2C is not supported by STA! [ 187.129380] bssrate_len = 12 [ 187.135954] OnAssocRsp [ 187.135977] report_join_res(1) [ 187.135983] rtw_joinbss_update_network [ 187.135994] rtw_joinbss_update_stainfo [ 187.136060] HW_VAR_BASIC_RATE: BrateCfg(0x15d) [ 187.137196] HTOnAssocRsp [ 187.137334] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 187.142408] update raid entry, mask=0x40000fff, arg=0x80 [ 187.143905] rtl8192c_set_FwJoinBssReport_cmd mstatus(1) [ 187.144776] SetFwRsvdPagePkt [ 187.144787] Set RSVD page location to Fw. [ 187.145453] [ 187.145455] ~~~~stastakey:unicastkey [ 187.145524] [ 187.145525] ~~~~stastakey:groupkey [ 187.145529] ==> rtw_set_key algorithm(2),keyid(2),key_mask(4) [ 187.145903] =>mlmeext_joinbss_event_callback [ 187.811595] rx bc/mc packets, to perform sw rtw_tkip_decrypt [ 188.141761] rtl8192c_dm_RF_Saving(): RF_Save [ 197.538636] wlan0: no IPv6 routers presenttommy@Tommy-AIO:~$ lsusb -v -d 0bda:819aBus 001 Device 006: ID 0bda:819a Realtek Semiconductor Corp. Couldn't open device, some information will be missing Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor0x0bdaRealtek Semiconductor Corp.
idProduct0x819a
bcdDevice 2.00
iManufacturer 1
iProduct 2
iSerial 3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 46
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes0xa0
(Bus Powered)
Remote Wakeup
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 4
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress0x81EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize0x02001x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress0x02EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize0x02001x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress0x03EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize0x02001x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress0x84EP 4 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize0x00401x 64 bytes
bInterval 1
Quoted 6 lines · Xose Vazquez Perez
On 02/05/2013 12:00 AM, Thomas Rosenkranz wrote:
Larry, are you able to identify the chip of that device with the 8192cu output ?
what should he do ? open the device to see the chip ??
What difference does it make what chip it has? It is obviously some flavor of RTL8188CU/RTL8192CU that is different enough that it does not work with the kernel version of rtl8192cu. A few months ago, I ran across a new B-CUT RTL8188CE that took new programming for rtl8192ce, and I suspect this device also has the B-CUT chip.
The crash on unloading is a known fault of the vendor driver. It happens with devices that work OK with the standard rtl8192cu. I have no desire to find out what causes the crash.
If someone wants to supply me with a sample of this 0bda:819a device, I'll make it work in the kernel. I have no desire to try to purchase one on my own.
Larry
In Windows it calls "Realtek RTL8188CUS WLAN USB Slim Solo"
2013/2/5 Larry Finger <[email protected]>:
Quoted 28 lines · Xose Vazquez Perez
Quoted 7 lines · Thomas Rosenkranz
Larry, are you able to identify the chip of that device with the 8192cu output ?
what should he do ? open the device to see the chip ??
What difference does it make what chip it has? It is obviously some flavor of RTL8188CU/RTL8192CU that is different enough that it does not work with the kernel version of rtl8192cu. A few months ago, I ran across a new B-CUT RTL8188CE that took new programming for rtl8192ce, and I suspect this device also has the B-CUT chip.
The crash on unloading is a known fault of the vendor driver. It happens with devices that work OK with the standard rtl8192cu. I have no desire to find out what causes the crash.
If someone wants to supply me with a sample of this 0bda:819a device, I'll make it work in the kernel. I have no desire to try to purchase one on my own.
Larry
Quoted 4 lines · Larry Finger
What difference does it make what chip it has? It is obviously some flavor of RTL8188CU/RTL8192CU that is different enough that it does not work with the kernel version of rtl8192cu. A few months ago, I ran across a new B-CUT RTL8188CE that took new programming for rtl8192ce, and I suspect this device also has the B-CUT chip.
The crash on unloading is a known fault of the vendor driver. It happens with devices that work OK with the standard rtl8192cu. I have no desire to find out what causes the crash.
We were trying to know, loading the
_realtek_ driver, the chip of the device.
*Because*, as Thomas said before, doing:
# echo "0bda 819a" > /sys/bus/usb/drivers/rtl8192cu/new_id with the rtl8192cu _kernel driver_ He got a _panic of the system_ .
This is a severe bug in rtlwifi.
BTW, the device is RTL8188C/RF6052
Quoted 1 line
Quoted 1 line
[ 183.370905] Chip Version ID: VERSION_NORMAL_TSMC_CHIP_88C.
VERSION_NORMAL_TSMC_CHIP_88C = 0x0008
Quoted 1 line
Quoted 1 line
[ 183.608631] Set RF Chip ID to RF_6052 and RF type to 1T1R.
RF_6052 = 4
B-cut are these ones:
VERSION_NORMAL_UMC_CHIP_8723_1T1R_B_CUT = 0x1089 VERSION_NORMAL_UMC_CHIP_88C_B_CUT = 0x1088 VERSION_NORMAL_UMC_CHIP_92C_B_CUT = 0x10a8 VERSION_NORMAL_UMC_CHIP_92C_1T2R_B_CUT = 0x1090
thank you.
Quoted 10 lines · Xose Vazquez Perez
Quoted 4 lines · Larry Finger
What difference does it make what chip it has? It is obviously some flavor of RTL8188CU/RTL8192CU that is different enough that it does not work with the kernel version of rtl8192cu. A few months ago, I ran across a new B-CUT RTL8188CE that took new programming for rtl8192ce, and I suspect this device also has the B-CUT chip.
The crash on unloading is a known fault of the vendor driver. It happens with devices that work OK with the standard rtl8192cu. I have no desire to find out what causes the crash.
We were trying to know, loading the
_realtek_ driver, the chip of the device.
Quoted 6 lines
*Because*, as Thomas said before, doing:
# echo "0bda 819a" > /sys/bus/usb/drivers/rtl8192cu/new_id with the rtl8192cu _kernel driver_ He got a _panic of the system_ .This is a severe bug in rtlwifi.
Yes, but not a bug for the devices that it is supposed to support! No one ever says that their driver will support *future* devices! As I said earlier, there are newer versions of the RTL8188C chip that requires different programming, which may be the cause of the problem. On the other hand, the chip change did not cause a crash in rtl8192ce. I just didn't work very well. As I have no such device, I cannot test any changes; therefore, I will not make them. If you want to write patches that let that device work with the kernel driver, I will be happy to review them.
Larry
Quoted 3 lines · Larry Finger
Yes, but not a bug for the devices that it is supposed to support! No one ever says that their driver will support *future* devices! As I said earlier, there are newer versions of the RTL8188C chip that requires different programming, which may be the cause of the problem. On the other hand, the chip change did not cause a crash in rtl8192ce. I just didn't work very well. As I have no such device, I cannot test any changes; therefore, I will not make them. If you want to write patches that let that device work with the kernel driver, I will be happy to review them.
Then, remove the "new_id" facility of the driver.
*Or* fix the driver. rt2x00 handles correctly any
kind of unknown device.
usb 2-1.5: new high-speed USB device number 5 using ehci_hcd usb 2-1.5: New USB device found, idVendor=0bda, idProduct=8176 usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-1.5: Product: 802.11n WLAN Adapter
usb 2-1.5: Manufacturer: *Realtek*
usb 2-1.5: SerialNumber: 00e04c000001
# echo "0bda 8176" > /sys/bus/usb/drivers/rt2800usb/new_id
phy2 -> rt2800_init_eeprom: Error - Invalid RT chipset 0x0000 detected. phy2 -> rt2x00lib_probe_dev: Error - Failed to allocate device.
and it doesn't panic. The system works flawlessly after that, see:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=blob;f=drivers/net/wireless/rt2x00/rt2800lib.c;h=197b4466a5d2a44378f998fdefa2c221ae6124c6;hb=HEAD#l4798
rtlwifi also can do the same, -ENODEV in rtl8192cu/mac.c rtl92c_read_chip_version() at switch(rtlhal->version) default:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=blob;f=drivers/net/wireless/rtlwifi/rtl8192cu/mac.c;h=32ff959a0251bdf36cb69122b55a6fc438e3bdd0;hb=HEAD#l127
Quoted 10 lines · Xose Vazquez Perez
Quoted 3 lines · Larry Finger
Yes, but not a bug for the devices that it is supposed to support! No one ever says that their driver will support *future* devices! As I said earlier, there are newer versions of the RTL8188C chip that requires different programming, which may be the cause of the problem. On the other hand, the chip change did not cause a crash in rtl8192ce. I just didn't work very well. As I have no such device, I cannot test any changes; therefore, I will not make them. If you want to write patches that let that device work with the kernel driver, I will be happy to review them.
Then, remove the "
new_id" facility of the driver.*Or* fix the driver. rt2x00 handles correctly any
kind of unknown device.
The attached patch will fix the oops when a foreign new_id is inserted. I will be submitting it soon.
Larry
drivers/net/wireless/rtlwifi/usb.c +3 -0
@@ -977,6 +977,9 @@ int rtl_usb_probe(struct usb_interface *rtl_dbgp_flag_init (hw);/* Init IO handler */ _rtl_usb_io_handler_init (&udev->dev, hw); +if (!rtlpriv->cfg || !rtlpriv->cfg->ops || + !rtlpriv->cfg->ops->read_chip_version) +return -ENODEV ; rtlpriv->cfg->ops->read_chip_version (hw);/*like read eeprom and so on */ rtlpriv->cfg->ops->read_eeprom_info (hw);
Quoted 13 lines · Larry Finger
Quoted 4 lines
Then, remove the "
new_id" facility of the driver.*Or* fix the driver. rt2x00 handles correctly any
kind of unknown device.The attached patch will fix the oops when a foreign
new_idis inserted. I will be submitting it soon.Index:
wireless-testing-new/drivers/net/wireless/rtlwifi/usb.c
===================================================================
drivers/net/wireless/rtlwifi/usb.c int rtl_usb_probe(struct usb_interface * · line 985
Quoted 9 lines
drivers/net/wireless/rtlwifi/usb.c +3
-0@@ -977,6 +977,9 @@ int rtl_usb_probe(struct usb_interface *rtl_dbgp_flag_init (hw);/* Init IO handler */ _rtl_usb_io_handler_init (&udev->dev, hw); +if (!rtlpriv->cfg || !rtlpriv->cfg->ops || + !rtlpriv->cfg->ops->read_chip_version) +return -ENODEV ; rtlpriv->cfg->ops->read_chip_version (hw);/*like read eeprom and so on */ rtlpriv->cfg->ops->read_eeprom_info (hw);
How about pci devices(rtlwifi/pci.c) ?
thank you.