Skip to contentSkip to conversation

arm64: use x22 to save boot exception level

PATCH In review Andrew F. Davis 2 participants 4 messages Aug 28, 2019 – Sep 2, 2019 arm64

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 arm64: use x22 to save boot exception level

The exception level in which the kernel was entered needs to be saved for later. We do this by writing the exception level to memory. As this data is written with the MMU/cache off it will bypass any cache, after this we invalidate the address so that later reads from cacheable mappings do not read a stale cache line. The side effect of this invalidate is any existing cache line for this address in the same coherency domain will be cleaned and written into memory, possibly overwriting the data we just wrote. As this memory is treated as cacheable by already running cores it on not architecturally safe to perform any non-caching accesses to this memory anyway.

Lets avoid these issues altogether by moving the writing of the boot exception level to after MMU/caching has been enabled. Saving the boot state in unused register x22 until we can safely and coherently write out this data.

As the data is not written with the MMU off anymore we move the variable definition out of this section and into a regular C code data section.

---
 arch/arm64/kernel/head.S | 31 +++++++++++--------------------
 arch/arm64/kernel/smp.c  | 10 ++++++++++
 2 files changed, 21 insertions(+), 20 deletions(-)
arch/arm64/kernel/head.S +11 -20
index 2cdacd1c141b..4c71493742c5 100644
@@ -99,6 +99,7 @@ pe_header:
 	 *
 	 *  Register   Scope                      Purpose
 	 *  x21        stext() .. start_kernel()  FDT pointer passed at boot in x0
+	 *  x22        stext() .. start_kernel()  exception level core was booted
 	 *  x23        stext() .. start_kernel()  physical misalignment/KASLR offset
 	 *  x28        __create_page_tables()     callee preserved temp register
 	 *  x19/x20    __primary_switch()         callee preserved temp registers
@@ -108,7 +109,6 @@ ENTRY(stext)
 	bl	el2_setup			// Drop to EL1, w0=cpu_boot_mode
 	adrp	x23, __PHYS_OFFSET
 	and	x23, x23, MIN_KIMG_ALIGN - 1	// KASLR offset, defaults to 0
-	bl	set_cpu_boot_mode_flag
 	bl	__create_page_tables
 	/*
 	 * The following calls CPU setup code, see arch/arm64/mm/proc.S for
@@ -428,6 +428,8 @@ __primary_switched:
 	sub	x4, x4, x0			// the kernel virtual and
 	str_l	x4, kimage_voffset, x5		// physical mappings
 
+	bl	set_cpu_boot_mode_flag
+
 	// Clear BSS
 	adr_l	x0, __bss_start
 	mov	x1, xzr
@@ -470,7 +472,7 @@ EXPORT_SYMBOL(kimage_vaddr)
  * If we're fortunate enough to boot at EL2, ensure that the world is
  * sane before dropping to EL1.
  *
- * Returns either BOOT_CPU_MODE_EL1 or BOOT_CPU_MODE_EL2 in w0 if
+ * Returns either BOOT_CPU_MODE_EL1 or BOOT_CPU_MODE_EL2 in w22 if
  * booted in EL1 or EL2 respectively.
  */
 ENTRY(el2_setup)
@@ -480,7 +482,7 @@ ENTRY(el2_setup)
 	b.eq	1f
 	mov_q	x0, (SCTLR_EL1_RES1 | ENDIAN_SET_EL1)
 	msr	sctlr_el1, x0
-	mov	w0, #BOOT_CPU_MODE_EL1		// This cpu booted in EL1
+	mov	w22, #BOOT_CPU_MODE_EL1		// This cpu booted in EL1
 	isb
 	ret
 
@@ -593,7 +595,7 @@ set_hcr:
 
 	cbz	x2, install_el2_stub
 
-	mov	w0, #BOOT_CPU_MODE_EL2		// This CPU booted in EL2
+	mov	w22, #BOOT_CPU_MODE_EL2		// This CPU booted in EL2
 	isb
 	ret
 
@@ -632,7 +634,7 @@ install_el2_stub:
 		      PSR_MODE_EL1h)
 	msr	spsr_el2, x0
 	msr	elr_el2, lr
-	mov	w0, #BOOT_CPU_MODE_EL2		// This CPU booted in EL2
+	mov	w22, #BOOT_CPU_MODE_EL2		// This CPU booted in EL2
 	eret
 ENDPROC(el2_setup)
 
@@ -642,12 +644,10 @@ ENDPROC(el2_setup)
  */
 set_cpu_boot_mode_flag:
 	adr_l	x1, __boot_cpu_mode
-	cmp	w0, #BOOT_CPU_MODE_EL2
+	cmp	w22, #BOOT_CPU_MODE_EL2
 	b.ne	1f
-	add	x1, x1, #4
-1:	str	w0, [x1]			// This CPU has booted in EL1
-	dmb	sy
-	dc	ivac, x1			// Invalidate potentially stale cache line
+	add	x1, x1, #4			// This CPU has booted in EL2
+1:	str	w22, [x1]
 	ret
 ENDPROC(set_cpu_boot_mode_flag)
 
@@ -658,16 +658,7 @@ ENDPROC(set_cpu_boot_mode_flag)
  * sufficient alignment that the CWG doesn't overlap another section.
  */
 	.pushsection ".mmuoff.data.write", "aw"
-/*
- * We need to find out the CPU boot mode long after boot, so we need to
- * store it in a writable variable.
- *
- * This is not in .bss, because we set it sufficiently early that the boot-time
- * zeroing of .bss would clobber it.
- */
-ENTRY(__boot_cpu_mode)
-	.long	BOOT_CPU_MODE_EL2
-	.long	BOOT_CPU_MODE_EL1
+
 /*
  * The booting CPU updates the failed status @__early_cpu_boot_status,
  * with MMU turned off.
arch/arm64/kernel/smp.c +10 -0
index 018a33e01b0e..66bdcaf61a46 100644
@@ -65,6 +65,16 @@ struct secondary_data secondary_data;
 /* Number of CPUs which aren't online, but looping in kernel text. */
 int cpus_stuck_in_kernel;
 
+/*
+ * We need to find out the CPU boot mode long after boot, so we need to
+ * store it in a writable variable in early boot. Any core started in
+ * EL1 will write that to the first location, EL2 to the second. After
+ * all cores are started this allows us to check that all cores started
+ * in the same mode.
+ */
+u32 __boot_cpu_mode[2] = { BOOT_CPU_MODE_EL2, BOOT_CPU_MODE_EL1 };
+EXPORT_SYMBOL(__boot_cpu_mode);
+
 enum ipi_msg_type {
 	IPI_RESCHEDULE,
 	IPI_CALL_FUNC,
Signature · 1 line
2.17.1
reviewer
#1 lore raw

Hi Andrew,

Quoted 10 lines · Andrew F. Davis

The exception level in which the kernel was entered needs to be saved for later. We do this by writing the exception level to memory. As this data is written with the MMU/cache off it will bypass any cache, after this we invalidate the address so that later reads from cacheable mappings do not read a stale cache line. The side effect of this invalidate is any existing cache line for this address in the same coherency domain will be cleaned and written into memory, possibly overwriting the data we just wrote. As this memory is treated as cacheable by already running cores it on not architecturally safe to perform any non-caching accesses to this memory anyway.

Are you seeing an issue in practice here, or is this something that you've found by inspection?

If this is an issue in practice, can you tell me more about the system, i.e.

- Which CPU models do you see this with?
- Do you see this with the boot CPU, secondaries, or both?
- Do you have a system-level cache? If so, which model?
- Do you see this on bare-metal?
- Do you see this under a hypervisor? If so, which hypervisor?

We place __boot_cpu_mode in the .mmuoff.data.write section, which is only written with the MMU off (i.e. with non-cacheable accesses), such that the cached copy should always be clean and shouldn't be written back. Your description sounds like you're seeing a write-back, which is surprising and may indicate a bug elsewhere.

Depending on what exactly you're seeing, this could also be an issue for __early_cpu_boot_status and the early page table creation, so I'd like to understand that better.

Thanks,
Mark.

Quoted 137 lines

Lets avoid these issues altogether by moving the writing of the boot exception level to after MMU/caching has been enabled. Saving the boot state in unused register x22 until we can safely and coherently write out this data.

As the data is not written with the MMU off anymore we move the variable definition out of this section and into a regular C code data section.

---
 arch/arm64/kernel/head.S | 31 +++++++++++--------------------
 arch/arm64/kernel/smp.c  | 10 ++++++++++
 2 files changed, 21 insertions(+), 20 deletions(-)
arch/arm64/kernel/head.S +11 -20
index 2cdacd1c141b..4c71493742c5 100644
@@ -99,6 +99,7 @@ pe_header:
 	 *
 	 *  Register   Scope                      Purpose
 	 *  x21        stext() .. start_kernel()  FDT pointer passed at boot in x0
+	 *  x22        stext() .. start_kernel()  exception level core was booted
 	 *  x23        stext() .. start_kernel()  physical misalignment/KASLR offset
 	 *  x28        __create_page_tables()     callee preserved temp register
 	 *  x19/x20    __primary_switch()         callee preserved temp registers
@@ -108,7 +109,6 @@ ENTRY(stext)
 	bl	el2_setup			// Drop to EL1, w0=cpu_boot_mode
 	adrp	x23, __PHYS_OFFSET
 	and	x23, x23, MIN_KIMG_ALIGN - 1	// KASLR offset, defaults to 0
-	bl	set_cpu_boot_mode_flag
 	bl	__create_page_tables
 	/*
 	 * The following calls CPU setup code, see arch/arm64/mm/proc.S for
@@ -428,6 +428,8 @@ __primary_switched:
 	sub	x4, x4, x0			// the kernel virtual and
 	str_l	x4, kimage_voffset, x5		// physical mappings
 
+	bl	set_cpu_boot_mode_flag
+
 	// Clear BSS
 	adr_l	x0, __bss_start
 	mov	x1, xzr
@@ -470,7 +472,7 @@ EXPORT_SYMBOL(kimage_vaddr)
  * If we're fortunate enough to boot at EL2, ensure that the world is
  * sane before dropping to EL1.
  *
- * Returns either BOOT_CPU_MODE_EL1 or BOOT_CPU_MODE_EL2 in w0 if
+ * Returns either BOOT_CPU_MODE_EL1 or BOOT_CPU_MODE_EL2 in w22 if
  * booted in EL1 or EL2 respectively.
  */
 ENTRY(el2_setup)
@@ -480,7 +482,7 @@ ENTRY(el2_setup)
 	b.eq	1f
 	mov_q	x0, (SCTLR_EL1_RES1 | ENDIAN_SET_EL1)
 	msr	sctlr_el1, x0
-	mov	w0, #BOOT_CPU_MODE_EL1		// This cpu booted in EL1
+	mov	w22, #BOOT_CPU_MODE_EL1		// This cpu booted in EL1
 	isb
 	ret
 
@@ -593,7 +595,7 @@ set_hcr:
 
 	cbz	x2, install_el2_stub
 
-	mov	w0, #BOOT_CPU_MODE_EL2		// This CPU booted in EL2
+	mov	w22, #BOOT_CPU_MODE_EL2		// This CPU booted in EL2
 	isb
 	ret
 
@@ -632,7 +634,7 @@ install_el2_stub:
 		      PSR_MODE_EL1h)
 	msr	spsr_el2, x0
 	msr	elr_el2, lr
-	mov	w0, #BOOT_CPU_MODE_EL2		// This CPU booted in EL2
+	mov	w22, #BOOT_CPU_MODE_EL2		// This CPU booted in EL2
 	eret
 ENDPROC(el2_setup)
 
@@ -642,12 +644,10 @@ ENDPROC(el2_setup)
  */
 set_cpu_boot_mode_flag:
 	adr_l	x1, __boot_cpu_mode
-	cmp	w0, #BOOT_CPU_MODE_EL2
+	cmp	w22, #BOOT_CPU_MODE_EL2
 	b.ne	1f
-	add	x1, x1, #4
-1:	str	w0, [x1]			// This CPU has booted in EL1
-	dmb	sy
-	dc	ivac, x1			// Invalidate potentially stale cache line
+	add	x1, x1, #4			// This CPU has booted in EL2
+1:	str	w22, [x1]
 	ret
 ENDPROC(set_cpu_boot_mode_flag)
 
@@ -658,16 +658,7 @@ ENDPROC(set_cpu_boot_mode_flag)
  * sufficient alignment that the CWG doesn't overlap another section.
  */
 	.pushsection ".mmuoff.data.write", "aw"
-/*
- * We need to find out the CPU boot mode long after boot, so we need to
- * store it in a writable variable.
- *
- * This is not in .bss, because we set it sufficiently early that the boot-time
- * zeroing of .bss would clobber it.
- */
-ENTRY(__boot_cpu_mode)
-	.long	BOOT_CPU_MODE_EL2
-	.long	BOOT_CPU_MODE_EL1
+
 /*
  * The booting CPU updates the failed status @__early_cpu_boot_status,
  * with MMU turned off.
arch/arm64/kernel/smp.c +10 -0
index 018a33e01b0e..66bdcaf61a46 100644
@@ -65,6 +65,16 @@ struct secondary_data secondary_data;
 /* Number of CPUs which aren't online, but looping in kernel text. */
 int cpus_stuck_in_kernel;
 
+/*
+ * We need to find out the CPU boot mode long after boot, so we need to
+ * store it in a writable variable in early boot. Any core started in
+ * EL1 will write that to the first location, EL2 to the second. After
+ * all cores are started this allows us to check that all cores started
+ * in the same mode.
+ */
+u32 __boot_cpu_mode[2] = { BOOT_CPU_MODE_EL2, BOOT_CPU_MODE_EL1 };
+EXPORT_SYMBOL(__boot_cpu_mode);
+
 enum ipi_msg_type {
 	IPI_RESCHEDULE,
 	IPI_CALL_FUNC,
Signature · 1 line
2.17.1
#2 lore raw
Quoted 14 lines · Mark Rutland

Hi Andrew,

Quoted 10 lines · Andrew F. Davis

The exception level in which the kernel was entered needs to be saved for later. We do this by writing the exception level to memory. As this data is written with the MMU/cache off it will bypass any cache, after this we invalidate the address so that later reads from cacheable mappings do not read a stale cache line. The side effect of this invalidate is any existing cache line for this address in the same coherency domain will be cleaned and written into memory, possibly overwriting the data we just wrote. As this memory is treated as cacheable by already running cores it on not architecturally safe to perform any non-caching accesses to this memory anyway.

Quoted 3 lines

Are you seeing an issue in practice here, or is this something that you've found by inspection?

We are seeing an actual issue. And I do have a good idea what is causing it, let me answer your questions on the system then I'll explain below.

Quoted 4 lines

If this is an issue in practice, can you tell me more about the system, i.e.

- Which CPU models do you see this with?

A53s

Quoted 1 line

- Do you see this with the boot CPU, secondaries, or both?

Both

Quoted 1 line

- Do you have a system-level cache? If so, which model?

Yes, Custom design, Datasheet has some more details if needed:
http://www.ti.com/product/AM6548

Quoted 1 line

- Do you see this on bare-metal?

Not tested

Quoted 2 lines

- Do you see this under a hypervisor? If so, which hypervisor?

Not tested

Quoted 10 lines

We place __boot_cpu_mode in the .mmuoff.data.write section, which is only written with the MMU off (i.e. with non-cacheable accesses), such that the cached copy should always be clean and shouldn't be written back. Your description sounds like you're seeing a write-back, which is surprising and may indicate a bug elsewhere.

Depending on what exactly you're seeing, this could also be an issue for __early_cpu_boot_status and the early page table creation, so I'd like to understand that better.

We are seeing is a write-back from L3 cache. Our bootloader writes the kernel image with caches on, then after turning off caching but before handing off to Linux it clean/invalidates all cache lines by set/way. This cleans out the L1/L2 but leaves dirty lines in L3. Our platform doesn't really have a good way to clean L3 as it only provides cache maintenance operations by VA, not by line, so we would need to clean every VA address manually..

Also want to point out, although this isn't a problem for most platforms what this code does here, with writing to a location as non-cacheable, is not architecturally safe as the running cores that do the reads have this section marked as cacheable when they read, therefor you have mismatched attributes. When this happens like this according to the ARM ARM we should do a cache invalidate after the write *and* before the read, which we do not do.

I would like to work this fix from the U-Boot side also, but in parallel I would like to reduce the mismatched attributes as much as possible on the kernel side like done here. So yes, we still will have issue with __early_cpu_boot_status, but that only seems to be needed in the failure to boot case, I'd like to fix that up as well at some later point.

As for early page table, since U-Boot doesn't write anything to those addresses (__boot_cpu_mode is in the data section and so written by the loader), they seem to be safe for now (I can break them by writing to all memory locations to dirty up the caches).

Thanks,
Andrew

Quoted 140 lines

Thanks,
Mark.

Quoted 137 lines

Lets avoid these issues altogether by moving the writing of the boot exception level to after MMU/caching has been enabled. Saving the boot state in unused register x22 until we can safely and coherently write out this data.

As the data is not written with the MMU off anymore we move the variable definition out of this section and into a regular C code data section.

---
 arch/arm64/kernel/head.S | 31 +++++++++++--------------------
 arch/arm64/kernel/smp.c  | 10 ++++++++++
 2 files changed, 21 insertions(+), 20 deletions(-)
arch/arm64/kernel/head.S +11 -20
index 2cdacd1c141b..4c71493742c5 100644
@@ -99,6 +99,7 @@ pe_header:
 	 *
 	 *  Register   Scope                      Purpose
 	 *  x21        stext() .. start_kernel()  FDT pointer passed at boot in x0
+	 *  x22        stext() .. start_kernel()  exception level core was booted
 	 *  x23        stext() .. start_kernel()  physical misalignment/KASLR offset
 	 *  x28        __create_page_tables()     callee preserved temp register
 	 *  x19/x20    __primary_switch()         callee preserved temp registers
@@ -108,7 +109,6 @@ ENTRY(stext)
 	bl	el2_setup			// Drop to EL1, w0=cpu_boot_mode
 	adrp	x23, __PHYS_OFFSET
 	and	x23, x23, MIN_KIMG_ALIGN - 1	// KASLR offset, defaults to 0
-	bl	set_cpu_boot_mode_flag
 	bl	__create_page_tables
 	/*
 	 * The following calls CPU setup code, see arch/arm64/mm/proc.S for
@@ -428,6 +428,8 @@ __primary_switched:
 	sub	x4, x4, x0			// the kernel virtual and
 	str_l	x4, kimage_voffset, x5		// physical mappings
 
+	bl	set_cpu_boot_mode_flag
+
 	// Clear BSS
 	adr_l	x0, __bss_start
 	mov	x1, xzr
@@ -470,7 +472,7 @@ EXPORT_SYMBOL(kimage_vaddr)
  * If we're fortunate enough to boot at EL2, ensure that the world is
  * sane before dropping to EL1.
  *
- * Returns either BOOT_CPU_MODE_EL1 or BOOT_CPU_MODE_EL2 in w0 if
+ * Returns either BOOT_CPU_MODE_EL1 or BOOT_CPU_MODE_EL2 in w22 if
  * booted in EL1 or EL2 respectively.
  */
 ENTRY(el2_setup)
@@ -480,7 +482,7 @@ ENTRY(el2_setup)
 	b.eq	1f
 	mov_q	x0, (SCTLR_EL1_RES1 | ENDIAN_SET_EL1)
 	msr	sctlr_el1, x0
-	mov	w0, #BOOT_CPU_MODE_EL1		// This cpu booted in EL1
+	mov	w22, #BOOT_CPU_MODE_EL1		// This cpu booted in EL1
 	isb
 	ret
 
@@ -593,7 +595,7 @@ set_hcr:
 
 	cbz	x2, install_el2_stub
 
-	mov	w0, #BOOT_CPU_MODE_EL2		// This CPU booted in EL2
+	mov	w22, #BOOT_CPU_MODE_EL2		// This CPU booted in EL2
 	isb
 	ret
 
@@ -632,7 +634,7 @@ install_el2_stub:
 		      PSR_MODE_EL1h)
 	msr	spsr_el2, x0
 	msr	elr_el2, lr
-	mov	w0, #BOOT_CPU_MODE_EL2		// This CPU booted in EL2
+	mov	w22, #BOOT_CPU_MODE_EL2		// This CPU booted in EL2
 	eret
 ENDPROC(el2_setup)
 
@@ -642,12 +644,10 @@ ENDPROC(el2_setup)
  */
 set_cpu_boot_mode_flag:
 	adr_l	x1, __boot_cpu_mode
-	cmp	w0, #BOOT_CPU_MODE_EL2
+	cmp	w22, #BOOT_CPU_MODE_EL2
 	b.ne	1f
-	add	x1, x1, #4
-1:	str	w0, [x1]			// This CPU has booted in EL1
-	dmb	sy
-	dc	ivac, x1			// Invalidate potentially stale cache line
+	add	x1, x1, #4			// This CPU has booted in EL2
+1:	str	w22, [x1]
 	ret
 ENDPROC(set_cpu_boot_mode_flag)
 
@@ -658,16 +658,7 @@ ENDPROC(set_cpu_boot_mode_flag)
  * sufficient alignment that the CWG doesn't overlap another section.
  */
 	.pushsection ".mmuoff.data.write", "aw"
-/*
- * We need to find out the CPU boot mode long after boot, so we need to
- * store it in a writable variable.
- *
- * This is not in .bss, because we set it sufficiently early that the boot-time
- * zeroing of .bss would clobber it.
- */
-ENTRY(__boot_cpu_mode)
-	.long	BOOT_CPU_MODE_EL2
-	.long	BOOT_CPU_MODE_EL1
+
 /*
  * The booting CPU updates the failed status @__early_cpu_boot_status,
  * with MMU turned off.
arch/arm64/kernel/smp.c +10 -0
index 018a33e01b0e..66bdcaf61a46 100644
@@ -65,6 +65,16 @@ struct secondary_data secondary_data;
 /* Number of CPUs which aren't online, but looping in kernel text. */
 int cpus_stuck_in_kernel;
 
+/*
+ * We need to find out the CPU boot mode long after boot, so we need to
+ * store it in a writable variable in early boot. Any core started in
+ * EL1 will write that to the first location, EL2 to the second. After
+ * all cores are started this allows us to check that all cores started
+ * in the same mode.
+ */
+u32 __boot_cpu_mode[2] = { BOOT_CPU_MODE_EL2, BOOT_CPU_MODE_EL1 };
+EXPORT_SYMBOL(__boot_cpu_mode);
+
 enum ipi_msg_type {
 	IPI_RESCHEDULE,
 	IPI_CALL_FUNC,
Signature · 1 line
2.17.1
reviewer
#3 lore raw
Quoted 10 lines · Andrew F. Davis
Quoted 1 line · Mark Rutland

On Wed, Aug 28, 2019 at 01:33:18PM -0400, Andrew F. Davis wrote:

We are seeing is a write-back from L3 cache. Our bootloader writes the kernel image with caches on, then after turning off caching but before handing off to Linux it clean/invalidates all cache lines by set/way. This cleans out the L1/L2 but leaves dirty lines in L3. Our platform doesn't really have a good way to clean L3 as it only provides cache maintenance operations by VA, not by line, so we would need to clean every VA address manually..

Ensuring that the Image is clean to the PoC is required by the arm64 boot protocol, which states that maintenance by VA may be necessary in the presence of a system cache. See:

https://www.kernel.org/doc/html/latest/arm64/booting.html

... which states:

| The MMU must be off. Instruction cache may be on or off. The address
| range corresponding to the loaded kernel image must be cleaned to the
| PoC. In the presence of a system cache or other coherent masters with
| caches enabled, this will typically require cache maintenance by VA
| rather than set/way operations. 

Please fix your bootloader to meet this requirement. The kernel is not in a position to fix this up, e.g. as while the MMU is off instruction fetches could fetch stale data from the PoC.

You only need to clean the kernel Image to the PoC, rather than all of memory, so you should be able to do that with a loop of DC CVAC instructions covering the VA range of the kernel Image.

Quoted 7 lines

Also want to point out, although this isn't a problem for most platforms what this code does here, with writing to a location as non-cacheable, is not architecturally safe as the running cores that do the reads have this section marked as cacheable when they read, therefor you have mismatched attributes. When this happens like this according to the ARM ARM we should do a cache invalidate after the write *and* before the

Quoted 5 lines

I would like to work this fix from the U-Boot side also, but in parallel I would like to reduce the mismatched attributes as much as possible on the kernel side like done here. So yes, we still will have issue with __early_cpu_boot_status, but that only seems to be needed in the failure to boot case, I'd like to fix that up as well at some later point.

If you haven't cleaned the Image to the PoC, there's no guarantee that any portion of it can be safely executed with the MMU off, so I don't think that makes sense -- please fix your bootloader first.

I am aware that there are potential problems with mismatched attributes, the primary issue here being unexpected-data-cache-hit. However, were that to occur no amount of cache maintenance can save us in the presence of a live cacheable alias. Practically speaking that's mainly a problem for virtual environments.

Thanks,
Mark.