mx6: Add solo-lite variant support
Subsystems (2)
A message that is not in the archive (sent off-list or not yet received): 1365622378-11196-1-git-send-email-a
festevam at gmail.com
reviewerPATCH v3 2/3 mx6: Add solo-lite variant support
From: Fabio Estevam <[email protected]>
mx6 solo-lite is another member of the mx6 series.
For more information about mx6 solo-lite, please visit:
http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=i.MX6SL&nodeId=018rH3ZrDRB24A
---
Changes since v2:
- None
Changes since v1:
- None
arch/arm/cpu/armv7/mx6/clock.c | 38 ++++++++++++++++- arch/arm/include/asm/arch-mx6/crm_regs.h | 5 +++ arch/arm/include/asm/arch-mx6/imx-regs.h | 63 +++++++++++++++++++++++++++- arch/arm/include/asm/arch-mx6/mx6-pins.h | 4 ++ arch/arm/include/asm/arch-mx6/mx6sl_pins.h | 25 +++++++++++ 5 files changed, 132 insertions(+), 3 deletions(-) create mode 100644 arch/arm/include/asm/arch-mx6/mx6sl_pins.h
arch/arm/cpu/armv7/mx6/clock.c +36 -2
@@ -186,12 +186,16 @@ static u32 get_ipg_per_clk(void)static u32 get_uart_clk (void ) {u32 reg, uart_podf; - +u32 freq =PLL3_80M ; reg =__raw_readl (&imx_ccm->cscdr1); +#ifdef CONFIG_MX6SL +if (reg &MXC_CCM_CSCDR1_UART_CLK_SEL ) + freq =MXC_HCLK ; +#endif reg &=MXC_CCM_CSCDR1_UART_CLK_PODF_MASK ; uart_podf = reg >>MXC_CCM_CSCDR1_UART_CLK_PODF_OFFSET ; -return PLL3_80M / (uart_podf +1 ); +return freq / (uart_podf +1 ); }static u32 get_cspi_clk (void )
@@ -252,6 +256,35 @@ static u32 get_emi_slow_clk(void)return root_freq / (emi_slow_pof +1 ); } +#ifdef CONFIG_MX6SL +static u32 get_mmdc_ch0_clk (void ) +{ +u32 cbcmr =__raw_readl (&imx_ccm->cbcmr); +u32 cbcdr =__raw_readl (&imx_ccm->cbcdr); +u32 freq, podf; + + podf = (cbcdr &MXC_CCM_CBCDR_MMDC_CH1_PODF_MASK ) \ + >>MXC_CCM_CBCDR_MMDC_CH1_PODF_OFFSET ; + +switch ((cbcmr &MXC_CCM_CBCMR_PRE_PERIPH2_CLK_SEL_MASK ) >> +MXC_CCM_CBCMR_PRE_PERIPH2_CLK_SEL_OFFSET ) { +case 0 : + freq =decode_pll (PLL_BUS ,MXC_HCLK ); +break ; +case 1 : + freq =PLL2_PFD2_FREQ ; +break ; +case 2 : + freq =PLL2_PFD0_FREQ ; +break ; +case 3 : + freq =PLL2_PFD2_DIV_FREQ ; + } + +return freq / (podf +1 ); + +} +#else static u32 get_mmdc_ch0_clk (void ) {u32 cbcdr =__raw_readl (&imx_ccm->cbcdr);
@@ -260,6 +293,7 @@ static u32 get_mmdc_ch0_clk(void) return get_periph_clk() / (mmdc_ch0_podf + 1); } +#endif static u32 get_usdhc_clk (u32 port) {
arch/arm/include/asm/arch-mx6/crm_regs.h +5 -0
@@ -244,7 +244,12 @@ struct mxc_ccm_reg {#define MXC_CCM_CSCDR1_USBOH3_CLK_PRED_MASK (0x7 << 8)#define MXC_CCM_CSCDR1_USBOH3_CLK_PODF_OFFSET 6#define MXC_CCM_CSCDR1_USBOH3_CLK_PODF_MASK (0x3 << 6) +#ifdef CONFIG_MX6SL +#define MXC_CCM_CSCDR1_UART_CLK_PODF_MASK 0x1F +#define MXC_CCM_CSCDR1_UART_CLK_SEL (1 << 6) +#else #define MXC_CCM_CSCDR1_UART_CLK_PODF_MASK 0x3F +#endif #define MXC_CCM_CSCDR1_UART_CLK_PODF_OFFSET 0/* Define the bits in register CS1CDR */
arch/arm/include/asm/arch-mx6/imx-regs.h +62 -1
136 lines not on this page · raw message
arch/arm/include/asm/arch-mx6/mx6-pins.h +4 -0
@@ -24,7 +24,11 @@#if defined(CONFIG_MX6DL ) || defined(CONFIG_MX6S )#include "mx6dl_pins.h" #else +#if defined(CONFIG_MX6SL ) +#include "mx6sl_pins.h" +#else #error "Please select cpu" +#endif /* CONFIG_MX6SL */ #endif /* CONFIG_MX6DL or CONFIG_MX6S */ #endif /* CONFIG_MX6Q */
arch/arm/include/asm/arch-mx6/mx6sl_pins.h new file +25 -0
@@ -0,0 +1,25 @@ +/* +* Copyright (C) 2013 Freescale Semiconductor, Inc. All Rights Reserved. +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +*/ + +#ifndef __ASM_ARCH_MX6_MX6SL_PINS_H__ +#define __ASM_ARCH_MX6_MX6SL_PINS_H__ + +#include <asm/imx-common/iomux-v3.h> + +enum { +MX6_PAD_SD2_CLK__USDHC2_CLK =IOMUX_PAD (0x055C ,0x0254 ,0 ,0x0000 ,0 ,0 ), +MX6_PAD_SD2_CMD__USDHC2_CMD =IOMUX_PAD (0x0560 ,0x0258 ,0 ,0x0000 ,0 ,0 ), +MX6_PAD_SD2_DAT0__USDHC2_DAT0 =IOMUX_PAD (0x0564 ,0x025C ,0 ,0x0000 ,0 ,0 ), +MX6_PAD_SD2_DAT1__USDHC2_DAT1 =IOMUX_PAD (0x0568 ,0x0260 ,0 ,0x0000 ,0 ,0 ), +MX6_PAD_SD2_DAT2__USDHC2_DAT2 =IOMUX_PAD (0x056C ,0x0264 ,0 ,0x0000 ,0 ,0 ), +MX6_PAD_SD2_DAT3__USDHC2_DAT3 =IOMUX_PAD (0x0570 ,0x0268 ,0 ,0x0000 ,0 ,0 ), +MX6_PAD_UART1_RXD__UART1_RXD =IOMUX_PAD (0x05A0 ,0x0298 ,0 ,0x07FC ,0 ,0 ), +MX6_PAD_UART1_TXD__UART1_TXD =IOMUX_PAD (0x05A4 ,0x029C ,0 ,0x0000 ,0 ,0 ), +}; +#endif /* __ASM_ARCH_MX6_MX6SL_PINS_H__ */
Signature · 1 line
1.7.9.5
festevam at gmail.com
reviewerPATCH v2 3/3 mx6sl: Add initial support for mx6slevk board
In reply to a message not in the archiveFrom: Fabio Estevam <[email protected]>
mx6slevk board is a development board from Freescale based on the mx6 solo-lite processor.
For details about mx6slevk, please refer to:
http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=IMX6SLEVK&parentCode=i.MX6SL&fpsp=1
---
Changes since v2:
- Total RAM is 1GB, not 512MB
Changes since v1:
- None
MAINTAINERS | 1 + board/freescale/mx6slevk/Makefile | 28 +++++ board/freescale/mx6slevk/imximage.cfg | 118 ++++++++++++++++++++ board/freescale/mx6slevk/mx6slevk.c | 102 ++++++++++++++++++ boards.cfg | 1 + include/configs/mx6slevk.h | 189 +++++++++++++++++++++++++++++++++ 6 files changed, 439 insertions(+) create mode 100644 board/freescale/mx6slevk/Makefile create mode 100644 board/freescale/mx6slevk/imximage.cfg create mode 100644 board/freescale/mx6slevk/mx6slevk.c create mode 100644 include/configs/mx6slevk.h
MAINTAINERS +1 -0
@@ -665,6 +665,7 @@ Fabio Estevam <[email protected]> mx6qsabresd i.MX6Q mx6qsabreauto i.MX6Q wandboard i.MX6DL/S + mx6slevk i.MX6SL Daniel Gorsulowski <[email protected]>
board/freescale/mx6slevk/Makefile new file +28 -0
@@ -0,0 +1,28 @@ +# (C) Copyright 2013 Freescale Semiconductor, Inc. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := mx6slevk.o + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +#########################################################################
board/freescale/mx6slevk/imximage.cfg new file +118 -0
118 lines not on this page · raw message
board/freescale/mx6slevk/mx6slevk.c new file +102 -0
102 lines not on this page · raw message
boards.cfg +1 -0
@@ -257,6 +257,7 @@ mx6qarm2 arm armv7 mx6qarm2 freesca mx6qsabreauto arm armv7 mx6qsabreauto freescale mx6 mx6qsabreauto:IMX_CONFIG=board/freescale/mx6qsabreauto/imximage.cfg mx6qsabrelite arm armv7 mx6qsabrelite freescale mx6 mx6qsabrelite:IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg mx6qsabresd arm armv7 mx6qsabresd freescale mx6 mx6qsabresd:IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg +mx6slevk arm armv7 mx6slevk freescale mx6 mx6slevk:IMX_CONFIG=board/freescale/mx6slevk/imximage.cfg,MX6SL eco5pk arm armv7 eco5pk 8dtech omap3 nitrogen6dl arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL,DDR_MB=1024 nitrogen6dl2g arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl2g.cfg,MX6DL,DDR_MB=2048
include/configs/mx6slevk.h new file +189 -0
189 lines not on this page · raw message
Signature · 1 line
1.7.9.5