EXYNOS: Correct ordering of SPL machine_params
Subsystems (2)
PATCH 1/1 EXYNOS: Correct ordering of SPL machine_params
From: Simon Glass <[email protected]>
The mem_manuf is not in the correct order according to the string table. This causes cros_bundle_firmware to get the BL2 settings in the wrong order. This patch fixes the same.
--- arch/arm/include/asm/arch-exynos/spl.h | 3 ++- 1 files changed, 2 insertions(+), 1 deletions(-)
arch/arm/include/asm/arch-exynos/spl.h +2 -1
@@ -78,11 +78,12 @@ struct spl_machine_param {*/ u32 uboot_size;enum boot_mode boot_source;/* Boot device */ -enum mem_manuf mem_manuf;/* Memory Manufacturer */ unsigned frequency_mhz;/* Frequency of memory in MHz */ unsigned arm_freq_mhz;/* ARM Frequency in MHz */ u32 serial_base;/* Serial base address */ u32 i2c_base;/* i2c base address */ +u32 board_rev_gpios;/* Board revision GPIOs */ +enum mem_manuf mem_manuf;/* Memory Manufacturer */ } __attribute__((__packed__));#endif
Signature · 1 line
1.7.4.4
PATCH 1/1 EXYNOS: Correct ordering of SPL machine_params
Quoted 8 lines · Rajeshwari Shinde
From: Simon Glass <[email protected]>
The
mem_manufis not in the correct order according to the string table. This causescros_bundle_firmwareto get the BL2 settings in the wrong order. This patch fixes the same.Signed-off-by Simon Glass <[email protected]>Signed-off-by Rajeshwari Shinde <[email protected]>
Quoted 25 lines
--- arch/arm/include/asm/arch-exynos/spl.h | 3 ++- 1 files changed, 2 insertions(+), 1 deletions(-)arch/arm/include/asm/arch-exynos/spl.h +2
-2@@ -78,11 +78,12 @@ struct spl_machine_param {*/ u32 uboot_size;enum boot_mode boot_source;/* Boot device */ -enum mem_manuf mem_manuf;/* Memory Manufacturer */ unsigned frequency_mhz;/* Frequency of memory in MHz */ unsigned arm_freq_mhz;/* ARM Frequency in MHz */ u32 serial_base;/* Serial base address */ u32 i2c_base;/* i2c base address */ +u32 board_rev_gpios;/* Board revision GPIOs */ +enum mem_manuf mem_manuf;/* Memory Manufacturer */ } __attribute__((__packed__));#endif --1.7.4.4
PATCH 1/1 EXYNOS: Correct ordering of SPL machine_params
In reply to Rajeshwari ShindeQuoted 21 lines · Rajeshwari Shinde
From: Simon Glass <[email protected]>
The
mem_manufis not in the correct order according to the string table. This causescros_bundle_firmwareto get the BL2 settings in the wrong order. This patch fixes the same.Signed-off-by Simon Glass <[email protected]>Signed-off-by Rajeshwari Shinde <[email protected]>--- arch/arm/include/asm/arch-exynos/spl.h | 3 ++- 1 files changed, 2 insertions(+), 1 deletions(-)arch/arm/include/asm/arch-exynos/spl.h +0
-0@@ -78,11 +78,12 @@ struct spl_machine_param {*/ u32 uboot_size;enum boot_mode boot_source;/* Boot device */
arch/arm/include/asm/arch-exynos/spl.h struct spl_machine_param { · line 89
Quoted 10 lines
arch/arm/include/asm/arch-exynos/spl.h +2
-1-enum mem_manuf mem_manuf;/* Memory Manufacturer */ unsigned frequency_mhz;/* Frequency of memory in MHz */ unsigned arm_freq_mhz;/* ARM Frequency in MHz */ u32 serial_base;/* Serial base address */ u32 i2c_base;/* i2c base address */ +u32 board_rev_gpios;/* Board revision GPIOs */ +enum mem_manuf mem_manuf;/* Memory Manufacturer */ } __attribute__((__packed__));#endif
applied to u-boot-samsung.
Thanks,
Minkyu Kang.