Add Gnublin board support
PATCH 1/1 Add Gnublin board support
Signed-off-by Zoltan Gyarmati <[email protected]>
--- board/gnublin/README | 52 +++++++++++++++++++++++++++++++++++++++++++++ configs/gnublin_defconfig | 16 ++++++++++++++ 2 files changed, 68 insertions(+) create mode 100644 board/gnublin/README create mode 100644 configs/gnublin_defconfig
board/gnublin/README new file +52 -0
@@ -0,0 +1,52 @@ +This the Buildroot support for the LPC3131 based Gnublin board (see here: +http://en.gnublin.org/) and for the Elektor Linux board +(http://www.elektor.com/news/elektor-presents-embedded-linux-made-easy.2147294. +lynkx) + +Unfortunately currently the AD and the pwm modules are not supported, i'm about +to add also those drivers as well to the current kernel later. + +Base kernel version: 3.7 (available here: +https://gitorious.org/linux-3-7-gnublin/linux-3-7-gnublin/commits/gnublin- +support) + +U-boot version: 2009.11 (available here: +https://gitorious.org/u-boot-gnublin-support/u-boot-gnublin-support) + + +Steps to create a bootable SD card (with the given config you need an at least +500 MB SD card): + +1.Config buildroot with the gnublin_defconfig: + +$ make gnublin_defconfig + +2.Tweak the config for your needs: + +$ make menuconfig + +3.Build: + +$ make + +4.Create two partitions on your SD card, one with type of BootIt (fdisk ID: df), +the size should be around 1M, and another partition with all of the left space +on the card, and with the type of normal DOS partition. + +5.From the output/images directory dump the u-boot image to the BootIt partition +(probably you have to modify the output /dev files according to your system): + +$ dd if=output/images/u-boot.bin of=/dev/sdc1 + +6.Dump the root fs image as well: + +$ dd if=output/images/rootfs.ext2 of=/dev/sdc2 + +7.Insert the SD card into the board's slot, and your board should boot up with +your newly created system. + +Any feedback/report is welcome on the mr.zoltan.gyarmati[at]gmail.com + + + +
configs/gnublin_defconfig new file +16 -0
@@ -0,0 +1,16 @@ +BR2_arm=y +BR2_arm926t=y +BR2_TARGET_GENERIC_ISSUE="Welcome to Gnublin" +BR2_TARGET_ROOTFS_EXT2=y +BR2_TARGET_ROOTFS_EXT2_BLOCKS=475000 +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_BOARDNAME="GNUBLIN" +BR2_TARGET_UBOOT_CUSTOM_GIT=y +BR2_TARGET_UBOOT_CUSTOM_GIT_REPO_URL="git://gitorious.org/u-boot-gnublin-support/u-boot-gnublin-support.git" +BR2_TARGET_UBOOT_CUSTOM_GIT_VERSION="2009.11_gnublin_support_v2" +BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_GIT=y +BR2_LINUX_KERNEL_CUSTOM_GIT_REPO_URL="git://gitorious.org/linux-3-7-gnublin/linux-3-7-gnublin.git" +BR2_LINUX_KERNEL_CUSTOM_GIT_VERSION="v3.7-gnublin-2" +BR2_LINUX_KERNEL_DEFCONFIG="gnublin" +BR2_LINUX_KERNEL_INSTALL_TARGET=y
Signature · 1 line
1.7.9.5
PATCH 1/1 Add Gnublin board support
configs/gnublin_defconfig line 14
Quoted 4 lines · Zoltan Gyarmati
configs/gnublin_defconfig new file +4
-0+BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_GIT=y +BR2_LINUX_KERNEL_CUSTOM_GIT_REPO_URL="git://gitorious.org/linux-3-7-gnublin/linux-3-7-gnublin.git" +BR2_LINUX_KERNEL_CUSTOM_GIT_VERSION="v3.7-gnublin-2"
Can you add these lines too?
+BR2_KERNEL_HEADERS_VERSION=y
+BR2_DEFAULT_KERNEL_VERSION="3.7"
These are to lock down on kernel headers.
It's not a problem at the moment since the default buildroot version is 3.7.x, but this will change in the future when 3.8, 3.9, so on are released and it's bad building a toolchain with newer headers than the running kernel (eventual breakage).
Thanks!