mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
Subsystems (2)
Fabio Estevam
reviewerPATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
From: Fabio Estevam <[email protected]>
Currently the following kernel hang happens when loading a 2.6.35 kernel from Freeescale on a mx28evk board:
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registeredmxs_cpu_init: cpufreq init finished
...
Loading the same kernel using the bootlets from the imx-bootlets-src-10.12.01 package, the hang does not occur.
Comparing the DDR2 initialization from the bootlets code against the U-boot one, we can notice some mismatches, and after applying the same initialization into U-boot the 2.6.35 kernel can boot normally.
Also tested with 'mtest' command, which runs succesfully.
---
Changes since v1:
- Fix tabs/space confusion and only show the real context changes
arch/arm/cpu/arm926ejs/mxs/spl_mem_init.c | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-)
arch/arm/cpu/arm926ejs/mxs/spl_mem_init.c +9 -9
@@ -45,17 +45,17 @@ static uint32_t dram_vals[] = {0x00000000 ,0x00000000 ,0x00010101 ,0x01010101 ,0x000f0f01 ,0x0f02020a ,0x00000000 ,0x00010101 ,0x00000100 ,0x00000100 ,0x00000000 ,0x00000002 , -0x01010000 ,0x05060302 ,0x06005003 ,0x0a0000c8 , -0x02009c40 ,0x0000030c ,0x0036a609 ,0x031a0612 , +0x01010000 ,0x07080403 ,0x06005003 ,0x0a0000c8 , +0x02009c40 ,0x0002030c ,0x0036a609 ,0x031a0612 ,0x02030202 ,0x00c8001c ,0x00000000 ,0x00000000 ,0x00012100 ,0xffff0303 ,0x00012100 ,0xffff0303 ,0x00012100 ,0xffff0303 ,0x00012100 ,0xffff0303 ,0x00000003 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000612 ,0x01000F02 , -0x06120612 ,0x00000200 ,0x00020007 ,0xf5014b27 , -0xf5014b27 ,0xf5014b27 ,0xf5014b27 ,0x07000300 , -0x07000300 ,0x07000300 ,0x07000300 ,0x00000006 , +0x06120612 ,0x00000200 ,0x00020007 ,0xf4004a27 , +0xf4004a27 ,0xf4004a27 ,0xf4004a27 ,0x07000300 , +0x07000300 ,0x07400300 ,0x07400300 ,0x00000005 ,0x00000000 ,0x00000000 ,0x01000000 ,0x01020408 ,0x08040201 ,0x000f1133 ,0x00000000 ,0x00001f04 , 0x00001f04, 0x00001f04, 0x00001f04, 0x00001f04,
@@ -76,14 +76,14 @@ static uint32_t dram_vals[] = {0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 , -0x00000000 ,0x00000000 ,0x00010000 ,0x00020304 , -0x00000004 ,0x00000000 ,0x00000000 ,0x00000000 , +0x00000000 ,0x00000000 ,0x00010000 ,0x00030404 , +0x00000003 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x01010000 ,0x01000000 ,0x03030000 ,0x00010303 ,0x01020202 ,0x00000000 ,0x02040303 ,0x21002103 ,0x00061200 , -0x06120612 ,0x04320432 ,0x04320432 ,0x00040004 , +0x06120612 ,0x04420442 ,0x04420442 ,0x00040004 ,0x00040004 ,0x00000000 ,0x00000000 ,0x00000000 , -0x00000000 ,0x00010001 +0x00000000 ,0xffffffff /* * i.MX23 DDR at 133MHz
Signature · 1 line
1.7.9.5
PATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
Quoted 16 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
Currently the following kernel hang happens when loading a 2.6.35 kernel from Freeescale on a mx28evk board:
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registeredmxs_cpu_init: cpufreq init finished
...Loading the same kernel using the bootlets from the imx-bootlets-src-10.12.01 package, the hang does not occur.
Quoted 7 lines
Comparing the DDR2 initialization from the bootlets code against the U-boot one, we can notice some mismatches, and after applying the same initialization into U-boot the 2.6.35 kernel can boot normally.
Also tested with 'mtest' command, which runs succesfully.
Signed-off-by Fabio Estevam <[email protected]>
Signature · 3 lines
Otavio Salvador O.S. Systems E-mail: otavio at ossystems.com.br http://www.ossystems.com.br Mobile: +55 53 9981-7854 http://projetos.ossystems.com.br
PATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
Dear Otavio Salvador,
Quoted 21 lines · Fabio Estevam
Quoted 20 lines
From: Fabio Estevam <[email protected]>
Currently the following kernel hang happens when loading a 2.6.35 kernel from Freeescale on a mx28evk board:
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registeredmxs_cpu_init: cpufreq init finished
...Loading the same kernel using the bootlets from the imx-bootlets-src-10.12.01 package, the hang does not occur.
Comparing the DDR2 initialization from the bootlets code against the U-boot one, we can notice some mismatches, and after applying the same initialization into U-boot the 2.6.35 kernel can boot normally.
Quoted 5 lines
Quoted 3 lines
Also tested with 'mtest' command, which runs succesfully.
Signed-off-by Fabio Estevam <[email protected]>Acked-by Otavio Salvador <[email protected]>
Otavio, did you review the changes done in this patch ?
Best regards,
Marek Vasut
PATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
Quoted 23 lines · Marek Vasut
Dear Otavio Salvador,
Quoted 21 lines · Fabio Estevam
Quoted 20 lines
From: Fabio Estevam <[email protected]>
Currently the following kernel hang happens when loading a 2.6.35 kernel from Freeescale on a mx28evk board:
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registeredmxs_cpu_init: cpufreq init finished
...Loading the same kernel using the bootlets from the imx-bootlets-src-10.12.01 package, the hang does not occur.
Comparing the DDR2 initialization from the bootlets code against the U-boot one, we can notice some mismatches, and after applying the same initialization into U-boot the 2.6.35 kernel can boot normally.
Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
Also tested with 'mtest' command, which runs succesfully.
Signed-off-by Fabio Estevam <[email protected]>Acked-by Otavio Salvador <[email protected]>Otavio, did you review the changes done in this patch ?
This is the setup used in FSL U-Boot and it fixes 2.6.35.3 cpufreq kernel hang; it is good enough for me to accept it. If you care enough, go ahead and check every change bit.
Signature · 3 lines
Otavio Salvador O.S. Systems E-mail: otavio at ossystems.com.br http://www.ossystems.com.br Mobile: +55 53 9981-7854 http://projetos.ossystems.com.br
PATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
Dear Otavio Salvador,
Quoted 28 lines · Marek Vasut
Quoted 27 lines
Dear Otavio Salvador,
Quoted 25 lines · Fabio Estevam
Quoted 23 lines
From: Fabio Estevam <[email protected]>
Currently the following kernel hang happens when loading a 2.6.35 kernel from Freeescale on a mx28evk board:
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registeredmxs_cpu_init: cpufreq init finished
...Loading the same kernel using the bootlets from the imx-bootlets-src-10.12.01 package, the hang does not occur.
Comparing the DDR2 initialization from the bootlets code against the U-boot one, we can notice some mismatches, and after applying the same initialization into U-boot the 2.6.35 kernel can boot normally.
Also tested with 'mtest' command, which runs succesfully.
Signed-off-by Fabio Estevam <[email protected]>
Quoted 7 lines
Quoted 3 lines
Quoted 1 line
Acked-by Otavio Salvador <[email protected]>Otavio, did you review the changes done in this patch ?
This is the setup used in FSL U-Boot and it fixes 2.6.35.3 cpufreq kernel hang; it is good enough for me to accept it. If you care enough, go ahead and check every change bit.
That is indeed the plan, I will Ack this after I am done with it. It will still make it for .04, dont worry.
You should not Ack patches you did not even test nor validate, since the value of your Ack is declining.
Best regards,
Marek Vasut
PATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
Quoted 38 lines · Marek Vasut
Dear Otavio Salvador,
Quoted 28 lines · Marek Vasut
Quoted 27 lines
Dear Otavio Salvador,
Quoted 25 lines · Fabio Estevam
Quoted 23 lines
From: Fabio Estevam <[email protected]>
Currently the following kernel hang happens when loading a 2.6.35 kernel from Freeescale on a mx28evk board:
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registeredmxs_cpu_init: cpufreq init finished
...Loading the same kernel using the bootlets from the imx-bootlets-src-10.12.01 package, the hang does not occur.
Comparing the DDR2 initialization from the bootlets code against the U-boot one, we can notice some mismatches, and after applying the same initialization into U-boot the 2.6.35 kernel can boot normally.
Also tested with 'mtest' command, which runs succesfully.
Signed-off-by Fabio Estevam <[email protected]>Quoted 7 lines
Quoted 3 lines
Quoted 1 line
Acked-by Otavio Salvador <[email protected]>Otavio, did you review the changes done in this patch ?
This is the setup used in FSL U-Boot and it fixes 2.6.35.3 cpufreq kernel hang; it is good enough for me to accept it. If you care enough, go ahead and check every change bit.
Quoted 5 lines
That is indeed the plan, I will Ack this after I am done with it. It will still make it for .04, dont worry.
You should not Ack patches you did not even test nor validate, since the value of your Ack is declining.
Are you sure you read my comment?
... it fixes 2.6.35.3 cpufreq kernel hang; ...
Regards,
--
Otavio Salvador O.S. Systems
E-mail: otavio at ossystems.com.br http://www.ossystems.com.br
Mobile: +55 53 9981-7854 http://projetos.ossystems.com.br
PATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
Dear Otavio Salvador,
Quoted 7 lines · Marek Vasut
Quoted 6 lines
Dear Otavio Salvador,
Quoted 4 lines · Marek Vasut
Quoted 3 lines
Dear Otavio Salvador,
Quoted 1 line
On Thu, Feb 28, 2013 at 7:59 PM, Fabio Estevam <[email protected]>
Quoted 36 lines · wrote:
Quoted 36 lines
Quoted 25 lines
Quoted 25 lines
Quoted 25 lines
Quoted 24 lines
From: Fabio Estevam <[email protected]>
Currently the following kernel hang happens when loading a 2.6.35 kernel from Freeescale on a mx28evk board:
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registeredmxs_cpu_init: cpufreq init finished
...Loading the same kernel using the bootlets from the imx-bootlets-src-10.12.01 package, the hang does not occur.
Comparing the DDR2 initialization from the bootlets code against the U-boot one, we can notice some mismatches, and after applying the same initialization into U-boot the 2.6.35 kernel can boot normally.
Also tested with 'mtest' command, which runs succesfully.
Signed-off-by Fabio Estevam <[email protected]>Quoted 7 lines
Quoted 3 lines
Quoted 1 line
Acked-by Otavio Salvador <[email protected]>Otavio, did you review the changes done in this patch ?
This is the setup used in FSL U-Boot and it fixes 2.6.35.3 cpufreq kernel hang; it is good enough for me to accept it. If you care enough, go ahead and check every change bit.
That is indeed the plan, I will Ack this after I am done with it. It will still make it for .04, dont worry.
Quoted 6 lines
Quoted 2 lines
You should not Ack patches you did not even test nor validate, since the value of your Ack is declining.
Are you sure you read my comment?
... it fixes 2.6.35.3 cpufreq kernel hang; ...
Yes, I did read it.
Best regards,
Marek Vasut
PATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
In reply to Fabio EstevamQuoted 5 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
Currently the following kernel hang happens when loading a 2.6.35 kernel from Freeescale on a mx28evk board:
Quoted 8 lines
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registeredmxs_cpu_init: cpufreq init finished
...
Hi all,
Quoted 53 lines
Loading the same kernel using the bootlets from the imx-bootlets-src-10.12.01 package, the hang does not occur.
Comparing the DDR2 initialization from the bootlets code against the U-boot one, we can notice some mismatches, and after applying the same initialization into U-boot the 2.6.35 kernel can boot normally.
Also tested with 'mtest' command, which runs succesfully.
Signed-off-by Fabio Estevam <[email protected]>---
Changes since v1:
- Fix tabs/space confusion and only show the real context changesarch/arm/cpu/arm926ejs/mxs/spl_mem_init.c | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-)arch/arm/cpu/arm926ejs/mxs/spl_mem_init.c +7
-7@@ -45,17 +45,17 @@ static uint32_t dram_vals[] = {0x00000000 ,0x00000000 ,0x00010101 ,0x01010101 ,0x000f0f01 ,0x0f02020a ,0x00000000 ,0x00010101 ,0x00000100 ,0x00000100 ,0x00000000 ,0x00000002 , -0x01010000 ,0x05060302 ,0x06005003 ,0x0a0000c8 , -0x02009c40 ,0x0000030c ,0x0036a609 ,0x031a0612 , +0x01010000 ,0x07080403 ,0x06005003 ,0x0a0000c8 , +0x02009c40 ,0x0002030c ,0x0036a609 ,0x031a0612 ,0x02030202 ,0x00c8001c ,0x00000000 ,0x00000000 ,0x00012100 ,0xffff0303 ,0x00012100 ,0xffff0303 ,0x00012100 ,0xffff0303 ,0x00012100 ,0xffff0303 ,0x00000003 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000612 ,0x01000F02 , -0x06120612 ,0x00000200 ,0x00020007 ,0xf5014b27 , -0xf5014b27 ,0xf5014b27 ,0xf5014b27 ,0x07000300 , -0x07000300 ,0x07000300 ,0x07000300 ,0x00000006 , +0x06120612 ,0x00000200 ,0x00020007 ,0xf4004a27 , +0xf4004a27 ,0xf4004a27 ,0xf4004a27 ,0x07000300 , +0x07000300 ,0x07400300 ,0x07400300 ,0x00000005 ,0x00000000 ,0x00000000 ,0x01000000 ,0x01020408 ,0x08040201 ,0x000f1133 ,0x00000000 ,0x00001f04 , 0x00001f04, 0x00001f04, 0x00001f04, 0x00001f04,@@ -76,14 +76,14 @@ static uint32_t dram_vals[] = {0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 , -0x00000000 ,0x00000000 ,0x00010000 ,0x00020304 , -0x00000004 ,0x00000000 ,0x00000000 ,0x00000000 , +0x00000000 ,0x00000000 ,0x00010000 ,0x00030404 , +0x00000003 ,0x00000000 ,0x00000000 ,0x00000000 , 0x00000000, 0x00000000, 0x00000000, 0x01010000,
arch/arm/cpu/arm926ejs/mxs/spl_mem_init.c static uint32_t dram_vals[] = { · line 89
Quoted 10 lines
arch/arm/cpu/arm926ejs/mxs/spl_mem_init.c +2
-20x01000000 ,0x03030000 ,0x00010303 ,0x01020202 ,0x00000000 ,0x02040303 ,0x21002103 ,0x00061200 , -0x06120612 ,0x04320432 ,0x04320432 ,0x00040004 , +0x06120612 ,0x04420442 ,0x04420442 ,0x00040004 ,0x00040004 ,0x00000000 ,0x00000000 ,0x00000000 , -0x00000000 ,0x00010001 +0x00000000 ,0xffffffff /* * i.MX23 DDR at 133MHz
Apart of the fact that fixes booting old kernel, these changes affects all mx28 boards, not only mx28evk. Can we have a description about which changes are done and why they are required ?
Else to be accepted we need at least a Tested-vy for all boards using it.
Regards,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
Fabio Estevam
reviewerPATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
Hi Stefano,
Quoted 5 lines · Stefano Babic
Apart of the fact that fixes booting old kernel, these changes affects all mx28 boards, not only mx28evk. Can we have a description about which changes are done and why they are required ?
Else to be accepted we need at least a Tested-vy for all boards using it.
Yes, having a Tested-by would be really nice.
Currently we have the following mx28 based boards that still needs to be tested:
apx4devkit, m28evk and sc_sps_1.
Veli-Pekka/Marek,
Could you please try this patch on your systems?
About the description of the changes: I haven't really gone deep into the path of comparing all the bits that changed. I simply took a working DDR init script for mx28evk from imx bootlets code and used it.
Moving forward, I think we should split the DDR init per board instead of a global init.
Regards,
Fabio Estevam
Fabio Estevam
reviewerPATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
Lauri,
Quoted 12 lines · Fabio Estevam
Hi Stefano,
Quoted 5 lines · Stefano Babic
Apart of the fact that fixes booting old kernel, these changes affects all mx28 boards, not only mx28evk. Can we have a description about which changes are done and why they are required ?
Else to be accepted we need at least a Tested-vy for all boards using it.
Yes, having a Tested-by would be really nice.
Quoted 7 lines
Currently we have the following mx28 based boards that still needs to be tested:
apx4devkit, m28evk and
sc_sps_1.Veli-Pekka/Marek,
Could you please try this patch on your systems?
Veli-Pekka's email bounced. Would you have a chance to test it?
Thanks,
Fabio Estevam
PATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
Hi,
Quoted 17 lines · Fabio Estevam
Lauri,
Quoted 14 lines · Fabio Estevam
Hi Stefano,
Quoted 5 lines · Stefano Babic
Apart of the fact that fixes booting old kernel, these changes affects all mx28 boards, not only mx28evk. Can we have a description about which changes are done and why they are required ?
Else to be accepted we need at least a Tested-vy for all boards using it.
Yes, having a Tested-by would be really nice.
Currently we have the following mx28 based boards that still needs to be tested:
Quoted 7 lines
Quoted 5 lines
apx4devkit, m28evk and
sc_sps_1.Veli-Pekka/Marek,
Could you please try this patch on your systems?
Veli-Pekka's email bounced. Would you have a chance to test it?
Yes, I'll test the patch.
Lauri
PATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
Quoted 31 lines · Lauri Hintsala
Hi,
Quoted 27 lines · Fabio Estevam
Lauri,
Quoted 22 lines · Fabio Estevam
Hi Stefano,
Quoted 6 lines · Stefano Babic
Apart of the fact that fixes booting old kernel, these changes affects all mx28 boards, not only mx28evk. Can we have a description about which changes are done and why they are required ?
Else to be accepted we need at least a Tested-vy for all boards using it.
Yes, having a Tested-by would be really nice.
Currently we have the following mx28 based boards that still needs to be tested:
apx4devkit, m28evk and
sc_sps_1.Veli-Pekka/Marek,
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
Could you please try this patch on your systems?
Veli-Pekka's email bounced. Would you have a chance to test it?
Yes, I'll test the patch.
Lauri, did you give this patch?
Signature · 3 lines
Otavio Salvador O.S. Systems E-mail: otavio at ossystems.com.br http://www.ossystems.com.br Mobile: +55 53 9981-7854 http://projetos.ossystems.com.br
PATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
In reply to Stefano BabicDear Stefano Babic,
Quoted 90 lines · Fabio Estevam
Quoted 5 lines
From: Fabio Estevam <[email protected]>
Currently the following kernel hang happens when loading a 2.6.35 kernel from Freeescale on a mx28evk board:
Quoted 7 lines
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registeredmxs_cpu_init: cpufreq init finished
...Hi all,
Quoted 74 lines
Loading the same kernel using the bootlets from the imx-bootlets-src-10.12.01 package, the hang does not occur.
Comparing the DDR2 initialization from the bootlets code against the U-boot one, we can notice some mismatches, and after applying the same initialization into U-boot the 2.6.35 kernel can boot normally.
Also tested with 'mtest' command, which runs succesfully.
Signed-off-by Fabio Estevam <[email protected]>---
Changes since v1:
- Fix tabs/space confusion and only show the real context changesarch/arm/cpu/arm926ejs/mxs/spl_mem_init.c | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-)(quoted diff) +0
-0
b/arch/arm/cpu/arm926ejs/mxs/spl_mem_init.cindex f8392f6..2195dce 100644arch/arm/cpu/arm926ejs/mxs/spl_mem_init.c +8
-8@@ -45,17 +45,17 @@ static uint32_t dram_vals[] = {0x00000000 ,0x00000000 ,0x00010101 ,0x01010101 ,0x000f0f01 ,0x0f02020a ,0x00000000 ,0x00010101 ,0x00000100 ,0x00000100 ,0x00000000 ,0x00000002 , -0x01010000 ,0x05060302 ,0x06005003 ,0x0a0000c8 , -0x02009c40 ,0x0000030c ,0x0036a609 ,0x031a0612 , +0x01010000 ,0x07080403 ,0x06005003 ,0x0a0000c8 , +0x02009c40 ,0x0002030c ,0x0036a609 ,0x031a0612 ,0x02030202 ,0x00c8001c ,0x00000000 ,0x00000000 ,0x00012100 ,0xffff0303 ,0x00012100 ,0xffff0303 ,0x00012100 ,0xffff0303 ,0x00012100 ,0xffff0303 ,0x00000003 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000612 ,0x01000F02 , -0x06120612 ,0x00000200 ,0x00020007 ,0xf5014b27 , -0xf5014b27 ,0xf5014b27 ,0xf5014b27 ,0x07000300 , -0x07000300 ,0x07000300 ,0x07000300 ,0x00000006 , +0x06120612 ,0x00000200 ,0x00020007 ,0xf4004a27 , +0xf4004a27 ,0xf4004a27 ,0xf4004a27 ,0x07000300 , +0x07000300 ,0x07400300 ,0x07400300 ,0x00000005 ,0x00000000 ,0x00000000 ,0x01000000 ,0x01020408 ,0x08040201 ,0x000f1133 ,0x00000000 ,0x00001f04 , 0x00001f04, 0x00001f04, 0x00001f04, 0x00001f04,@@ -76,14 +76,14 @@ static uint32_t dram_vals[] = {0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 , -0x00000000 ,0x00000000 ,0x00010000 ,0x00020304 , -0x00000004 ,0x00000000 ,0x00000000 ,0x00000000 , +0x00000000 ,0x00000000 ,0x00010000 ,0x00030404 , +0x00000003 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x01010000 ,0x01000000 ,0x03030000 ,0x00010303 ,0x01020202 ,0x00000000 ,0x02040303 ,0x21002103 ,0x00061200 , - 0x06120612, 0x04320432, 0x04320432, 0x00040004, + 0x06120612, 0x04420442, 0x04420442, 0x00040004,arch/arm/cpu/arm926ejs/mxs/spl_mem_init.c +1
-10x00040004 ,0x00000000 ,0x00000000 ,0x00000000 , -0x00000000 ,0x00010001 +0x00000000 ,0xffffffff
Quoted 7 lines
Quoted 3 lines
/*
* i.MX23 DDR at 133MHz
Apart of the fact that fixes booting old kernel, these changes affects all mx28 boards, not only mx28evk. Can we have a description about which changes are done and why they are required ?
Please see [1] below, this describes the situation at hand perfectly :-)
Other than that, I tested it and see no issue.
Quoted 5 lines
Else to be accepted we need at least a Tested-vy for all boards using it.
Regards,
Stefano
[1] http://devopsreactions.tumblr.com/post/40166795163/when-you-review-
undocumented-code
PATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
Quoted 8 lines · Marek Vasut
Quoted 3 lines
Apart of the fact that fixes booting old kernel, these changes affects all mx28 boards, not only mx28evk. Can we have a description about which changes are done and why they are required ?
Please see [1] below, this describes the situation at hand perfectly :-)
Other than that, I tested it and see no issue.
Quoted 8 lines
Quoted 5 lines
Else to be accepted we need at least a Tested-vy for all boards using it.
Regards,
Stefano[1] http://devopsreactions.tumblr.com/post/40166795163/when-you-review-
undocumented-code
It is perfect for this sort of hexadecimal tables !
Regards,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
In reply to Fabio EstevamDear Fabio Estevam,
Quoted 16 lines
From: Fabio Estevam <[email protected]>
Currently the following kernel hang happens when loading a 2.6.35 kernel from Freeescale on a mx28evk board:
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registeredmxs_cpu_init: cpufreq init finished
...Loading the same kernel using the bootlets from the imx-bootlets-src-10.12.01 package, the hang does not occur.
Quoted 7 lines
Comparing the DDR2 initialization from the bootlets code against the U-boot one, we can notice some mismatches, and after applying the same initialization into U-boot the 2.6.35 kernel can boot normally.
Also tested with 'mtest' command, which runs succesfully.
Signed-off-by Fabio Estevam <[email protected]>
On M28EVK:
Best regards,
Marek Vasut
PATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
In reply to Fabio EstevamHi,
Quoted 5 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
Currently the following kernel hang happens when loading a 2.6.35 kernel from Freeescale on a mx28evk board:
Quoted 7 lines
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registeredmxs_cpu_init: cpufreq init finished
...
I tried to boot Freescale's 2.6.35.3 kernel on apx4devkit. The device is still freezing after mxs_cpu_init print.
Full logs:
U-Boot 2013.04-rc1-00002-g9659479 (Mar 19 2013 - 08:30:05)
CPU: Freescale i.MX28 rev1.2 at 454 MHz BOOT: SSP SD/MMC #0, 3V3 I2C: ready DRAM: 64 MiB NAND: 128 MiB MMC: MXS MMC: 0 In: serial Out: serial Err: serial Net: FEC Hit any key to stop autoboot: 0
1944456 bytes read in 754 ms (2.5 MiB/s)
## Booting kernel from Legacy Image at 41000000 ...
Image Name: Linux-2.6.35.3-01010-ge53a812
Created: 2013-03-19 6:31:40 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1944392 Bytes = 1.9 MiB
Load Address: 40008000
Entry Point: 40008000
Loading Kernel Image ... OKOK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.35.3-01010-ge53a812 (hintsla at bgtlh) (gcc version 4.3.4 (crosstool-NG-1.7.0) ) #32 Tue Mar 19 08:31:39 EET 2013
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Freescale MX28EVK board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=tty0 console=ttyAMA0,115200 consoleblank=0 ethaddr=00:07:80:01:66:db btaddr=00:07:80:01:67:0d wlanaddr=00:07:80:59:ef:64 root=/dev/mmcblk0p2 rootwait mtdparts=gpmi-nand:128k(bootstrap),1024k(boot),768k(env),-(root) rw PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 60880k/60880k available, 4656k reserved, 0K highmem Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xfde00000 - 0xffe00000 ( 32 MB)
vmalloc : 0xc4800000 - 0xf0000000 ( 696 MB)
lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc002d000 ( 148 kB)
.text : 0xc002d000 - 0xc03b8000 (3628 kB)
.data : 0xc03b8000 - 0xc03e4ba0 ( 179 kB)SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled. Verbose stalled-CPUs detection is disabled.
NR_IRQS:288
Console: colour dummy device 80x30
console [tty0] enabled
console [ttyAMA0] enabled
Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496)pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
regulator: vddd: 800 <--> 1575 mV at 1500 mV fast normal
regulator: vdddbo: 800 <--> 1575 mV fast normal
regulator: vdda: 1500 <--> 2275 mV at 1800 mV fast normal vddio = 3380000, val=10
regulator: vddio: 2880 <--> 3680 mV at 3380 mV fast normal
regulator: overall_current: fast normal
regulator: vbus5v:
regulator: mxs-duart-1: fast normal
regulator: mxs-bl-1: fast normal
regulator: mxs-i2c-1: fast normal
regulator: mmc_ssp-1: fast normal
regulator: mmc_ssp-2: fast normal
regulator: charger-1: fast normal
regulator: power-test-1: fast normal
regulator: cpufreq-1: fast normal
i.MX IRAM pool: 124 KB at 0xc4820000
Initializing GPMI pins
Initializing SSP2 pins
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Version 1.0.23.
IMX usb wakeup probe
usb DR wakeup device is registered
Switching to clocksource mxs clock source
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes) Switched to NOHz mode on CPU #0
TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registered
WARNING : No battery connected !
Aborting power driver initialization
mxs-battery: probe of mxs-battery.0 failed with error 1mxs_cpu_init: cpufreq init finished
And after that line the device is completely dead.
Lauri
Quoted 64 lines
Loading the same kernel using the bootlets from the imx-bootlets-src-10.12.01 package, the hang does not occur.
Comparing the DDR2 initialization from the bootlets code against the U-boot one, we can notice some mismatches, and after applying the same initialization into U-boot the 2.6.35 kernel can boot normally.
Also tested with 'mtest' command, which runs succesfully.
Signed-off-by Fabio Estevam <[email protected]>---
Changes since v1:
- Fix tabs/space confusion and only show the real context changesarch/arm/cpu/arm926ejs/mxs/spl_mem_init.c | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-)arch/arm/cpu/arm926ejs/mxs/spl_mem_init.c +9
-9@@ -45,17 +45,17 @@ static uint32_t dram_vals[] = {0x00000000 ,0x00000000 ,0x00010101 ,0x01010101 ,0x000f0f01 ,0x0f02020a ,0x00000000 ,0x00010101 ,0x00000100 ,0x00000100 ,0x00000000 ,0x00000002 , -0x01010000 ,0x05060302 ,0x06005003 ,0x0a0000c8 , -0x02009c40 ,0x0000030c ,0x0036a609 ,0x031a0612 , +0x01010000 ,0x07080403 ,0x06005003 ,0x0a0000c8 , +0x02009c40 ,0x0002030c ,0x0036a609 ,0x031a0612 ,0x02030202 ,0x00c8001c ,0x00000000 ,0x00000000 ,0x00012100 ,0xffff0303 ,0x00012100 ,0xffff0303 ,0x00012100 ,0xffff0303 ,0x00012100 ,0xffff0303 ,0x00000003 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000612 ,0x01000F02 , -0x06120612 ,0x00000200 ,0x00020007 ,0xf5014b27 , -0xf5014b27 ,0xf5014b27 ,0xf5014b27 ,0x07000300 , -0x07000300 ,0x07000300 ,0x07000300 ,0x00000006 , +0x06120612 ,0x00000200 ,0x00020007 ,0xf4004a27 , +0xf4004a27 ,0xf4004a27 ,0xf4004a27 ,0x07000300 , +0x07000300 ,0x07400300 ,0x07400300 ,0x00000005 ,0x00000000 ,0x00000000 ,0x01000000 ,0x01020408 ,0x08040201 ,0x000f1133 ,0x00000000 ,0x00001f04 , 0x00001f04, 0x00001f04, 0x00001f04, 0x00001f04,@@ -76,14 +76,14 @@ static uint32_t dram_vals[] = {0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 , -0x00000000 ,0x00000000 ,0x00010000 ,0x00020304 , -0x00000004 ,0x00000000 ,0x00000000 ,0x00000000 , +0x00000000 ,0x00000000 ,0x00010000 ,0x00030404 , +0x00000003 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x00000000 ,0x01010000 ,0x01000000 ,0x03030000 ,0x00010303 ,0x01020202 ,0x00000000 ,0x02040303 ,0x21002103 ,0x00061200 , -0x06120612 ,0x04320432 ,0x04320432 ,0x00040004 , +0x06120612 ,0x04420442 ,0x04420442 ,0x00040004 ,0x00040004 ,0x00000000 ,0x00000000 ,0x00000000 , -0x00000000 ,0x00010001 +0x00000000 ,0xffffffff /* * i.MX23 DDR at 133MHz
PATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
Quoted 144 lines · Lauri Hintsala
Hi,
Quoted 7 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
Currently the following kernel hang happens when loading a 2.6.35 kernel from
Freeescale on a mx28evk board:Quoted 7 lines
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registeredmxs_cpu_init: cpufreq init finished
...I tried to boot Freescale's 2.6.35.3 kernel on apx4devkit. The device is still freezing after
mxs_cpu_initprint.Full logs:
U-Boot 2013.04-rc1-00002-g9659479 (Mar 19 2013 - 08:30:05)
CPU: Freescale i.MX28 rev1.2 at 454 MHz BOOT: SSP SD/MMC #0, 3V3 I2C: ready DRAM: 64 MiB NAND: 128 MiB MMC: MXS MMC: 0 In: serial Out: serial Err: serial Net: FEC Hit any key to stop autoboot: 01944456 bytes read in 754 ms (2.5 MiB/s)
## Booting kernel from Legacy Image at 41000000 ...Image Name: Linux-2.6.35.3-01010-ge53a812 Created: 2013-03-19 6:31:40 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1944392 Bytes = 1.9 MiBLoad Address: 40008000
Entry Point: 40008000
Loading Kernel Image ... OK
OKStarting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.35.3-01010-ge53a812 (hintsla at bgtlh) (gcc version 4.3.4 (crosstool-NG-1.7.0) ) #32 Tue Mar 19 08:31:39 EET 2013
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Freescale MX28EVK board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=tty0 console=ttyAMA0,115200 consoleblank=0 ethaddr=00:07:80:01:66:db btaddr=00:07:80:01:67:0d wlanaddr=00:07:80:59:ef:64 root=/dev/mmcblk0p2 rootwait mtdparts=gpmi-nand:128k(bootstrap),1024k(boot),768k(env),-(root) rw PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 60880k/60880k available, 4656k reserved, 0K highmem Virtual kernel memory layout:vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xfde00000 - 0xffe00000 ( 32 MB) vmalloc : 0xc4800000 - 0xf0000000 ( 696 MB) lowmem : 0xc0000000 - 0xc4000000 ( 64 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .init : 0xc0008000 - 0xc002d000 ( 148 kB) .text : 0xc002d000 - 0xc03b8000 (3628 kB) .data : 0xc03b8000 - 0xc03e4ba0 ( 179 kB)SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled. Verbose stalled-CPUs detection is disabled.
NR_IRQS:288
Console: colour dummy device 80x30
console [tty0] enabled
console [ttyAMA0] enabled
Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496)pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
regulator: vddd: 800 <--> 1575 mV at 1500 mV fast normal
regulator: vdddbo: 800 <--> 1575 mV fast normal
regulator: vdda: 1500 <--> 2275 mV at 1800 mV fast normal vddio = 3380000, val=10
regulator: vddio: 2880 <--> 3680 mV at 3380 mV fast normal
regulator:overall_current: fast normal
regulator: vbus5v:
regulator: mxs-duart-1: fast normal
regulator: mxs-bl-1: fast normal
regulator: mxs-i2c-1: fast normal
regulator: mmc_ssp-1: fast normal
regulator: mmc_ssp-2: fast normal
regulator: charger-1: fast normal
regulator: power-test-1: fast normal
regulator: cpufreq-1: fast normal
i.MX IRAM pool: 124 KB at0xc4820000
Initializing GPMI pins
Initializing SSP2 pins
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Version 1.0.23.
IMX usb wakeup probe
usb DR wakeup device is registered
Switching to clocksource mxs clock source
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes) Switched to NOHz mode on CPU #0
TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registered
WARNING : No battery connected !
Aborting power driver initialization
mxs-battery: probe of mxs-battery.0 failed with error 1mxs_cpu_init: cpufreq init finished
Quoted 1 line
And after that line the device is completely dead.
Are you sure you booted it with the Fabio's patch applied; this is exactly how it behaves *without* it.
Signature · 3 lines
Otavio Salvador O.S. Systems E-mail: otavio at ossystems.com.br http://www.ossystems.com.br Mobile: +55 53 9981-7854 http://projetos.ossystems.com.br
PATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
Quoted 146 lines · Otavio Salvador
Quoted 144 lines · Lauri Hintsala
Hi,
Quoted 7 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
Currently the following kernel hang happens when loading a 2.6.35 kernel from
Freeescale on a mx28evk board:Quoted 7 lines
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registeredmxs_cpu_init: cpufreq init finished
...I tried to boot Freescale's 2.6.35.3 kernel on apx4devkit. The device is still freezing after
mxs_cpu_initprint.Full logs:
U-Boot 2013.04-rc1-00002-g9659479 (Mar 19 2013 - 08:30:05)
CPU: Freescale i.MX28 rev1.2 at 454 MHz BOOT: SSP SD/MMC #0, 3V3 I2C: ready DRAM: 64 MiB NAND: 128 MiB MMC: MXS MMC: 0 In: serial Out: serial Err: serial Net: FEC Hit any key to stop autoboot: 01944456 bytes read in 754 ms (2.5 MiB/s)
## Booting kernel from Legacy Image at 41000000 ...Image Name: Linux-2.6.35.3-01010-ge53a812 Created: 2013-03-19 6:31:40 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1944392 Bytes = 1.9 MiB Load Address: 40008000 Entry Point: 40008000 Loading Kernel Image ... OKOK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.35.3-01010-ge53a812 (hintsla at bgtlh) (gcc version 4.3.4 (crosstool-NG-1.7.0) ) #32 Tue Mar 19 08:31:39 EET 2013
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Freescale MX28EVK board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=tty0 console=ttyAMA0,115200 consoleblank=0 ethaddr=00:07:80:01:66:db btaddr=00:07:80:01:67:0d wlanaddr=00:07:80:59:ef:64 root=/dev/mmcblk0p2 rootwait mtdparts=gpmi-nand:128k(bootstrap),1024k(boot),768k(env),-(root) rw PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 60880k/60880k available, 4656k reserved, 0K highmem Virtual kernel memory layout:vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xfde00000 - 0xffe00000 ( 32 MB) vmalloc : 0xc4800000 - 0xf0000000 ( 696 MB) lowmem : 0xc0000000 - 0xc4000000 ( 64 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .init : 0xc0008000 - 0xc002d000 ( 148 kB) .text : 0xc002d000 - 0xc03b8000 (3628 kB) .data : 0xc03b8000 - 0xc03e4ba0 ( 179 kB)SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled. Verbose stalled-CPUs detection is disabled.
NR_IRQS:288
Console: colour dummy device 80x30
console [tty0] enabled
console [ttyAMA0] enabled
Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496)pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
regulator: vddd: 800 <--> 1575 mV at 1500 mV fast normal
regulator: vdddbo: 800 <--> 1575 mV fast normal
regulator: vdda: 1500 <--> 2275 mV at 1800 mV fast normal vddio = 3380000, val=10
regulator: vddio: 2880 <--> 3680 mV at 3380 mV fast normal
regulator:overall_current: fast normal
regulator: vbus5v:
regulator: mxs-duart-1: fast normal
regulator: mxs-bl-1: fast normal
regulator: mxs-i2c-1: fast normal
regulator: mmc_ssp-1: fast normal
regulator: mmc_ssp-2: fast normal
regulator: charger-1: fast normal
regulator: power-test-1: fast normal
regulator: cpufreq-1: fast normal
i.MX IRAM pool: 124 KB at0xc4820000
Initializing GPMI pins
Initializing SSP2 pins
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Version 1.0.23.
IMX usb wakeup probe
usb DR wakeup device is registered
Switching to clocksource mxs clock source
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes) Switched to NOHz mode on CPU #0
TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registered
WARNING : No battery connected !
Aborting power driver initialization
mxs-battery: probe of mxs-battery.0 failed with error 1mxs_cpu_init: cpufreq init finished
Quoted 4 lines
Quoted 1 line
And after that line the device is completely dead.
Are you sure you booted it with the Fabio's patch applied; this is exactly how it behaves *without* it.
Yes, I am. I booted up U-Boot version "2013.04-rc1-00002-g9659479 (Mar 19 2013 - 08:30:05)" and my git log says:
$ git log --oneline -3 9659479 (HEAD) mxs: spl_mem_init: Align DDR2 init with FSL bootlets source 7ddcf4c ARM: mxs: disable battery charger circuit 2536850 (tag: v2013.04-rc1) Prepare v2013.04-rc1
Battery charger patch is very simple and it shouldn't affect to this problem any way:
arch/arm/cpu/arm926ejs/mxs/spl_power_init.c +0 -0
@@ -918,6 +918,9 @@ void mxs_power_init(void) writel(POWER_5VCTRL_PWDN_5VBRNOUT,
&power_regs->hw_power_5vctrl_set);
+ /* Disable battery charger circuit */
+ power_regs->hw_power_charge_set = POWER_CHARGE_PWD_BATTCHRG;
+
early_delay(1000);
}
Lauri
Fabio Estevam
reviewerPATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
Hi Lauri,
Quoted 6 lines · Lauri Hintsala
Battery charger patch is very simple and it shouldn't affect to this problem any way:
arch/arm/cpu/arm926ejs/mxs/spl_power_init.c void mxs_power_init(void) · line 925
Quoted 8 lines
arch/arm/cpu/arm926ejs/mxs/spl_power_init.c +3
-0@@ -918,6 +918,9 @@ void mxs_power_init(void)writel (POWER_5VCTRL_PWDN_5VBRNOUT , &power_regs->hw_power_5vctrl_set); +/* Disable battery charger circuit */ + power_regs->hw_power_charge_set =POWER_CHARGE_PWD_BATTCHRG ; +early_delay (1000 );
What about this change? Do you plan to submit this as a patch?
Fabio Estevam
reviewerPATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
In reply to Lauri HintsalaQuoted 2 lines · Lauri Hintsala
I tried to boot Freescale's 2.6.35.3 kernel on apx4devkit. The device is still freezing after
mxs_cpu_initprint.
Are you able to boot 3.8?
I assume that the freeze still happened without this patch, right?
PATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
Quoted 7 lines · Fabio Estevam
Quoted 2 lines · Lauri Hintsala
I tried to boot Freescale's 2.6.35.3 kernel on apx4devkit. The device is still freezing after
mxs_cpu_initprint.Are you able to boot 3.8?
I booted up to 3.2.
Quoted 1 line
I assume that the freeze still happened without this patch, right?
The freeze happens with and without this patch if I use 2.6.35.3 kernel from Freescale.
Lauri
Fabio Estevam
reviewerPATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
Quoted 7 lines · Lauri Hintsala
Quoted 1 line
Are you able to boot 3.8?
I booted up to 3.2.
Quoted 5 lines
Quoted 1 line
I assume that the freeze still happened without this patch, right?
The freeze happens with and without this patch if I use 2.6.35.3 kernel from Freescale.
Thanks for testing, Lauri.
I think the issue with cpufreq still happens for you on 2.6.35 because you may use a different DDR model/topology than the one in mx28evk.
Stefano,
Since this patch does not cause any problems and does fix the 2.6.35 boot on mx28evk, is it possible to apply it for 2013.04?
Thanks,
Fabio Estevam
PATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
Quoted 18 lines · Fabio Estevam
Quoted 7 lines · Lauri Hintsala
Quoted 1 line
Are you able to boot 3.8?
I booted up to 3.2.
Quoted 5 lines
Quoted 1 line
I assume that the freeze still happened without this patch, right?
The freeze happens with and without this patch if I use 2.6.35.3 kernel from Freescale.
Thanks for testing, Lauri.
Quoted 7 lines
I think the issue with cpufreq still happens for you on 2.6.35 because you may use a different DDR model/topology than the one in mx28evk.
Stefano,
Since this patch does not cause any problems and does fix the 2.6.35 boot on mx28evk, is it possible to apply it for 2013.04?
Agree - I merge it.
Regards,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH v2 1/1 mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
In reply to Fabio EstevamQuoted 5 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
Currently the following kernel hang happens when loading a 2.6.35 kernel from Freeescale on a mx28evk board:
Quoted 8 lines
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registeredmxs_cpu_init: cpufreq init finished
...
Applied to u-boot-imx, thanks.
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================