mv-usb phy enhancement patches
Subsystems (5)
v7 cover mv-usb phy enhancement patches
The patches are divied into 2 parts
1. PHY driver
To remove the callbacks in the platform data, a usb PHY driver for marvell udc/otg/ehci is written.
For device tree support, it is not good to pass the callback pointers by platform data. The PHY driver also removes the block.
usb: phy: mv_usb2: add PHY driver for marvell usb2 controller
usb: gadget: mv_udc: use PHY driver for udc
usb: ehci: ehci-mv: use PHY driver for ehci
usb: otg: mv_otg: use PHY driver for otg
Above patches are marvell usb PHY driver support.
arm: mmp2: change the defintion of usb devices
arm: pxa910: change the defintion of usb devices
arm: brownstone: add usb support for the board
arm: ttc_dkb: add usb support
arm: mmp: remove the usb phy setting
arm: mmp: remove usb devices from pxa168
Above patches are for SOC/board support for marvell usb PHY driver.
2. external chip support
The marvell usb controller can detect the vbus/idpin, but it need PHY and usb clocks to be enabled.
Based on measurement it will import 15mA current, and increase the power when the usb is not used.
Using a external chip to detect vbus/idpin changes will save the power.
In fact the marvell PMIC 88pm860x and 88pm80x can do it. The drivers are located at drivers/mfd.
So add a middle layer in the marvell usb PHY driver. PMIC call the APIs in middle driver to registers the callback for vbus/idpin detection/query
udc/otg/ehci driver will call the APIs to get vbus/idpin changes and query the states of the vbus/idpin.
usb: phy: mv_usb2_phy: add externel chip support
usb: gadget: mv_udc: add extern chip support
usb: ehci: ehci-mv: add extern chip support
usb: otg: mv_otg: add extern chip support
Above patches are the middle layer suppor for udc/otg/ehci
arm: mmp: add extern chip support for brownstone
arm: mmp: add extern chip support for ttc_dkb
Above patches are corresponding board file changes
V2->V1:
Change the Signed-off-by to be right email address
v3->v2
re-format the patches to new code base
v4->v3
1. make mv udc gadget driver depend on ARCH_PXA and ARCH_MMP
2. remove __devinit and __devexit
3. make the driver compiled successful if CONFIG_MV_USB2_PHY is not defined. The modified patches are
usb: gadget: mv_udc: make mv_udc depends on ARCH_MMP or ARCH_PXA
usb: phy: mv_usb2: add PHY driver for marvell usb2 controller
v5->v4
make the struct mv_usb2_extern_chip member ->head to be struct atomic_notifier_head instead of struct atomic_notifier_head *.
v6->v5
the bug fix patches are merged.
Removed the dependcy of ARCH_MMP and ARCH_PXA, and make the driver can be compiled for x86.
The device tree support patches need modification, remove them from this patch series, and they will be submitted in another series.
v7->v6
Use usb_add_phy_dev and related APIs to add PHY drivers. Removed the device tree support in PHY driver. It will be added in another patch series.
Chao Xie (16):
usb: phy: mv_usb2: add PHY driver for marvell usb2 controller
usb: gadget: mv_udc: use PHY driver for udc
usb: ehci: ehci-mv: use PHY driver for ehci
usb: otg: mv_otg: use PHY driver for otg
arm: mmp2: change the defintion of usb devices
arm: pxa910: change the defintion of usb devices
arm: brownstone: add usb support for the board
arm: ttc_dkb: add usb support
arm: mmp: remove the usb phy setting
arm: mmp: remove usb devices from pxa168
usb: phy: mv_usb2_phy: add externel chip support
usb: gadget: mv_udc: add extern chip support
usb: ehci: ehci-mv: add extern chip support
usb: otg: mv_otg: add extern chip support
arm: mmp: add extern chip support for brownstone
arm: mmp: add extern chip support for ttc_dkb
arch/arm/mach-mmp/brownstone.c | 66 +++++ arch/arm/mach-mmp/devices.c | 278 ------------------ arch/arm/mach-mmp/include/mach/mmp2.h | 4 + arch/arm/mach-mmp/include/mach/pxa910.h | 7 +- arch/arm/mach-mmp/include/mach/regs-usb.h | 253 ----------------- arch/arm/mach-mmp/mmp2.c | 4 + arch/arm/mach-mmp/pxa168.c | 42 --- arch/arm/mach-mmp/pxa910.c | 4 + arch/arm/mach-mmp/ttc_dkb.c | 52 +++- drivers/usb/gadget/mv_udc.h | 5 +- drivers/usb/gadget/mv_udc_core.c | 93 ++++--- drivers/usb/host/ehci-mv.c | 62 ++--- drivers/usb/otg/mv_otg.c | 123 ++++----- drivers/usb/otg/mv_otg.h | 5 +- drivers/usb/phy/Kconfig | 7 + drivers/usb/phy/Makefile | 1 + drivers/usb/phy/mv_usb2_phy.c | 441 +++++++++++++++++++++++++++++ include/linux/platform_data/mv_usb.h | 22 +- include/linux/usb/mv_usb2.h | 121 ++++++++ 19 files changed, 843 insertions(+), 747 deletions(-) delete mode 100644 arch/arm/mach-mmp/include/mach/regs-usb.h create mode 100644 drivers/usb/phy/mv_usb2_phy.c create mode 100644 include/linux/usb/mv_usb2.h
Signature · 1 line
1.7.4.1
PATCH v7 1/16 usb: phy: mv_usb2: add PHY driver for marvell usb2 controller
The PHY is seperated from usb controller.
The usb controller used in marvell pxa168/pxa910/mmp2 are same, but PHY initialization may be different.
the usb controller can support udc/otg/ehci, and for each of the mode, it need PHY to initialized before use the controller. Direclty writing the phy driver will make the usb controller driver to be simple and portable.
The PHY driver will be used by marvell udc/otg/ehci.
--- drivers/usb/phy/Kconfig | 7 + drivers/usb/phy/Makefile | 1 + drivers/usb/phy/mv_usb2_phy.c | 392 ++++++++++++++++++++++++++++++++++ include/linux/platform_data/mv_usb.h | 9 +- include/linux/usb/mv_usb2.h | 40 ++++ 5 files changed, 446 insertions(+), 3 deletions(-) create mode 100644 drivers/usb/phy/mv_usb2_phy.c create mode 100644 include/linux/usb/mv_usb2.h
drivers/usb/phy/Kconfig +7 -0
@@ -73,3 +73,10 @@ config SAMSUNG_USBPHY help Enable this to support Samsung USB phy controller for samsung SoCs. + +config MV_USB2_PHY + tristate "Marvell USB 2.0 PHY Driver" + depends on USB || USB_GADGET + help + Enable this to support Marvell USB 2.0 phy driver for Marvell + SoC.
drivers/usb/phy/Makefile +1 -0
@@ -12,3 +12,4 @@ obj-$(CONFIG_MV_U3D_PHY) += mv_u3d_phy.o obj-$(CONFIG_USB_EHCI_TEGRA) += tegra_usb_phy.o obj-$(CONFIG_USB_RCAR_PHY) += rcar-phy.o obj-$(CONFIG_SAMSUNG_USBPHY) += samsung-usbphy.o +obj-$(CONFIG_MV_USB2_PHY) += mv_usb2_phy.o
drivers/usb/phy/mv_usb2_phy.c new file +392 -0
392 lines not on this page · raw message
include/linux/platform_data/mv_usb.h +6 -3
@@ -47,9 +47,12 @@ struct mv_usb_platform_data {/* Force a_bus_req to be asserted */ unsigned int otg_force_a_bus_req:1; -int (*phy_init)(void __iomem *regbase); -void (*phy_deinit)(void __iomem *regbase); int (*set_vbus)(unsigned int vbus); - int (*private_init)(void __iomem *opregs, void __iomem *phyregs); }; + +struct mv_usb_phy_platform_data { +unsigned int clknum; +char **clkname; +}; +#endif
include/linux/usb/mv_usb2.h new file +40 -0
@@ -0,0 +1,40 @@ +/* +* Copyright (C) 2012 Marvell Inc. +* +* This software is licensed under the terms of the GNU General Public +* License version 2, as published by the Free Software Foundation, and +* may be copied, distributed, and modified under those terms. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +*/ + +#ifndef __MV_USB2_H +#define __MV_USB2_H + +#define MV_USB2_PHY_INDEX 0 +#define MV_USB2_OTG_PHY_INDEX 1 + +struct mv_usb2_phy { +struct usb_phy phy; +struct platform_device *pdev; +struct mutex phy_lock; +unsigned int refcount; +unsigned int type; +void __iomem *base; +struct clk **clks; +unsigned int clks_num; +}; + +#if defined(CONFIG_MV_USB2_PHY ) || defined(CONFIG_MV_USB2_PHY_MODULE ) + + +#else + + +#endif + +#endif
Signature · 1 line
1.7.4.1
PATCH v7 1/16 usb: phy: mv_usb2: add PHY driver for marvell usb2 controller
Hi,
Quoted 170 lines · Chao Xie
The PHY is seperated from usb controller.
The usb controller used in marvell pxa168/pxa910/mmp2 are same, but PHY initialization may be different.
the usb controller can support udc/otg/ehci, and for each of the mode, it need PHY to initialized before use the controller. Direclty writing the phy driver will make the usb controller driver to be simple and portable.
The PHY driver will be used by marvell udc/otg/ehci.Signed-off-by Chao Xie <[email protected]>--- drivers/usb/phy/Kconfig | 7 + drivers/usb/phy/Makefile | 1 + drivers/usb/phy/mv_usb2_phy.c | 392 ++++++++++++++++++++++++++++++++++ include/linux/platform_data/mv_usb.h | 9 +- include/linux/usb/mv_usb2.h | 40 ++++ 5 files changed, 446 insertions(+), 3 deletions(-)create mode 100644
drivers/usb/phy/mv_usb2_phy.ccreate mode 100644include/linux/usb/mv_usb2.hdrivers/usb/phy/Kconfig +7
-0@@ -73,3 +73,10 @@ config SAMSUNG_USBPHY help Enable this to support Samsung USB phy controller for samsung SoCs. + +config MV_USB2_PHY + tristate "Marvell USB 2.0 PHY Driver" + depends on USB || USB_GADGET + help + Enable this to support Marvell USB 2.0 phy driver for Marvell + SoC.drivers/usb/phy/Makefile +1
-0@@ -12,3 +12,4 @@ obj-$(CONFIG_MV_U3D_PHY) += mv_u3d_phy.o obj-$(CONFIG_USB_EHCI_TEGRA) += tegra_usb_phy.o obj-$(CONFIG_USB_RCAR_PHY) += rcar-phy.o obj-$(CONFIG_SAMSUNG_USBPHY) += samsung-usbphy.o +obj-$(CONFIG_MV_USB2_PHY) += mv_usb2_phy.odrivers/usb/phy/mv_usb2_phy.c new file +120
-0@@ -0,0 +1,392 @@ +/* +* Copyright (C) 2010 Google, Inc. +* +* Author: +* Chao Xie <[email protected]> +* +* This software is licensed under the terms of the GNU General Public +* License version 2, as published by the Free Software Foundation, and +* may be copied, distributed, and modified under those terms. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +*/ + +#include <linux/resource.h> +#include <linux/delay.h> +#include <linux/slab.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/io.h> +#include <linux/err.h> +#include <linux/clk.h> +#include <linux/export.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/platform_data/mv_usb.h> +#include <linux/usb/phy.h> +#include <linux/usb/mv_usb2.h> + +/* phy regs */ +#define UTMI_REVISION 0x0 +#define UTMI_CTRL 0x4 +#define UTMI_PLL 0x8 +#define UTMI_TX 0xc +#define UTMI_RX 0x10 +#define UTMI_IVREF 0x14 +#define UTMI_T0 0x18 +#define UTMI_T1 0x1c +#define UTMI_T2 0x20 +#define UTMI_T3 0x24 +#define UTMI_T4 0x28 +#define UTMI_T5 0x2c +#define UTMI_RESERVE 0x30 +#define UTMI_USB_INT 0x34 +#define UTMI_DBG_CTL 0x38 +#define UTMI_OTG_ADDON 0x3c + +/* For UTMICTRL Register */ +#define UTMI_CTRL_USB_CLK_EN (1 << 31) +/* pxa168 */ +#define UTMI_CTRL_SUSPEND_SET1 (1 << 30) +#define UTMI_CTRL_SUSPEND_SET2 (1 << 29) +#define UTMI_CTRL_RXBUF_PDWN (1 << 24) +#define UTMI_CTRL_TXBUF_PDWN (1 << 11) + +#define UTMI_CTRL_INPKT_DELAY_SHIFT 30 +#define UTMI_CTRL_INPKT_DELAY_SOF_SHIFT 28 +#define UTMI_CTRL_PU_REF_SHIFT 20 +#define UTMI_CTRL_ARC_PULLDN_SHIFT 12 +#define UTMI_CTRL_PLL_PWR_UP_SHIFT 1 +#define UTMI_CTRL_PWR_UP_SHIFT 0 + +/* For UTMI_PLL Register */ +#define UTMI_PLL_PLLCALI12_SHIFT 29 +#define UTMI_PLL_PLLCALI12_MASK (0x3 << 29) + +#define UTMI_PLL_PLLVDD18_SHIFT 27 +#define UTMI_PLL_PLLVDD18_MASK (0x3 << 27) + +#define UTMI_PLL_PLLVDD12_SHIFT 25 +#define UTMI_PLL_PLLVDD12_MASK (0x3 << 25) + +#define UTMI_PLL_CLK_BLK_EN_SHIFT 24 +#define CLK_BLK_EN (0x1 << 24) +#define PLL_READY (0x1 << 23) +#define KVCO_EXT (0x1 << 22) +#define VCOCAL_START (0x1 << 21) + +#define UTMI_PLL_KVCO_SHIFT 15 +#define UTMI_PLL_KVCO_MASK (0x7 << 15) + +#define UTMI_PLL_ICP_SHIFT 12 +#define UTMI_PLL_ICP_MASK (0x7 << 12) + +#define UTMI_PLL_FBDIV_SHIFT 4 +#define UTMI_PLL_FBDIV_MASK (0xFF << 4) + +#define UTMI_PLL_REFDIV_SHIFT 0 +#define UTMI_PLL_REFDIV_MASK (0xF << 0) + +/* For UTMI_TX Register */ +#define UTMI_TX_REG_EXT_FS_RCAL_SHIFT 27 +#define UTMI_TX_REG_EXT_FS_RCAL_MASK (0xf << 27) + +#define UTMI_TX_REG_EXT_FS_RCAL_EN_SHIFT 26 +#define UTMI_TX_REG_EXT_FS_RCAL_EN_MASK (0x1 << 26) + +#define UTMI_TX_TXVDD12_SHIFT 22 +#define UTMI_TX_TXVDD12_MASK (0x3 << 22) + +#define UTMI_TX_CK60_PHSEL_SHIFT 17 +#define UTMI_TX_CK60_PHSEL_MASK (0xf << 17) + +#define UTMI_TX_IMPCAL_VTH_SHIFT 14 +#define UTMI_TX_IMPCAL_VTH_MASK (0x7 << 14) + +#define REG_RCAL_START (0x1 << 12) + +#define UTMI_TX_LOW_VDD_EN_SHIFT 11 + +#define UTMI_TX_AMP_SHIFT 0 +#define UTMI_TX_AMP_MASK (0x7 << 0) + +/* For UTMI_RX Register */ +#define UTMI_REG_SQ_LENGTH_SHIFT 15 +#define UTMI_REG_SQ_LENGTH_MASK (0x3 << 15) +
drivers/usb/phy/mv_usb2_phy.c line 130
Quoted 10 lines
drivers/usb/phy/mv_usb2_phy.c new file +10
-0+#define UTMI_RX_SQ_THRESH_SHIFT 4 +#define UTMI_RX_SQ_THRESH_MASK (0xf << 4) + +#define UTMI_OTG_ADDON_OTG_ON (1 << 0) + +enum mv_usb2_phy_type { +PXA168_USB , +PXA910_USB , +MMP2_USB , +};
Is this enum being used somewhere?
Quoted 5 lines
drivers/usb/phy/mv_usb2_phy.c new file +5
-0+ +static unsigned int u2o_get (void __iomem *base,unsigned int offset) +{ +return readl (base + offset); +}
drivers/usb/phy/mv_usb2_phy.c line 145
Quoted 10 lines
drivers/usb/phy/mv_usb2_phy.c new file +10
-0+ +static void u2o_set (void __iomem *base,unsigned int offset, +unsigned int value) +{ +u32 reg; + + reg =readl (base + offset); + reg |= value; +writel (reg, base + offset); +readl (base + offset);
spurious readl.
drivers/usb/phy/mv_usb2_phy.c line 156
Quoted 11 lines
drivers/usb/phy/mv_usb2_phy.c new file +11
-0+} + +static void u2o_clear (void __iomem *base,unsigned int offset, +unsigned int value) +{ +u32 reg; + + reg =readl (base + offset); + reg &= ~value; +writel (reg, base + offset); +readl (base + offset);
ditto..
drivers/usb/phy/mv_usb2_phy.c line 163
Quoted 7 lines
drivers/usb/phy/mv_usb2_phy.c new file +7
-0+} + +static void u2o_write (void __iomem *base,unsigned int offset, +unsigned int value) +{ +writel (value, base + offset); +readl (base + offset);
ditto..
Quoted 113 lines
drivers/usb/phy/mv_usb2_phy.c new file +113
-0+} + +static int _mv_usb2_phy_init (struct mv_usb2_phy *mv_phy) +{ +struct platform_device *pdev = mv_phy->pdev; +unsigned int loops =0 ; +void __iomem *base = mv_phy->base; + +dev_dbg (&pdev->dev,"phy init\n" ); + +/* Initialize the USB PHY power */ +if (mv_phy->type ==PXA910_USB ) { +u2o_set (base,UTMI_CTRL , (1 <<UTMI_CTRL_INPKT_DELAY_SOF_SHIFT ) + | (1 <<UTMI_CTRL_PU_REF_SHIFT )); + } + +u2o_set (base,UTMI_CTRL ,1 <<UTMI_CTRL_PLL_PWR_UP_SHIFT ); +u2o_set (base,UTMI_CTRL ,1 <<UTMI_CTRL_PWR_UP_SHIFT ); + +/* UTMI_PLL settings */ +u2o_clear (base,UTMI_PLL ,UTMI_PLL_PLLVDD18_MASK + |UTMI_PLL_PLLVDD12_MASK |UTMI_PLL_PLLCALI12_MASK + |UTMI_PLL_FBDIV_MASK |UTMI_PLL_REFDIV_MASK + |UTMI_PLL_ICP_MASK |UTMI_PLL_KVCO_MASK ); + +u2o_set (base,UTMI_PLL ,0xee <<UTMI_PLL_FBDIV_SHIFT + |0xb <<UTMI_PLL_REFDIV_SHIFT |3 <<UTMI_PLL_PLLVDD18_SHIFT + |3 <<UTMI_PLL_PLLVDD12_SHIFT |3 <<UTMI_PLL_PLLCALI12_SHIFT + |1 <<UTMI_PLL_ICP_SHIFT |3 <<UTMI_PLL_KVCO_SHIFT ); + +/* UTMI_TX */ +u2o_clear (base,UTMI_TX ,UTMI_TX_REG_EXT_FS_RCAL_EN_MASK + |UTMI_TX_TXVDD12_MASK |UTMI_TX_CK60_PHSEL_MASK + |UTMI_TX_IMPCAL_VTH_MASK |UTMI_TX_REG_EXT_FS_RCAL_MASK + |UTMI_TX_AMP_MASK ); +u2o_set (base,UTMI_TX ,3 <<UTMI_TX_TXVDD12_SHIFT + |4 <<UTMI_TX_CK60_PHSEL_SHIFT |4 <<UTMI_TX_IMPCAL_VTH_SHIFT + |8 <<UTMI_TX_REG_EXT_FS_RCAL_SHIFT |3 <<UTMI_TX_AMP_SHIFT ); + +/* UTMI_RX */ +u2o_clear (base,UTMI_RX ,UTMI_RX_SQ_THRESH_MASK + |UTMI_REG_SQ_LENGTH_MASK ); +u2o_set (base,UTMI_RX ,7 <<UTMI_RX_SQ_THRESH_SHIFT + |2 <<UTMI_REG_SQ_LENGTH_SHIFT ); + +/* UTMI_IVREF */ +if (mv_phy->type ==PXA168_USB ) +/* fixing Microsoft Altair board interface with NEC hub issue - +* Set UTMI_IVREF from 0x4a3 to 0x4bf */ +u2o_write (base,UTMI_IVREF ,0x4bf ); + +/* toggle VCOCAL_START bit of UTMI_PLL */ +udelay (200 ); +u2o_set (base,UTMI_PLL ,VCOCAL_START ); +udelay (40 ); +u2o_clear (base,UTMI_PLL ,VCOCAL_START ); + +/* toggle REG_RCAL_START bit of UTMI_TX */ +udelay (400 ); +u2o_set (base,UTMI_TX ,REG_RCAL_START ); +udelay (40 ); +u2o_clear (base,UTMI_TX ,REG_RCAL_START ); +udelay (400 ); + +/* Make sure PHY PLL is ready */ + loops =0 ; +while ((u2o_get (base,UTMI_PLL ) &PLL_READY ) ==0 ) { +mdelay (1 ); + loops++; +if (loops >100 ) { +dev_warn (&pdev->dev,"calibrate timeout, UTMI_PLL %x\n" , +u2o_get (base,UTMI_PLL )); +break ; + } + } + +if (mv_phy->type ==PXA168_USB ) { +u2o_set (base,UTMI_RESERVE ,1 <<5 ); +/* Turn on UTMI PHY OTG extension */ +u2o_write (base,UTMI_OTG_ADDON ,1 ); + } + +return 0 ; +} + +static int _mv_usb2_phy_shutdown (struct mv_usb2_phy *mv_phy) +{ +void __iomem *base = mv_phy->base; + +if (mv_phy->type ==PXA168_USB ) +u2o_clear (base,UTMI_OTG_ADDON ,UTMI_OTG_ADDON_OTG_ON ); + +u2o_clear (base,UTMI_CTRL ,UTMI_CTRL_RXBUF_PDWN ); +u2o_clear (base,UTMI_CTRL ,UTMI_CTRL_TXBUF_PDWN ); +u2o_clear (base,UTMI_CTRL ,UTMI_CTRL_USB_CLK_EN ); +u2o_clear (base,UTMI_CTRL ,1 <<UTMI_CTRL_PWR_UP_SHIFT ); +u2o_clear (base,UTMI_CTRL ,1 <<UTMI_CTRL_PLL_PWR_UP_SHIFT ); + +return 0 ; +} + +static int mv_usb2_phy_init (struct usb_phy *phy) +{ + struct mv_usb2_phy *mv_phy = container_of(phy, struct mv_usb2_phy, phy); +int i =0 ; + +mutex_lock (&mv_phy->phy_lock); +if (mv_phy->refcount++ ==0 ) { +for (i =0 ; i < mv_phy->clks_num; i++) +clk_prepare_enable (mv_phy->clks[i]); +_mv_usb2_phy_init (mv_phy); + } +mutex_unlock (&mv_phy->phy_lock);
drivers/usb/phy/mv_usb2_phy.c line 286
Quoted 10 lines
drivers/usb/phy/mv_usb2_phy.c new file +10
-0+return 0 ; +} + +static void mv_usb2_phy_shutdown (struct usb_phy *phy) +{ + struct mv_usb2_phy *mv_phy = container_of(phy, struct mv_usb2_phy, phy); +int i =0 ; + +mutex_lock (&mv_phy->phy_lock); +if (mv_phy->refcount++ ==0 ) {
shouldn't this be --mv_phy->refcount == 0?
Quoted 60 lines
drivers/usb/phy/mv_usb2_phy.c new file +60
-0+_mv_usb2_phy_shutdown (mv_phy); +for (i =0 ; i < mv_phy->clks_num; i++) +clk_disable_unprepare (mv_phy->clks[i]); + } +mutex_unlock (&mv_phy->phy_lock); +} + +static int mv_usb2_phy_probe (struct platform_device *pdev) +{ +struct mv_usb2_phy *mv_phy; +struct resource *r; +int i; +struct mv_usb_phy_platform_data *pdata; +const struct platform_device_id *id; + + mv_phy =devm_kzalloc (&pdev->dev,sizeof (*mv_phy),GFP_KERNEL ); +if (mv_phy ==NULL ) { +dev_err (&pdev->dev,"failed to allocate memory\n" ); +return -ENOMEM ; + } +mutex_init (&mv_phy->phy_lock); + + pdata = pdev->dev.platform_data; + id =platform_get_device_id (pdev); + +if (pdata ==NULL || id ==NULL ) { +dev_err (&pdev->dev, +"missing platform_data or id_entry\n" ); +return -ENODEV ; + } + mv_phy->type = (unsigned int )(id->driver_data); + mv_phy->clks_num = pdata->clknum; + mv_phy->clks =devm_kzalloc (&pdev->dev, +sizeof (struct clk *) * mv_phy->clks_num,GFP_KERNEL ); +if (mv_phy->clks ==NULL ) { +dev_err (&pdev->dev, +"failed to allocate mempory for clocks" ); +return -ENOMEM ; + } +for (i =0 ; i < mv_phy->clks_num; i++) { + mv_phy->clks[i] =devm_clk_get (&pdev->dev, + pdata->clkname[i]); +if (IS_ERR (mv_phy->clks[i])) { +dev_err (&pdev->dev,"failed to get clock %s\n" , + pdata->clkname[i]); +return PTR_ERR (mv_phy->clks[i]); + } + } + r =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); +if (r ==NULL ) { +dev_err (&pdev->dev,"no phy I/O memory resource defined\n" ); +return -ENODEV ; + } + mv_phy->base =devm_ioremap (&pdev->dev, r->start,resource_size (r)); +if (mv_phy->base ==NULL ) { +dev_err (&pdev->dev,"error map register base\n" ); +return -EBUSY ; + } + + mv_phy->phy.dev = &pdev->dev;
drivers/usb/phy/mv_usb2_phy.c line 356
Quoted 10 lines
drivers/usb/phy/mv_usb2_phy.c new file +10
-0+ mv_phy->phy.label ="mv-usb2" ; + mv_phy->phy.type =USB_PHY_TYPE_USB2 ; + mv_phy->phy.init = mv_usb2_phy_init; + mv_phy->phy.shutdown = mv_usb2_phy_shutdown; + +usb_add_phy_dev (&mv_phy->phy); + +platform_set_drvdata (pdev, mv_phy); + +dev_info (&pdev->dev,"mv usb2 phy initialized\n" );
dev_info makes the boot log noisy.
Quoted 62 lines
drivers/usb/phy/mv_usb2_phy.c new file +36
-0+ +return 0 ; +} + +static int mv_usb2_phy_remove (struct platform_device *pdev) +{ +struct mv_usb2_phy *mv_phy =platform_get_drvdata (pdev); + +usb_remove_phy (&mv_phy->phy); + +platform_set_drvdata (pdev,NULL ); + +return 0 ; +} + +static struct platform_device_id mv_usb2_phy_ids[] = { + { .name ="pxa168-usb-phy" , .driver_data =PXA168_USB }, + { .name ="pxa910-usb-phy" , .driver_data =PXA910_USB }, + { .name ="mmp2-usb-phy" , .driver_data =MMP2_USB }, + {} +}; + +static struct platform_driver mv_usb2_phy_driver = { + .probe = mv_usb2_phy_probe, + .remove = mv_usb2_phy_remove, + .driver = { + .name ="pxa168-usb-phy" , + }, + .id_table = mv_usb2_phy_ids, +}; + +static int __init mv_usb2_phy_driver_init (void ) +{ +return platform_driver_register (&mv_usb2_phy_driver); +} +arch_initcall (mv_usb2_phy_driver_init);include/linux/platform_data/mv_usb.h +6
-3@@ -47,9 +47,12 @@ struct mv_usb_platform_data {/* Force a_bus_req to be asserted */ unsigned int otg_force_a_bus_req:1; -int (*phy_init)(void __iomem *regbase); -void (*phy_deinit)(void __iomem *regbase); int (*set_vbus)(unsigned int vbus); - int (*private_init)(void __iomem *opregs, void __iomem *phyregs); }; + +struct mv_usb_phy_platform_data { +unsigned int clknum; +char **clkname; +}; +#endif include/linux/usb/mv_usb2.h new file +0
-0
include/linux/usb/mv_usb2.h line 2
Quoted 2 lines
include/linux/usb/mv_usb2.h new file +2
-0@@ -0,0 +1,40 @@ +/* +* Copyright (C) 2012 Marvell Inc.
why is this different from drivers/usb/phy/mv_usb2_phy.c?
Quoted 26 lines
include/linux/usb/mv_usb2.h new file +26
-0+* +* This software is licensed under the terms of the GNU General Public +* License version 2, as published by the Free Software Foundation, and +* may be copied, distributed, and modified under those terms. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +*/ + +#ifndef __MV_USB2_H +#define __MV_USB2_H + +#define MV_USB2_PHY_INDEX 0 +#define MV_USB2_OTG_PHY_INDEX 1 + +struct mv_usb2_phy { + struct usb_phy phy; + struct platform_device *pdev; + struct mutex phy_lock; + unsigned int refcount; + unsigned int type; + void __iomem *base; + struct clk **clks;
include/linux/usb/mv_usb2.h line 38
Quoted 10 lines
include/linux/usb/mv_usb2.h new file +10
-0+unsigned int clks_num; +}; + +#if defined(CONFIG_MV_USB2_PHY ) || defined(CONFIG_MV_USB2_PHY_MODULE ) + + +#else + + +#endif
This should be removed.
Thanks
Kishon
PATCH v7 1/16 usb: phy: mv_usb2: add PHY driver for marvell usb2 controller
Quoted 5 lines · kishon
Hi,
Quoted 1 line · Chao Xie
Quoted 15 lines
drivers/usb/phy/mv_usb2_phy.c line 130
Quoted 11 lines
The PHY is seperated from usb controller.
The usb controller used in marvell pxa168/pxa910/mmp2 are same,
...drivers/usb/phy/mv_usb2_phy.c new file +8
-0+ +#define UTMI_OTG_ADDON_OTG_ON (1 << 0) + +enum mv_usb2_phy_type { +PXA168_USB , +PXA910_USB , +MMP2_USB , +};Is this enum being used somewhere?
Yes, the PHY setting has a little difference between these SOCes. I have to use these types to track which SOC is used.
Quoted 11 lines
Quoted 11 lines
drivers/usb/phy/mv_usb2_phy.c new file +10
-0+ +static unsigned int u2o_get (void __iomem *base,unsigned int offset) +{ +return readl (base + offset); +} + +static void u2o_set (void __iomem *base,unsigned int offset, +unsigned int value) +{ +u32 reg;
Quoted 9 lines
drivers/usb/phy/mv_usb2_phy.c line 145
Quoted 5 lines
drivers/usb/phy/mv_usb2_phy.c new file +5
-0+ + reg =readl (base + offset); + reg |= value; +writel (reg, base + offset); +readl (base + offset);spurious readl.
Writing to the PHY setting registers has to make sure that every writing has been issued already.
The design engineer suggest us to add reading after the writing. It can make sure the writing has
taken effect.
Quoted 6 lines
Quoted 6 lines
drivers/usb/phy/mv_usb2_phy.c new file +6
-0+} + +static void u2o_clear (void __iomem *base,unsigned int offset, +unsigned int value) +{ +u32 reg;
Quoted 9 lines
drivers/usb/phy/mv_usb2_phy.c line 156
Quoted 5 lines
drivers/usb/phy/mv_usb2_phy.c new file +5
-0+ + reg =readl (base + offset); + reg &= ~value; +writel (reg, base + offset); +readl (base + offset);ditto..
Same reason. The clear is a writing operation
Quoted 11 lines
drivers/usb/phy/mv_usb2_phy.c line 163
Quoted 7 lines
drivers/usb/phy/mv_usb2_phy.c new file +7
-0+} + +static void u2o_write (void __iomem *base,unsigned int offset, +unsigned int value) +{ +writel (value, base + offset); +readl (base + offset);ditto..
Same reason.
Quoted 18 lines
Quoted 17 lines
drivers/usb/phy/mv_usb2_phy.c new file +13
-0+} + +static int _mv_usb2_phy_init (struct mv_usb2_phy *mv_phy) +{ +struct platform_device *pdev = mv_phy->pdev; +unsigned int loops =0 ; +void __iomem *base = mv_phy->base; + +dev_dbg (&pdev->dev,"phy init\n" ); + +/* Initialize the USB PHY power */ +if (mv_phy->type ==PXA910_USB ) { + u2o_set(base, UTMI_CTRL,(1<<UTMI_CTRL_INPKT_DELAY_SOF_SHIFT)
drivers/usb/phy/mv_usb2_phy.c new file +3
-0+ | (1<<UTMI_CTRL_PU_REF_SHIFT)); + } +
Quoted 13 lines
drivers/usb/phy/mv_usb2_phy.c line 271
Quoted 9 lines
4<<UTMI_TX_IMPCAL_VTH_SHIFT
+ | 8<<UTMI_TX_REG_EXT_FS_RCAL_SHIFT |
3<<UTMI_TX_AMP_SHIFT);
+
phy);drivers/usb/phy/mv_usb2_phy.c new file +4
-0+int i =0 ; + +mutex_lock (&mv_phy->phy_lock); +if (mv_phy->refcount++ ==0 ) {shouldn't this be --mv_phy->refcount == 0?
you are right.
Quoted 14 lines
drivers/usb/phy/mv_usb2_phy.c line 356
Quoted 10 lines
drivers/usb/phy/mv_usb2_phy.c new file +9
-0+_mv_usb2_phy_shutdown (mv_phy); +for (i =0 ; i < mv_phy->clks_num; i++) +clk_disable_unprepare (mv_phy->clks[i]); + } +usb_add_phy_dev (&mv_phy->phy); + +platform_set_drvdata (pdev, mv_phy); + +dev_info (&pdev->dev,"mv usb2 phy initialized\n" );
dev_infomakes the boot log noisy.
It is the only print in boot log for usb phy.
I can change it to be dev_dbg.
Quoted 17 lines
Quoted 17 lines
drivers/usb/phy/mv_usb2_phy.c new file +13
-0+ + return 0; +} + +static int mv_usb2_phy_remove (struct platform_device *pdev) +{ +struct mv_usb2_phy *mv_phy =platform_get_drvdata (pdev); + +struct mv_usb_phy_platform_data { +unsigned int clknum; +char **clkname; +}; +#endif include/linux/usb/mv_usb2.h new file +0
-0
Quoted 9 lines
include/linux/usb/mv_usb2.h line 2
Quoted 5 lines
include/linux/usb/mv_usb2.h new file +2
-0@@ -0,0 +1,40 @@ +/* +* Copyright (C) 2012 Marvell Inc. why is this different from
drivers/usb/phy/mv_usb2_phy.c?
The license has some misaligned. I will modify it.
Quoted 30 lines
Quoted 30 lines
include/linux/usb/mv_usb2.h new file +30
-0+* +* This software is licensed under the terms of the GNU General Public +* License version 2, as published by the Free Software Foundation, and +* may be copied, distributed, and modified under those terms. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +*/ + +#ifndef __MV_USB2_H +#define __MV_USB2_H + +#define MV_USB2_PHY_INDEX 0 +#define MV_USB2_OTG_PHY_INDEX 1 + +struct mv_usb2_phy { +struct usb_phy phy; +struct platform_device *pdev; +struct mutex phy_lock; +unsigned int refcount; +unsigned int type; +void __iomem *base; +struct clk **clks; +unsigned int clks_num; +}; + +#if defined(CONFIG_MV_USB2_PHY ) || defined(CONFIG_MV_USB2_PHY_MODULE )
Quoted 9 lines
include/linux/usb/mv_usb2.h line 38
Quoted 6 lines
include/linux/usb/mv_usb2.h new file +6
-0+ + +#else + + +#endif This should be removed.
You are right.
Quoted 2 lines
Thanks
Kishon
PATCH v7 1/16 usb: phy: mv_usb2: add PHY driver for marvell usb2 controller
Hi,
Quoted 18 lines · Chao Xie
Quoted 9 lines
Quoted 9 lines
drivers/usb/phy/mv_usb2_phy.c new file +9
-0+static unsigned int u2o_get (void __iomem *base,unsigned int offset) +{ +return readl (base + offset); +} + +static void u2o_set (void __iomem *base,unsigned int offset, +unsigned int value) +{ +u32 reg;Quoted 9 lines
drivers/usb/phy/mv_usb2_phy.c line 145
Quoted 5 lines
drivers/usb/phy/mv_usb2_phy.c new file +5
-0+ + reg =readl (base + offset); + reg |= value; +writel (reg, base + offset); +readl (base + offset);spurious readl.
Quoted 5 lines
Writing to the PHY setting registers has to make sure that every writing has been issued already.
The design engineer suggest us to add reading after the writing. It can make sure the writing has
taken effect.
add a comment explaining that, then.
Quoted 13 lines
Quoted 4 lines
Quoted 4 lines
drivers/usb/phy/mv_usb2_phy.c new file +4
-0+_mv_usb2_phy_shutdown (mv_phy); +for (i =0 ; i < mv_phy->clks_num; i++) +clk_disable_unprepare (mv_phy->clks[i]); + }Quoted 9 lines
drivers/usb/phy/mv_usb2_phy.c line 356
Quoted 5 lines
drivers/usb/phy/mv_usb2_phy.c new file +5
-0+usb_add_phy_dev (&mv_phy->phy); + +platform_set_drvdata (pdev, mv_phy); + +dev_info (&pdev->dev,"mv usb2 phy initialized\n" );
dev_infomakes the boot log noisy.
Quoted 2 lines
It is the only print in boot log for usb phy.
I can change it to bedev_dbg.
you can manage completely without it.
Signature · 8 lines
balbi -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20130218/bc2d6fad/attachment.sig>
PATCH v7 2/16 usb: gadget: mv_udc: use PHY driver for udc
In reply to Chao XieOriginaly, udc driver will call the callbacks in platform data for PHY initialization and shut down.
With PHY driver, it will call the APIs provided by PHY driver for PHY initialization and shut down. It removes the callbacks in platform data, and at same time it removes one block in the way of enabling device tree for udc driver.
--- drivers/usb/gadget/mv_udc.h | 2 +- drivers/usb/gadget/mv_udc_core.c | 37 +++++++++++++++---------------------- 2 files changed, 16 insertions(+), 23 deletions(-)
drivers/usb/gadget/mv_udc.h +1 -1
@@ -180,7 +180,6 @@ struct mv_udc {struct mv_cap_regs __iomem *cap_regs;struct mv_op_regs __iomem *op_regs; -void __iomem *phy_regs;unsigned int max_eps;struct mv_dqh *ep_dqh;size_t ep_dqh_size;
@@ -217,6 +216,7 @@ struct mv_udc {struct work_struct vbus_work;struct workqueue_struct *qwork; +struct usb_phy *phy;struct usb_phy *transceiver;struct mv_usb_platform_data *pdata;
drivers/usb/gadget/mv_udc_core.c +15 -22
@@ -35,6 +35,7 @@#include <linux/platform_device.h> #include <linux/clk.h> #include <linux/platform_data/mv_usb.h> +#include <linux/usb/mv_usb2.h> #include <asm/unaligned.h> #include "mv_udc.h"
@@ -1121,15 +1122,14 @@ static int mv_udc_enable_internal(struct mv_udc *udc)dev_dbg (&udc->dev->dev,"enable udc\n" );udc_clock_enable (udc); -if (udc->pdata->phy_init) { - retval = udc->pdata->phy_init (udc->phy_regs); -if (retval) { -dev_err (&udc->dev->dev, -"init phy error %d\n" , retval); -udc_clock_disable (udc); -return retval; - } + retval =usb_phy_init (udc->phy); +if (retval) { +dev_err (&udc->dev->dev, +"init phy error %d\n" , retval); +udc_clock_disable (udc); +return retval; } + udc->active =1 ;return 0 ;
@@ -1147,8 +1147,7 @@ static void mv_udc_disable_internal(struct mv_udc *udc) {if (udc->active) {dev_dbg (&udc->dev->dev,"disable udc\n" ); -if (udc->pdata->phy_deinit) - udc->pdata->phy_deinit (udc->phy_regs); +usb_phy_shutdown (udc->phy);udc_clock_disable (udc); udc->active =0 ; }
@@ -2175,8 +2174,8 @@ static int mv_udc_probe(struct platform_device *pdev)#ifdef CONFIG_USB_OTG_UTILS if (pdata->mode ==MV_USB_MODE_OTG ) { - udc->transceiver =devm_usb_get_phy (&pdev->dev, -USB_PHY_TYPE_USB2 ); + udc->transceiver =devm_usb_get_phy_dev (&pdev->dev, +MV_USB2_OTG_PHY_INDEX );if (IS_ERR_OR_NULL (udc->transceiver)) { udc->transceiver =NULL ;return -ENODEV ;
@@ -2194,7 +2193,7 @@ static int mv_udc_probe(struct platform_device *pdev) } } - r =platform_get_resource_byname (udc->dev,IORESOURCE_MEM ,"capregs" ); + r =platform_get_resource (udc->dev,IORESOURCE_MEM ,0 );if (r ==NULL ) {dev_err (&pdev->dev,"no I/O memory resource defined\n" );return -ENODEV ;
@@ -2207,18 +2206,12 @@ static int mv_udc_probe(struct platform_device *pdev)return -EBUSY ; } - r =platform_get_resource_byname (udc->dev,IORESOURCE_MEM ,"phyregs" ); -if (r ==NULL ) { -dev_err (&pdev->dev,"no phy I/O memory resource defined\n" ); + udc->phy =devm_usb_get_phy_dev (&pdev->dev,MV_USB2_PHY_INDEX ); +if (IS_ERR_OR_NULL (udc->phy)) { + udc->phy =NULL ;return -ENODEV ; } - udc->phy_regs =ioremap (r->start,resource_size (r)); -if (udc->phy_regs ==NULL ) { -dev_err (&pdev->dev,"failed to map phy I/O memory\n" ); -return -EBUSY ; - } -/* we will acces controller register, so enable the clk */ retval =mv_udc_enable_internal (udc);if (retval)
Signature · 1 line
1.7.4.1
PATCH v7 2/16 usb: gadget: mv_udc: use PHY driver for udc
Hi,
Quoted 99 lines · Chao Xie
Originaly, udc driver will call the callbacks in platform data for PHY initialization and shut down.
With PHY driver, it will call the APIs provided by PHY driver for PHY initialization and shut down. It removes the callbacks in platform data, and at same time it removes one block in the way of enabling device tree for udc driver.Signed-off-by Chao Xie <[email protected]>--- drivers/usb/gadget/mv_udc.h | 2 +- drivers/usb/gadget/mv_udc_core.c | 37 +++++++++++++++---------------------- 2 files changed, 16 insertions(+), 23 deletions(-)drivers/usb/gadget/mv_udc.h +1
-1@@ -180,7 +180,6 @@ struct mv_udc {struct mv_cap_regs __iomem *cap_regs;struct mv_op_regs __iomem *op_regs; -void __iomem *phy_regs;unsigned int max_eps;struct mv_dqh *ep_dqh;size_t ep_dqh_size;@@ -217,6 +216,7 @@ struct mv_udc {struct work_struct vbus_work;struct workqueue_struct *qwork; +struct usb_phy *phy;struct usb_phy *transceiver;struct mv_usb_platform_data *pdata;drivers/usb/gadget/mv_udc_core.c +12
-13@@ -35,6 +35,7 @@#include <linux/platform_device.h> #include <linux/clk.h> #include <linux/platform_data/mv_usb.h> +#include <linux/usb/mv_usb2.h> #include <asm/unaligned.h> #include "mv_udc.h" @@ -1121,15 +1122,14 @@ static int mv_udc_enable_internal(struct mv_udc *udc)dev_dbg (&udc->dev->dev,"enable udc\n" );udc_clock_enable (udc); -if (udc->pdata->phy_init) { - retval = udc->pdata->phy_init (udc->phy_regs); -if (retval) { -dev_err (&udc->dev->dev, -"init phy error %d\n" , retval); -udc_clock_disable (udc); -return retval; - } + retval =usb_phy_init (udc->phy); +if (retval) { +dev_err (&udc->dev->dev, +"init phy error %d\n" , retval); +udc_clock_disable (udc); +return retval; } + udc->active =1 ;return 0 ;@@ -1147,8 +1147,7 @@ static void mv_udc_disable_internal(struct mv_udc *udc) {if (udc->active) {dev_dbg (&udc->dev->dev,"disable udc\n" ); -if (udc->pdata->phy_deinit) - udc->pdata->phy_deinit (udc->phy_regs); +usb_phy_shutdown (udc->phy);udc_clock_disable (udc); udc->active =0 ; }@@ -2175,8 +2174,8 @@ static int mv_udc_probe(struct platform_device *pdev)#ifdef CONFIG_USB_OTG_UTILS if (pdata->mode ==MV_USB_MODE_OTG ) { - udc->transceiver =devm_usb_get_phy (&pdev->dev, -USB_PHY_TYPE_USB2 ); + udc->transceiver =devm_usb_get_phy_dev (&pdev->dev, +MV_USB2_OTG_PHY_INDEX );if (IS_ERR_OR_NULL (udc->transceiver)) { udc->transceiver =NULL ;return -ENODEV ;@@ -2194,7 +2193,7 @@ static int mv_udc_probe(struct platform_device *pdev) } } - r =platform_get_resource_byname (udc->dev,IORESOURCE_MEM ,"capregs" ); + r =platform_get_resource (udc->dev,IORESOURCE_MEM ,0 );if (r ==NULL ) {dev_err (&pdev->dev,"no I/O memory resource defined\n" );return -ENODEV ;
drivers/usb/gadget/mv_udc_core.c static int mv_udc_probe(struct platform_device *pdev) · line 2211
Quoted 9 lines
drivers/usb/gadget/mv_udc_core.c +3
-3@@ -2207,18 +2206,12 @@ static int mv_udc_probe(struct platform_device *pdev)return -EBUSY ; } - r =platform_get_resource_byname (udc->dev,IORESOURCE_MEM ,"phyregs" ); -if (r ==NULL ) { -dev_err (&pdev->dev,"no phy I/O memory resource defined\n" ); + udc->phy =devm_usb_get_phy_dev (&pdev->dev,MV_USB2_PHY_INDEX ); +if (IS_ERR_OR_NULL (udc->phy)) { + udc->phy =NULL ;
Ideally you shouldn't do this. Consider the case where devm_usb_get_phy_dev returns -EPROBE_DEFER. In that case you should return -EPROBE_DEFER from probe instead of manually writing the return value to -ENODEV.
This comment is applicable for the remaining patches that uses devm_usb_get_phy_dev.
Thanks
Kishon
PATCH v7 3/16 usb: ehci: ehci-mv: use PHY driver for ehci
In reply to Chao XieOriginaly, ehci driver will call the callbacks in platform data for PHY initialization and shut down.
With PHY driver, it will call the APIs provided by PHY driver for PHY initialization and shut down. It removes the callbacks in platform data, and at same time it removes one block in the way of enabling device tree for ehci driver.
--- drivers/usb/host/ehci-mv.c | 46 ++++++++++++++----------------------------- 1 files changed, 15 insertions(+), 31 deletions(-)
drivers/usb/host/ehci-mv.c +15 -31
@@ -15,17 +15,18 @@#include <linux/clk.h> #include <linux/err.h> #include <linux/usb/otg.h> +#include <linux/usb/mv_usb2.h> #include <linux/platform_data/mv_usb.h> #define CAPLENGTH_MASK (0xff)struct ehci_hcd_mv {struct usb_hcd *hcd; +struct usb_phy *phy;/* Which mode does this ehci running OTG/Host ? */ int mode; -void __iomem *phy_regs;void __iomem *cap_regs;void __iomem *op_regs;
@@ -56,22 +57,15 @@ static void ehci_clock_disable(struct ehci_hcd_mv *ehci_mv)static int mv_ehci_enable (struct ehci_hcd_mv *ehci_mv) { -int retval; -ehci_clock_enable (ehci_mv); -if (ehci_mv->pdata->phy_init) { - retval = ehci_mv->pdata->phy_init (ehci_mv->phy_regs); -if (retval) -return retval; - } -return 0 ; +return usb_phy_init (ehci_mv->phy); }static void mv_ehci_disable (struct ehci_hcd_mv *ehci_mv) { -if (ehci_mv->pdata->phy_deinit) - ehci_mv->pdata->phy_deinit (ehci_mv->phy_regs); +usb_phy_shutdown (ehci_mv->phy); +ehci_clock_disable (ehci_mv); }
@@ -184,22 +178,7 @@ static int mv_ehci_probe(struct platform_device *pdev) } } - r =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"phyregs" ); -if (r ==NULL ) { -dev_err (&pdev->dev,"no phy I/O memory resource defined\n" ); - retval = -ENODEV ; - goto err_clear_drvdata; - } - - ehci_mv->phy_regs =devm_ioremap (&pdev->dev, r->start, -resource_size (r)); -if (ehci_mv->phy_regs ==0 ) { -dev_err (&pdev->dev,"failed to map phy I/O memory\n" ); - retval = -EFAULT ; - goto err_clear_drvdata; - } - - r =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"capregs" ); + r =platform_get_resource (pdev,IORESOURCE_MEM ,0 );if (!r) {dev_err (&pdev->dev,"no I/O memory resource defined\n" ); retval = -ENODEV ;
@@ -214,6 +193,13 @@ static int mv_ehci_probe(struct platform_device *pdev) goto err_clear_drvdata; } + ehci_mv->phy =devm_usb_get_phy_dev (&pdev->dev,MV_USB2_PHY_INDEX ); +if (IS_ERR_OR_NULL (ehci_mv->phy)) { + ehci_mv->phy =NULL ; + retval = -ENODEV ; + goto err_clear_drvdata; + } + retval =mv_ehci_enable (ehci_mv);if (retval) {dev_err (&pdev->dev,"init phy error %d\n" , retval);
@@ -241,7 +227,8 @@ static int mv_ehci_probe(struct platform_device *pdev) ehci_mv->mode = pdata->mode;if (ehci_mv->mode ==MV_USB_MODE_OTG ) {#ifdef CONFIG_USB_OTG_UTILS - ehci_mv->otg =devm_usb_get_phy (&pdev->dev,USB_PHY_TYPE_USB2 ); + ehci_mv->otg =devm_usb_get_phy_dev (&pdev->dev, +MV_USB2_OTG_PHY_INDEX );if (IS_ERR_OR_NULL (ehci_mv->otg)) {dev_err (&pdev->dev,"unable to find transceiver\n" );
@@ -275,9 +262,6 @@ static int mv_ehci_probe(struct platform_device *pdev) } } -if (pdata->private_init) - pdata->private_init (ehci_mv->op_regs, ehci_mv->phy_regs); - dev_info(&pdev->dev, "successful find EHCI device with regs 0x%p irq %d" " working in %s mode\n", hcd->regs, hcd->irq,
Signature · 1 line
1.7.4.1
PATCH v7 4/16 usb: otg: mv_otg: use PHY driver for otg
In reply to Chao XieOriginaly, otg driver will call the callbacks in platform data for PHY initialization and shut down.
With PHY driver, it will call the APIs provided by PHY driver for PHY initialization and shut down. It removes the callbacks in platform data, and at same time it removes one block in the way of enabling device tree for otg driver.
--- drivers/usb/otg/mv_otg.c | 51 ++++++++++++++++++---------------------------- drivers/usb/otg/mv_otg.h | 2 +- 2 files changed, 21 insertions(+), 32 deletions(-)
drivers/usb/otg/mv_otg.c +20 -31
@@ -25,6 +25,7 @@#include <linux/usb/otg.h> #include <linux/usb/gadget.h> #include <linux/usb/hcd.h> +#include <linux/usb/mv_usb2.h> #include <linux/platform_data/mv_usb.h> #include "mv_otg.h"
@@ -261,14 +262,12 @@ static int mv_otg_enable_internal(struct mv_otg *mvotg)dev_dbg (&mvotg->pdev->dev,"otg enabled\n" );otg_clock_enable (mvotg); -if (mvotg->pdata->phy_init) { - retval = mvotg->pdata->phy_init (mvotg->phy_regs); -if (retval) { -dev_err (&mvotg->pdev->dev, -"init phy error %d\n" , retval); -otg_clock_disable (mvotg); -return retval; - } + retval =usb_phy_init (mvotg->outer_phy); +if (retval) { +dev_err (&mvotg->pdev->dev, +"init phy error %d\n" , retval); +otg_clock_disable (mvotg); +return retval; } mvotg->active =1 ;
@@ -288,8 +287,7 @@ static void mv_otg_disable_internal(struct mv_otg *mvotg) {if (mvotg->active) {dev_dbg (&mvotg->pdev->dev,"otg disabled\n" ); -if (mvotg->pdata->phy_deinit) - mvotg->pdata->phy_deinit (mvotg->phy_regs); +usb_phy_shutdown (mvotg->outer_phy);otg_clock_disable (mvotg); mvotg->active =0 ; }
@@ -672,7 +670,6 @@ int mv_otg_remove(struct platform_device *pdev)mv_otg_disable (mvotg); -usb_remove_phy (&mvotg->phy);platform_set_drvdata (pdev,NULL );return 0 ;
@@ -741,23 +738,8 @@ static int mv_otg_probe(struct platform_device *pdev)for (i =0 ; i <OTG_TIMER_NUM ; i++)init_timer (&mvotg->otg_ctrl.timer[i]); - r =platform_get_resource_byname (mvotg->pdev, -IORESOURCE_MEM ,"phyregs" ); -if (r ==NULL ) { -dev_err (&pdev->dev,"no phy I/O memory resource defined\n" ); - retval = -ENODEV ; - goto err_destroy_workqueue; - } - - mvotg->phy_regs =devm_ioremap (&pdev->dev, r->start,resource_size (r)); -if (mvotg->phy_regs ==NULL ) { -dev_err (&pdev->dev,"failed to map phy I/O memory\n" ); - retval = -EFAULT ; - goto err_destroy_workqueue; - } - - r =platform_get_resource_byname (mvotg->pdev, -IORESOURCE_MEM ,"capregs" ); + r =platform_get_resource (mvotg->pdev, +IORESOURCE_MEM ,0 );if (r ==NULL ) {dev_err (&pdev->dev,"no I/O memory resource defined\n" ); retval = -ENODEV ;
@@ -770,6 +752,13 @@ static int mv_otg_probe(struct platform_device *pdev) retval = -EFAULT ; goto err_destroy_workqueue; } + mvotg->outer_phy =devm_usb_get_phy_dev (&pdev->dev,0 ); +if (IS_ERR_OR_NULL (mvotg->outer_phy)) { + mvotg->outer_phy =NULL ; + retval = -ENODEV ; +dev_err (&pdev->dev,"can not find outer phy\n" ); + goto err_destroy_workqueue; + }/* we will acces controller register, so enable the udc controller */ retval =mv_otg_enable_internal (mvotg);
@@ -830,7 +819,7 @@ static int mv_otg_probe(struct platform_device *pdev) goto err_disable_clk; } - retval =usb_add_phy (&mvotg->phy,USB_PHY_TYPE_USB2 ); + retval =usb_add_phy_dev (&mvotg->phy);if (retval <0 ) {dev_err (&pdev->dev,"can't register transceiver, %d\n" , retval);
@@ -841,7 +830,7 @@ static int mv_otg_probe(struct platform_device *pdev)if (retval <0 ) {dev_dbg (&pdev->dev,"Can't register sysfs attr group: %d\n" , retval); - goto err_remove_phy; + goto err_remove_otg_phy; }spin_lock_init (&mvotg->wq_lock);
@@ -856,7 +845,7 @@ static int mv_otg_probe(struct platform_device *pdev)return 0 ; -err_remove_phy: +err_remove_otg_phy:usb_remove_phy (&mvotg->phy); err_disable_clk:mv_otg_disable_internal (mvotg);
drivers/usb/otg/mv_otg.h +1 -1
@@ -137,10 +137,10 @@ struct mv_otg_regs {struct mv_otg {struct usb_phy phy; +struct usb_phy *outer_phy;struct mv_otg_ctrl otg_ctrl;/* base address */ -void __iomem *phy_regs;void __iomem *cap_regs;struct mv_otg_regs __iomem *op_regs;
Signature · 1 line
1.7.4.1
PATCH v7 5/16 arm: mmp2: change the defintion of usb devices
In reply to Chao Xieadd the udc/otg/ehci devices for mmp2
--- arch/arm/mach-mmp/include/mach/mmp2.h | 4 ++++ arch/arm/mach-mmp/mmp2.c | 4 ++++ 2 files changed, 8 insertions(+), 0 deletions(-)
arch/arm/mach-mmp/include/mach/mmp2.h +4 -0
@@ -31,6 +31,10 @@ extern struct pxa_device_desc mmp2_device_sdh2;extern struct pxa_device_desc mmp2_device_sdh3;extern struct pxa_device_desc mmp2_device_asram;extern struct pxa_device_desc mmp2_device_isram; +extern struct pxa_device_desc mmp2_device_u2o; +extern struct pxa_device_desc mmp2_device_u2ootg; +extern struct pxa_device_desc mmp2_device_u2oehci; +extern struct pxa_device_desc mmp2_device_u2ophy;extern struct platform_device mmp2_device_gpio;
arch/arm/mach-mmp/mmp2.c +4 -0
@@ -153,6 +153,10 @@ MMP2_DEVICE(sdh3, "sdhci-pxav3", 3, MMC4, 0xd4281800, 0x120);MMP2_DEVICE (asram,"asram" ,-1 ,NONE ,0xe0000000 ,0x4000 );/* 0xd1000000 ~ 0xd101ffff is reserved for secure processor */ MMP2_DEVICE (isram,"isram" ,-1 ,NONE ,0xd1020000 ,0x18000 ); +MMP2_DEVICE (u2ophy,"mmp2-usb-phy" ,-1 ,NONE ,0xd4207000 ,0x1ff ); +MMP2_DEVICE (u2o,"mv-udc" ,-1 ,USB_OTG ,0xd4208100 ,0x1ff ); +MMP2_DEVICE (u2ootg,"mv-otg" ,-1 ,USB_OTG ,0xd4208100 ,0x1ff ); +MMP2_DEVICE (u2oehci,"mv-ehci" ,-1 ,USB_OTG ,0xd4208100 ,0x1ff );struct resource mmp2_resource_gpio[] = { {
Signature · 1 line
1.7.4.1
PATCH v7 6/16 arm: pxa910: change the defintion of usb devices
In reply to Chao Xiebecause phy is seperated from the usb controller driver, we can use the common pxa_device_desc for device register.
--- arch/arm/mach-mmp/include/mach/pxa910.h | 7 ++++--- arch/arm/mach-mmp/pxa910.c | 4 ++++ 2 files changed, 8 insertions(+), 3 deletions(-)
arch/arm/mach-mmp/include/mach/pxa910.h +4 -3
@@ -20,9 +20,10 @@ extern struct pxa_device_desc pxa910_device_pwm2;extern struct pxa_device_desc pxa910_device_pwm3;extern struct pxa_device_desc pxa910_device_pwm4;extern struct pxa_device_desc pxa910_device_nand; -extern struct platform_device pxa168_device_u2o; -extern struct platform_device pxa168_device_u2ootg; -extern struct platform_device pxa168_device_u2oehci; +extern struct pxa_device_desc pxa910_device_u2o; +extern struct pxa_device_desc pxa910_device_u2ootg; +extern struct pxa_device_desc pxa910_device_u2oehci; +extern struct pxa_device_desc pxa910_device_u2ophy;extern struct platform_device pxa910_device_gpio;extern struct platform_device pxa910_device_rtc;
arch/arm/mach-mmp/pxa910.c +4 -0
@@ -138,6 +138,10 @@ PXA910_DEVICE(pwm2, "pxa910-pwm", 1, NONE, 0xd401a400, 0x10);PXA910_DEVICE (pwm3,"pxa910-pwm" ,2 ,NONE ,0xd401a800 ,0x10 );PXA910_DEVICE (pwm4,"pxa910-pwm" ,3 ,NONE ,0xd401ac00 ,0x10 );PXA910_DEVICE (nand,"pxa3xx-nand" ,-1 ,NAND ,0xd4283000 ,0x80 ,97 ,99 ); +PXA910_DEVICE (u2ophy,"pxa910-usb-phy" ,-1 ,NONE ,0xd4207000 ,0x1ff ); +PXA910_DEVICE (u2o,"mv-udc" ,-1 ,USB1 ,0xd4208100 ,0x1ff ); +PXA910_DEVICE (u2ootg,"mv-otg" ,-1 ,USB1 ,0xd4208100 ,0x1ff ); +PXA910_DEVICE (u2oehci,"mv-ehci" ,-1 ,USB1 ,0xd4208100 ,0x1ff );struct resource pxa910_resource_gpio[] = { {
Signature · 1 line
1.7.4.1
PATCH v7 7/16 arm: brownstone: add usb support for the board
In reply to Chao Xiefor brownstone board, add the udc/otg/ehci support
--- arch/arm/mach-mmp/brownstone.c | 68 ++++++++++++++++++++++++++++++++++++++++ 1 files changed, 68 insertions(+), 0 deletions(-)
arch/arm/mach-mmp/brownstone.c +68 -0
@@ -18,6 +18,9 @@#include <linux/regulator/max8649.h> #include <linux/regulator/fixed.h> #include <linux/mfd/max8925.h> +#include <linux/usb/phy.h> +#include <linux/usb/mv_usb2.h> +#include <linux/platform_data/mv_usb.h> #include <asm/mach-types.h> #include <asm/mach/arch.h>
@@ -195,6 +198,31 @@ static struct sram_platdata mmp2_isram_platdata = { .granularity = SRAM_GRANULARITY, }; +#ifdef CONFIG_USB_SUPPORT + +static char *mmp2_usb_clock_name[] = { + [0 ] ="usb_clk" , +}; + +static struct mv_usb_phy_platform_data brownstone_usb_phy_pdata = { + .clknum =1 , + .clkname = mmp2_usb_clock_name, +}; + +#if defined(CONFIG_USB_MV_UDC ) || defined(CONFIG_USB_EHCI_MV_U2O ) + +static struct mv_usb_platform_data brownstone_usb_pdata = { + .clknum =1 , + .clkname = mmp2_usb_clock_name, + .vbus =NULL , + .mode =MV_USB_MODE_OTG , + .otg_force_a_bus_req =1 , + .set_vbus =NULL , +}; +#endif +#endif + +static void __init brownstone_init (void ) {mfp_config (ARRAY_AND_SIZE (brownstone_pin_config));
@@ -211,6 +239,46 @@ static void __init brownstone_init(void)/* enable 5v regulator */ platform_device_register (&brownstone_v_5vp_device); + +#ifdef CONFIG_USB_SUPPORT +pxa_register_device (&mmp2_device_u2ophy, &brownstone_usb_phy_pdata, +sizeof (brownstone_usb_phy_pdata)); +#endif + +#ifdef CONFIG_USB_MV_UDC +/* for usb2 phy */ +usb_bind_phy (mmp2_device_u2o.drv_name,MV_USB2_PHY_INDEX , + mmp2_device_u2ophy.drv_name); +#ifdef CONFIG_USB_MV_OTG +/* for usb2 otg phy */ +usb_bind_phy (mmp2_device_u2o.drv_name,MV_USB2_OTG_PHY_INDEX , + mmp2_device_u2ootg.drv_name); +#endif +pxa_register_device (&mmp2_device_u2o, &brownstone_usb_pdata, +sizeof (brownstone_usb_pdata)); +#endif + +#ifdef CONFIG_USB_EHCI_MV_U2O +/* for usb2 phy */ +usb_bind_phy (mmp2_device_u2oehci.dev_name,MV_USB2_PHY_INDEX , + mmp2_device_u2ophy.dev_name); +#ifdef CONFIG_USB_MV_OTG +/* for usb2 otg phy */ +usb_bind_phy (mmp2_device_u2oehci.drv_name,MV_USB2_OTG_PHY_INDEX , + mmp2_device_u2ootg.drv_name); +#endif +pxa_register_device (&mmp2_device_u2oehci, &brownstone_usb_pdata, +sizeof (brownstone_usb_pdata)); +#endif + +#ifdef CONFIG_USB_MV_OTG +/* for usb2 phy */ +usb_bind_phy (mmp2_device_u2ootg.dev_name,MV_USB2_PHY_INDEX , + mmp2_device_u2ophy.dev_name); +pxa_register_device (&mmp2_device_u2ootg, &brownstone_usb_pdata, +sizeof (brownstone_usb_pdata)); +#endif + }MACHINE_START (BROWNSTONE ,"Brownstone Development Platform" )
Signature · 1 line
1.7.4.1
PATCH v7 8/16 arm: ttc_dkb: add usb support
In reply to Chao Xiefor ttc_dkb board, add udc/otg/ehci support
--- arch/arm/mach-mmp/ttc_dkb.c | 50 +++++++++++++++++++++++++++++++++--------- 1 files changed, 39 insertions(+), 11 deletions(-)
arch/arm/mach-mmp/ttc_dkb.c +39 -11
@@ -18,6 +18,8 @@#include <linux/i2c/pca953x.h> #include <linux/gpio.h> #include <linux/mfd/88pm860x.h> +#include <linux/usb/phy.h> +#include <linux/usb/mv_usb2.h> #include <linux/platform_data/mv_usb.h> #include <asm/mach-types.h>
@@ -27,7 +29,6 @@#include <mach/mfp-pxa910.h> #include <mach/pxa910.h> #include <mach/irqs.h> -#include <mach/regs-usb.h> #include "common.h"
@@ -158,20 +159,24 @@ static struct i2c_board_info ttc_dkb_i2c_info[] = { };#ifdef CONFIG_USB_SUPPORT -#if defined(CONFIG_USB_MV_UDC ) || defined(CONFIG_USB_EHCI_MV_U2O )static char *pxa910_usb_clock_name[] = { - [0 ] ="U2OCLK" , + [0 ] ="usb_clk" , }; +static struct mv_usb_phy_platform_data ttc_usb_phy_pdata = { + .clknum =1 , + .clkname = pxa910_usb_clock_name, +}; + +#if defined(CONFIG_USB_MV_UDC ) || defined(CONFIG_USB_EHCI_MV_U2O ) +static struct mv_usb_platform_data ttc_usb_pdata = { .clknum =1 , .clkname = pxa910_usb_clock_name, .vbus =NULL , .mode =MV_USB_MODE_OTG , .otg_force_a_bus_req =1 , - .phy_init = pxa_usb_phy_init, - .phy_deinit = pxa_usb_phy_deinit, .set_vbus =NULL , };#endif
@@ -198,19 +203,42 @@ static void __init ttc_dkb_init(void)pxa910_add_twsi (0 ,NULL ,ARRAY_AND_SIZE (ttc_dkb_i2c_info));platform_add_devices (ARRAY_AND_SIZE (ttc_dkb_devices)); +#ifdef CONFIG_USB_SUPPORT +pxa_register_device (&pxa910_device_u2ophy, &ttc_usb_phy_pdata, +sizeof (ttc_usb_phy_pdata)); +#endif +#ifdef CONFIG_USB_MV_UDC - pxa168_device_u2o.dev.platform_data = &ttc_usb_pdata; -platform_device_register (&pxa168_device_u2o); +/* for usb2 phy */ +usb_bind_phy (pxa910_device_u2o.drv_name,MV_USB2_PHY_INDEX , + pxa910_device_u2ophy.drv_name); +#ifdef CONFIG_USB_MV_OTG +/* for usb2 otg phy */ +usb_bind_phy (pxa910_device_u2o.drv_name,MV_USB2_OTG_PHY_INDEX , + pxa910_device_u2ootg.drv_name); +#endif +pxa_register_device (&pxa910_device_u2o, &ttc_usb_pdata, +sizeof (ttc_usb_pdata));#endif #ifdef CONFIG_USB_EHCI_MV_U2O - pxa168_device_u2oehci.dev.platform_data = &ttc_usb_pdata; -platform_device_register (&pxa168_device_u2oehci); +/* for usb2 phy */ +usb_bind_phy (pxa910_device_u2oehci.drv_name,MV_USB2_PHY_INDEX , + pxa910_device_u2ophy.drv_name); +#ifdef CONFIG_USB_MV_OTG +/* for usb2 otg phy */ +usb_bind_phy (pxa910_device_u2oehci.drv_name,MV_USB2_OTG_PHY_INDEX , + pxa910_device_u2ootg.drv_name); +#endif +pxa_register_device (&pxa910_device_u2oehci, &ttc_usb_pdata, +sizeof (ttc_usb_pdata));#endif #ifdef CONFIG_USB_MV_OTG - pxa168_device_u2ootg.dev.platform_data = &ttc_usb_pdata; -platform_device_register (&pxa168_device_u2ootg); +usb_bind_phy (pxa910_device_u2ootg.drv_name,MV_USB2_PHY_INDEX , + pxa910_device_u2ophy.drv_name); +pxa_register_device (&pxa910_device_u2ootg, &ttc_usb_pdata, +sizeof (ttc_usb_pdata));#endif }
Signature · 1 line
1.7.4.1
PATCH v7 9/16 arm: mmp: remove the usb phy setting
In reply to Chao Xiephy setting are formatted into a phy driver at drivers/usb/phy, we do not need do the setting in SOC files.
--- arch/arm/mach-mmp/devices.c | 278 ----------------------------- arch/arm/mach-mmp/include/mach/regs-usb.h | 253 -------------------------- 2 files changed, 0 insertions(+), 531 deletions(-) delete mode 100644 arch/arm/mach-mmp/include/mach/regs-usb.h
arch/arm/mach-mmp/devices.c +0 -278
@@ -15,7 +15,6 @@#include <mach/irqs.h> #include <mach/devices.h> #include <mach/cputype.h> -#include <mach/regs-usb.h> int __init pxa_register_device (struct pxa_device_desc *desc,void *data,size_t size)
@@ -72,280 +71,3 @@ int __init pxa_register_device(struct pxa_device_desc *desc,return platform_device_add (pdev); } -#if defined(CONFIG_USB ) || defined(CONFIG_USB_GADGET ) - -/***************************************************************************** -* The registers read/write routines -*****************************************************************************/ - -static unsigned int u2o_get (void __iomem *base,unsigned int offset) -{ -return readl_relaxed (base + offset); -} - -static void u2o_set (void __iomem *base,unsigned int offset, -unsigned int value) -{ -u32 reg; - - reg =readl_relaxed (base + offset); - reg |= value; -writel_relaxed (reg, base + offset); -readl_relaxed (base + offset); -} - -static void u2o_clear (void __iomem *base,unsigned int offset, -unsigned int value) -{ -u32 reg; - - reg =readl_relaxed (base + offset); - reg &= ~value; -writel_relaxed (reg, base + offset); -readl_relaxed (base + offset); -} - -static void u2o_write (void __iomem *base,unsigned int offset, -unsigned int value) -{ -writel_relaxed (value, base + offset); -readl_relaxed (base + offset); -} - -#if defined(CONFIG_USB_MV_UDC ) || defined(CONFIG_USB_EHCI_MV ) - -#if defined(CONFIG_CPU_PXA910 ) || defined(CONFIG_CPU_PXA168 ) - -static DEFINE_MUTEX (phy_lock); -static int phy_init_cnt; - -static int usb_phy_init_internal (void __iomem *base) -{ -int loops; - -pr_info ("Init usb phy!!!\n" ); - -/* Initialize the USB PHY power */ -if (cpu_is_pxa910 ()) { -u2o_set (base,UTMI_CTRL , (1 <<UTMI_CTRL_INPKT_DELAY_SOF_SHIFT ) - | (1 <<UTMI_CTRL_PU_REF_SHIFT )); - } - -u2o_set (base,UTMI_CTRL ,1 <<UTMI_CTRL_PLL_PWR_UP_SHIFT ); -u2o_set (base,UTMI_CTRL ,1 <<UTMI_CTRL_PWR_UP_SHIFT ); - -/* UTMI_PLL settings */ -u2o_clear (base,UTMI_PLL ,UTMI_PLL_PLLVDD18_MASK - |UTMI_PLL_PLLVDD12_MASK |UTMI_PLL_PLLCALI12_MASK - |UTMI_PLL_FBDIV_MASK |UTMI_PLL_REFDIV_MASK - |UTMI_PLL_ICP_MASK |UTMI_PLL_KVCO_MASK ); - -u2o_set (base,UTMI_PLL ,0xee <<UTMI_PLL_FBDIV_SHIFT - |0xb <<UTMI_PLL_REFDIV_SHIFT |3 <<UTMI_PLL_PLLVDD18_SHIFT - |3 <<UTMI_PLL_PLLVDD12_SHIFT |3 <<UTMI_PLL_PLLCALI12_SHIFT - |1 <<UTMI_PLL_ICP_SHIFT |3 <<UTMI_PLL_KVCO_SHIFT ); - -/* UTMI_TX */ -u2o_clear (base,UTMI_TX ,UTMI_TX_REG_EXT_FS_RCAL_EN_MASK - |UTMI_TX_TXVDD12_MASK |UTMI_TX_CK60_PHSEL_MASK - |UTMI_TX_IMPCAL_VTH_MASK |UTMI_TX_REG_EXT_FS_RCAL_MASK - |UTMI_TX_AMP_MASK ); -u2o_set (base,UTMI_TX ,3 <<UTMI_TX_TXVDD12_SHIFT - |4 <<UTMI_TX_CK60_PHSEL_SHIFT |4 <<UTMI_TX_IMPCAL_VTH_SHIFT - |8 <<UTMI_TX_REG_EXT_FS_RCAL_SHIFT |3 <<UTMI_TX_AMP_SHIFT ); - -/* UTMI_RX */ -u2o_clear (base,UTMI_RX ,UTMI_RX_SQ_THRESH_MASK - |UTMI_REG_SQ_LENGTH_MASK ); -u2o_set (base,UTMI_RX ,7 <<UTMI_RX_SQ_THRESH_SHIFT - |2 <<UTMI_REG_SQ_LENGTH_SHIFT ); - -/* UTMI_IVREF */ -if (cpu_is_pxa168 ()) -/* fixing Microsoft Altair board interface with NEC hub issue - -* Set UTMI_IVREF from 0x4a3 to 0x4bf */ -u2o_write (base,UTMI_IVREF ,0x4bf ); - -/* toggle VCOCAL_START bit of UTMI_PLL */ -udelay (200 ); -u2o_set (base,UTMI_PLL ,VCOCAL_START ); -udelay (40 ); -u2o_clear (base,UTMI_PLL ,VCOCAL_START ); - -/* toggle REG_RCAL_START bit of UTMI_TX */ -udelay (400 ); -u2o_set (base,UTMI_TX ,REG_RCAL_START ); -udelay (40 ); -u2o_clear (base,UTMI_TX ,REG_RCAL_START ); -udelay (400 ); - -/* Make sure PHY PLL is ready */ - loops =0 ; -while ((u2o_get (base,UTMI_PLL ) &PLL_READY ) ==0 ) { -mdelay (1 ); - loops++; -if (loops >100 ) { -printk (KERN_WARNING "calibrate timeout, UTMI_PLL %x\n" , -u2o_get (base,UTMI_PLL )); -break ; - } - } - -if (cpu_is_pxa168 ()) { -u2o_set (base,UTMI_RESERVE ,1 <<5 ); -/* Turn on UTMI PHY OTG extension */ -u2o_write (base,UTMI_OTG_ADDON ,1 ); - } - -return 0 ; -} - -static int usb_phy_deinit_internal (void __iomem *base) -{ -pr_info ("Deinit usb phy!!!\n" ); - -if (cpu_is_pxa168 ()) -u2o_clear (base,UTMI_OTG_ADDON ,UTMI_OTG_ADDON_OTG_ON ); - -u2o_clear (base,UTMI_CTRL ,UTMI_CTRL_RXBUF_PDWN ); -u2o_clear (base,UTMI_CTRL ,UTMI_CTRL_TXBUF_PDWN ); -u2o_clear (base,UTMI_CTRL ,UTMI_CTRL_USB_CLK_EN ); -u2o_clear (base,UTMI_CTRL ,1 <<UTMI_CTRL_PWR_UP_SHIFT ); -u2o_clear (base,UTMI_CTRL ,1 <<UTMI_CTRL_PLL_PWR_UP_SHIFT ); - -return 0 ; -} - -int pxa_usb_phy_init (void __iomem *phy_reg) -{ -mutex_lock (&phy_lock); -if (phy_init_cnt++ ==0 ) -usb_phy_init_internal (phy_reg); -mutex_unlock (&phy_lock); -return 0 ; -} - -void pxa_usb_phy_deinit (void __iomem *phy_reg) -{ -WARN_ON (phy_init_cnt ==0 ); - -mutex_lock (&phy_lock); -if (--phy_init_cnt ==0 ) -usb_phy_deinit_internal (phy_reg); -mutex_unlock (&phy_lock); -} -#endif -#endif -#endif - -#ifdef CONFIG_USB_SUPPORT -static u64 usb_dma_mask = ~(u32 )0 ; - -#ifdef CONFIG_USB_MV_UDC -struct resource pxa168_u2o_resources[] = { -/* regbase */ - [0 ] = { - .start =PXA168_U2O_REGBASE + U2x_CAPREGS_OFFSET, - .end =PXA168_U2O_REGBASE +USB_REG_RANGE , - .flags =IORESOURCE_MEM , - .name ="capregs" , - }, -/* phybase */ - [1 ] = { - .start =PXA168_U2O_PHYBASE , - .end =PXA168_U2O_PHYBASE +USB_PHY_RANGE , - .flags =IORESOURCE_MEM , - .name ="phyregs" , - }, - [2 ] = { - .start =IRQ_PXA168_USB1 , - .end =IRQ_PXA168_USB1 , - .flags =IORESOURCE_IRQ , - }, -}; - -struct platform_device pxa168_device_u2o = { - .name ="mv-udc" , - .id =-1 , - .resource = pxa168_u2o_resources, - .num_resources =ARRAY_SIZE (pxa168_u2o_resources), - .dev = { - .dma_mask = &usb_dma_mask, - .coherent_dma_mask =0xffffffff , - } -}; -#endif /* CONFIG_USB_MV_UDC */ - -#ifdef CONFIG_USB_EHCI_MV_U2O -struct resource pxa168_u2oehci_resources[] = { -/* regbase */ - [0 ] = { - .start =PXA168_U2O_REGBASE + U2x_CAPREGS_OFFSET, - .end =PXA168_U2O_REGBASE +USB_REG_RANGE , - .flags =IORESOURCE_MEM , - .name ="capregs" , - }, -/* phybase */ - [1 ] = { - .start =PXA168_U2O_PHYBASE , - .end =PXA168_U2O_PHYBASE +USB_PHY_RANGE , - .flags =IORESOURCE_MEM , - .name ="phyregs" , - }, - [2 ] = { - .start =IRQ_PXA168_USB1 , - .end =IRQ_PXA168_USB1 , - .flags =IORESOURCE_IRQ , - }, -}; - -struct platform_device pxa168_device_u2oehci = { - .name ="pxa-u2oehci" , - .id =-1 , - .dev = { - .dma_mask = &usb_dma_mask, - .coherent_dma_mask =0xffffffff , - }, - - .num_resources =ARRAY_SIZE (pxa168_u2oehci_resources), - .resource = pxa168_u2oehci_resources, -}; -#endif - -#if defined(CONFIG_USB_MV_OTG ) -struct resource pxa168_u2ootg_resources[] = { -/* regbase */ - [0 ] = { - .start =PXA168_U2O_REGBASE + U2x_CAPREGS_OFFSET, - .end =PXA168_U2O_REGBASE +USB_REG_RANGE , - .flags =IORESOURCE_MEM , - .name ="capregs" , - }, -/* phybase */ - [1 ] = { - .start =PXA168_U2O_PHYBASE , - .end =PXA168_U2O_PHYBASE +USB_PHY_RANGE , - .flags =IORESOURCE_MEM , - .name ="phyregs" , - }, - [2 ] = { - .start =IRQ_PXA168_USB1 , - .end =IRQ_PXA168_USB1 , - .flags =IORESOURCE_IRQ , - }, -}; - -struct platform_device pxa168_device_u2ootg = { - .name ="mv-otg" , - .id =-1 , - .dev = { - .dma_mask = &usb_dma_mask, - .coherent_dma_mask =0xffffffff , - }, - - .num_resources =ARRAY_SIZE (pxa168_u2ootg_resources), - .resource = pxa168_u2ootg_resources, -}; -#endif /* CONFIG_USB_MV_OTG */ - -#endif
arch/arm/mach-mmp/include/mach/regs-usb.h deleted +0 -253
253 lines not on this page · raw message
Signature · 1 line
1.7.4.1
PATCH v7 10/16 arm: mmp: remove usb devices from pxa168
In reply to Chao Xie--- arch/arm/mach-mmp/pxa168.c | 42 ------------------------------------------ 1 files changed, 0 insertions(+), 42 deletions(-)
arch/arm/mach-mmp/pxa168.c +0 -42
@@ -28,7 +28,6 @@#include <mach/mfp.h> #include <linux/dma-mapping.h> #include <mach/pxa168.h> -#include <mach/regs-usb.h> #include "common.h" #include "clock.h"
@@ -135,47 +134,6 @@ struct platform_device pxa168_device_gpio = { .resource = pxa168_resource_gpio, }; -struct resource pxa168_usb_host_resources[] = { -/* USB Host conroller register base */ - [0 ] = { - .start =PXA168_U2H_REGBASE + U2x_CAPREGS_OFFSET, - .end =PXA168_U2H_REGBASE +USB_REG_RANGE , - .flags =IORESOURCE_MEM , - .name ="capregs" , - }, -/* USB PHY register base */ - [1 ] = { - .start =PXA168_U2H_PHYBASE , - .end =PXA168_U2H_PHYBASE +USB_PHY_RANGE , - .flags =IORESOURCE_MEM , - .name ="phyregs" , - }, - [2 ] = { - .start =IRQ_PXA168_USB2 , - .end =IRQ_PXA168_USB2 , - .flags =IORESOURCE_IRQ , - }, -}; - -static u64 pxa168_usb_host_dmamask =DMA_BIT_MASK (32 ); -struct platform_device pxa168_device_usb_host = { - .name ="pxa-sph" , - .id =-1 , - .dev = { - .dma_mask = &pxa168_usb_host_dmamask, - .coherent_dma_mask =DMA_BIT_MASK (32 ), - }, - - .num_resources =ARRAY_SIZE (pxa168_usb_host_resources), - .resource = pxa168_usb_host_resources, -}; - -int __init pxa168_add_usb_host (struct mv_usb_platform_data *pdata) -{ - pxa168_device_usb_host.dev.platform_data = pdata; -return platform_device_register (&pxa168_device_usb_host); -} -void pxa168_restart (char mode,const char *cmd) {soft_restart (0xffff0000 );
Signature · 1 line
1.7.4.1
PATCH v7 11/16 usb: phy: mv_usb2_phy: add externel chip support
In reply to Chao XieFor the vbus and idpin detection. It may be completed by some external chip, for example the pmic chip 88pm860x in driver/mfd can do it.
Although the usb controller can detect the vbus and id pin, but it need clock on and PHY enabled to detect the vbus/idpin. It will increase the power.
Using the external chip to detect vbus/idpin can save the power.
--- drivers/usb/phy/mv_usb2_phy.c | 49 ++++++++++++++++++++ include/linux/platform_data/mv_usb.h | 15 ++---- include/linux/usb/mv_usb2.h | 81 ++++++++++++++++++++++++++++++++++ 3 files changed, 135 insertions(+), 10 deletions(-)
drivers/usb/phy/mv_usb2_phy.c +49 -0
@@ -129,6 +129,53 @@ enum mv_usb2_phy_type { MMP2_USB, }; +int mv_usb2_register_notifier (struct mv_usb2_phy *phy, +struct notifier_block *nb) +{ +int ret; + +if (!phy) +return -ENODEV ; + + ret =atomic_notifier_chain_register (&phy->extern_chip.head, nb); +if (ret) +return ret; + +return 0 ; +} +EXPORT_SYMBOL (mv_usb2_register_notifier); + +int mv_usb2_unregister_notifier (struct mv_usb2_phy *phy, +struct notifier_block *nb) +{ +int ret; + +if (!phy) +return -ENODEV ; + + ret =atomic_notifier_chain_unregister (&phy->extern_chip.head, nb); +if (ret) +return ret; + +return 0 ; +} +EXPORT_SYMBOL (mv_usb2_unregister_notifier); + +int mv_usb2_notify (struct mv_usb2_phy *phy,unsigned long val,void *v) +{ +int ret; + +if (!phy) +return -ENODEV ; + + ret =atomic_notifier_call_chain (&phy->extern_chip.head, val, v); +if (ret) +return ret; + +return 0 ; +} +EXPORT_SYMBOL (mv_usb2_notify); +static unsigned int u2o_get (void __iomem *base,unsigned int offset) {return readl (base + offset);
@@ -351,6 +398,8 @@ static int mv_usb2_phy_probe(struct platform_device *pdev)usb_add_phy_dev (&mv_phy->phy); +ATOMIC_INIT_NOTIFIER_HEAD (&mv_phy->extern_chip.head); +platform_set_drvdata (pdev, mv_phy);dev_info (&pdev->dev,"mv usb2 phy initialized\n" );
include/linux/platform_data/mv_usb.h +5 -10
@@ -28,16 +28,13 @@ enum { VBUS_HIGH = 1 << 0, }; -struct mv_usb_addon_irq { -unsigned int irq; -int (*poll)(void ); -}; - +#define MV_USB_HAS_VBUS_DETECTION (1 << 0) +#define MV_USB_HAS_IDPIN_DETECTION (1 << 1)struct mv_usb_platform_data {unsigned int clknum;char **clkname; -struct mv_usb_addon_irq *id;/* Only valid for OTG. ID pin change*/ -struct mv_usb_addon_irq *vbus;/* valid for OTG/UDC. VBUS change*/ + +unsigned int extern_attr;/* only valid for HCD. OTG or Host only*/ unsigned int mode;
@@ -45,9 +42,7 @@ struct mv_usb_platform_data {/* This flag is used for that needs id pin checked by otg */ unsigned int disable_otg_clock_gating:1;/* Force a_bus_req to be asserted */ - unsigned int otg_force_a_bus_req:1; - -int (*set_vbus)(unsigned int vbus); + unsigned int otg_force_a_bus_req:1; };struct mv_usb_phy_platform_data {
include/linux/usb/mv_usb2.h +81 -0
100 lines not on this page · raw message
Signature · 1 line
1.7.4.1
PATCH v7 12/16 usb: gadget: mv_udc: add extern chip support
In reply to Chao XieBecause arch-mmp will make use of irq domain for irq allocation, the irqs allocated for PMIC is dynamical. The vbus/idpin irqs from PMIC can not be passed by platform data. Using the extern chip APIs provides by PHY driver can solve this problem.
Marvell usb PHY driver provides a middle layer.
The PMIC usb drivers will help to register the callbacks in the marvell usb PHY driver.
udc/otg/ehci driver will call the callbacks.
Then we do not need pass the information in platform data. It will remove another block in the way of enabling device tree for usb.
--- drivers/usb/gadget/mv_udc.h | 3 ++ drivers/usb/gadget/mv_udc_core.c | 56 +++++++++++++++++++++++++------------- 2 files changed, 40 insertions(+), 19 deletions(-)
drivers/usb/gadget/mv_udc.h +3 -0
@@ -178,6 +178,9 @@ struct mv_udc {struct platform_device *dev;int irq; +unsigned int extern_attr; +struct notifier_block notifier; +struct mv_cap_regs __iomem *cap_regs;struct mv_op_regs __iomem *op_regs;unsigned int max_eps;
drivers/usb/gadget/mv_udc_core.c +37 -19
139 lines not on this page · raw message
Signature · 1 line
1.7.4.1
PATCH v7 13/16 usb: ehci: ehci-mv: add extern chip support
In reply to Chao XieIt does the similar things as what we do for udc driver.
--- drivers/usb/host/ehci-mv.c | 16 ++++++++++------ 1 files changed, 10 insertions(+), 6 deletions(-)
drivers/usb/host/ehci-mv.c +10 -6
@@ -138,6 +138,7 @@ static int mv_ehci_probe(struct platform_device *pdev)struct ehci_hcd *ehci;struct ehci_hcd_mv *ehci_mv;struct resource *r; +struct mv_usb2_phy *mv_phy;int clk_i, retval = -ENODEV ;u32 offset;size_t size;
@@ -199,6 +200,7 @@ static int mv_ehci_probe(struct platform_device *pdev) retval = -ENODEV ; goto err_clear_drvdata; } + mv_phy = container_of(ehci_mv->phy, struct mv_usb2_phy, phy); retval =mv_ehci_enable (ehci_mv);if (retval) {
@@ -251,8 +253,8 @@ static int mv_ehci_probe(struct platform_device *pdev) goto err_disable_clk;#endif }else { -if (pdata->set_vbus) - pdata->set_vbus (1 ); +if (mv_usb2_has_extern_call (mv_phy, vbus, set_vbus)) +mv_usb2_extern_call (mv_phy, vbus, set_vbus,1 ); retval =usb_add_hcd (hcd, hcd->irq,IRQF_SHARED );if (retval) {
@@ -270,8 +272,8 @@ static int mv_ehci_probe(struct platform_device *pdev)return 0 ; err_set_vbus: -if (pdata->set_vbus) - pdata->set_vbus (0 ); +if (mv_usb2_has_extern_call (mv_phy, vbus, set_vbus)) +mv_usb2_extern_call (mv_phy, vbus, set_vbus,0 ); err_disable_clk:mv_ehci_disable (ehci_mv); err_clear_drvdata:
@@ -286,6 +288,7 @@ static int mv_ehci_remove(struct platform_device *pdev) {struct ehci_hcd_mv *ehci_mv =platform_get_drvdata (pdev);struct usb_hcd *hcd = ehci_mv->hcd; +struct mv_usb2_phy *mv_phy;if (hcd->rh_registered)usb_remove_hcd (hcd);
@@ -293,9 +296,10 @@ static int mv_ehci_remove(struct platform_device *pdev)if (!IS_ERR_OR_NULL (ehci_mv->otg))otg_set_host (ehci_mv->otg->otg,NULL ); + mv_phy = container_of(ehci_mv->phy, struct mv_usb2_phy, phy);if (ehci_mv->mode ==MV_USB_MODE_HOST ) { -if (ehci_mv->pdata->set_vbus) - ehci_mv->pdata->set_vbus (0 ); +if (mv_usb2_has_extern_call (mv_phy, vbus, set_vbus)) +mv_usb2_extern_call (mv_phy, vbus, set_vbus,1 );mv_ehci_disable (ehci_mv); }
Signature · 1 line
1.7.4.1
PATCH v7 14/16 usb: otg: mv_otg: add extern chip support
In reply to Chao XieIt does the similar things as what we do for udc driver.
--- drivers/usb/otg/mv_otg.c | 72 +++++++++++++++++++++++---------------------- drivers/usb/otg/mv_otg.h | 3 ++ 2 files changed, 40 insertions(+), 35 deletions(-)
drivers/usb/otg/mv_otg.c +37 -35
@@ -59,10 +59,13 @@ static char *state_string[] = {static int mv_otg_set_vbus (struct usb_otg *otg,bool on) { struct mv_otg *mvotg = container_of(otg->phy, struct mv_otg, phy); -if (mvotg->pdata->set_vbus ==NULL ) +struct mv_usb2_phy *mv_phy =container_of (mvotg->outer_phy, + struct mv_usb2_phy, phy); + +if (!mv_usb2_has_extern_call (mv_phy, vbus, set_vbus))return -ENODEV ; -return mvotg->pdata->set_vbus (on); +return mv_usb2_extern_call (mv_phy, vbus, set_vbus, on); } static int mv_otg_set_host(struct usb_otg *otg,
@@ -184,14 +187,14 @@ static void mv_otg_init_irq(struct mv_otg *mvotg) mvotg->irq_status =OTGSC_INTSTS_A_SESSION_VALID |OTGSC_INTSTS_A_VBUS_VALID ; -if (mvotg->pdata->vbus ==NULL ) { +if (!(mvotg->extern_attr &MV_USB_HAS_VBUS_DETECTION )) { mvotg->irq_en |=OTGSC_INTR_B_SESSION_VALID |OTGSC_INTR_B_SESSION_END ; mvotg->irq_status |=OTGSC_INTSTS_B_SESSION_VALID |OTGSC_INTSTS_B_SESSION_END ; } -if (mvotg->pdata->id ==NULL ) { +if (!(mvotg->extern_attr &MV_USB_HAS_IDPIN_DETECTION )) { mvotg->irq_en |=OTGSC_INTR_USB_ID ; mvotg->irq_status |=OTGSC_INTSTS_USB_ID ; }
@@ -303,11 +306,16 @@ static void mv_otg_update_inputs(struct mv_otg *mvotg) {struct mv_otg_ctrl *otg_ctrl = &mvotg->otg_ctrl;u32 otgsc; +unsigned int vbus, idpin; +struct mv_usb2_phy *mv_phy =container_of (mvotg->outer_phy, + struct mv_usb2_phy, phy); otgsc =readl (&mvotg->op_regs->otgsc); -if (mvotg->pdata->vbus) { -if (mvotg->pdata->vbus->poll () ==VBUS_HIGH ) { +if (mvotg->extern_attr &MV_USB_HAS_VBUS_DETECTION ) { +if (mv_usb2_extern_call (mv_phy, vbus, get_vbus, &vbus)) +return ; +if (vbus ==VBUS_HIGH ) { otg_ctrl->b_sess_vld =1 ; otg_ctrl->b_sess_end =0 ; }else {
@@ -319,8 +327,11 @@ static void mv_otg_update_inputs(struct mv_otg *mvotg) otg_ctrl->b_sess_end = !!(otgsc &OTGSC_STS_B_SESSION_END ); } -if (mvotg->pdata->id) - otg_ctrl->id = !!mvotg->pdata->id->poll (); +if (mvotg->extern_attr &MV_USB_HAS_IDPIN_DETECTION ) { +if (mv_usb2_extern_call (mv_phy, idpin, get_idpin, &idpin)) +return ; + otg_ctrl->id = !!idpin; + }else otg_ctrl->id = !!(otgsc &OTGSC_STS_USB_ID );
@@ -502,7 +513,7 @@ static irqreturn_t mv_otg_irq(int irq, void *dev)* if we have vbus, then the vbus detection for B-device * will be done by mv_otg_inputs_irq(). */ -if (mvotg->pdata->vbus) +if (mvotg->extern_attr &MV_USB_HAS_VBUS_DETECTION )if ((otgsc &OTGSC_STS_USB_ID ) && !(otgsc &OTGSC_INTSTS_USB_ID ))return IRQ_NONE ;
@@ -515,9 +526,10 @@ static irqreturn_t mv_otg_irq(int irq, void *dev)return IRQ_HANDLED ; } -static irqreturn_t mv_otg_inputs_irq (int irq,void *dev) +static int mv_otg_notifier_call (struct notifier_block *nb, +unsigned long val,void *v) { -struct mv_otg *mvotg = dev; + struct mv_otg *mvotg = container_of(nb, struct mv_otg, notifier);/* The clock may disabled at this time */ if (!mvotg->active) {
@@ -527,7 +539,7 @@ static irqreturn_t mv_otg_inputs_irq(int irq, void *dev)mv_otg_run_state_machine (mvotg,0 ); -return IRQ_HANDLED ; +return 0 ; } static ssize_t
@@ -660,9 +672,15 @@ static struct attribute_group inputs_attr_group = {int mv_otg_remove (struct platform_device *pdev) {struct mv_otg *mvotg =platform_get_drvdata (pdev); +struct mv_usb2_phy *mv_phy =container_of (mvotg->outer_phy, + struct mv_usb2_phy, phy);sysfs_remove_group (&mvotg->pdev->dev.kobj, &inputs_attr_group); +if ((mvotg->extern_attr &MV_USB_HAS_VBUS_DETECTION ) || + (mvotg->extern_attr &MV_USB_HAS_IDPIN_DETECTION )) +mv_usb2_unregister_notifier (mv_phy, &mvotg->notifier); +if (mvotg->qwork) {flush_workqueue (mvotg->qwork);destroy_workqueue (mvotg->qwork);
@@ -681,6 +699,7 @@ static int mv_otg_probe(struct platform_device *pdev)struct mv_otg *mvotg;struct usb_otg *otg;struct resource *r; +struct mv_usb2_phy *mv_phy;int retval =0 , clk_i, i;size_t size;
@@ -703,6 +722,7 @@ static int mv_otg_probe(struct platform_device *pdev)platform_set_drvdata (pdev, mvotg); mvotg->pdev = pdev; + mvotg->extern_attr = pdata->extern_attr; mvotg->pdata = pdata; mvotg->clknum = pdata->clknum;
@@ -759,6 +779,7 @@ static int mv_otg_probe(struct platform_device *pdev)dev_err (&pdev->dev,"can not find outer phy\n" ); goto err_destroy_workqueue; } + mv_phy = container_of(mvotg->outer_phy, struct mv_usb2_phy, phy);/* we will acces controller register, so enable the udc controller */ retval =mv_otg_enable_internal (mvotg);
@@ -771,29 +792,10 @@ static int mv_otg_probe(struct platform_device *pdev) (struct mv_otg_regs __iomem *) ((unsigned long ) mvotg->cap_regs + (readl (mvotg->cap_regs) &CAPLENGTH_MASK )); -if (pdata->id) { - retval =devm_request_threaded_irq (&pdev->dev, pdata->id->irq, -NULL , mv_otg_inputs_irq, -IRQF_ONESHOT ,"id" , mvotg); -if (retval) { -dev_info (&pdev->dev, -"Failed to request irq for ID\n" ); - pdata->id =NULL ; - } - } - -if (pdata->vbus) { - mvotg->clock_gating =1 ; - retval =devm_request_threaded_irq (&pdev->dev, pdata->vbus->irq, -NULL , mv_otg_inputs_irq, -IRQF_ONESHOT ,"vbus" , mvotg); -if (retval) { -dev_info (&pdev->dev, -"Failed to request irq for VBUS, " -"disable clock gating\n" ); - mvotg->clock_gating =0 ; - pdata->vbus =NULL ; - } +if ((mvotg->extern_attr &MV_USB_HAS_VBUS_DETECTION ) || + (mvotg->extern_attr &MV_USB_HAS_IDPIN_DETECTION )) { + mvotg->notifier.notifier_call = mv_otg_notifier_call; +mv_usb2_register_notifier (mv_phy, &mvotg->notifier); }if (pdata->disable_otg_clock_gating)
drivers/usb/otg/mv_otg.h +3 -0
@@ -149,6 +149,9 @@ struct mv_otg {u32 irq_status;u32 irq_en; +unsigned int extern_attr; +struct notifier_block notifier; +struct delayed_work work;struct workqueue_struct *qwork;
Signature · 1 line
1.7.4.1
PATCH v7 15/16 arm: mmp: add extern chip support for brownstone
In reply to Chao XieChange the board support for usb as extern chip is supported in marvell usb PHY driver
--- arch/arm/mach-mmp/brownstone.c | 2 -- 1 files changed, 0 insertions(+), 2 deletions(-)
arch/arm/mach-mmp/brownstone.c +0 -2
@@ -214,10 +214,8 @@ static struct mv_usb_phy_platform_data brownstone_usb_phy_pdata = {static struct mv_usb_platform_data brownstone_usb_pdata = { .clknum =1 , .clkname = mmp2_usb_clock_name, - .vbus =NULL , .mode =MV_USB_MODE_OTG , .otg_force_a_bus_req =1 , - .set_vbus =NULL , };#endif #endif
Signature · 1 line
1.7.4.1
PATCH v7 16/16 arm: mmp: add extern chip support for ttc_dkb
In reply to Chao XieChange the board support for usb as extern chip is supported in marvell usb PHY driver.
--- arch/arm/mach-mmp/ttc_dkb.c | 2 -- 1 files changed, 0 insertions(+), 2 deletions(-)
arch/arm/mach-mmp/ttc_dkb.c +0 -2
@@ -174,10 +174,8 @@ static struct mv_usb_phy_platform_data ttc_usb_phy_pdata = {static struct mv_usb_platform_data ttc_usb_pdata = { .clknum =1 , .clkname = pxa910_usb_clock_name, - .vbus =NULL , .mode =MV_USB_MODE_OTG , .otg_force_a_bus_req =1 , - .set_vbus =NULL , };#endif #endif
Signature · 1 line
1.7.4.1