ARM; OMAP2+: hwmod and SERIAL: Remove sysc handling from driver
Subsystems (4)
cover ARM; OMAP2+: hwmod and SERIAL: Remove sysc handling from driver
OMAP UART IP needs manual idle modes based on functional state of the IP. Currently this is handled by the driver with function pointers implemented in platform code.
This however breaks in case of device tree because of missing idle handling.
The series tries to address the issue and tries to remove complete sysc handling from serial driver.
Patches has been tested on OMAP4430 SDP and OMAP5 EVM where the console sluggishness was observed without idle mode handling. CPUIDLE and suspend tested ok on these devices.
Thanks to Vaibhav Bedia for testing on Beaglebone(AM33XX) with suspend and also the UART async wakeup from suspend.
Thanks to Sourav Poddar for Beagle XM(OMAP3630) devices testing with retention and offmode in Idle and suspend for non-DT builds.
Serial driver platform code still has one more function pointer left which is used to trigger io_ring(). This one needs some discussion with pincontrol driver folks on how to implement such a feature with generic pincontrol driver.
Rajendra Nayak (4):
ARM: OMAP2+: hwmod: Remove unused _HWMOD_WAKEUP_ENABLED flag
ARM: OMAP2+: hwmod: Cleanup sidle/mstandby programming
ARM: OMAP2+: hwmod: Always have OCP_SYSCONFIG.ENAWAKEUP enabled
ARM: OMAP2+: hwmod: Add a new flag to handle SIDLE in SWSUP only in
active
Santosh Shilimkar (4):
ARM: OMAP2+: hwmod-data: UART IP needs software control to manage
sidle modes
SERIAL: OMAP: Remove the slave idle handling from the driver
ARM: OMAP2+: serial: Remove the un-used slave idle hooks
ARM: OMAP2+: hwmod: Remove sysc slave idle and auto idle apis
arch/arm/mach-omap2/omap_hwmod.c | 141 ++++---------------- arch/arm/mach-omap2/omap_hwmod.h | 13 +- arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c | 3 + arch/arm/mach-omap2/omap_hwmod_33xx_data.c | 6 + arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 4 + arch/arm/mach-omap2/omap_hwmod_44xx_data.c | 6 +- arch/arm/mach-omap2/serial.c | 31 ----- drivers/tty/serial/omap-serial.c | 23 ---- 8 files changed, 50 insertions(+), 177 deletions(-)
Signature · 1 line
1.7.9.5
PATCH 1/8 ARM: OMAP2+: hwmod: Remove unused _HWMOD_WAKEUP_ENABLED flag
From: Rajendra Nayak <[email protected]>
_HWMOD_WAKEUP_ENABLED is currently unused across the hwmod framework. Just get rid of it, so we have one less flag to worry about.
--- arch/arm/mach-omap2/omap_hwmod.c | 4 ---- arch/arm/mach-omap2/omap_hwmod.h | 6 ++---- 2 files changed, 2 insertions(+), 8 deletions(-)
arch/arm/mach-omap2/omap_hwmod.c +0 -4
@@ -608,8 +608,6 @@ static int _enable_wakeup(struct omap_hwmod *oh, u32 *v)/* XXX test pwrdm_get_wken for this hwmod's subsystem */ - oh->_int_flags |= _HWMOD_WAKEUP_ENABLED; -return 0 ; }
@@ -643,8 +641,6 @@ static int _disable_wakeup(struct omap_hwmod *oh, u32 *v)/* XXX test pwrdm_get_wken for this hwmod's subsystem */ - oh->_int_flags &= ~_HWMOD_WAKEUP_ENABLED; -return 0 ; }
arch/arm/mach-omap2/omap_hwmod.h +2 -4
@@ -468,15 +468,13 @@ struct omap_hwmod_omap4_prcm {* These are for internal use only and are managed by the omap_hwmod code. * * _HWMOD_NO_MPU_PORT: no path exists for the MPU to write to this module -* _HWMOD_WAKEUP_ENABLED: set when the omap_hwmod code has enabled ENAWAKEUP * _HWMOD_SYSCONFIG_LOADED: set when the OCP_SYSCONFIG value has been cached * _HWMOD_SKIP_ENABLE: set if hwmod enabled during init (HWMOD_INIT_NO_IDLE) - * causes the first call to _enable() to only update the pinmux */ #define _HWMOD_NO_MPU_PORT (1 << 0) -#define _HWMOD_WAKEUP_ENABLED (1 << 1) -#define _HWMOD_SYSCONFIG_LOADED (1 << 2) -#define _HWMOD_SKIP_ENABLE (1 << 3) +#define _HWMOD_SYSCONFIG_LOADED (1 << 1) +#define _HWMOD_SKIP_ENABLE (1 << 2)/* * omap_hwmod._state definitions
Signature · 1 line
1.7.9.5
Paul Walmsley
maintainerPATCH 1/8 ARM: OMAP2+: hwmod: Remove unused _HWMOD_WAKEUP_ENABLED flag
Quoted 9 lines · Santosh Shilimkar
From: Rajendra Nayak <[email protected]>
_HWMOD_WAKEUP_ENABLEDis currently unused across the hwmod framework. Just get rid of it, so we have one less flag to worry about.Tested-by Vaibhav Bedia <[email protected]>Signed-off-by Rajendra Nayak <[email protected]>Signed-off-by Santosh Shilimkar <[email protected]>
Thanks, queued for 3.9.
- Paul
Paul Walmsley
maintainerPATCH 1/8 ARM: OMAP2+: hwmod: Remove unused _HWMOD_WAKEUP_ENABLED flag
Quoted 8 lines · Paul Walmsley
Quoted 6 lines · Santosh Shilimkar
From: Rajendra Nayak <[email protected]>
_HWMOD_WAKEUP_ENABLEDis currently unused across the hwmod framework. Just get rid of it, so we have one less flag to worry about.
Quoted 5 lines
Quoted 3 lines
Tested-by Vaibhav Bedia <[email protected]>Signed-off-by Rajendra Nayak <[email protected]>Signed-off-by Santosh Shilimkar <[email protected]>Thanks, queued for 3.9.
Err, 3.10, rather.
- Paul
PATCH 2/8 ARM: OMAP2+: hwmod: Cleanup sidle/mstandby programming
In reply to Santosh ShilimkarFrom: Rajendra Nayak <[email protected]>
_enable_wakeup() and _disable_wakeup() are expected to program the OCP_SYSCONFIG.ENAWAKEUP bit. Get rid of the additional sidle/mstandby programming in them, as its confusing (this is expected to be handled elsewhere as part of _enable_sysc()/__idle_sysc()) and unnecessary.
Well, the _enable_sysc()/_idle_sysc() handled only the mstandby modes correctly. So fix them so they also handle the midle modes correctly and program HWMOD_IDLEMODE_SMART_WKUP and HWMOD_IDLEMODE_SMART respectively.
--- arch/arm/mach-omap2/omap_hwmod.c | 48 ++++++++++++++++++-------------------- 1 file changed, 23 insertions(+), 25 deletions(-)
arch/arm/mach-omap2/omap_hwmod.c +23 -25
@@ -588,9 +588,7 @@ static void _set_idle_ioring_wakeup(struct omap_hwmod *oh, bool set_wake)static int _enable_wakeup (struct omap_hwmod *oh,u32 *v) {if (!oh->class->sysc || - !((oh->class->sysc->sysc_flags &SYSC_HAS_ENAWAKEUP ) || - (oh->class->sysc->idlemodes &SIDLE_SMART_WKUP ) || - (oh->class->sysc->idlemodes &MSTANDBY_SMART_WKUP ))) + !(oh->class->sysc->sysc_flags &SYSC_HAS_ENAWAKEUP ))return -EINVAL ;if (!oh->class->sysc->sysc_fields) {
@@ -601,11 +599,6 @@ static int _enable_wakeup(struct omap_hwmod *oh, u32 *v)if (oh->class->sysc->sysc_flags &SYSC_HAS_ENAWAKEUP ) *v |=0x1 << oh->class->sysc->sysc_fields->enwkup_shift; -if (oh->class->sysc->idlemodes &SIDLE_SMART_WKUP ) -_set_slave_idlemode (oh,HWMOD_IDLEMODE_SMART_WKUP , v); -if (oh->class->sysc->idlemodes &MSTANDBY_SMART_WKUP ) -_set_master_standbymode (oh,HWMOD_IDLEMODE_SMART_WKUP , v); -/* XXX test pwrdm_get_wken for this hwmod's subsystem */ return 0 ;
@@ -621,9 +614,7 @@ static int _enable_wakeup(struct omap_hwmod *oh, u32 *v)static int _disable_wakeup (struct omap_hwmod *oh,u32 *v) {if (!oh->class->sysc || - !((oh->class->sysc->sysc_flags &SYSC_HAS_ENAWAKEUP ) || - (oh->class->sysc->idlemodes &SIDLE_SMART_WKUP ) || - (oh->class->sysc->idlemodes &MSTANDBY_SMART_WKUP ))) + !(oh->class->sysc->sysc_flags &SYSC_HAS_ENAWAKEUP ))return -EINVAL ;if (!oh->class->sysc->sysc_fields) {
@@ -634,11 +625,6 @@ static int _disable_wakeup(struct omap_hwmod *oh, u32 *v)if (oh->class->sysc->sysc_flags &SYSC_HAS_ENAWAKEUP ) *v &= ~(0x1 << oh->class->sysc->sysc_fields->enwkup_shift); -if (oh->class->sysc->idlemodes &SIDLE_SMART_WKUP ) -_set_slave_idlemode (oh,HWMOD_IDLEMODE_SMART , v); -if (oh->class->sysc->idlemodes &MSTANDBY_SMART_WKUP ) -_set_master_standbymode (oh,HWMOD_IDLEMODE_SMART , v); -/* XXX test pwrdm_get_wken for this hwmod's subsystem */ return 0 ;
@@ -1351,13 +1337,24 @@ static void _enable_sysc(struct omap_hwmod *oh) clkdm =_get_clkdm (oh);if (sf &SYSC_HAS_SIDLEMODE ) { +if (oh->flags &HWMOD_SWSUP_SIDLE ) { + idlemode =HWMOD_IDLEMODE_NO ; + }else { +if (oh->class->sysc->idlemodes &SIDLE_SMART_WKUP ) + idlemode =HWMOD_IDLEMODE_SMART_WKUP ; +else + idlemode =HWMOD_IDLEMODE_SMART ; + } + +/* +* This is special handling for some IPs like +* 32k sync timer. Force them to idle! +*/ clkdm_act = (clkdm && clkdm->flags &CLKDM_ACTIVE_WITH_MPU );if (clkdm_act && !(oh->class->sysc->idlemodes & (SIDLE_SMART |SIDLE_SMART_WKUP ))) idlemode =HWMOD_IDLEMODE_FORCE ; -else - idlemode = (oh->flags &HWMOD_SWSUP_SIDLE ) ? -HWMOD_IDLEMODE_NO :HWMOD_IDLEMODE_SMART ; +_set_slave_idlemode (oh, idlemode, &v); }
@@ -1423,13 +1420,14 @@ static void _idle_sysc(struct omap_hwmod *oh) sf = oh->class->sysc->sysc_flags;if (sf &SYSC_HAS_SIDLEMODE ) { -/* XXX What about HWMOD_IDLEMODE_SMART_WKUP? */ -if (oh->flags &HWMOD_SWSUP_SIDLE || - !(oh->class->sysc->idlemodes & - (SIDLE_SMART |SIDLE_SMART_WKUP ))) +if (oh->flags &HWMOD_SWSUP_SIDLE ) { idlemode =HWMOD_IDLEMODE_FORCE ; -else - idlemode =HWMOD_IDLEMODE_SMART ; + }else { +if (oh->class->sysc->idlemodes &SIDLE_SMART_WKUP ) + idlemode =HWMOD_IDLEMODE_SMART_WKUP ; +else + idlemode =HWMOD_IDLEMODE_SMART ; + }_set_slave_idlemode (oh, idlemode, &v); }
Signature · 1 line
1.7.9.5
Paul Walmsley
maintainerPATCH 2/8 ARM: OMAP2+: hwmod: Cleanup sidle/mstandby programming
Hi
Quoted 4 lines · Santosh Shilimkar
From: Rajendra Nayak <[email protected]>
_enable_wakeup()and_disable_wakeup()are expected to program the OCP_SYSCONFIG.ENAWAKEUP bit.
These functions were originally intended to take care of everything needed for the IP block to wake up the chip, including the PRCM WKEN programming. ENAWAKEUP is simply one part of that.
Quoted 3 lines
Get rid of the additional sidle/mstandby programming in them, as its confusing (this is expected to be handled elsewhere as part of _enable_sysc()/__idle_sysc())
Sorry, why does the expectation exist for the code to enable and disable device wakeup to be part of _enable_sysc()/_idle_sysc(), rather than in functions called by _enable_sysc()/_idle_sysc()?
Quoted 1 line
and unnecessary.
So here's part of the reason why the module wakeup control functions should remain separate. When the kernel boots, all the PM features should be disabled. Then mach-omap2/pm*.c should enables PM features where they're needed.
Right now, mach-omap2/pm34xx.c sets module WKEN bits. (These direct register accesses need to be moved as part of the cleanup work, of moving the PM/PRM/CM code into drivers.) But the list of IP blocks that should be allowed to wake the system is board-dependent.
So really, what mach-omap2/pm34xx.c should do is to call into the hwmod enable-wakeups code to enable MPU wakeups for all the IP blocks that have some DT property set, something like 'enable-wakeups'. Then the hwmod code should ensure that the PRM wakeup-enable and GRPSEL bits are programmed (by calling into the PRM driver code) and should then either set the ENAWAKEUP bits or put the module into smart_wkup MSTANDBY/MIDLE.
Similarly, when the PM driver is unloaded, it should set no-idle on all the IP blocks that were marked as wakeup-capable and disable the PRCM wakeup control bits, by calling some hwmod disable-wakeups code.
Quoted 2 lines
Well, the _enable_sysc()/_idle_sysc() handled only the mstandby modes correctly. So fix them so they also handle the midle modes correctly
If there's a fix here, please split that out into a separate patch.
- Paul
PATCH 2/8 ARM: OMAP2+: hwmod: Cleanup sidle/mstandby programming
Paul,
Quoted 7 lines
Quoted 2 lines
_enable_wakeup()and_disable_wakeup()are expected to program the OCP_SYSCONFIG.ENAWAKEUP bit.These functions were originally intended to take care of everything needed for the IP block to wake up the chip, including the PRCM WKEN programming. ENAWAKEUP is simply one part of that.
Quoted 7 lines
Quoted 3 lines
Get rid of the additional sidle/mstandby programming in them, as its confusing (this is expected to be handled elsewhere as part of _enable_sysc()/__idle_sysc())
Sorry, why does the expectation exist for the code to enable and disable device wakeup to be part of _enable_sysc()/_idle_sysc(), rather than in functions called by _enable_sysc()/_idle_sysc()?
It all comes down to if SIDLE_SMART_WKUP/MSTANDBY_SMART_WKUP programming be considered as 'idlemode' programming or 'enwakeup' programming. If you consider these are being part of 'enwakeup' progrmming, these should certainly be handled as part of _enable_wakeup() and _disable_wakeup().
Today, in some cases, these are *also* handled as part of _enable_sysc() and _idle_sysc(). The way _enable_wakeup() is invoked from _enable_sysc() is also very inconsistent. For instance, for any IP which supports SYSC_HAS_MIDLEMODE and SYSC_HAS_ENAWAKEUP, we invoke _enable_wakeup() regardless of the MIDLEMODE programmmed.
While in case of the IP supporting SYSC_HAS_SIDLEMODE, _enable_wakeup() is invoked only when the SIDLEMODE programmed is SMART or SMART_WKUP.
I understand the cleanups you are suggesting below as part of the movement of some of these things outside of mach-omap2.
I was more looking at fixing the existing piece so its readable and does things more consistently.
regards,
Rajendra
Quoted 32 lines
Quoted 2 lines
and unnecessary.
So here's part of the reason why the module wakeup control functions should remain separate. When the kernel boots, all the PM features should be disabled. Then
mach-omap2/pm*.cshould enables PM features where they're needed.Right now,
mach-omap2/pm34xx.csets module WKEN bits. (These direct register accesses need to be moved as part of the cleanup work, of moving the PM/PRM/CM code into drivers.) But the list of IP blocks that should be allowed to wake the system is board-dependent.So really, what
mach-omap2/pm34xx.cshould do is to call into the hwmod enable-wakeups code to enable MPU wakeups for all the IP blocks that have some DT property set, something like 'enable-wakeups'. Then the hwmod code should ensure that the PRM wakeup-enable and GRPSEL bits are programmed (by calling into the PRM driver code) and should then either set the ENAWAKEUP bits or put the module intosmart_wkupMSTANDBY/MIDLE.Similarly, when the PM driver is unloaded, it should set no-idle on all the IP blocks that were marked as wakeup-capable and disable the PRCM wakeup control bits, by calling some hwmod disable-wakeups code.
Quoted 2 lines
Well, the _enable_sysc()/_idle_sysc() handled only the mstandby modes correctly. So fix them so they also handle the midle modes correctly
If there's a fix here, please split that out into a separate patch.
- Paul
PATCH 2/8 ARM: OMAP2+: hwmod: Cleanup sidle/mstandby programming
Hi Paul,
Quoted 28 lines
Quoted 7 lines
Quoted 2 lines
_enable_wakeup()and_disable_wakeup()are expected to program the OCP_SYSCONFIG.ENAWAKEUP bit.These functions were originally intended to take care of everything needed for the IP block to wake up the chip, including the PRCM WKEN programming. ENAWAKEUP is simply one part of that.
Quoted 7 lines
Quoted 3 lines
Get rid of the additional sidle/mstandby programming in them, as its confusing (this is expected to be handled elsewhere as part of _enable_sysc()/__idle_sysc())
Sorry, why does the expectation exist for the code to enable and disable device wakeup to be part of _enable_sysc()/_idle_sysc(), rather than in functions called by _enable_sysc()/_idle_sysc()?
It all comes down to if SIDLE_SMART_WKUP/MSTANDBY_SMART_WKUP programming be considered as 'idlemode' programming or 'enwakeup' programming. If you consider these are being part of 'enwakeup' progrmming, these should certainly be handled as part of
_enable_wakeup()and_disable_wakeup().Today, in some cases, these are *also* handled as part of
_enable_sysc()and_idle_sysc(). The way_enable_wakeup()is invoked from_enable_sysc()is also very inconsistent. For instance, for any IP which supportsSYSC_HAS_MIDLEMODEandSYSC_HAS_ENAWAKEUP, we invoke_enable_wakeup()regardless of the MIDLEMODE programmmed.
While in case of the IP supportingSYSC_HAS_SIDLEMODE,_enable_wakeup()is invoked only when the SIDLEMODE programmed is SMART orSMART_WKUP.
Quoted 4 lines
I understand the cleanups you are suggesting below as part of the movement of some of these things outside of mach-omap2.
I was more looking at fixing the existing piece so its readable and does things more consistently.
Do you have any further thoughts on how we should do about this?
regards,
Rajendra
Quoted 37 lines
regards,
RajendraQuoted 32 lines
Quoted 2 lines
and unnecessary.
So here's part of the reason why the module wakeup control functions should remain separate. When the kernel boots, all the PM features should be disabled. Then
mach-omap2/pm*.cshould enables PM features where they're needed.Right now,
mach-omap2/pm34xx.csets module WKEN bits. (These direct register accesses need to be moved as part of the cleanup work, of moving the PM/PRM/CM code into drivers.) But the list of IP blocks that should be allowed to wake the system is board-dependent.So really, what
mach-omap2/pm34xx.cshould do is to call into the hwmod enable-wakeups code to enable MPU wakeups for all the IP blocks that have some DT property set, something like 'enable-wakeups'. Then the hwmod code should ensure that the PRM wakeup-enable and GRPSEL bits are programmed (by calling into the PRM driver code) and should then either set the ENAWAKEUP bits or put the module intosmart_wkupMSTANDBY/MIDLE.Similarly, when the PM driver is unloaded, it should set no-idle on all the IP blocks that were marked as wakeup-capable and disable the PRCM wakeup control bits, by calling some hwmod disable-wakeups code.
Quoted 2 lines
Well, the _enable_sysc()/_idle_sysc() handled only the mstandby modes correctly. So fix them so they also handle the midle modes correctly
If there's a fix here, please split that out into a separate patch.
- Paul
Paul Walmsley
maintainerPATCH 2/8 ARM: OMAP2+: hwmod: Cleanup sidle/mstandby programming
Hi Rajendra,
Quoted 28 lines · Rajendra Nayak
Quoted 28 lines
Quoted 7 lines
Quoted 2 lines
_enable_wakeup()and_disable_wakeup()are expected to program the OCP_SYSCONFIG.ENAWAKEUP bit.These functions were originally intended to take care of everything needed for the IP block to wake up the chip, including the PRCM WKEN programming. ENAWAKEUP is simply one part of that.
Quoted 7 lines
Quoted 3 lines
Get rid of the additional sidle/mstandby programming in them, as its confusing (this is expected to be handled elsewhere as part of _enable_sysc()/__idle_sysc())
Sorry, why does the expectation exist for the code to enable and disable device wakeup to be part of _enable_sysc()/_idle_sysc(), rather than in functions called by _enable_sysc()/_idle_sysc()?
It all comes down to if SIDLE_SMART_WKUP/MSTANDBY_SMART_WKUP programming be considered as 'idlemode' programming or 'enwakeup' programming. If you consider these are being part of 'enwakeup' progrmming, these should certainly be handled as part of
_enable_wakeup()and_disable_wakeup().Today, in some cases, these are *also* handled as part of
_enable_sysc()and_idle_sysc(). The way_enable_wakeup()is invoked from_enable_sysc()is also very inconsistent. For instance, for any IP which supportsSYSC_HAS_MIDLEMODEandSYSC_HAS_ENAWAKEUP, we invoke_enable_wakeup()regardless of the MIDLEMODE programmmed.
While in case of the IP supportingSYSC_HAS_SIDLEMODE,_enable_wakeup()is invoked only when the SIDLEMODE programmed is SMART orSMART_WKUP.
Quoted 6 lines
Quoted 4 lines
I understand the cleanups you are suggesting below as part of the movement of some of these things outside of mach-omap2.
I was more looking at fixing the existing piece so its readable and does things more consistently.Do you have any further thoughts on how we should do about this?
Is it possible to implement a solution that preserves _enable_wakeup() and _disable_wakeup() as distinct functions, that can be called by separate wakeup control entry points?
If it makes sense to change _enable_sysc() so that it doesn't call _enable_wakeup(), but does similar work itself, that's fine with me, as long as there's not too much code duplication.
It will be good to have the inconsistencies fixed.
- Paul
PATCH 2/8 ARM: OMAP2+: hwmod: Cleanup sidle/mstandby programming
Quoted 43 lines · Paul Walmsley
Hi Rajendra,
Quoted 28 lines · Rajendra Nayak
Quoted 28 lines
Quoted 7 lines
Quoted 2 lines
_enable_wakeup()and_disable_wakeup()are expected to program the OCP_SYSCONFIG.ENAWAKEUP bit.These functions were originally intended to take care of everything needed for the IP block to wake up the chip, including the PRCM WKEN programming. ENAWAKEUP is simply one part of that.
Quoted 7 lines
Quoted 3 lines
Get rid of the additional sidle/mstandby programming in them, as its confusing (this is expected to be handled elsewhere as part of _enable_sysc()/__idle_sysc())
Sorry, why does the expectation exist for the code to enable and disable device wakeup to be part of _enable_sysc()/_idle_sysc(), rather than in functions called by _enable_sysc()/_idle_sysc()?
It all comes down to if SIDLE_SMART_WKUP/MSTANDBY_SMART_WKUP programming be considered as 'idlemode' programming or 'enwakeup' programming. If you consider these are being part of 'enwakeup' progrmming, these should certainly be handled as part of
_enable_wakeup()and_disable_wakeup().Today, in some cases, these are *also* handled as part of
_enable_sysc()and_idle_sysc(). The way_enable_wakeup()is invoked from_enable_sysc()is also very inconsistent. For instance, for any IP which supportsSYSC_HAS_MIDLEMODEandSYSC_HAS_ENAWAKEUP, we invoke_enable_wakeup()regardless of the MIDLEMODE programmmed.
While in case of the IP supportingSYSC_HAS_SIDLEMODE,_enable_wakeup()is invoked only when the SIDLEMODE programmed is SMART orSMART_WKUP.Quoted 6 lines
Quoted 4 lines
I understand the cleanups you are suggesting below as part of the movement of some of these things outside of mach-omap2.
I was more looking at fixing the existing piece so its readable and does things more consistently.Do you have any further thoughts on how we should do about this?
Is it possible to implement a solution that preserves
_enable_wakeup()and_disable_wakeup()as distinct functions, that can be called by separate wakeup control entry points?
Quoted 5 lines
If it makes sense to change
_enable_sysc()so that it doesn't call_enable_wakeup(), but does similar work itself, that's fine with me, as long as there's not too much code duplication.It will be good to have the inconsistencies fixed.
Sure, I'll post something on those lines shortly.
regards,
Rajendra
Quoted 4 lines
- Paul
PATCH 3/8 ARM: OMAP2+: hwmod: Always have OCP_SYSCONFIG.ENAWAKEUP enabled
In reply to Santosh ShilimkarFrom: Rajendra Nayak <[email protected]>
Get rid of all complexities around when to enable OCP_SYSCONFIG.ENAWAKEUP. It should be safe to have this set *always* for all IP blocks which have this control. It should be a *dont care* when the IP is in NO/FORCE modes of sidle/mstandby. As for the SMART/SMART_WKUP modes of sidle/mstandby the framework anyway sets this always.
--- arch/arm/mach-omap2/omap_hwmod.c | 20 ++------------------ 1 file changed, 2 insertions(+), 18 deletions(-)
arch/arm/mach-omap2/omap_hwmod.c +2 -18
@@ -1362,8 +1362,6 @@ static void _enable_sysc(struct omap_hwmod *oh)if (oh->flags &HWMOD_SWSUP_MSTANDBY ) { idlemode =HWMOD_IDLEMODE_NO ; }else { -if (sf &SYSC_HAS_ENAWAKEUP ) -_enable_wakeup (oh, &v);if (oh->class->sysc->idlemodes &MSTANDBY_SMART_WKUP ) idlemode =HWMOD_IDLEMODE_SMART_WKUP ;else
@@ -1381,9 +1379,7 @@ static void _enable_sysc(struct omap_hwmod *oh) (sf & SYSC_HAS_CLOCKACTIVITY))_set_clockactivity (oh, oh->class->sysc->clockact, &v); -/* If slave is in SMARTIDLE, also enable wakeup */ -if ((sf &SYSC_HAS_SIDLEMODE ) && !(oh->flags &HWMOD_SWSUP_SIDLE )) -_enable_wakeup (oh, &v); +_enable_wakeup (oh, &v);_write_sysconfig (v, oh);
@@ -1435,8 +1431,6 @@ static void _idle_sysc(struct omap_hwmod *oh)if (oh->flags &HWMOD_SWSUP_MSTANDBY ) { idlemode =HWMOD_IDLEMODE_FORCE ; }else { -if (sf &SYSC_HAS_ENAWAKEUP ) -_enable_wakeup (oh, &v);if (oh->class->sysc->idlemodes &MSTANDBY_SMART_WKUP ) idlemode =HWMOD_IDLEMODE_SMART_WKUP ;else
@@ -1445,9 +1439,7 @@ static void _idle_sysc(struct omap_hwmod *oh)_set_master_standbymode (oh, idlemode, &v); } -/* If slave is in SMARTIDLE, also enable wakeup */ -if ((sf &SYSC_HAS_SIDLEMODE ) && !(oh->flags &HWMOD_SWSUP_SIDLE )) -_enable_wakeup (oh, &v); +_enable_wakeup (oh, &v);_write_sysconfig (v, oh); }
@@ -3767,14 +3759,6 @@ int omap_hwmod_enable_wakeup(struct omap_hwmod *oh)u32 v;spin_lock_irqsave (&oh->_lock, flags); - -if (oh->class->sysc && - (oh->class->sysc->sysc_flags &SYSC_HAS_ENAWAKEUP )) { - v = oh->_sysc_cache; -_enable_wakeup (oh, &v); -_write_sysconfig (v, oh); - } -_set_idle_ioring_wakeup (oh, true);spin_unlock_irqrestore (&oh->_lock, flags);
Signature · 1 line
1.7.9.5
Paul Walmsley
maintainerPATCH 3/8 ARM: OMAP2+: hwmod: Always have OCP_SYSCONFIG.ENAWAKEUP enabled
Quoted 8 lines · Santosh Shilimkar
From: Rajendra Nayak <[email protected]>
Get rid of all complexities around when to enable OCP_SYSCONFIG.ENAWAKEUP. It should be safe to have this set *always* for all IP blocks which have this control. It should be a *dont care* when the IP is in NO/FORCE modes of sidle/mstandby. As for the SMART/SMART_WKUP modes of sidle/mstandby the framework anyway sets this always.
Quoted 4 lines
Tested-by Vaibhav Bedia <[email protected]>Tested-by Sourav Poddar <[email protected]>Signed-off-by Rajendra Nayak <[email protected]>Signed-off-by Santosh Shilimkar <[email protected]>
Some of the comments here:
http://marc.info/?l=linux-omap&m=136469345727226&w=2
apply to this patch as well.
- Paul
PATCH 4/8 ARM: OMAP2+: hwmod: Add a new flag to handle SIDLE in SWSUP only in active
In reply to Santosh ShilimkarFrom: Rajendra Nayak <[email protected]>
Some IPs (like UART) need the sidle mode to be controlled in SW only while they are active. Once they go inactive, they need the IP to be put back in HW control so they are also wakeup capable.
The flag HWMOD_SWSUP_SIDLE takes care of IPs which need the sidle mode to be *always* controlled in SWSUP. We now have a need to control IPs sidle mode in SWSUP only while its active.
So define a new flag 'HWMOD_SWSUP_SIDLE_ACT' to help the framework know about these new IP requirements.
--- arch/arm/mach-omap2/omap_hwmod.c | 3 ++- arch/arm/mach-omap2/omap_hwmod.h | 4 ++++ 2 files changed, 6 insertions(+), 1 deletion(-)
arch/arm/mach-omap2/omap_hwmod.c +2 -1
@@ -1337,7 +1337,8 @@ static void _enable_sysc(struct omap_hwmod *oh) clkdm =_get_clkdm (oh);if (sf &SYSC_HAS_SIDLEMODE ) { -if (oh->flags &HWMOD_SWSUP_SIDLE ) { +if (oh->flags &HWMOD_SWSUP_SIDLE || + oh->flags &HWMOD_SWSUP_SIDLE_ACT ) { idlemode =HWMOD_IDLEMODE_NO ; }else {if (oh->class->sysc->idlemodes &SIDLE_SMART_WKUP )
arch/arm/mach-omap2/omap_hwmod.h +4 -0
@@ -451,6 +451,9 @@ struct omap_hwmod_omap4_prcm {* enabled. This prevents the hwmod code from being able to * enable and reset the IP block early. XXX Eventually it should * be possible to query the clock framework for this information. +* HWMOD_SWSUP_SIDLE_ACT: omap_hwmod code should manually bring the module out of +* idle, but rely on smart-idle to the put it back in idle, so the wakeups +* are still functional (Only known case for now is UART) */ #define HWMOD_SWSUP_SIDLE (1 << 0)#define HWMOD_SWSUP_MSTANDBY (1 << 1)
@@ -462,6 +465,7 @@ struct omap_hwmod_omap4_prcm {#define HWMOD_CONTROL_OPT_CLKS_IN_RESET (1 << 7)#define HWMOD_16BIT_REG (1 << 8)#define HWMOD_EXT_OPT_MAIN_CLK (1 << 9) +#define HWMOD_SWSUP_SIDLE_ACT (1 << 10)/* * omap_hwmod._int_flags definitions
Signature · 1 line
1.7.9.5
cover ARM; OMAP2+: hwmod and SERIAL: Remove sysc handling from driver
In reply to Santosh Shilimkar+ Felipe ( Sorry I missed you in CC list)
Quoted 49 lines · Santosh Shilimkar
OMAP UART IP needs manual idle modes based on functional state of the IP. Currently this is handled by the driver with function pointers implemented in platform code.
This however breaks in case of device tree because of missing idle handling.
The series tries to address the issue and tries to remove complete sysc handling from serial driver.
Patches has been tested on OMAP4430 SDP and OMAP5 EVM where the console sluggishness was observed without idle mode handling. CPUIDLE and suspend tested ok on these devices.
Thanks to Vaibhav Bedia for testing on Beaglebone(AM33XX) with suspend and also the UART async wakeup from suspend.
Thanks to Sourav Poddar for Beagle XM(OMAP3630) devices testing with retention and offmode in Idle and suspend for non-DT builds.
Serial driver platform code still has one more function pointer left which is used to trigger
io_ring(). This one needs some discussion with pincontrol driver folks on how to implement such a feature with generic pincontrol driver.Rajendra Nayak (4):
ARM: OMAP2+: hwmod: Remove unused_HWMOD_WAKEUP_ENABLEDflag
ARM: OMAP2+: hwmod: Cleanup sidle/mstandby programming
ARM: OMAP2+: hwmod: Always have OCP_SYSCONFIG.ENAWAKEUP enabled
ARM: OMAP2+: hwmod: Add a new flag to handle SIDLE in SWSUP only in
activeSantosh Shilimkar (4):
ARM: OMAP2+: hwmod-data: UART IP needs software control to manage
sidle modes
SERIAL: OMAP: Remove the slave idle handling from the driver
ARM: OMAP2+: serial: Remove the un-used slave idle hooks
ARM: OMAP2+: hwmod: Remove sysc slave idle and auto idle apisarch/arm/mach-omap2/omap_hwmod.c | 141 ++++---------------- arch/arm/mach-omap2/omap_hwmod.h | 13 +- arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c | 3 + arch/arm/mach-omap2/omap_hwmod_33xx_data.c | 6 + arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 4 + arch/arm/mach-omap2/omap_hwmod_44xx_data.c | 6 +- arch/arm/mach-omap2/serial.c | 31 ----- drivers/tty/serial/omap-serial.c | 23 ---- 8 files changed, 50 insertions(+), 177 deletions(-)
cover ARM; OMAP2+: hwmod and SERIAL: Remove sysc handling from driver
In reply to Santosh ShilimkarQuoted 3 lines · Santosh Shilimkar
OMAP UART IP needs manual idle modes based on functional state of the IP. Currently this is handled by the driver with function pointers implemented in platform code.
Up until now, the nightly test builds have included a load of test code for supporting DMA on OMAP serial - only the buggy transmit side which we've covered the reasons earlier why this can't work properly.
We've also covered why the ripping out of the DMA code from the serial driver, and then subsequent "cleanup" of the driver has resulted in it being impossible to resurect receive DMA support without reverting all those cleanups.
This patch set is yet again another nail in the coffin of any DMA support in the serial driver; it is removing the final bits of knowledge about how DMA support interacts with the idle support. Arguably, the previous cleanups already did that, but at least the hooks were still clearly visible as separate stand-alone entities and how only they were affected by DMA being enabled.
Therefore, tonight I am dropping and discarding what I have left over from my work on getting DMA support working with the OMAP serial driver again from the nightly test builds and my git tree, and I intend no further involvement with this.
cover ARM; OMAP2+: hwmod and SERIAL: Remove sysc handling from driver
Quoted 14 lines · Russell King - ARM Linux
Quoted 3 lines · Santosh Shilimkar
OMAP UART IP needs manual idle modes based on functional state of the IP. Currently this is handled by the driver with function pointers implemented in platform code.
Up until now, the nightly test builds have included a load of test code for supporting DMA on OMAP serial - only the buggy transmit side which we've covered the reasons earlier why this can't work properly.
We've also covered why the ripping out of the DMA code from the serial driver, and then subsequent "cleanup" of the driver has resulted in it being impossible to resurect receive DMA support without reverting all those cleanups.
Quoted 7 lines
This patch set is yet again another nail in the coffin of any DMA support in the serial driver; it is removing the final bits of knowledge about how DMA support interacts with the idle support. Arguably, the previous cleanups already did that, but at least the hooks were still clearly visible as separate stand-alone entities and how only they were affected by DMA being enabled.
Actually the clean-up will remove the serial driver dependency with idle handling. Infact DMA support need not care about idle handling anymore.
Quoted 5 lines
Therefore, tonight I am dropping and discarding what I have left over from my work on getting DMA support working with the OMAP serial driver again from the nightly test builds and my git tree, and I intend no further involvement with this.
Please please don't do that. We were at a point where we are unable to use UART has just simple console with DT without the $subject series. We can help you if some re-basing is needed for your patches because of the $subject series.
Sorry for another series getting in between your work but this one was unavoidable due to already broken support.
Regards,
Santosh
cover ARM; OMAP2+: hwmod and SERIAL: Remove sysc handling from driver
Quoted 3 lines · Santosh Shilimkar
Actually the clean-up will remove the serial driver dependency with idle handling. Infact DMA support need not care about idle handling anymore.
How is that so? Looking back at the driver source when it did have full DMA support shows that the handling of force idle state is different between PIO and DMA modes.
For example, for transmit (which is the only case I had taken the time to properly understand before the DMA code was unceremoniously ripped out):
- On DMA transmit, the noidle setting is cleared. runtime PM status is put.
- If we switch from DMA to PIO transmit, the noidle setting it set. runtime PM status is still put.
- When stopping transmit, if we aren't using DMA, idle is forced.
- In the runtime suspend, if we're using DMA and the i291 errata is in effect, then idle state is forced
- In the runtime resume, if we're using DMA and the i291 errata is in effect, idle state is cleared.
See - that information has been lost through ripping out the DMA code and then subsequently cleaning up the code to make these things "invisible". And now that you've lifted the forceidle/noidle functions out of the driver, there's now even less clue about how to preserve the above behaviour.
Quoted 9 lines
Quoted 5 lines
Therefore, tonight I am dropping and discarding what I have left over from my work on getting DMA support working with the OMAP serial driver again from the nightly test builds and my git tree, and I intend no further involvement with this.
Please please don't do that. We were at a point where we are unable to use UART has just simple console with DT without the $subject series. We can help you if some re-basing is needed for your patches because of the $subject series.
Actually, I've already dropped the TX DMA stuff out a while back when it became (a) just too painful to keep porting the thing forward and (b) it doesn't work properly anyway. It's last update was back in October, and was based on v3.6 because it already became impossible to bring it forward across the utter buggeration of the OMAP serial driver.
(That explains why I only ever pulled forward two patches - those which add the hooks into the serial core layer and into the OMAP serial driver to cleanly allocate a DMA-able transmit buffer, leaving the rest of the transmit DMA code to rot.)
cover ARM; OMAP2+: hwmod and SERIAL: Remove sysc handling from driver
Quoted 22 lines · Russell King - ARM Linux
Quoted 3 lines · Santosh Shilimkar
Actually the clean-up will remove the serial driver dependency with idle handling. Infact DMA support need not care about idle handling anymore.
How is that so? Looking back at the driver source when it did have full DMA support shows that the handling of force idle state is different between PIO and DMA modes.
For example, for transmit (which is the only case I had taken the time to properly understand before the DMA code was unceremoniously ripped out):
- On DMA transmit, the noidle setting is cleared. runtime PM status is put.
- If we switch from DMA to PIO transmit, the noidle setting it set. runtime PM status is still put.
- When stopping transmit, if we aren't using DMA, idle is forced.
- In the runtime suspend, if we're using DMA and the i291 errata is in effect, then idle state is forced
- In the runtime resume, if we're using DMA and the i291 errata is in effect, idle state is cleared.
Quoted 5 lines
See - that information has been lost through ripping out the DMA code and then subsequently cleaning up the code to make these things "invisible". And now that you've lifted the forceidle/noidle functions out of the driver, there's now even less clue about how to preserve the above behaviour.
I looked at the history based on above and indeed the i291 DMA
information got lost as part of cleanup. The UART DMA had a different requirement though the DMA errata is applicable to only OMAP3 devices and got fixed in subsequent OMAP based devices.
So perhaps we can make dma use conditional based on devices *when* we add the tx DMA support. And the errata information flag can be passed from DT files.
Quoted 16 lines
Quoted 9 lines
Quoted 5 lines
Therefore, tonight I am dropping and discarding what I have left over from my work on getting DMA support working with the OMAP serial driver again from the nightly test builds and my git tree, and I intend no further involvement with this.
Please please don't do that. We were at a point where we are unable to use UART has just simple console with DT without the $subject series. We can help you if some re-basing is needed for your patches because of the $subject series.
Actually, I've already dropped the TX DMA stuff out a while back when it became (a) just too painful to keep porting the thing forward and (b) it doesn't work properly anyway. It's last update was back in October, and was based on v3.6 because it already became impossible to bring it forward across the utter buggeration of the OMAP serial driver.
Quoted 5 lines
(That explains why I only ever pulled forward two patches - those which add the hooks into the serial core layer and into the OMAP serial driver to cleanly allocate a DMA-able transmit buffer, leaving the rest of the transmit DMA code to rot.)
Thanks for the information.
Regards,
Santosh