configs: mx28evk: Use single-line comments

index dd0ef21..300bce9 100644
@@ -19,9 +19,7 @@
 #ifndef __MX28EVK_CONFIG_H__
 #define __MX28EVK_CONFIG_H__
 
-/*
- * SoC configurations
- */
+/* SoC configurations */
 #define CONFIG_MX28				/* i.MX28 SoC */
 
 #define CONFIG_MXS_GPIO			/* GPIO control */

@@ -35,9 +33,7 @@
 #define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_ARCH_MISC_INIT
 
-/*
- * SPL
- */
+/* SPL */
 #define CONFIG_SPL
 #define CONFIG_SPL_NO_CPU_SUPPORT_CODE
 #define CONFIG_SPL_START_S_PATH	"arch/arm/cpu/arm926ejs/mxs"

@@ -46,9 +42,7 @@
 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 #define CONFIG_SPL_GPIO_SUPPORT
 
-/*
- * U-Boot Commands
- */
+/* U-Boot Commands */
 #include <config_cmd_default.h>
 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DOS_PARTITION

@@ -70,9 +64,7 @@
 #define CONFIG_CMD_BOOTZ
 #define CONFIG_CMD_I2C
 
-/*
- * Memory configurations
- */
+/* Memory configurations */
 #define CONFIG_NR_DRAM_BANKS		1		/* 1 bank of DRAM */
 #define PHYS_SDRAM_1			0x40000000	/* Base address */
 #define PHYS_SDRAM_1_SIZE		0x40000000	/* Max 1 GB RAM */

@@ -98,9 +90,7 @@
 #define CONFIG_SYS_TEXT_BASE	0x40000100
 
 #define CONFIG_ENV_OVERWRITE
-/*
- * U-Boot general configurations
- */
+/* U-Boot general configurations */
 #define CONFIG_SYS_LONGHELP
 #define CONFIG_SYS_PROMPT	"MX28EVK U-Boot > "
 #define CONFIG_SYS_CBSIZE	1024		/* Console I/O buffer size */

@@ -115,23 +105,17 @@
 #define CONFIG_CMDLINE_EDITING		/* Command history etc */
 #define CONFIG_SYS_HUSH_PARSER
 
-/*
- * Serial Driver
- */
+/* Serial Driver */
 #define CONFIG_PL011_SERIAL
 #define CONFIG_PL011_CLOCK		24000000
 #define CONFIG_PL01x_PORTS		{ (void *)MXS_UARTDBG_BASE }
 #define CONFIG_CONS_INDEX		0
 #define CONFIG_BAUDRATE			115200	/* Default baud rate */
 
-/*
- * DMA
- */
+/* DMA */
 #define CONFIG_APBH_DMA
 
-/*
- * MMC Driver
- */
+/* MMC Driver */
 #define CONFIG_ENV_IS_IN_MMC
 #ifdef CONFIG_ENV_IS_IN_MMC
  #define CONFIG_ENV_OFFSET	(256 * 1024)

@@ -146,9 +130,7 @@
 #define CONFIG_MXS_MMC
 #endif
 
-/*
- * NAND Driver
- */
+/* NAND Driver */
 #ifdef CONFIG_CMD_NAND
 #define CONFIG_NAND_MXS
 #define CONFIG_SYS_MAX_NAND_DEVICE	1

@@ -156,9 +138,7 @@
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #endif
 
-/*
- * Ethernet on SOC (FEC)
- */
+/* Ethernet on SOC (FEC) */
 #ifdef	CONFIG_CMD_NET
 #define CONFIG_NET_MULTI
 #define CONFIG_ETHPRIME	"FEC0"

@@ -169,16 +149,12 @@
 #define CONFIG_MX28_FEC_MAC_IN_OCOTP
 #endif
 
-/*
- * RTC
- */
+/* RTC */
 #ifdef	CONFIG_CMD_DATE
 #define	CONFIG_RTC_MXS
 #endif
 
-/*
- * USB
- */
+/* USB */
 #ifdef	CONFIG_CMD_USB
 #define	CONFIG_USB_EHCI
 #define	CONFIG_USB_EHCI_MXS

@@ -197,9 +173,7 @@
 #define CONFIG_SYS_I2C_SPEED	400000
 #endif
 
-/*
- * SPI
- */
+/* SPI */
 #ifdef CONFIG_CMD_SPI
 #define CONFIG_HARD_SPI
 #define CONFIG_MXS_SPI

@@ -233,9 +207,7 @@
 #endif
 #endif
 
-/*
- * Boot Linux
- */
+/* Boot Linux */
 #define CONFIG_CMDLINE_TAG
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_BOOTDELAY	1

@@ -244,9 +216,7 @@
 #define CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR
 #define CONFIG_OF_LIBFDT
 
-/*
- * Extra Environments
- */
+/* Extra Environments */
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"update_nand_full_filename=u-boot.nand\0" \
 	"update_nand_firmware_filename=u-boot.sb\0"	\